Search Documents

By W. Pawlos, A. Bakalarz, M. Duchnowska

This paper presents the results of an investigation into the influence of hydrodynamics on a preflotation process for the copper sulfide ore from the Fore-Sudetic Monocline deposits in Poland in a flotation machine. The main aim of the preflotation stage for Polish copper ore is to remove the easy-to-float organic matter — organic carbon — that causes serious problems in metallurgical processes. The organic matter is connected with the presence of shale ore. This paper describes the preflotation experiments conducted to investigate the effect of various stirrer speeds. The upgrading selectivity of copper and organic carbon were analyzed and compared. The results show that the effectiveness of separation between organic carbon and copper decreases with increased stirrer speed in the laboratory flotation machine. The more intensive the mixing of the flotation suspension, the lower the selectivity of the preflotation experiment. Lower stirrer speed probably provides lower mechanical entrainment and flotation of copper minerals.

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

By J. Humphries

With today?s turbulent markets and unprecedented global opportunities, the need to optimize net present value and internal rates of return from capital investments has never been greater. To help address the need, this paper presents an overview of the key processes and strategies for achieving maximum return from capital projects. Best practices discussed address stage gate management for project evaluation, selection, and oversight, project execution efficiency, value improving practices, operational readiness, and operational excellence. The paper also includes a model of key metrics and benchmarking with tips for application. [ ]

Jan 1, 2011

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 4, 1985

By J. M. Hollow, D. E. Walsh, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Carbon fines are collected by a filter press because of their gold value. Samples of the carbon fines show that they consist of 20-30% carbon, 70-80% grit and 0.17-0.68 kg/t (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in a form of recrystallized free gold grains, with the balance being adsorbed gold on the carbon. High recoveries of gold and carbon were obtained in laboratory tests using froth flotation, with a high rejection of the grit.

Jan 1, 2001

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By Klaus Stoss, Bernd Braun

The sinking and lining of a large mine shaft with 8.0 m i.d. and 1,133 m total depth is described in detail. The ground freezing method was applied to safely sink the shaft through unstable, waterbearing strata. Following a brief introduction to the geological and hydrological conditions and the owner's shaft requirements, is the general technical concept to sink and line the shaft. Particular emphasis is put on the lining system which has to provide stability and absolute watertightness for the lifetime of the shaft, even though mining takes place in its immediate proximity. Machinery and equipment used to execute the work are mentioned and commented. Furthermore, the excavation and lining of the large filling stations using rock anchors and shotcrete are described. Details on performance rates are given.

Jan 1, 1983

U.S. Borax’s mine in California’s Mojave Desert is the source of nearly half the world’s supply of refined borates. These minerals are used in hundreds of products, including essential plant nutrients that increase crop yield and quality, and safe building products that protect homes from insects and the elements. Borax’s workforce is also safe. In fact, it is among the safest in the nation. In 2003, the company was recognized by the U.S. Mine, Safety and Health Administration (MSHA) for achieving the best safety record among large U.S. mining operations. It was also recognized by its parent company, Rio Tinto, for achieving the best record among its nearly 80 worldwide mining operations. Borax’s safety performance is five times better than the national average. And its workforce recently achieved more than two million hours without a lost-time injury.

Jan 1, 2004

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

By Sam Ash

The Murray Mine was one of the first mechanized cut-and-fill underground gold operations in northern Nevada. At the end of 2002, mine production began to decline. So the mine entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary in previously condemned areas and in challenging ground conditions. To remain economically viable, new techniques were implemented in operations, geology, engineering and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed the Murray Mine to remain in operation.

Jan 1, 2006

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By B. R. Zernich

Advances in tunneling technology, such as Earth Pressure Balance and Slurry Shield methods, have allowed the tunneling industry to construct tunnels in increasingly difficult ground conditions. In recent years, a number of civil projects including large diameter train tunnels, subway tunnels, water tunnels, sewer tunnels, and combined sewer tunnels have been successfully completed deep beneath the water table in soft ground conditions utilizing modern day Tunnel Boring Machines (TBM). With the increase in difficult ground conditions and higher water pressure comes the inherent need to utilize compressed air to gain access to the TBM?s cutterhead and cutting tools. This paper focuses on one such instance in Los Angeles, CA in which Traylor Brothers Inc. performed a cutterhead intervention by compressing the heading of an 11-foot diameter tunnel to approximately 3 bar gauge pressure. This paper focuses on the environmental controls used to manage ventilation, oxygen levels, temperature, and pressure, as well as discusses the problems associated with toxic gases and the increased risk of fire. The paper will also cover the physical science of the environment and the increased risks of performing basic job functions while in a compressed air heading.

