Search Documents

By Shuchen Sun, Ganfeng Tu, Chuan Liu, Xiaoping Zhu

The hydrometallurgical residue generated during the hydrometallurgical processing of waste automotive catalysts is valuable as a secondary resource. In this study, a process of platinum recovery from the hydrometallurgical residue by high-temperature smelting process was proposed. Results of lab- and pilot-scale experiments show a high recovery of more than 98% of platinum and glass slag was successfully obtained by controlling the Fe3O4 addition, C/Fe3O4 mass ratio, CaO/SiO2 mass ratio, smelting temperature, and holding time at 15 wt%, 0.4, 0.6, 1500 °C, and 120 or 60 min, respectively. Results from the pilot-scale show that the platinum contents in the glass slag and alloys were less than 4 g/t and more than 0.6 wt%, respectively. Therefore, the process proposed in this study is a prospective and effective approach for reutilization of hydrometallurgical residue containing platinum.

Oct 12, 2020

By Utku Gumus, Ertan Bostanci, Hanifi Copur, Ahmet Rüfai Bilgin, Ugur Altay

"Field observations on replacements of 12-inch constant cross-section double disc cutters in Tuzla Wastewater Tunnel excavated by an EPB TBM with 3.151 mm excavation diameter excavating hard rock are summarized. Cutter life is correlated to rock’s uniaxial compressive strength and Cerchar abrasivity index, and TBM operational parameters. Number of cutter replacements, average cutter replacement rates and types of cutter damages are summarized. The relationships between cutter life and rock properties and TBM operational parameters are analyzed by single variable regression method. Detailed analysis between chainages 1+200 and 1+982 km indicates that average cutter consumption rate is 35.7 m3/replacement (4.6 m/replacement). Cerchar abrasivity index and uniaxial compressive strength does not indicate any meaningful relationship with cutter life. Penetration per revolution and field specific energy might be used for predicting lives of constant cross-section double disc cutters. However, additional data is required to generalize the findings of this study. INTRODUCTION Cutter life / replacement and/or consumption rates in terms of cutter cost and replacement time loses is one of the most important parameters affecting excavation performance of mechanical excavators, especially of TBMs used very widely and equipped with usually disc cutters. Predicting cutter cost is a very important task in especially feasibility stage of tunneling projects. Basic parameters affecting cutter life can be classified into 3 general groups as geological and geotechnical, excavation machine (TBM) related, and operational parameters (Bilgin et al., 2013). The geological and geotechnical parameters are the most dominant ones among them. The machine related parameters should be arranged in accordance with the expected geological and geotechnical conditions for the best TBM excavation performance and minimum cost."

Jan 1, 2016

By R. S. Jurani

Sunshine Mining Company's Kellogg operation is the primary silver producer in the United States, and maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and uncertain silver market, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a 2-year, $400 000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants, thereby saving the company approximately $650 000 per year.

Jan 1, 1987

By Young C. Kim

Introduction and Objective of This Paper Computerized open pit mine models* are more and more used today for feasi¬bility studies as well as for long range mine planning. In fact, using these models is becoming an enforced practice due to various reasons. One main reason is its capacity to evaluate several designs in a fraction of time required by manual effort. Another reason is the necessity to evaluate several. pit designs due to ever decreasing grade of the orebody and increasing financial risk due to smaller profitability margin. In spite of today's accepted use of computer models, very little guidelines are available which the average practitioner can follow either to choose or to build the type of model best suited for his need. Consequently, the objectives of this paper are: 1. To review the current state of the art in the computerized open pit mine models. 2. To provide some suggestions for model selection. 3. To share our experiences in developing a model for a highly irregular copper ore deposit (see Appendix).

Jan 1, 1977

By Jamal Rostami, Mark Board, Clayr Alexander, Muthu Vinayak Thyagarajan

In the past several decades, many major equipment manufacturers have ventured into developing new technology for underground hard rock excavation. This includes variety of configurations for full and partial face mobile excavation units. Mining industry prefers machines that can excavate noncircular, flat invert profiles and be able to make tight turns in hard rock. The need to use disc cutters for cutting hard rock has impeded the development of such machines due to the need for gripper system or large mass of a machine to support the force requirements of the disc cutters. Most of the prior attempts have been partially successful and the operations have faced some practical limits and challenges. Among the units that have been successfully used, one can name mobile miner, which was used for rock excavation in some projects. A redesigned mobile miner, called the “Remote Vein Miner,” or RVM, has been developed by Epiroc for underground hard rock mining in Hecla’s Lucky Friday Mine. This equipment potentially opens numerous opportunities for innovation in civil tunneling projects, where the operational flexibility and accessibility of a TBM’s limited tunnel path, design of the profile, and cost are limiting factors. This paper explores the application of the RVM in tunneling projects, its advantages and possible areas of innovation in tunnel planning and design.

Jun 13, 2021

By Ingunn Opland, Silje M. Tinderholt

Drill and blast project in Norway’s capital. The contract consists of 7 rock caverns (350–950 m2), 9.2 km tunnels, and four shafts. With 110 blue-collar and 31 white-collar, the project produces an average of 16–21,000 m3 hard rock per week, with a total of 19 tunnel faces. Weekly, nine grouting rounds for water control, 800 m3 shotcrete, and 1,200 bolts are required, and 60 trucks leave the site pr. day. Challenges include blasting in densely populated areas, planning and coordination to maintain high production, obtaining a CEEQUAL certification of very good, and transporting rock on Oslo’s main highway.

