Search Documents

By U. Sachse

This paper explores a systematic approach for mining decision-makers to use when faced with choosing which method to use for a specific rockpass length. The different excavation methods available in the broad South African mining industry are compared against a number of critical parameters, as applied to rockpasses of varying length. This approach is not meant as a definitive, prescriptive planning tool, but rather as a proposed approach to enable designers and planners to choose the best system to excavate their specific rockpasses

Jan 1, 2005

Viscosity measurements were carried out on slags in the CaO-Cu2O-CuO-MgO-SiO2systemcontaining ~ 63 wt% SiO2in air. The experimental work was carried out over a range of temperatures where the slags were completely liquid. Initial measurements were on a binary CaO-SiO2slag to which incremental additions of CuxO-MgO-SiO2slag with the same silica mole fraction were made. The viscosity-temperature relationship was measured for slags with‘Cu2O’contents of 0.02, 0.19, 0.38, 0.79, 1.69, 2.47, 3.01, 5.31 and 10.0 wt%. The proportions of Cu+and Cu2+in the slags were determined. The oxidation state of Cushifted from predominantly Cu+to Cu2+, with the Cu+/Cu2+ratio of approximately 0.3 for slag with a Cu content above 2 wt%. This is equivalent to Cu1.13O. The trends observed for changes of Cu2+/Cu+redox ratio with slag chemistry were consistent with the literature. Decreasing the CaO content by substituting copper oxide resulted in a decrease in the Cu+/Cu2+redox ratio. The change in ratio corresponded to a shift of the value of x in CuxO from an initial value of 1.8 to 1.1,when the slags contained 10% ‘Cu2O’. In this study, the SiO2content of the slags varied between 64 and 60 wt% as the Cu content increased. The viscosity of the slag containing 10 wt% CuxO was nearly 4.5 times lower than the binary CaO-SiO2slag. As the silica mole fraction (xSiO2) actually stayed constant (0.61±0.009),the results show that CuxO acted as a network breaker. Comparison with other ternary slags with similar silica mole fractions suggest that that addition of CuxO to silicate slags has a stronger effect on lowering the viscosity than FeO or MnO has on a molar basis. Keywords: viscosity, copper, silicate, slags

Jan 1, 2004

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

By A. Bhattacherjee

The Shewhart [X]?and R charts are still the most popular control charts in use today for continuous monitoring of quality data. However, for these charts to function properly, the underlying assumption of normality and independence of data must be satisfied. When either independence and/or normality of data are not present, which is a common feature of ore quality data, an application of the conventional Shewhart [X]?and R charts may introduce false alarms in the analysis of the data. To address these issues, a guideline is proposed for construction of appropriate univariate and multivariate control charts for a variety of situations. A use of this guideline to a bauxite mine suggested the construction of special cause control chart for the analysis of individual variables namely, Al2O3% and SiO2%; whereas, the multivariate T2 chart based on residuals is proposed for the bivariate analysis of the variables. The case study clearly revealed that without considering the data correlation, one may be in a state of false impression about an out of control condition while using the Shewhart [X]?and R charts for univariate and the Hotelling T2chart for multivariate analysis. To compare the effectiveness of the control charts, specifically the Shewhart [X]?and the special cause control charts, a simulation study was conducted. It was found that the conventional Shewhart chart provided lower probability of coverage than the special cause control chart. It was also revealed that the quality specification of Al2O3% is met as the variation of Al2O3% is well within the specification limits; whereas, it is difficult to meet the quality specification of SiO2% on a regular basis.

Jan 1, 2002

By S. Sun

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest is reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi-component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By R. Altindag

The rock brittleness is one of the most important rock properties that affect the drill-ability of rocks. It is supposed that the increase in rock brittleness causes the increase in penetration rate. The drill-ability of rocks depends on many factors. These factors can be separated as two parts depending on a machine, bit type, rotational speed, thrust, blow frequency, flushing, and rock properties, brittleness, compressive strength, structure, hardness, etc. In this paper, the relationship between brittleness and drill-ability index, which is used in the prediction analysis of the penetration rate of rotary blast hole drills, were examined using regression analysis. It is also seen that significant correlations exist between brittleness and the drill-ability index.

Jan 1, 2002

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By M. Vandewalle

What separates the support of mining openings from the support of similar civil engineering structures is the fact that mine openings have to survive large deformations as a result of changing stress conditions induced by progressive mining. Steel fibres impart to concrete and shotcrete a high degree of ductility which not only allows the shotcrete and concrete linings to absorb important rock movements but also to increase its bearing capacity by a redistribution of the loads. A range of applications will be discussed technically and economically.

