Search Documents

By Staff

Assembling consistent data for a 40-year time series is a challenge because of the many changes that have occurred in this period. In many cases, because of process improvements and consumer requirements, grades of materials change in a 40-year span. This can lead to a wide fluctuation in price data simply because of increased costs for premium grades. Sources for obtaining price data can also change during a 40-year period. Changing the data source also introduces anomalies in a time series. In some cases, published price data are not representative of the real value of the material and provide little basis for further analysis. For some industrial mineral commodities, there are only a few producers, and value and production data are considered proprietary. In the data presented in this chapter, every attempt was made to ensure that the data were as consistent and representative of the industry as possible. However, the factors mentioned above may have introduced inconsistencies in some of the data series. Many different factors influence trends for industrial minerals because of the diversity of end uses for these commodities. Trends in production and prices for most of the industrial minerals can be related to one or more of the following: changing demand or technologies in end-use industries, development of new end uses, the effect of environmental regulations, production and processing technology changes, energy costs, foreign competition and substitution by other materials, and production as a byproduct of other minerals. World economic conditions, such as recessions and inflation rates, also play a part in some production and price trends. Data for 40 years of production for industrial minerals in the United States are presented in [Table 1] in 10-year increments. Unit values for the industrial minerals, in actual and constant 1990 dollars, are shown in [Tables 2 and 3].

Jan 1, 1994

Stope width was controlled around 3.5 feet for the narrow high grade vein system at Hollister Gold Mine. Without top access, backfill material was pumped from bottom access up into stope through a series of pipes after ore had been slushed out in each mining cycle. Backfill material was changed from one layer of low strength concrete plus one layer of high strength concrete cap to one layer of low strength cellular concrete plus one layer of high strength concrete cap. Backfill cost was cut down to 30 percent during this process. To reduce the steel concrete pipe set up and tear down time which was about 2 to 3 shifts in each mining cycle, steel pipes were left in man-way between mining cycles. Cellular concrete was firstly introduced into backfilling stopes at Hollister mine in Nevada Mining. This process including concrete pump selection, pumping pipe selection, material mixing, material mechanics and quality control were fully covered in this paper. CUT AND FILL MINING CYCLE The most flexible mining method, cut and fill (Figure 1), was used to mine the high grade, narrow steep vein system on this Northern Nevada property which is located eighty miles north east of Winnemucca. Without top access, stopes were accessed through two man-ways on each end, in which people travel ladders and material transport slides were set up (Figure 2). Each mining cycle was called a cut, from 6 to 8 feet high. Overhand sequence was used. Mining cycle started with drill and blast the middle portion of the stope, then expanded towards both ends. Broken ore was slushed into mill hole located at middle of the stope and then mucked out through bottom access into main haulage. Stope length was about 300 feet, which was restricted by slushing distance. Timber man-ways and mill hole would be raised and established for backfill and ready for the next mining cycle.

Jan 1, 2011

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By Brian Flintoff

SCOTT COULTER: Our second speaker today is Brian Flintoff. Brian graduated from the University of Alberta in 1973 with a master's of science degree and worked as a project metallurgist at Brenda Mines until 1977. He returned to the University of Alberta in late 1977 to work on his Ph.D. and later joined the faculty of engineering in 1980, leaving in 1988 to rejoin Brenda in the newly formed process technology division. In 1998 he left Svedala-Brenda to take a position with Simons International's newly formed enterprise development services group. His topic today is "People: Reduce, Reuse, and Recycle." INTRODUCTION BRIAN FLINTOFF: Historically, the mining industry has relied on the people within a corporation to get things done. The culture of most companies was one of a slow but sure development of people, processes, equipment, and technology. Many of the larger companies supported in-house engineering and research organizations. However, the metal market pressures of the 1980s and the emergence of the global economy in the late '80s and early '90s put enormous financial pressures on the industry. As the old adage says, "necessity is the mother of invention," and the mining industry, like many others, has undergone a transformation. A cornerstone element of the transformation was the downsizing (or right-sizing) that was calculated to "trim the fat" from the capital and operating budgets. The goal was and is to find the highest sustainable operating profit.' While I'm sure one can find examples of losers (e.g., those who can be classified as suffering from corporate anorexia or institutional Alzheimer's) in such business reengineering efforts, there is little doubt that, on the whole, the transformation has been successful. The reality that now faces mill management is "How to do more with less?" At the risk of oversimplifying, one can look at this on two levels:

