Search Documents

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By J. van Zyl, K. B. Le Bron, L. J. Gardner

Pillar design is a crucial aspect of underground mining engineering, as it directly impacts the safety, stability, and overall effectiveness of mining operations. In this paper we present a method to calculate pillar stability based on the strain criterion and pillar load inversion concept, which complements the empirical pillar strength formulae. Those formulae do not account for certain parameters that can affect the stability of the pillars, e.g. weak layers, changes in stress orientations due to mining, orebody dip, mining layout complexity, and the influence of regional stabilizing pillars. The approach presented here is not intended to replace the empirical method; rather, we suggest using it as the initial step in the pillar design process. This should be followed by iterative numerical modelling to study pillar behaviour, define pillar stability, and optimize the pillar design by considering site-specific and representative rock mass properties and criteria.

Jun 10, 2024

By John W. Harbaugh, Alfredo Prelate

The goal of the study described here is to develop objective. quantitative methods for estimating the outcome probabilities of exploratory oil wells. The study employs the 're-experience' approach, in which historical data are used in a manner which attempts to recreate the past. Our past experience, of course, is the principal guide to the future. To appraise present-day oil prospects, however, we must analyze prospects that have been drilled in terms of how these former prospects were interpreted before they were drilled. An analysis of how they are interpreted after they were drilled is an inadequate guide to the future because our hindsight knowledge is superior to our foresight knowledge. Objective calculation of future outcome probabilities, then, requires that we attempt to treat past information in a manner analogous to that in which we must treat present information in forecasting future outcomes.

Jan 1, 2014

By U. König, N. Norberg

Ore mineralogy defines the properties during processing and metal extraction. Fast and frequent monitoring of the mineral content and related process parameters brings value to the mining operation and material processing. Decreasing ore qualities and increasing prices for raw materials require a better control of processed ore and a more efficient use of energy. Traditionally quality control in mining industries has relied on time consuming wet chemistry or the analysis of the elemental composition. The mineralogy that defines the physical properties is often monitored infrequently, if at all. The use of highspeed detectors has turned X-ray diffraction (XRD) into an important tool for fast and accurate process control. XRD data and their interpretation make the difference in the identification of minerals, in describing their distribution in ore bodies and in their beneficiation during processing. The use of statistical techniques such as Partial Least-Squares Regression (PLSR) or Principal Component Analysis (PCA) on XRD raw data has been successfully trialled to determine raw materials and processed ores, in addition to well established methods for mineral identification and quantification. PLSR can be used to correlate process parameters directly from the XRD pattern without investigating the mineral content. Hidden information present in the XRD pattern but not determined with traditional methods can be used to improve the characterisation of the analysed materials. The practical use for the direct determination of process relevant parameters during exploration and ore beneficiation will be illustrated in several case studies from mining and ore processing. Keywords: Geometallurgy, mineral monitoring, X-ray diffraction, process efficiency

Jan 1, 2020

By J. P. Gouvea, T. R. Stacey

A research project was carried out on a gold mine in the Vaal River region of South Africa (Witwatersrand Basin) to evaluate the effect of two particular aspects of rockbolt installation – the angle of inclination of the bolt relative to the orientation of the rock surface, and the protruding length of the bolt – on the mine’s gully support system. A keyblock analysis approach indicated that these factors do not have an adverse impact on the stability of the strike gullies. This was confirmed by extensive empirical data collected from the case study mine. While safety is the primary concern, cost saving opportunities can be realized through reconsidering historically inherited support standards that are perceived to be correct and appropriate. The research described in this paper sets forth a practical approach, that is easy to implement and repeatable, to evaluate the role of rockbolts in stoping gullies.

Feb 12, 2024

By R. B. Khumalo, M. S. Nyarela, R. C. Nemathithi

Palabora Mining Company is one of the largest low-grade copper mines globally. The mine uses block caving for the extraction of the orebody. This paper enumerates the drawpoint loading strategies for the overall head grade improvements, particularly for a block that is nearing depletion. A comprehensive literature review of various considerations relating to improving productivity in block caving is presented to contextualize the draw control in caving. From this study, an optimized draw control strategy is presented, which focuses on three parameters that include grade distribution, loading compliance, and tonnage splits per sector. An empirical method based on the relational study between various parameters is used to outline the key criteria to be used in the optimization of drawpoint loading in block caving.