Jan 1, 2009

By Verya Nasri

The Silver Line Phase III Project is the final one mile underground segment of the new Bus Rapid Transit in downtown Boston. The project is expected to significantly reduce existing and anticipated traffic congestion. The twin one-lane tunnels and two station platforms will be built by NATM in Boston saturated soft clay, sand and till layers in proximity to several historical buildings, underpinning two existing cut and cover subway stations and several major utilities in densely built urban area. This paper presents the analysis and design of the NATM tunnels and stations detailing the excavation sequence and support system and various ground improvement and pre-support techniques used in the preliminary and final design of the project

By K. Short

Over the past several years, the mining and minerals market was overloaded with discussions around reviving mature terminologies like distributed control systems (DCS), programmable logic controllers (PLC), and the ?new comers?: hybrid control systems (HCS) and programmable automation controllers (PAC) and, in parallel, which technologies would be more appropriate for mining and mineral processing applications. Ten years ago, a careful comparative analysis would make more sense. Control approaches had very distinctive differences where users needed to choose the right approach.

Jan 1, 2012

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

The National Mining Hall of Fame will hold its 13thAnnual Induction Banquet during MINExpo International 2000 in Las Vegas, NV. The gala black-tie (optional) event will honor eight legendary leaders of the mining industry. The event will take place at the Las Vegas Hilton Hotel on Sunday, Oct. 8. The induction ceremonies will salute mining greats elected by the board of governors from a list of nominees submitted by mining industry partners and the public. The members of the Class of 2000 will join 151 other inductees enshrined in the Mining Hall of Fame in Leadville, CO. The evening will begin at 6 pm with a cash bar reception followed by the banquet and program at 7 pm. Keynoting the banquet program will be Harrison (Jack) Schmitt. He was the geologist/astronaut of the Apollo 17 mission to the moon in 1972 (see related story on page 26). And he is the only scientist to “kick rocks on the moon.” Schmitt is also a member of the Mining Hall’s board of governors. Schmitt was also the keynote speaker at the First Annual Induction Banquet in Denver, CO in 1988.

Jan 1, 2000

By S. Constantinides

Over the past 100 years we have witnessed a revolution in permanent magnetic materials. Prior to 1932 electrical machinery depended upon steels for both the soft and the permanent magnet structures. Because permanent magnet steels were easily demagnetized, motors, generators, loudspeakers and similar devices often used the interaction between two electromagnets. Motors and generators were mostly of the induction type, depending for function upon induced fields. The discovery of Alnico in 1931 and its rapid commercialization presaged an expansion of the industrial revolution and today, permanent magnet structures are widely utilized. [ ] DEVELOPMENT OF PERMANENT MAGNETS Act 1: Early Days of Permanent Magnets Alnico, which stands for aluminum, nickel and cobalt, is a family of alloys with similar structure and processing requirements. Additional elements, such as copper and titanium, are present in minor amounts to optimize magnetic properties. Alnico is known by many trade names around the world including Alcomax, Hycomax, Ticonal, Nipermag, Koerzit, Oerstit, Nialco, etc(1,2,3). In addition to the generic name ?alnico?, it is usually appended with a number representing the magnetic grade.

Jan 1, 2011

By Andrew McGrath, Geraldine Lyons, Sarah Barcelona

In the dynamic and challenging modern industry landscape, understanding and unleashing the true role and contribution of technical teams is crucial to business success. The cyclical nature of industries has led to shifts in the technical professional’s place within the organization and the technical skills that are desired most. This paper reframes the pivotal role that technical professionals play within complex operating assets to maximize value and realize full potential. This investigation focuses on the Rio Tinto Kennecott Technical group’s cultural journey, which is underpinned by an investment in its people. The conflict between legacy industry beliefs and the necessity for cultural change emerges. This is illustrated by a deep dive into the evolving case study of Kennecott’s Bingham Canyon Open Pit Mine Technical team. Here, a multi-faceted approach to cultural change is helping to unlock the team’s contribution to the life extension of an aging asset. Guided by a vision and strategic roadmap, this approach is part way through a 5-year implementation period and is yielding encouraging business outcomes.

Feb 1, 2024