Search Documents

By George R. Powe

If Campbell County, Wyoming were an independent nation, it would rank fifth in the world among countries with known coal reserves. Only the United States, Russia, mainland China and West Germany would have greater volumes available. Not too many years ago that statement would not have seemed important, because oil and natural gas had become our nation's principal fuels. Western coal deposits, particularly those of the Powder River Basin in Montana and Wyoming, and which underlie virtually all of Campbell County, were largely unknown. But recently, in response to the three-pronged stimulus of vanishing gas reserves, rising petroleum prices, and clean environment statutes, these vast deposits have been delineated and have become, in the minds of many, indispensable to our goal of energy independence. Not only does western coal lie in thick seams near the surface where it can be mined in huge quantities at low cost, but also it possesses another coveted attribute in this age of environmentalism: low sulfur content. At Burlington Northern we count ourselves at the forefront of those who believe this coal is essential to any hope for the government's "Project Independence." But to that belief we add another article of faith. We are convinced the economics of unit train delivery of this incredibly immense resource make it the only transportation system that can help us achieve energy self-sufficiency in this country.

Jan 1, 1975

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By Yadong Xue, Fei Wang, Hongwei Huang, Yan Sun

"Increasing attention to subway tunnel maintenance is being paid with the high speed development of urban rail transit system in China. A novel moving tunnel inspection equipment based on machine vision is developed in this paper. High resolution image acquisition system is proposed for tunnel crack and leakage inspection. The main components of this image acquisition system includes high speed CCD cameras, linear lights and high performance computer. To inspect the crack less than 0.3mm with a 3-5km/h speed in subway tunnel, we need to consider resolution and line rate of camera, pixels of cameras, range of inspection and illumination intensity of lights simultaneously. The optimization design is proposed to make the equipment more convenient for tunnel use. Entire tunnel situation can be detected and recorded in a single inspection process. This equipment has already been verified in Shanghai subway tunnel for defects inspection.1. INTRODUCTION In China, the quantity of subway tunnel has reached a large scale in recent years. Until 2014, there had been more than 2300km of subway tunnel in China which accounted for nearly three quarters of Chinese urban railway system (Zhang Chen,2015). In some metropolises like Beijing and Shanghai, most of the metro tunnels has already run over 20 years which within maintenance phase. This has brought about plenty of inspection work and maintenance work to guarantee the tunnel under the serviceability limit states. The increase of running mileage of subway tunnels in China has been displayed in Fig 1."

Jan 1, 2016

By Erich U. Petersen

Chemical zoning studies of mineralization can be useful in guiding exploration efforts. They permit one to determine the limits of mineralization and to correlate mineralized intervals in drill holes. Fahlore minerals are well suited for zoning studies because they are common minerals found in a variety of deposits, exhibit chemical diversity, and record the chemical evolution of migrating hydrothermal fluids. Zoning information in the form of metal ratios preserved in fahlore minerals was used to determine ore body limits in the Orcopampa precious metal system, Peru, and to correlate between multiple ore horizons in a sediment hosted massive sulfide (SHMS) currently under investigation. The current generations of electron microprobes provide the most efficient, accurate and economic way to analyze the tens to hundreds of sample required to successfully describe and use zoning information at the mine scale.

Jan 1, 1991

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By Donald G. Dahle

Project Payette is a conceptual nuclear experiment under the Vela Uniform program intended to further evaluate the mechanism of seismic decoupling. Vela Uniform is a Department of Defense program to improve this country's capability to detect, locate and identify underground nuclear detonations. This program evolved from recommendations of the Panel on Seismic Improve¬ment, (Berkner Panel), an officially appointed group of noted U. S. scientists. This Panel, taking note of difficulties in detecting the differences between some underground nuclear detonations and some earthquakes recommended a program of increased basic research in seismology. The theory of decoupling, Which involves possible reducing of seismic motion resulting from underground explosions by reducing the coupling or physical linkage between the explosion and the geologic environment, was investigated by Dr. Albert latter and his associates at RAND during the late 1950's. The concept has been further investigated theoretically by scientists of the Lawrence Radiation Laboratory and the Sandia Laboratory. The theory has been tested experimentally under Vela Uniform Projects Cowboy, Dribble and Sterling. The Salmon Event of Project Dribble was a tamped (with the explosive in firm contact with the geologic formation) nuclear detonation 2700 feet below ground in the Tatum Salt Dome. Project Payette, if found to be feasible and if authorized for actual execution, would become a decoupled experiment in the same environment.