Nov 30, 2022

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009

By N. K. Singo, J. D. Kramers

The reprocessing of tailings resources to extract gold on an industrial scale has become common practice. While these projects are common in the Witwatersrand basin, similar low-technology processes are not operational in smaller goldfields. This study explores the possibility of reclaiming the tailings dump of the Louis Moore Mine in the Giyani Greenstone Belt, investigates potential hazards to communities in the vicinity, and identifies mitigation strategies. Auger samples were taken from the Louis Moore tailings at depths of up to 5 m. Aqua regia leach analyses show Au concentrations of up to 1 g/t. Inferred estimations based on ordinary kriging (OK) and inverse distance weighted (IDW) methods put the residual Au resource in the Louis Moore tailings dump at 0.20 t. Reworking the tailings is viable, although a potential environmental risk exists in the form of elevated arsenic concentrations. Further exploration is required to determine the mineralogical associations of Au and As. Tailings reworking would assist in raising funds for mine rehabilitation. The secondary tailings could potentially be repurposed, which would provide employment and facilitate community development, as well as deliver environmental benefits.

Jul 1, 2021

By J. R. Bredell, J. Branehog, C. Coetzee, J. J. van Tonder

A nutating grinding mill, exemplified by the commercial HICOM mill, achieves efficient particle size reduction through the accelerated motion of the material charge within the nutating chamber. This design, characterised by high particle velocities and rapid charge circulation, offers a compact solution compared to tumbling mills. There have been concerns regarding the mechanical reliability of kinetic joints for certain specialised mining applications. Recognising the need to model internal forces in such systems, this study focuses on the uncoupled simulation using multibody dynamics and the discrete element method. The investigation employed a small-scale experimental test mill, referred to as the NuMILL, featuring a cylindrical chamber (140 mm internal diameter, 245 mm height, 6° nutation angle). Instrumented with an array of sensors, the NuMILL provided internal load data for validating the simulations. Experiments were conducted with an empty chamber or filled with charge material. Charge materials included coarse sand or steel pellets with a charge-to-chamber mass ratio of 0.25. The mill speed ranged between 100 to 700 RPM. Multibody dynamics modelled resultant inertial and frictional loads within 5%, while the discrete element method simulated the internal material contact loads with accuracies ranging from 1% to 19%. The combined simulation approach predicted the resultant forces in the critical kinetic joint within a 20% margin. Representing the charge using rigid lumped mass elements was also studied. The presented simulation techniques, validated against experimental data, offer a robust foundation for analysing larger systems, including the industrial-scale HICOM.

Mar 5, 2025

By D. Paktunc, S. P. du Preez, J. P. Beukes, P. G. van Zyl, A. Jordaan

"The chromium (Cr) content of stainless steel originates from recycled scrap and/or ferrochrome (FeCr), which is produced mainly by the carbothermic reduction of chromite ore. The oxidative sintered pellet production process is one of the most widely applied FeCr processes. The supplier of this technology specifies that recycling of chromite-containing dust collected from the pellet sintering off-gas and fines screened out from the sintered pellets (collectively referred to as pre-oxidized chromite fines) should be limited to a maximum of 4 wt% of the total pellet composition. However, the results presented in this paper suggest that recycling of such fines up to a limit of 32 wt% of the total pellet composition may improve the compressive and abrasion strengths of the cured pellet. In addition, electron microprobe and quantitative X-ray diffraction (XRD) analyses demonstrate that chromite grains present in the pre-oxidized chromite fines consist, at least partially, of crystalline phases/compounds that will improve the metallurgical efficiency and specific electricity consumption (i.e. MWh/ton FeCr produced) of the smelting process. Introduction Stainless steel is a vital modern-day alloy that is well-known for its corrosion resistance, which is mainly due to the inclusion of chromium (Cr) (ICDA, 2013). Stainless steel is mostly produced from recycled scrap and ferrochrome (FeCr), a relatively crude alloy of Cr and iron (Fe). FeCr is predominantly produced by the carbothermic reduction of chromite, a mineral belonging to the spinel group characterized by the unit formula [(Mg,Fe2+)(Al,Cr,Fe3+)2O4] (Haggerty, 1991; Paktunc and Cabri, 1995; Tathavakar, Antony, and Jha, 2005). Although Cr can occur in 82 different minerals, chromite is the only source of new Cr units that can be exploited in commercial volumes (Motzer and Engineers, 2004). Approximately 95% of mined chromite is used in the production of various FeCr grades, of which high-carbon and charge grade FeCr are the most common (ICDA, 2013)."