Jan 1, 1998

By Randolph E. Scheffel, David C. Fitch, David K. Hogan, Mark R. Welsh

In Oct. 1981, Ranchers Exploration and Development Corp. began producing silver bullion from the Escalante mine and mill complex, located in southwestern Utah. Current in-place reserves are estimated at 2.42 Mt (2.67 million st) of ore, containing about 936 t (33 million oz) of silver at an average grade of 428.5 g/t (12.5 oz/st). The vein-type deposit is being mined underground through a decline that is currently 864 m (2,835 ft) in length, but will ultimately be at least 1.5 km (5,100 ft) long. The mine is completely mechanized with rubber-tired equipment, and is producing 680 t/d (750 stpd) of ore, five days a week, or 177 kt/a (195,000 stpy). Additional capacity is available. The cyanide leach mill and associated refinery are presently producing 4.35 t/month (140,000 oz/month) of silver bullion-an an¬nual rate of about 52.25 t (1.68 million oz). With minor modifications, the mill can produce up to about 70 t/a (2.25 million oz/year), and expansion is currently underway. History The Escalante property is located 68 km (42 miles) west of Cedar City, UT, on the west side of the Escalante Valley, where the vein forms a gentle ridge in an area of low, rolling hills. For years, the vein has been the object of considerable exploration, but never became more than a sporadic producer, primarily due to low silver prices. Heber Holt of Enterprise, UT, staked the original four claims in 1896; they were patented in 1910. During the next 48 years, limited exploration and mining activity was conducted on the property. Systematic evaluation and development did not, however, begin until March 1958, when Samuel S. Arentz, a prominent mining engineer and consultant, formed several joint ventures with mining and oil companies that conducted drilling, drifting, mining, and water drawdown tests on the property. However, it remained uneconomic, principally because of low silver prices and costs for pumping large flows of underground water. In 1975, Ranchers obtained an option on the property and in 1979 began a drilling program. As of May 1982, the company had drilled 70 core holes, bringing the number of exploratory holes drilled on the property to 138. Test mining began in 1979 as silver prices increased, and full mine development began in 1980. Mill construction began in Sept. 1980, and on Aug 29, 1981, the first ore was fed to the mill.

Jan 9, 1982

By S. Bhagwat

Coals capable of emitting 2 lbs SO2/106 Btu heat input must be defined as high sulfur coals. This is because electric utility plants built after 1971 may not emit more than 1.2 lbs SO2, and those built before 1971, and regulated under the State Implementation Plans (SIP), may exceed the 2 lbs S0 limit only under closely defined restrictions concerning ambient air quality and prevention of air quality deterioration. Coals produced in Kentucky, Illinois, West Virginia, Ohio, Pennsylvania, and Indiana account for 77% of SO2 pollution potential and are, therefore, the subject of this investigation. These coals have suffered market share losses in the 10 years from 1974 through 1984. This is due to their sulfur content as well as their lack of price competitiveness with low sulfur western and imported coals. Kentucky and West Virginia have been able to increase their compliance quality coal production substantially, but other states have largely been unable to do so because of nonavailability of low sulfur coal deposits. Assuming that the current relative productivity and cost competitiveness of coal producing states will not change significantly by 1994, this paper makes two projections of coal production in the selected states. In scenario I, the current clean air regulations are assumed to apply until 1994, and coal production in the selected states is projected to in¬crease by about 6% in 1994 compared to 1984. In scenario II, it is assumed that acid rain legislation will be implemented, which will adversely affect the markets for high sulfur coals. Coal production in the selected states under this scenario is projected to decline about 10% between 1984 and 1994, jeopardizing up to 13,000 mining jobs. The author concludes that better coal quality and greater cost competitiveness are both essential to stem the market losses and to regain strength.

