Search Documents

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, the pH decreased and metals increased. Output pH increased from 4 to more than 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long-term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2002

By D. J. McCracken

The lithium review did not arrive in time for publication in the June issue The estimated consumption of lithium minerals as raw materials to the glass, ceramic and metallurgical industries in 1992 was 85.5 kt (94,200 st). That equates to about 12 kt (13,200 st) of lithium carbonate equivalent (LCE). An additional 150 kt to 200 kt (165,000 to 220,000 st), or 7.5 kt to 10 kt (8200 to 1100 st LCE), were used in the production of lithium chemicals. The 1992 consumption represents an overall decrease of 3.5 kt (3800 st), or 500 t (550 st) LCE, from 1991. This was a direct result of a worldwide reduction in glass demand due to the economic recession. There are three major producers of lithium minerals. Gwalia Consolidated Ltd. (formerly Lithium Australia Ltd.) in Western Australia and Tantalum Mining Corp. (Tanco) in Manitoba, Canada, both produce spodumene ore. Bikita Minerals, in Zimbabwe, is the largest producer of petalite. Bikita also has the capacity to produce small volumes of spodumene concentrate. The Cyprus Foote spodumene operation at Kings Mountain, NC, ceased production in 1992. It once produced about 2 kt/a (2200 stpy) of "high iron spodumene" for uses other than in the manufacture of lithium chemicals. The lithium products of the major producers are shown in Table 1. The current resources of 13 Mt (14.3 million st) of LCE in the western world will supply demand for more than 50 years.

Jan 1, 1993

By K. Hanumantha Rao, K. S. E. Forssberg, B. -M. Antti

Selective flotation of muscovite from a material containing muscovite (15.4%), biotite (13%), and siliceous gangue (quartz and feldspar), using a mixed collector system of sodium oleate and dodecylamine acetate has been described. Muscovite is found to float in preference to biotite, when the pulp is initially conditioned with oleate followed by amine at basic pH values. The results indicate that a product containing 63% muscovite with a recovery of 93% can be obtained, while using 75-150glt of oleate and 96 g/t of amine. The biotite grade and recovery are found to be around 30% and 20%, respectively. A good selectivity between muscovite and siliceous gangue is obtained. A final product containing 95% muscovite with an overall recovery of 75% is obtained when the flotation concentrate is subjected to magnetic separation. These studies indicate the possibility of separating muscovite from biotite by using a mixture of collectors.

Jan 1, 1991

By V. R. Manukonda, I. Iwasaki

Selective flocculation of iron ores is extremely sensitive to the type and amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and the selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1988

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By L. W. Saperstein, R. J. Sweigard, D. L. Simpson

Deep tillage is widely used as a means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids produced during deep tillage in order to prevent any significant recompaction from occurring. Various amendments were injected into the soil during laboratory tests using a small-scale ripping and injection system. Measurements were made of selected soil proper Pies to evaluate the feasibility of this method.

Jan 1, 1994

By Charles W. Daugherty, Eugene B. Waggoner

In the construction of recent subsurface projects, particularly mined openings and transit systems, it has been apparent that final costs were often greater than first expected. Because many overruns result from alleged differing site conditions, there was reason to suspect that pre-bid geotechnical investigations were inadequate for predicting subsurface geology. In 1982, nine federal agencies involved in constructing underground facilities funded the National Academy of Sciences' U.S. National Committee on Tunneling Technology (USNC/TT) in an effort to evaluate and clarify the relationship between geological knowledge and construction costs. That committee formed the special Subcommittee on Geological Site Investigations, which spent more than two years studying underground projects by examining contract documents and geologic reports, making site visits, and interviewing owners, designers and contractors. The study ultimately encompassed 84 mined tunnels and chambers and three deep shafts in the United States and eastern Canada. Data collected on geologic exploration, design and construction were analyzed and conclusions reached concerning whether and how site investigations need to be improved. The results of the study are published in two volumes by the National Academy of Sciences. Due to the recent completion date of the main report, it was not possible to prepare a summary for inclusion in the RETC Proceedings. However, the complete two-volume report, "Geotechnical Site Investigations for Underground Projects," can be obtained by writing or calling: U.S. National Committee on Tunneling Technology National Academy of Sciences 2101 Constitution Avenue, N.W. Washington, D.C. 20418 (202) 334-3136

Jan 1, 1985

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By G. E. Mellor, R. E. Lippoth, T. B. Faddies

The Little Rocky Mountains host epithermal- gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining these oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1) mineralization; 2) oxidation; 3) structural setting; 4) lithology; 5) alteration; and ultimately, 6) the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1992

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.