Feb 1, 2019

By S. Plaatjie, L. Linzer, M. S. D. Manzi, M. Sihoyiya

Fiber-Optic Sensing and UAV-Platform Techniques for Innovative Mineral Exploration (FUTURE) is a joint European Union and South African consortium project funded under ERA-NET Cofund ERA-MIN3. The project aims to develop cost-effective and novel seismic methods to image geological structures ahead of the mine face, ultimately leading to improved decision-making and safer mining practices. In this study we present results from numerical simulations conducted at South Deep Gold Mine for active in-mine seismic surveys. The study uses a finite differencing code known as WAVE3D, which models models the propagation of a seismic wave generated by stress pertubations that are applied to a defined grid. The numerical simulation model included two major ore bodies (Black Reef and Ventersdorp Contact Reef) and mine tunnels. The model was constrained using laboratory physical property measurements from underground borehole samples such as seismic velocities (e.g., compressional and shear waves) and bulk densities. Two case studies were created, one modelled the active shots and receivers on surface, and the other modelled the shots at depth (in a mine tunnel at ~4000 m depth) with receivers on surface. In both cases, the objective was to investigate the wavefield propagation through the rockmass between the mine tunnel and surface. The simulated wavefield produced by the source located along the mine tunnel was successfully recorded on surface. The surface-recorded wavefield exhibits clear one-way P-wave arrival times at approximately 450 ms to 500 ms, which can be used to calculate the surface-tunnel P-wave refraction tomogram. The results from the study were used to constrain the design, and for the acquisition and processing of the real surface and in-mine seismic surveys acquired under the FUTURE project.

Jan 12, 2025

By B. A. Obadele, R. Machaka, M. L. Raganya, M. E. Makhatha, N. A. Moshokoa

The influence of solution treatment on the phase evolution and tensile properties of Ti-Mo alloys was investigated to assess their potential use in biomedical applications. Phase formation and microstructural evolution were studied using X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The mechanical properties were characterized by means of tensile tests and bending strength. XRD analysis showed that solution treatment increased the volume fraction of β phase and supressed the α" phase. The microstructures of the as-cast alloys consisted of β equiaxed grains with sub-grain structures of different sizes, while the solution treated alloys comprised β equiaxed grains only except for Ti- 10.02Mo, which comprised needle-like α" structures. EBSD showed an increase in the volume fraction of the ω and α" phases in all the alloys after solution treatment. The elastic modulus and UTS of all the alloy significantly decreased after solution treatment, except for Ti-15.05Mo,whereas the elongation significantly increased. The fracture surfaces of all the alloys after solution treatment indicated more ductile behaviour than brittle

Jun 10, 2024

By G. P. Dyke

With the removal of the majority of the shallow mineral reserves there has been an increase in the mining depths in the South African mining industry. This has, in turn, changed the industry?s and stakeholders? perceptions of risk associated with mining-induced instability. In recent years the increased mining depth, particularly in open pits, has led to an increase in pit slope failures, which has highlighted the need for appropriate and effective pit slope management programmes. Such a programme comprises many facets, including mine hazard plans, regular slope inspections, cleaning of interim and final pit faces, blasting practices, histories of failures, pit depressurization, stormwater control and evacuation procedures. However, it is arguably in the field of slope monitoring that the most significant strides have been made in terms of new technologies and best practice in open pit mining geotechnics, with the introduction of technologies such as laser scanners and slope stability radar. This paper seeks to illustrate the operational benefits associated with the implementation of new technologies into open pit mining, using AngloGold Ashanti?s Geita Gold Mine in Tanzania as an example.

Jan 1, 2009

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By C. A. Border

This paper is a brief record of the State's involvement in the problems that have faced Iow-grade mines in the South African gold-mining industry for a period of more than sixty years. Not all the recommendations made by the various commissions are recorded here, but those which are included highlight the fact that many of the problems that plagued the industry during those years, whether economic or labour matters, are still troubling the industry today.

