Search Documents

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona's BHK System.

Jan 1, 1990

By Jordan Scheremeta, Sudhir Tripathi, Mahfooz Alam

Injection leaching can improve leach ore recovery by displacing retained solutions, enhancing ore wetting, and creating new flow paths for efficient solution collection. This paper presents a method to assess the feasibility of injection leaching in finer-grained, potentially contractive ores (from a geotechnical slope stability perspective) using limit-equilibrium (LE) slope stability analysis and static deformation modeling. LE models were carried out by assigning peak undrained strengths to the heap leach ore material, and modeling the excess pore pressure induced during the injection leaching process using spatial function in Slope/W. Static deformation modeling was completed using the software Fast Lagrangian Analysis of Continua (FLAC) to evaluate the potential for deformations due to the excess pore pressures induced during the injection leaching process. A constitutive model was used to represent the geomechanical behavior of the leached ore material, which enables the prediction of deformation and potential stability issues resulting from excess pore-pressure induced during injection leaching process. The two-pronged approach provides a practical method to assess geotechnical impacts and guide data-driven decisions in injection leaching operations.

Feb 22, 2026

By Volkan Arslan

This study aimed to remove the contaminants in quartz sand by using an eco-friendly method and to obtain high-purity quartz. For this purpose, ultrasound-assisted acid leaching was applied. Equal amounts of a mixture of diluted hydrochloric and oxalic acids were used as the solvent. Response surface methodology (RSM) was used for optimizing, modeling, and predicting the experimental parameters. The correlation coefficient ( R2) of the proposed quadratic model for the relationship between iron removal yield and test parameters was calculated as 0.9731 and it was determined that the predicted and actual values were compatible. Finally, optimization experiments were made and optimum experiment conditions were revised and determined as 83.38 °C of leaching temperature, 196.35 min of leaching time, 2.86 M of acid concentration, and 202.24 W of ultrasound power. Under the optimum conditions determined after optimization, the highest yield of iron removal was determined as 95.08%. Under the optimal parameters, the SiO2 content of the concentrates increased from 97.841 to 99.907% and the Fe2O3 content reduced from 0.225 to 0.011%.

Jul 12, 2021

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By Jameel Menashi

Aqueous solutions of Na2Cr04 can be reduced with CO to produce hydrous Cr203 and NaHCO3/Na2CO3. CH3OH, HCOO and HCHO in the presence of CO2 also reduce Cr 6+ and yield similar products. It is shown that the rate of Cr6+ reduction can be represented by the expression -d[Cr6+]/dt=k[Cr6+)1/2[R] where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mole. Rapid reduction rates are attained at temperatures in excess of 220°C and, with these three reductants, a green acid-insoluble readily filterable hydrous Cr203 is formed. With HCHO significant reduction of Cr6+ occurs at about 80-100°C and an acid-soluble violet modification of hydrous Cr2O3 is formed. The reduction process is reasonably selective: solutions of Na2CrO4 contaminated with Mo6+ and W6+ can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels. These findings are utilized as a basis for a process for recovering chromium from secondary source materials.

Jan 1, 1984

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"The Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million people. The project was constructed by a joint venture (JV) of four South American contractors and consisted of the following key components:• Treatment plant: A 16-ha (39-acre) area was cleared for the construction of a treatment plant to purify 900,000 m3/day (1.2 million cu ft/d) of raw water from the Paraná River and distribute it to the surrounding communities.• Bored tunnel: Nearly 15 km (9 miles) of 3.6 m (12 ft) inner diameter tunnel, ranging from 18 to 22 m (59 ft to 72 ft) below grade, was bored with two earth pressure balance (EPB) tunnel boring machines (TBM) to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions. Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access and ventilation shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (intake and treatment plant, respectively) and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installedafterward."

Sep 1, 2016

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By P. Bissert, M. Klein, L. Yan, D. Yantek, R. Matetic

"U.S. Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hours. One of the main concerns with the use of mobile RAs is heat and humidity buildup inside the RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in an occupied RA not exceed 95 °F. To investigate this, the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4 °C (17 °F) and the relative humidity approached 94 percent at the end of a 96-hour test. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the volume-weighted average air temperature inside the RA tent at the end of 96 hours to within 0.06 °C (0.1 °F) of the average measured air temperature. IntroductionIf an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter a refuge alternative (RA) for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration, and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke or even death."