Jan 1, 1968

By R. Kingman

At Tahawus, New York, National Lead Company operates the MacIntyre Development, This operation produces 10,600 long tons of ore per day for crushing, 8,000 tons for grinding and processing, of which 2,000 tons per day reports as tailing for disposal in an impounded tailing storage area. With the change in location of mining operations at the mine of National Lead Company, a change in the area for tailing disposal by gravity became necessary, This called for the diversion of tailing from near the proposed mining area to areas more favorable for long term storage by gravity. In order to avail the operation of maximum storage for the future, a uniform minimum grade launder was proposed with a minimum velocity and maximum outfall at the discharge. Disposal of the gravity and flotation tailing was formerly accomplished in open ditch from the concentrator at a grade of 1.5 percent. It was desirable to design the new launder at grades less than this for the greater storage elevation.

Jan 1, 1966

By James R. Yancik

Economical and environmental pressures necessitates the recovery of the minus 0.6 mm x 0 coal generated by todays mining machines. This size fraction, dependent on the type of production unit, maintenance of the production unit, and the Hardgrove Grindability Index, can be a substantial portion of the Preparation Plant feed. Historically, dewatering of the collected 0.6 mm x 0 product has often been rather expensive and marginal with respect to surface moisture reduction. The Freeman United Crown II Preparation Plant more than adequately demonstrates that the continuous scroll type centrifuge can dewater 0.6 mm x 0 coal to acceptable surface moisture levels.

Jan 1, 1981

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By Christophe Bragard, Jason Choi, William H. Hansmire

This case history provides a physical benchmark of tunneling technology progress comparing an old hand-mined tunnel to a modern 20-ft-diameter EPB TBM that mined in the same ground. This rare opportunity to see how tunnels were constructed many years ago occurred when an old 10-ft-diameter storm drain tunnel in the way of os Angeles subway construction was demolished and replaced with obas berglass pipe. Steel rib and lagging initial support was exposed showing solid-sawn 2" × 12" × 48" redwood lagging. This paper documents the as-built old tunnel, how it was successfully replaced, and some lessons learned.

Jun 23, 2024

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024

By Juan L. Yarmuch, Hyam Rubinstein

Open-pit mine planning is a key process in the definition of mineral reserves and their efficient removal. Ore in open-pit mines is extracted bymining sequential pits called pushbacks. Pushbacks need to satisfy complex geometrical constraints to ensure the efficient usage of equipment. To date, no algorithms that both account for those constraints and maximizeNPV, are commercially available. Therefore, pushback design is done by engineers relying on their expertise to incorporate practical features intothe output of commercial tools. In this article, we present a new algorithm that produces close to optimal practical pushbacks and we illustrate its performance in real mines.

Jun 25, 2023

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By Jodi Banta

In an effort to reverse the trend of declining enrollments to mining engineering programs that began in 2015, the University of Arizona has implemented a number of interventions over the past five years, including ramping up its pre-college mining education and outreach, and undertaking several enrollment research projects. This article is the second of two installments to discuss the results of our latest study. The first part can be found in the September 2025 issue of Mining Engineering magazine. To better understand mining’s competitive position, the School of Mining Engineering and Mineral Resources conducted a comprehensive study to determine: 1. How prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree. 2. Factors affecting students’ choices of degrees and career plans. 3. The roles parents and educators play and how they influence students.

Nov 1, 2025

By D. D. Harbuck

Previous studies at the U.S. Bureau of Hines have shown that only 70 to 80% of the germanium in domestic zinc process residues can be extracted during H2S04 leaching. To increase germanium extraction, the Bureau developed and researched the hypothesis that minor amounts of germanium and zinc silicate, both present in zinc calcine, dissolve during the leaching stages of zinc processing, forming soluble germanium and silica gel. This silica gel then selectively adsorbs germanium from solution, rendering the germanium insoluble. Testing showed that as the amount of silica gel formed increased, the amount of insoluble germanium in the zinc residue increased. Several processing alternatives are presented for overcoming this problem.