Jan 1, 1981

By M. Kumral, Y. A. Sari

Underground mining operations tend to have higher operating costs than surface mines. When metal prices decrease, profitability is jeopardized due to the high costs. Therefore, mining management harnesses new practices that increase operational efficiency. One way to manage this challenge is to invest in new mine planning practices. Stope layout optimization as a part of underground mine planning aims to identify a portion of the orebody in the form of production volumes (stopes) to maximize profit under roadway and stope dimension constraints. In this paper we propose a novel approach based on identifying ore-rich areas of the deposit and prioritizing their extraction through an iterative heuristic clustering approach. The proposed approach is compared with and validated by an exact method through a small mining example. The heuristics produced nearly identical results in a very short time. Finally, a case study was carried out using a larger data-set. The cluster-based iterative approach generated nearoptimal stope layouts in a computationally effective manner.

Mar 1, 2021

By S. J. Baumgartner

The ferromanganese industry is under pressure to deal with the slag arising from the production of ferromanganese, which is discarded in landfills or slag heaps. This material poses an environmental and health risk to surrounding ecosystems and communities, and disposal costs are increasing. Ferromanganese slag contains an appreciable amount of residual manganese metal, which can be exploited. Previous work has shown that the slag can be leached fully, while rejecting the silica to a residue. The methods that were investigated to recover manganese from the leach solution included hydroxide precipitation to upgrade the leach solution followed by manganese carbonate precipitation to produce a pure manganese carbonate product or a manganese carbonate furnace feed material, which would be recycled to increase manganese recoveries in the production of ferromanganese. In addition, electrowinning of electrolytic manganese dioxide from the leach solution was studied. The methods were compared in terms of selectivity, costs, and product quality. Co-recovery of the leach residue, which is a potential cement additive, is discussed. Among the methods investigated to upgrade the pregnant leach solution, hydroxide precipitation utilizing ammonia to adjust the pH appears to be the most effective in removing major impurities such as iron, aluminium, and silica to less than 1 ppm. The manganese carbonate and impure manganese carbonate furnace feed products met quality specifications. However, although the production of these materials was technically viable, the large amounts of base reagent that were required to raise the pH, and the associated high operating costs, rendered the process uneconomic. An optimization study was therefore carried out with the primary objective to determine the ideal acid amount to be utilized in the waterstarved digestion stage, thereby decreasing acid and base consumption while optimizing the quality of the pregnant leach solution, and producing a leach residue that contained <1% Mn. The outcome was an economically viable process. Additional benefits included an increase in the manganese content of the impure manganese carbonate furnace feed material, and a substantial reduction in the dilution of the pregnant leach solution, thereby maintaining high manganese concentrations that rendered the solution viable for electrowinning of electrolytic manganese dioxide, the production of which yielded a current efficiency of 74%.

Jan 1, 2014

By C. Musingwini

The South African mining industry continues to be a major source of employment at a time when at least 25 per cent of the working age population is unemployed. At the same time the industry faces a skills shortage in many of the disciplines necessary for its future health. The University of the Witwatersrand, University of Pretoria, University of Johannesburg, and University of South Africa have historically produced mining graduates for the South African industry, with any shortfall being met by the recruitment of overseas graduates. More recently the global shortage of engineers and other mining industry professionals has seen a reversal of this trend and a very significant emigration of well-educated and highly skilled personnel. The traditional career path for mining graduates is in production and mine management. However, there is the parallel and possibly more pressing need for specialized skills in such fields as ventilation, rock engineering, mine planning, mineral resource evaluation, and mineral asset valuation. It is in these essential areas that chronic shortages continue to hamper the development of the industry and may well frustrate its ambitions to be safe, healthy, and profitable into the future. The permeability of skills across sectorial boundaries within the mining industry requires that skills shortages in the platinum sector are not looked at in isolation, but within the context of the entire industry. This paper reviews the efforts being made by the universities at both undergraduate and postgraduate levels to meet the needs of the South African mining industry, in terms of the required numbers and the range of specialized skills.

Jan 1, 2012

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016