Sep 1, 2016

By S. K. Sahoo, S. K. Sharma, U. K. Singh, G. S. P. Singh

This research focuses on the strata control issues in a Bord and Pillar depillaring working under the influence of dead load condition of voluminous and fragmented softcover of overburden dump material. It reports the modeling of a mine working through the FLAC 2D software under the Indian geo-mining conditions. The modeling results of an actual mine working under softcover were compared with that under the intact overburden condition to assess the influence of the soft overburden over the depillaring working. The modeling work involved progressive caving of the strata and the cyclic goaf filling following the modelsimulated occurrence of main fall and periodic caving. Mohr-Coulomb Failure criteria along with a simplified strain-softening (MCSS) model was used to study the failure and caving mechanism. Salamon’s compaction model was used to simulate compaction and resultant stress recovery in the goaf material. Comparison of the model findings was done in terms of load on supports, abutment stress, and convergence, apart from the stress redistribution and failure mechanism. The load transfer mechanism of the soft overburden was also studied for an overall understanding of the strata behavior in such workings.

Jun 16, 2020

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remotecontrolled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures.

Jan 1, 2016

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By Robert Hochscheid

A patent issued to J.N.J. Leeman (1957) described the change in performance that takes place when a cyclone is installed in the horizontal position rather than the vertical position. Although this patent was directed more toward improvements that could be realized in the heavy medium cleaning of coal, it contained specific references to reducing the quantity of fine solids that would report in the underflow, and an example for fine sand classification is also included. The three cyclone installations for which data is given in this paper demonstrate that horizontal mounting of large cyclones can improve classification efficiency, eliminate some operational difficulties, and reduce cyclone maintenance requirements in closed circuit grinding installations. Cyclone Experience at Serrana S.A. Each of four grinding circuits at the Serrana S.A. de Mineracao Apatite flotation plant in Brazil have a 2.7 X 4.6 meter (9 X 15 foot) rod mill and each originally operated in closed circuit with two vertically mounted Model D20B (500m nominal diameter) Krebs Cyclones. New feed size is 25mm. The Apatite is liberated at a relatively coarse 35 to 28 mesh grind, but the 500mm cyclones had to be fed at 66 pct. solids in order to obtain an overflow analyzing 12 pct. coarser than 42 mesh. Because dilution water in the cyclone feed had to be limited, classification was inefficient, and there were other significant circuit difficulties as summarized in a recent article by C. A. Busnardo (1984):

Jan 1, 1985

By Frederick Bradley Henderson

This study was initiated to investigate the occurrence of cinnabar in the oxidation zones of some mercury sulfide deposits. Seven mines or mine districts were visited and samples were taken from both the oxidation and primary zones of these deposits in order to compare their mineralogies and assess Vie chemical changes that took place during oxidation. As a result of the study of these specimens, several limiting factors are suggested for the chemical environments and processes active in both the deposition and oxidation of mercury sulfide deposits. The Mt. Jackson mine, near Guerneville, California (location map, fig. 1), was studied in some detail and forms the basis of this paper. The mine has not heretofore been described in detail in the literature. The Mt. Jackson mine is considered typical of mercury sulfide deposits occurring at the faulted boundaries of serpentinite bodies and enclosing sediments. Such mines are common in the California and Oregon Coast Ranges? Specimens collected by the author from the New Idria and New Almaden districts, the Mt. Diablo, the Culver Bear, and the Buena Vista mines in California, and the Opalite district (Cordero and Bretz, mines) on the Oregon-Nevada border were studied for comparison with the Mt. Jackson samples. The mine description, maps and sketches were composed from field maps kindly provided by Francis Fredericks, consulting geologist to the Sonoma Quick-silver Mine Inc. during the author's visit in 1962. Additional information was obtained from the company maps and minor corrections and interpretations were added by the author.

Jan 1, 1965

By Martino Scialpi, Miriam Piemontese, Claudio Cimiotti, Matt Kendall, Nicholas Karlin, Roberto Schuerch

The Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to the White Point Manifold. Upon completion, through ground conditions ranging from soils to hard rock, the tunnel will be approx. 7 miles (11 km) long with a finished internal diameter of 18-ft (5.5 m). This paper will present the Tunneling Condition Assessment Report (TCAR) and Tunnel Operation Plan (TOP) developed prior to construction, as well as the actual TBM performances achieved along the northern portion of the alignment in soft ground, shallow cover, and beneath a densely urbanized area.

Jun 23, 2024