Jan 1, 1991

By Neal P. Cochran

The Office of Coal Research Program has been outlined in our Annual Report for a number of years and reported on by various members of the OCR staff as well as by our contractors. The program is national in scope and is intended to develop new and improved uses for our Nation's coal resources and to maintain coal in a favorable economic position, vis-a-vis, the other energy forms. A program has been developed that includes conversion of coal to gas, gasoline and other petroleum-type products, and to electricity. These projects are only one facet of the OCR program albeit an important one. In many of the conversion projects we have underway, original development work has been done with bituminous and sub-bituminous coal. It is the intention of this paper to present a general outline as to how lignite might fit into one or more of these projects as a raw material. Our national lignite reserves are vast in scope and this has been recognized in the OCR program by development of a project specifically for lignite and by including lignite as a test raw material in many other projects. Project Lignite is intended to develop the Cop Acceptor Process for conversion of lignite to a high B.t.u. gas. In this effort we have included the design, construction, and operation of a lignite gasification plant at Rapid City, South Dakota. The work is being conducted by the Consolidation Coal Company and is an outgrowth of their laboratory development of this process. The first portion of our effort included a detailed economic study of a somewhat arbitrary grouping of States designated Market Area A that could be expected to use gas manufactured in a lignite gasification plant. The area included the Dakotas, Minnesota, Nebraska, and Iowa. This geographical area could readily be served if a process could be developed for converting North Dakota's lignite reserves, estimated at 351 billion tons, to high B.t.u. gas. Our study showed that Market Area A had a potential commercial- industrial market of one trillion cubic feet of gas a year. To meet this demand, we believe that part of the load can be obtained from commercial lignite-to-gas plants. At the time of our original study, we concluded that gas could be delivered to the city gate in Market Area A at about 45¢. As a result of price escalation in the interim, our estimate today might be slightly higher, but not significantly so, since some parts of the process appear better today than they did at the time of the original projection.

Jan 1, 1968

By Shawna Von Stockhausen, Hong Yang, Tung T. Vu, Derek Penrice, Kevin Huynh

"The Regional Connector Transit Corridor is a 1.9 mile long light rail transit project in downtown Los Angeles, California. The project includes approximately 4,930 feet of twin bored tunnels together with a mined crossover cavern, 3 deep stations, and other cut-and-cover structures. The bored tunnels will be excavated using an earth pressure balance tunnel boring machine through Fernando Formation (extremely weak to weak rock) and alluvium. The tunneling will be performed in close proximity to a large number of existing structures, including the existing Metro Red Line tunnels with as little as 6 feet of separation. Thus, the evaluations of the tunneling effect on these structures and the instrumentation and monitoring program is an essential part of the project design. This paper provides a very brief overview of the considerations and evaluations of the tunneling effects on the existing structures and results of evaluation obtained during the final design stage of the project. INTRODUCTION The proposed Regional Connector Transit Corridor (RCTC) project provides a 1.9 mile-long connection between the Metro Gold Line from Pasadena and East Los Angeles; and the Metro Blue Line to Long Beach and the Expo Line to Culver City. The alignment is shown in Figure 1. The Regional Connector will provide new tracks through downtown Los Angeles. The project will extend underground from the Metro Blue, Expo, Red, and Purple Lines’ 7th Street/Metro Center Station following Flower Street, curving northeast to the north of 3rd Street under the 2nd Street Tunnel. The alignment will then continue eastward under 2nd Street, turning northeast to cross under the intersection of 1st and Alameda Streets, then splitting into two branches above the ground surface, one branch extending north along Alameda Street and the other extending east along 1st Street. The project elements include 3 deep stations, a SEM cavern, segments of TBM bored tunnels, and cut-and-cover guideway structures. The bored tunnels have an excavated diameter of 20.3 feet. The subsurface conditions along the tunnel alignment generally consist of artificial fill overlaying finer-grained alluvium (dominantly medium dense to dense sandy soils), underlain by coarser-grained alluvium (a wide variety of medium dense to dense sandy and gravely soils). Below the coarser-grained alluvium is Fernando Formation, which is characterized as extremely weak to very weak sedimentary bedrock. A long stretch of the alignment will be excavated in this formation. The soil layers above the Fernando Formation are of variable thickness and spatial distribution. The geologic profile is shown in Figure 2."

Jan 1, 2016

By C. A. Rowland

Comminution efficiency can be expressed in three different ways. Theoretical Efficiency: actual energy consumed, in a comminution machine compared to the theoretical energy required to make the size reduction. Operating Efficiency: compares the operating work index, calculated from production comminution machinery operating data, to the Bond Work Index from bench scale comminution tests or calculated from pilot plant operating data. Economic Efficiency: income compared to planned income. Using the Bond Work Index and operating work index, this paper explains how to determine operating efficiency.

Jan 1, 1998

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996