Jun 13, 2023

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By Herbert H. Einstein

Swelling ground is one of the most feared problem in tunneling. Although usually not causing sudden failures during construction, the very large and long- lasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners of up to 1 m that have been cracked or crushed, tunnel inverts that are heaving at a rate of 0.1 m per week during construction and continue to heave during decades. This author (Einstein (1979). Einstein et al. (1972) (1975)) and others (Huller (19761, Grob (1972) (1976). Golta (1967), tienke (19761, Krause (1976). Lee et al. (1976)) have described many cases of swelling tunnels that illustrate the significance and magnitude of the problem. This paper intends to show that tunnels in swelling rock can be built to perform satisfactorily. . For this purpose the tunnel builder needs to know how to determine the existence and specific behavior of swelling ground, how to select appropriate structural characteristics of the tunnel and predict its performance under the specific ground conditions, and finally how to construct the tunnel such that the anticipated performance will be achieved. This concept of a design-construction procedure is the same as that for tunneling in general; it is mentioned here for NO reasons: 1. To point out that design and construction cannot and should not be separated. The way in which the tunnel will be built has to be an integral part of the design. 2. This paper will be structured corresponding to the procedural concept.

Jan 1, 1981

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By H. Reed

The precious metal mining industry in Nevada handles and generates a certain amount of hazardous materials and waste on a regular basis. These products range from processing material additives to wastes from laboratory testing, heap leaching, and hydrocarbon treatment and disposal. The volume of materials and wastes is dependent upon the amount of ore processed. Handling, treatment and disposal is dependent on the type of material handled and the waste generated. Owing to the health and safety concerns and due to the existing regulations that control handling and disposal of hazardous materials and wastes, the mining industry is obligated to comply with all applicable requirements for proper handling of these products. Plus, in an effort to minimize any impacts from this effort, the industry is continually looking for alternative methods to accomplish these requirements and to also minimize costs. This paper will discuss the general, and in some cases the specific conditions, by which the industry is coping with the issue and efforts to minimize any impacts from handling, treatment and disposal for hazardous materials and wastes. The subject of compliance with the Toxic Release Inventory (TRI) requirements and bio-treatment of wastes and other technologies will be discussed.

Jan 1, 2001

By B. K. Cantrell

The use of diesel equipment in underground coal mines is controversial because "whole diesel exhaust" is regarded as "a potential occupational carcinogen" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2' and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.

Jan 1, 1991

By Zhongwei Wang, Dong Wang, Feng Ju

The coal seam in the southern coal field of the Ordos Basin serves as the main aquifer, while the region is known for its high-intensity coal mining activities. The coupling effect of mine water and the strong disturbance caused by high-intensity mining have brought serious challenges to the stability of coal pillars. To address this, a formula for determining the reasonable width of coal pillars under the aforementioned coupling effect and establish a criterion for coal pillar instability in this paper. A case study was on the 11,215 working face at the Xiaojihan coal mine in the area to investigate coal pillar stability. Results indicate that the strength and stability of the coal pillar are affected by the water content, with a small water content increasing its strength and large water content weakening it. In high-intensity exploration of watery coal seams, the best stability of the coal pillar is achieved at optimal water content and mining rates. For the Xiaojihan coal mine, the optimum water content and mining rate are 3.31% and 20 m/d, respectively, ensuring the efficient mining of watery coal seams. Furthermore, this study's findings can provide valuable references for the mining design of coal mines with similar geological conditions in the region.

Feb 13, 2024

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By Feridon Ghadimi, Saeed Mojeddifar, Massume Khavari

Separation of geochemical anomalies from background is an important and essential issue in the exploration of mineral deposits. Statistical methods are used to separation of anomaly from background. Fractal/multifractal and singularity methods are very suitable for the separation of weak anomalies. For interpolation, various methods could be used such as most distance-weighting methods, kriging, spline interpolation, interpolating polynomials, and finite difference methods. This paper addressed application of multifractal techniques together with finite difference procedure to detect the anomalous regions. Fractal models such as concentration–area, spectrum–area, and singularity index model were selected to identify Pb–Zn anomalies. In this research, 170 samples from 33 boreholes were taken in the Haft-Savaran area and analyzed for determination of Pb–Zn anomaly. Singularity method was a suitable method for separating Pb and Zn anomalies. Also, the results showed that the geochemical anomaly has occurred along NE–SW trend and is consistent with the sulfide mineralization process and the faults of the region.

May 18, 2020

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By J. Stawovy, A. Fourie, J. D. Quaranta

Coal refuse impoundments are disposal facilities specifically designed for the coal mining industry. Re-purposing refuse impoundments for co-disposal with natural gas flowback water and waste rock overburden has been investigated. The aims of this study were to investigate properties of coal refuse classification under the influence of co-disposed wastes as geochemical material exposure pathways from hydraulically exposed sodium and calcium ( Na+, Ca2+) cation loading from disposal of flowback water produced during the development of horizontal drilled natural shale gas frack wells, and waste rock having limestone characteristics. The geotechnical index classification of saturated cohesionless refuse is required to evaluate the liquefaction potential for strain or strength loss contributing to ground movements. This study is relevant to identifying changes in the coal refuse geotechnical index classification as sand-like, clay-like, or a borderline transitional material from the effects of ion and waste exposure in the impoundment’s reservoir porewater. Laboratory geotechnical tests were performed on fine coal refuse blended with different cations to classify the altered plastic behavior and index classification. Following determination of the index classification, the specimen’s stress–strain responses were investigated through isotropically consolidated undrained (ICU) triaxial compression tests. This experimental study culminated with two salient findings: the first is that introduction of ions alone into the refuse tailings or impoundment porewater resulted in significant material changes in property index classification, and the second finding was that the difference in refuse index classification did not correlate into noticeable effects of the monotonic undrained triaxial strength parameters.

Jul 5, 2022