Jan 1, 2002

By Leonard W. Postregna

Prior to January, 1986, the city of Austin, Texas was on notice by the Federal Government's Environmental Protection Agency and the Texas Water Commission, that they were illegally polluting the Colorado River. The wastewater facilities presently in use in South Austin were inadequate to handle the vastly increasing population. The city of Austin, Texas hired Parsons Brinckerhoff Quade and Douglas, Inc. and Dannenbaum Engineering Corporation to design and supervise the construction of an update to their existing system to alleviate this problem. A major criterion handed down to the Designer and Contractor was that the system had to be completed within a two year time frame. The biggest link to the entire design was a tunnel project consisting of 43,000 linear feet (13,106 m) of tunnel, eight feet (2.44 m) in diameter with connecting structures tying into existing and future facilities. The project was awarded to S. A. Healy Construction Company of McCook, Illinois with a low bid of $24,755,000.00. This article summarizes the techniques used in the construction of this tunnel project.

Jan 1, 1989

By Edward F. Divers, J. Drew Potts

Powered dust-filtering helmets (dust helmets) have become increasingly prevalent in the underground mine environment in recent years. Many longwall operations use dust helmets to reduce the respirable dust exposures of miners required to work downwind of crusher, roof support and shearer operations. While continuous mining sections are usually less dusty, use of diesel equipment represents a new potential health problem. The U.S. Bureau of Mines recently conducted a study to determine the efficiency of a dust helmet on diesel-size particulate. Two underground evaluations were conducted on continuous mining sections that were using diesel haulage vehicles. Model No. AH21 Racal airstream helmets equipped with AS22-3 prefilters, AS23-3 main filters and AS60476 tyvek full-face seals were tested. Helmets were placed on mannequin heads and mounted in the ram car cabs. Andersen Model 298 (eight-stage) personal cascade impactors were used to sample air inside and outside of the helmet. Impactor stages 8 and the final filters were analyzed to determine submicrometer (0 - 0.93 µm) particle concentrations. Results from this study showed that the dust helmet was 94% (± 3% at 95% confidence level) efficient on submicrometer particles. Typically, very little coal dust is observed in the submicrometer size range, therefore, these particles were assumed to be from diesel exhaust. Results from this study indicate that proper use of the dust helmet on continuous mining sections that are using diesel haulage vehicles may be beneficial to the health of miners.

Jan 1, 1991

This research contributes to BioMinE (http://biomine.brgm.fr), an integrated European Union project of the Sixth Framework Programme. The general objective of BioMinE is the development and integration of innovative, environmentally friendly, biohydrometallurgical processes for the recovery of metals from primary and secondary resources within Europe. The work presented in this paper deals with the initial plan of study on the sustainable use of solid wastes derived from bio-processing of European metal bearing resources. The approach involves solidifying the waste into cementitious waste composites analogous to controlled low-strength materials (CLSM). The aim is to achieve composites of adequate mechanical, physicochemical and environmental integrity, thus providing a sustainable solution for dealing with such bulk products which are conventionally unmarketable and therefore normally discarded to landfill. Assessment has been based on largely ?model? wastes anticipated to be similar to bio-processing wastes. These include an ochreous mine water sludge and an industrial goethite residue. The work indicates that wastes containing high iron and calcium contents, typical of products from bioleaching of concentrates, could be beneficially reformed as CLSM of appropriate compressive strength. Due to the high water contents of these composites, porosity and hydraulic conductivity were correspondingly high. Flow-through leach tests showed some resistance to immobilisation of toxic elements. Work is continuing to reduce the risk of toxic elements leaching under environmental conditions. This will include laboratory-scale encapsulated systems of CLSM, designed and tested to produce a novel type of engineered fill structure.

Jan 1, 2006

By S. Frimpong, N. Demirel

Overburden excavation is an integral component of the surface mine production chain. The walking dragline is the most economic production equipment for overburden excavation in strip mining. Draglines are capital intensive, and thus, investments in multiple units severely impact the economic viability of projects. The use of few dragline units results in highly concentrated production focus, which must be efficiently managed to derive the potential economic benefits. Efficient use of draglines requires a thorough knowledge of the powered functions, the 3D rotational and translational motions and machine-formation interactions within the operating environment. Dragline kinematics and dynamics are required to understand and characterize machine performance and efficiency. In order to sustain the high productivity in difficult operating conditions, the dynamics of the dragline must be modeled and analyzed based on comprehensive kinematics. This paper investigates the planar kinematics of the front-end assembly and its interactions with the formation during excavation using the “Vector Loop Analysis” formulation with comprehensive simulation modeling in MATLAB Simulink. The kinematic models are used to examine the translational, rotational and angular displacement, velocity and acceleration components of the dragline front-end assembly along defined bucket trajectories during excavation. The results are the precursors for comprehensive modeling to examine the load deformation, torque requirements and dragline stress loading profiles for improving machine health and longevity.