Jan 1, 1998

By J. M. Cardoso, E. F. Quadros, A. Chiarini, F. Fernandes, G. Vilela, J. Ireno, L. C. Agostini

Based on the geological-geometric characterization of the basaltic rock at the site of a factory for chemical products situated in the Southern region of Brasil, and on results of a significant number of packer tests, the principal directions of flow were estimated, taking into consideration the intersection and the orientation of the joints and the amount of contaminant flow measured in each interval. The tests were performed using the multi-packer hydraulic multitest probe of IPT (HMTP) instrumented with an electric conductivity meter. A method of analysis for three-dimensional evaluation of the amount of contaminant flow in the area was proposed for future mitigation of the problem. Basé sur une caractérization géologique-géotechnique de la roche basaltique existant sur un site dune fabrique de produits chimiques située au sud du Brésil et sur les resultants dún nombre significantif déssais du type packer, les directions principales d´écoulement ont été estimées en considerant l´intersection et orientation des joints et la quantité de contaminant mesurée sur chaque intervale d´essais. Ceux-ci ont été realizes en utilisant une sonde multipacker developée au IPT – São Paulo (HMTP) instrumentée avec un mesureur de condictivité électrique. Une méthode d´analyse 3-D pour l´évaluation du transport du contaminant sur ce site a été proposée pour une future mitigation du problème. Auf Grund der geologischen Struktur des Basalts auf dem Gelände einer chemischen Fabrik in Südbrasilien und der Ergebnisse einer ansehnlichen Zahl von Pumpversuchen wurden die Hauptfließrichtungen bestimmt unter Berücksichtigung des Kluftgefüges und der in jedem Intervall gemessenen Menge kontaminierten Wassers. Die Versuche erfolgten mit dem im IPT entwickelten Verfahren (HMTP) mit Mehrfachpackern und elektrischen Leitfähigkeitsgebern. Ein analytisches Verfahren zur dreidimensionalen Ermittlung der Mengen kontaminierten Wassers wurde für die künftige Befassung mit dem Problem entwickelt.

Jan 1, 2003

By J. T. Kalala

Energy consumption and wear of grinding media and liners are the major cost factors in milling plants. Since the beginning of the last century, much effort has been directed at the prediction of the power draw as affected by the mill operating conditions. This paper explores the prediction of the liner wear using the discrete element method (DEM). A mathematical model taking into account adhesion, abrasion and impact wear which occur in dry mills is derived in order to predict the loss of material on liners. The mathematical model is implemented in the DEM code using an objective function in order to produce realistic simulated profiles. Our DEM simulated predictions are compared to published experimental and industrial data. Keywords: modelling; discrete element method; liner wear

Jan 1, 2004

By J. F. Reddick

The South African coal mining industry is currently disposing of about 10 million tons of ultra-fine coal (<150 µm) per year. Once discarded, these sulphur-containing ultra-fines contribute to several environmental problems. As part of a project initiated by the Water Research Commission to investigate the use of Cleaner Production (CP) in the mining industry, a study was carried out to determine whether a CP approach could be used to identify opportunities to reduce this coal waste, and to determine which of these opportunities would be most feasible. In order to do this, a CP assessment was conducted at three case study collieries in the South African Witbank coalfield. Mass-balancing and sampling, followed by laboratory characterisation tests and site surveys, were used to determine the quantity, quality and sources of the ultra-fine coal at the three collieries. Literature reviews, brainstorming sessions and interviews then followed to generate the CP options. An environ-mental, economic and technical feasibility assessment was then prepared for each option, to determine the most viable interventions for implementation. A number of opportunities were identified through the assessment. By preventing coarser coal from being discarded with the ultra-fine coal, the quantity of coal disposed of could be decreased at all three collieries, and by up to 24% in one case. Increasing the crusher top size would reduce the amount of coal that is milled to less than 150 µm, so that less is wasted. The ultra-fines that have already been disposed of on slurry dams can be completely reclaimed and converted into a valuable product, which can be sold as power station feedstock. The newly processed ultra-fines could be beneficiated using flotation and exported together with the coarser coal. The results of the assessments thus suggested that workable CP opportunities to reduce ultra-fine coal wastage exist at the sites investigated, and that their feasibility is colliery-specific. The associated financial benefits of the proposed options suggested that CP is a realistic approach to addressing environmental problems. Keywords: Cleaner Production; coal mining; coal-washing; ultra-fines