Jan 1, 1988

By Bruce K. Cantrell

As part of a continuing study of diesel exhaust aerosol characteristics, the Bureau of Mines has applied Chemical Mass Balance (CMB) model source apportionment analysis to evaluate a size selective sampling method for determining the separate diesel exhaust and coal dust aerosol concentrations in a diesel equipped coal mine. Size selective sampling was used under the premise that diesel exhaust aerosol dominates the submicrometer aerosol size range, while most of the mineral dust aerosol is greater than 1 m. A micro-orifice, uniform deposit impactor (MOUDI) was used as the size selective sampling method. Concurrent samples of mine aerosol were collected using a dichotomous, respirable aerosol sampler. This sampler separated the fine and coarse size portions of its sample at 0.7 m. Trace element concentrations for in-mine aerosol sources and the dichotomous samples used by the CMB model were measured using Instrumental Neutron Activation Analysis. The CMB analysis, applied to both the fine and coarse fractions of the respirable mine aerosol, yielded the mass concentration contributed to each by diesel exhaust and mineral dust aerosol sources. The MOUDI size distribution data were analyzed using nonlinear regression to parameterize the fine and coarse fractions of the sampled aerosol and to estimate the contributions to each fraction from both coal dust and diesel aero- sol sources. For the diesel mine visited, analysis of the MOUDI samples yielded a value for the fraction of the fine aerosol attributable to coal dust of 15[]7% fine fraction coal from analysis of the MOUDI samples versus 25[]4% from the CMB analysis. The remainder of the fine aerosol in the mine was diesel exhaust aerosol. CMB analysis confirms the original premise for such sampling. After correcting for the presence of coal dust in the fine aerosol fraction, analysis of the MOUDI size distributions yielded estimates of respirable mineral and diesel exhaust aerosol concentrations that were accurate to with-in 10% of values determined by the CMB apportionment.

Jan 1, 1987

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

The Mine Safety and Health Administration (MSHA) academy in Beckley, WV, received enquiries from various segments of the mining industry concerning alcohol and substance abuse in the mining industry. The MSHA Director formed a committee, the Mining Industry Committee on Substance Abuse (MICSA), to deal with these enquiries. The committee met in April 1985 at the mining academy in Beckley. The MICSA committee expanded its membership to represent labor, management, and government agencies affiliated with the mining industry as well as government agencies dealing with alcohol and drug abuse. This expanded 18-member committee met for the first time in July 1985. At that time, two cochairmen were elected, one from labor and one from management. MICSA has spent time on education by sharing information on the issues and by calling in outside experts for advice and consultation. The committee also initiated several projects. These include a resource manual on substance abuse and employee assistance programs. Mine operators and labor unions can use these programs as guides. MICSA is also assembling statistics on substance abuse, particularly as applied to mining. And the committee commissioned an Education film, Substance Abuse, Is It Our Problem? (The results of a survey on drug use, given in Table 1, suggest that substance abuse may indeed be a problem.) The educational film, produced by MSHA, is an introduction to the problem of substance abuse in the mining environment. The film encourages mine operators, labor unions, and miners to analyze their individual circumstances to determine whether a problem exists. The film also offers ways to deal with the problem. And the film invites the mining industry to request additional information from MICSA. There is no single approach to substance abuse that will fit the need of every mining operation. As with any health, safety, or production problem, remedies must be site specific. MICSA's aim is to channel ideas to those who seek to help employees in a mining environment who seek to rid themselves of alcohol and substance abuse. As stated more formally: The Mining Industry Committee on Substance Abuse represents the efforts of labor, management, and government. The mission of the committee is to make the mining industry aware of the problems resulting from alcohol and other drug abuse and to recommend possible methods to remedy the problem. The function of the committee is to assist the industry in developing programs and resources to recognize and provide help for troubled employees, and thus reduce the risk of accidents, while lower absenteeism and increasing productivity.

Jan 11, 1987

By Bernhard C. Koch, Richard W. Hutchinson, Bernhard Free

The Tertiary Silverton caldera collapsed asymmetrically to the southwest 27.5 m.y. ago. Resurgent volcanic activity is expressed by a quartz-monzonite stock at the southern caldera margin and by the Red Mountain porphyry stock in the northwest of the caldera which were emplaced at 25 m.y. and 11 m.y. b.p., respectively. The apical Eureka graben formed between 27.5-22.5 m.y. ago and transects the Silverton caldera southwestward. In the northeast it terminates at the 22.5 m.y. Lake City caldera margin. This graben as well as caldera faults provide dominant structural control for base and precious metal deposits. The epithermal gold mineralization of the Gold King mine is proximal to the Red Mountain stock in the north central part of the caldera. Here, west-northwest striking faults related to the collapse of the caldera intersect northeast faults of the Eureka graben. Superimposed upon earlier base metal mineralization at 23 to 22.5 m.y. b.p., the 11 m.y. younger gold metallization was a distinct event at Gold King. Supergene enrichment of the hypogene precious metal assemblage resulted in a metal tenor of up to 3,016 g/t gold and 1,088 g/t silver. The deposit is hosted by quartz-latite tuffs, flows, and flow breccias of the Burns Formation. Veins, up to 5 m wide follow steeply southeast and northwest dipping structures of the Eureka graben. Subsidiary veins up to 2 m wide branch off the main lode and are termed "flat veins" because of their conformable strike but shallow dip of 45' to 50' toward the northwest. Meteoric water-dominated hydrothermal solutions generated by the Red Mountain stock ascended through intensely fractured, ferruginous