Jan 1, 2006

By F. T. Paleari, J. A. Finch

Radial gas holdup profiles were measured in a 50-cm-diam, 400-cm-high flotation column using a multi-cell-conductivity probe. Three bubble-generation systems, including a system with up to eight vertical filter-cloth spargers, a system with three horizontal filter-cloth spargers and a system with three (horizontal) Cominco-type spargers, were examined. The variables investigated were the number of spargers, the symmetry of their arrangement and the height above the spargers. Batch water containing up to 20 ppm frother was used. Generally, the profiles tended to be uniform (flat) with some profiles exhibiting a slight "wavy" pattern. The vertical sparger arrangement proved to be the most difficult in which to achieve a profile symmetry. The horizontal spargers gave uniform profiles at right angles to their length but gave decreasing gas holdup along their length. The Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers to simulate a malfunction did not produce strong asymmetry in the profiles.

Jan 1, 1995

As discussed previously, total cost is the sum of the direct materials, direct labor, and production overhead costs. The assignment of direct materials and direct labor costs to individual activities is generally straightforward. The assignment of overhead often is not. Overhead costs frequently contain allocations that only approximate the demand the activity has made o; the overhead resources. The inaccuracy of the overhead calculation can create erroneous production cost information and lead to suboptimal management of the operation. This problem is particularly acute when determining the production cost of individual products in multiproduct firms. Pricing, process management, and product mix decisions are especially susceptible to errors in product costing. The problem of properly determining production cost is complicated by the fact that few if any alternative methods exist to identify the inaccuracies in overhead allocation. To avoid errors, some firms simply ignore overhead costs in their product cost calculations, particularly those resulting from marketing and distribution of the final product.

Jan 1, 1999

By Charles C. Y. Chen, Duane R. Skidmore

Batch leaching of Ohio #1, Ohio #4A and Ohio #5 coals was conducted with the thermophilic. sulfur, oxidizing microorganism: Sulfolobus acidocaldarius. Four different size fractions of each coal, with median sizes of 508, 200, 90, and 49 microns, were subjected for 10 days to leaching in a 5% coal-water slurry at 72°C and a pH of 2. Release rates and extent of sulfate and iron I1 and I11 ions from the coals during the leaching process and distribution of sulfur forms (sulfate, pyritic and organic) in the coal samples before and after treatment were determined. Data indicated that Ohio #1 coal, with an initial sulfur content of 0.6%, showed no significant changes with leaching in total sulfur content or forms of sulfur. The Ohio #4A coal, with initial total sulfur content near 5%, yielded product, for sizes below 200 microns with 90% reduction of pyritic sulfur while the extent of organic sulfur removal varied with coal particle size. Results similar to those for Ohio #4A were observed on the Ohio #5 coal, which had an initial total sulfur content of 3% and a final sulfur content near 1%. The findings were interpreted in terms of basic biological, chemical and physical mechanisms.

Jan 1, 1989

By Frank X. Bellini, Marc Saidman, Allen J. Hulshizer, Anthony J. Stewart

The cooling water system for the Seabrook Nuclear Station involves 10.25 Km (33,623 ft.) of 6.7 m (22 ft.) OD hard rock tunnels, over one third of which is under and terminating over 1.6 Km (a mile) out in the Atlantic Ocean. The major excavation is accomplished by two TBM's concurrently driving the intake and discharge tunnels which by mid-January, 1981, completed 92% of the excavation. This paper presents the case history of the excavation work and describes a computer program developed to evaluate major activities of TBM excavation on a shift-by-shift basis. Details and summaries of the production efforts are computer plotted in different forms to facilitate the evaluation of production performance, trouble spots and trends.

Jan 1, 1981

By K. S. E. Forssberg, K. Hanumantha Roa

Batch flotation tests are carried out with phosphatic material from LKAB, Sweden containing carbonatic and siliceous gangue while using sodium oleate as collector and sodium silicate as modifier. The pulp liquid is analysed for oleate, silicate, carbon dioxide, calcium, magnesium and phosphorous after each flotation test under different reagent conditions and flotation pH. Theoretical calculations of thermodynamic chemical equilibria in apatite-calcite-sodium oleate-sodium silicate system have been carried out with the help of SOLGASWATER computer program. During the calculations, the chemical variables are maintained similar to the operating chemical variables in flotation. A comparision between the experimental and theoretical chemical equilibria has been made and the flotation behaviour of apatite is discussed with reference to the theoretically calculated pulp model.

Jan 1, 1993

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003