Jan 1, 2007

By J. W. Neale

Mintek and BacTech have joined forces to provide the metallurgical industry with bacterial-oxidation processes for the treatment of sulphide ores. The processes are aimed at both refractory gold-bearing and base-metal concentrates. Previously, BacTech had commercially implemented the refractory gold process at the Youanmi Gold Mine in Western Australia. More recently, the process has been incorporated in the Sulphide Treatment Plant at the Beaconsfield Gold Mine in Tasmania, Australia. In addition, Mintek and BacTech have recently signed an agreement with the Laizhou Gold Metallurgy Plant in China?s Shandong Province, which will see the third commercial realization of the technology for refractory gold. Development of the base-metal technology is the subject of several papers in the proceedings of this colloquium. The implementation of the refractory gold technology at Beaconsfield is discussed in detail. Some important aspects that are covered include: ?Test work, and the choice of bacterial culture ?Process design choices, and the advantages of the Mintek-BacTech process ?Inoculum build-up ?Plant commissioning ?Plant performance. Besides the Laizhou project, Mintek and BacTech are currently investigating several other commercial prospects for the technology. These include the use of the technology for a gold-copper deposit, where the production of both gold and copper is envisaged.

Jan 1, 2000

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2001

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

By M. M. Manamela

Paper written on project work carried out at the University of Pretoria in partial fulfilment of the requirements of the B Tech degree at the Tshwane University of Technology This work tested whether ore particle size affects the carbon-based pre-reduction of titaniferous magnetite. Pre-reduction is performed at a temperature of some 1100°C in a rotary kiln, in the Highveld Steel process. Laboratory isothermal reduction measurements were performed with ore-coal mixtures at this temperature, to test the effect of ore particle size. The results show that size does limit the degree of reduction for particles larger than 15 mm.

Jan 1, 2005

By J. A. Bakken, G. Sævarsdóttir, H. Pálsson, M. Þ. Jónsson

The role of the electric arc in the consumption of electrodes in submerged arc furnaces has long been debated. The hostile environment in the furnace does not make direct measurement feasible, so simulation has been used to evaluate the arcs contribution to the erosion. Magnetofluiddynamic (MFD) electric arc simulations and a cathode / anode sub-model developed in order to provide boundary condition to the arc model have been used for this purpose. The cathode / anode sub-model provides current distributions and cathode / anode fall voltages for the arc and temperature distribution for the electrode surface, which is paramount to the erosion rate which in turn is calculated from the Clausius Clapeyron equation and the Hertz Knudsen formula for the vapour transport. In the case of high-current industrial AC arcs, arc currents are typically ~100 kA, phase voltages ~100 V and total furnace power ~10 ? 60 MW. The results show that although enormous amounts of material is evaporated, much of it recondenses on the surface. Furthermore the results show that the arc erosion increases strongly with the arc current. If a single arc is present its contribution to erosion is close to the actual total erosion in the furnace. Results from this analysis indicate that there are possibly more than one arc present in the crater, in which case less than 40% of the total erosion would be due to the arc, the rest is chemical erosion.

Jan 1, 2007

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By M. H. Rogers

Coal has been at the forefront of mankind?s drive to improve his quality of life and also for sustainable development, from the Industrial Revolution onwards. The international coal industry today is large, with some 3,7 billion tons being produced and consumed in 1997. South Africa is an important participant in the coal industry, selling some 220 million tons in 1997 of which 64 million tons were exported. It is the second-largest thermal coal exporting country in the world. Despite the size of the world coal industry, it is not immune to change. The address examines growth projections for the industry and the change drivers that will impact on it in the future. Environmental pressures, the most important of which being the climate change debate, the Kyoto Protocol arising from this debate and the development of clean coal technologies, to reduce the impact of coal production and usage on the environment are considered. Other major change drivers considered are competition from other sources of energy and that between coal producers, the deregulation of the electric power industry, corporate restructuring and for the South African producer, legislative reform. The declining (real term) coal price, the consequent squeeze on margins and the need for producers to actively contain costs is covered. Technology has, in the past, been the driver behind the growth and change of the South African coal industry and its future role in ensuring that coal is the fuel of choice for continued improvement in standards of living and economic development is addressed.

Jan 1, 1999