Jan 1, 1988

By E. M. - Technical Papers Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the dis- abling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety

Jan 1, 1987

By Robert S. Ondrey, Robert A. Haney, Kenneth G. Fields

As part of an MSHA program to assess the effectiveness of dust control parameters for longwall mining operations, respirable dust studies were conducted on six longwall sections. The purpose of these studies was to evaluate the influence of airflow and production on longwall dust control. The sections were sampled for 3 to 35 shifts. In addition to dust, ventilation and production measurements, other dust control and operational parameters were measured. The water spray system at each operation conformed with generally recommended practices. Therefore, improvements to the dust control system would be most appropriately achieved through improvements to ventilation along the face. Two methods of assessing the influence of ventilation and production were used. For two of the six mines where extensive sampling (22 and 35 shifts) was conducted, multiple linear regressions were used to relate the dust concentration versus airflow and production data. For these two mines, statistically significant correlations existed between concentration and both production and airflow. The multiple regressions fit to the data indicated that for every 0.47 m3/s (1,000 cfm) increase in airflow, there would be approximately 0.04 to 0.07 mg/m3 reduction in dust concentration; and, for every 1,000 ton increase in production, there would be approximately 0.15 to 0.50 mg/m3 increase in dust concentration. For the four mines with limited data (3 to 10 shifts), as well as for the two mines with extensive sampling, an average ratio of airflow per ton of coal mined was calculated by proportioning the airflow to production and the designated occupation personal respirable dust exposure to a 2.0 mg/m3 concentration. The airflow-to-tons ratio required to maintain a 2.0 mg/m3 dust concentration ranged from 0.0038 0.0071 m3/s per ton (8 to 15 cfm/ton). Both of these data treatments were used to calculate airflow requirements based on normal production rates. For the two mines where both the regression and airflow-to-tons ratio were calculated, results from the two methods agreed within 25 percent.

Jan 1, 1993

By V. Castranova, L. Wu, K. Van Dyke, J. Gutierrez, V. Vallayathan

Since it has been demonstrated that silica caused phagocytic cells to activate lipoxygenase metabolism of unsaturated fatty acids we thought selective inhibition of this metabolic pathway might be helpful in treatment of silicosis. It is known that lipoxygenase metabolism plays a role in the pathogenesis of a variety of inflammatory and hypersensitivity conditions. Further, it is believed that the alveolar phagocytic cells which engulf silica begin the inflammatory cycle which produces the metabolic products, cytokines and growth factors which causes fibrosis in the lung. There have been indications that drugs which inhibit lipoxygenase can inhibit fibrosis from other causes. Previously, we developed a method which detects the activity of lipoxygenase metabolism by measuring free radical oxidation via light production or chemiluminescence (CL). We decided to apply this method to phagocytic cells that would be found in the lung in the presence of silica with and without newly developed inhibitors of the lipoxygenase reaction. We used drugs which inhibit lipoxygenase directly including AA861 (TAKEDA), A63162 (Abbott), and an inhibitor that scavenges free radicals produced from the lipoxygenase reaction, nordihydroguairetic acid. In addition we used an indirect inhibitor, tetrandrine. We found drug inhibition of silica activated CL from alveolar macrophages, neutrophils and human leukemia (HL-60) cells differentiated with DMSO. Nordihydroguairetic acid 2x10-5M produced almost complete inhibition in all three cell types. In human leukemia cells (HL-60) A63162 and tetrandrine were equally inhibitory at 42% while in human neutrophils A63162 and tetrandrine were less active 22 and 10% respectively. In macrophages A63162 and AA861 were less than 50% inhibitory to cellular CL at 2xl0-5M. Direct assay of tetrandrine (2x10-5M) with sodium arachidonate and soybean lipoxygenase reveals no inhibition. All antilipoxygenase drugs regardless of mechanism were inhibitory to cellular chemiluminescence from all three types of phagocytic cells. These drugs alone or in mixtures could prove useful in treatment of silicosis.

Jan 1, 1991

By Sriram Padmanabhan, Jan M. Mutmansky

The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Utah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7. The results will be presented using two categories of data collected during two separate phases of the research: (1) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and (2) quartz concentration data from mines chosen at random. The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent.

Jan 1, 1989

By Donald A. Dahlstrom

INTRODUCTION Solid-liquid separation is an important and many times a critical step (or steps) in a mineral or coal processing plant. Some examples of typical critical separations are as follows: 1. Operating a seven to eight stage CCD thickening circuit to re¬cover almost all of the caustic and alumina trihydrate values in an alumina plant. This must be accomplished with highly scaling slurries, starting temperatures of over 100°C and operate on a closed circuit system. 2. Making a filter step operate to produce a proper moisture for the balling step so that the pellet furnace can produce a proper product. Bentonite addition must be minimized and a good quality filtrate must be maintained to prevent abrasion of the internal parts of the filter. 3. Operating a closed water system in a coal washing plant so that reclaimed water containing less than one percent suspended solids is produced for reuse to maintain beneficiation ef¬ficiency. Refuse solids must also be thickened so that they can be effectively dewatered to meet state disposal requirements. 4. Recovering phosphoric acid values from a slurry containing gypsum and other gangue solids at an elevated temperature. This must be done while minimizing wash water and maximizing P2O5 re¬covery while simultaneously minimizing scale problems. While solid-liquid separations are important to overall performance in the processing plant flowsheet, it is also a significant factor in plant costs. Capital and operating costs for all the solid-liquid separation steps (includ¬ing water reclamation for reuse) in such plants are probably between 10 and 20%. Energy consumption can also be important in these separations. For example, in the copper concentrator, it is the third largest category in energy consumption, after comminution and flotation. Obviously, solid-liquid separation steps in a plant demand proper atten¬tion in design in order to achieve both optimum performance and cost. Simultaneously, knowledge of funda¬mentals are important to improve results in existing plants.

Jan 1, 1986

By T. M. Karppanen

Shotcrete is used both in mining and tunnelling for supporting rock. Both dry and wet processes are used for shotcreting, and each produces good quality concrete. Thick shotcrete layers function as a concrete arch supporting loose rock. Thin layers prevent relative movements between the blocks of rock due to the fine concrete in the cracks and joints. No progressive fallouts occur since key blocks are kept in place. Rockbolts are often used together with shotcrete in order to create an arch around the tunnel making the rock to support itself. Shotcrete is sprayed either manually or by means of mechanized equipment. The aim is to spray required the layer thickness in one pass and with a minimum amount of rebound. Sprayed layers should also be as even as possible. The tip of the nozzle should be moved in circular movements. The shotcrete should be sprayed at a right angle to the rock surface; the optimum distance from the nozzle to the application surface must be found by experiment. In a mine shotcreting forms a materials handling system which includes batching, transporting and the actual shotcreting. The equipment used vary depending on the spraying method, mining conditions and the location of the mine. Shotcreting is performed with a purpose-designed unit in most cases where operation is mechanized. The shotcreting unit consists of a spraying machine with a hose and a nozzle, an additive system, a manipulator and a mobile carrier with all the necessary controls and accessories. The key element of the unit is the shotcreting manipulator which holds and guides the nozzle as required. The manipulators currently in use are hydraulically operated, and their remote controlled booms are also often called robots. These manipulators have enabled users to increase their output capacities, to remove the operator away from unsafe areas and from the influence of dust and rebound. Furthermore, they improve the shotcrete quality and reduce shotcreting costs.

Jan 1, 1989

By Charles U. Keranen

The Tilden Mine is an iron ore mining, processing and pelletizing facility located on the Marquette Iron Range in Michigan's Upper Peninsula. It has a designed capacity to produce 8 million long tons of pellets annually from 21 million long tons of crude. It is a partnership owned by The Cleveland-Cliffs Iron Company, Algoma Steel Corporation, LTV Steel Corporation, the Steel Company of Canada, Wheeling Pitts- burgh Steel Corporation and the Sharon Steel Corporation. Cleveland- Cliffs manages and operates the Tilden. The crude ore averages 35% iron and is primarily non-magnetic iron oxide and silica. The major ore mineral is martite. Hematite, earthy hematite, goethite and magnetite are also present. The principal gangue mineral is chert. The ore grains are mostly in the 10 to 25 micron size range which necessitates very fine grinding for liberation. The concentrating process is the most complex one used in the iron ore industry. The unique technology for Tilden was developed in the mid and late 60's. The design and construction occurred in the early 70's and operation of the first phase which was of 4 MLTPY capacity began in October. 1974. Expansion of the facility to the current 8 MLTPY capacity was completed in 1979. Chemicals are the key to the beneficiation process at the Tilden Mine. The flowsheet utilizes selective flocculation - desliming, cationic silica flotation and concentrate dewatering by thickening and filtering. Nine different process chemcals are used. The control of the reagent feed systems is highly auto- mated. The entire concentrator is operated from a central control room. The concentrator flow diagram is presented in figure 1. The plant consists of 12 primary autogenous grinding lines, a common crushing circuit to handle an intermediate product within the primary grinding section, 24 pebble mill lines with cyclones and deslime thickeners, 12 flotation lines, 4 concentrate thickeners and slurry tanks, 8 lines of filters with six machines per line, and 2 tailings thickeners. A pumping system was installed in 1980 to permit the direct return of tailings thickener overflow water back to the reuse water pumphouse.

Jan 1, 1986

By R. P. King

INTRODUCTION It is now 21 years since Wiegel and Li published their paper on a random version of Gaudin's model for the mineral liberation phenomenon (Wiegel and Li, 1967). This paper was to revitalise interest in North America in one of the most fascinating, difficult and important problems in the field of theoretical mineral processing. Gaudin had many years previously (Gaudin, 1939) already presented a penetrating analysis of the problem and Wiegel and Li based their analysis very closely on the Gaudin model but they realised that the indeterminate geometrical structure of mineralogical materials demanded that only probabilistic models could provide the necessary quantitative information when working with real materials. They proposed and solved a randomised version of the Gaudin model but retained the essential geometrical simplicity of cubic mineral grains and a cubic fracture pattern. Although their model met with some limited success it was to be superseded in due course. During the 1940's and 1950's the classical field of geometrical probability spawned the mathematical discipline of integral geometry and as early as 1965, Bodziony (1965, a,b) showed that the techniques of integral geometry could accommodate the problems associated with the indeterminate nature of the geometrical mineralogical structure, provided that these were couched in probabilistic terms. In particular he showed that the quantitative description of the comminution process and that of liberation could be decoupled with the resulting economy of effort. This idea has profoundly influenced the course of research in liberation theory and has greatly facilitated its application and the measurement of liberation in a practical way. Bodziony demonstrated also that any theory that required the specification of the mineral "grain

Jan 1, 1989

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

By Alena Conrads, Markus König, Markus Scheffer, Markus Thewes, Hannah Mattern

"INTRODUCTION In recent years, the development of tunnel boring machines has revolutionized the tunneling industry. The general structure of a tunnel boring machine (TBM) can be described as a multi-component system. To achieve high performance rates, machine elements have to perform reliably. Performance losses and interruptions of the construction process should be prevented or at least, reduced to a minimum. In order to achieve high advancing rates, cutting tools must be in good condition at any time. Furthermore, failure of individual tools might result in increased and faster wear of remaining structural components. For this reason, maintaining and replacing cutting tools is crucial to prevent project delays due to insufficient boring performance. Precise prognoses concerning the prevailing geology are infeasible and thus, efficient scheduling of maintenance actions is challenging. The intention of this work is to analyze different approaches of TBM maintenance in soft ground. Different strategies are analyzed by the use of a simulation approach. Cutting tool condition is regarded as performance limiting factor. The maximum operation time of the cutting tools is determined using the “Soil Abrasivity Index”. A case study serves to show the effects of different maintenance strategies on total project duration. SCHEDULING OF MAINTENANCE ACTIONS Scheduling maintenance actions of single and multi-component systems concerns numerous fields of industrial production. Concentrating on mechanized tunneling in soft ground, cutting tool maintenance represents the most common reason for intermission of advance (Köppl 2014). In literature, time-based and condition-based maintaining techniques are widely discussed. The following section outlines the principles of time- and condition-based policies. Furthermore, examples for their applications in recent research are given. Time-Based Maintenance In general, the time-based maintenance approach assumes that the failure behavior of the system components is predictable. Maintenance actions are scheduled according to predefined intervals (e.g., hours, days, weeks). A detailed analysis of preventive repair times or interval forms the basis for maintenance decisions. For this approach, an adequate quantity and quality of data is fundamental. Numerous studies deal with the analysis of time-based maintenance for production equipment. In fields of mechanized tunneling, unplanned machine downtimes restrict the applicability of time-based maintenance approaches. Thus, this paper mainly focuses on condition-based maintenance."

Jan 1, 2016