Search Documents

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By M. Werner

Mining in the Coeur d'Alene Mining District has been going on for over 100 years with a long- term continuation very likely. Mining is presently carried out at depths below the -5000' horizon. As mining continues at ever increasing depths, higher in-situ rock stresses and subsequent rock deformation is encountered making mining costly and hazardous. To provide access for men and materials in such areas, a wooden raise preparation structure is typically built. Although these structures provide adequate support and access, they have proved to be very costly to construct and maintain.

Jan 1, 1986

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019

By Pafos Busch, Martin Fischer, Johannes Jaeger

The Spitzenberg Tunnel is a 600 m (1,970 ft) long twin tube motorway tunnel on Germany’s Autobahn A44 between Kassel and Eisenach. Since flexibility was considered to be very important in the continuously changing geological conditions, NATM was chosen as the construction method. When passing an old quarry with only 1,80 m (6 ft) of overburden, the excavation works became extraordinarily challenging. This paper not only describes the special methods, like double sidewall drifts and pipe umbrellas applied in this zone but also highlights the cooperation between the parties involved, which in combination made the project a joint success.

Jun 13, 2021

By Peter Schmäh, Tobias Engel

The E-Power Pipe technology was originally developed for the trenchless installation of protective pipes and pipelines of 10" to 28" diameter, over long distances of more than 4,000 ft. The twostage process combines elements from Horizontal Directional Drilling (HDD) and microtunnelling technology. A microtunnelling boring machine (MTBM) excavates the borehole using a specially designed, temporary jacking pipe. A Rack & Pinion jacking frame pushes the equipment during the pilot bore and pulls in the prefabricated pipe string in a second step. The slurry microtunnelling machine is equipped with a jet pump, creating the so-called AVNS machine type. A new generation of small hard rock cutting wheels complements this considerable achievement for the tunnelling industry

Dec 1, 2022

By R. A. Metz, Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity,' innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1992

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.'s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By Germán Toledo

The closure of TSF represents a critical milestone in the life cycle of mining operations, requiring the integration of technical, environmental, and social dimensions to ensure long-term safety and sustainability. The GISTM introduces the concept of “safe closure” as a demonstrable technical condition in which there are no ongoing material risks to people or the environment. This status must be validated by an independent technical reviewer and formally approved by the Accountable Executive. This article presents a risk-based methodology to support the achievement of safe closure, aligned with the principles and requirements of the GISTM. The proposed approach emphasizes the need to identify, assess, and manage closure and post-closure risks progressively throughout all phases of the TSF life cycle: from site selection and design, through construction and operation, to closure implementation and long-term monitoring. The methodology integrates key elements of effective risk management, including comprehensive knowledge bases, consideration of climate change, credible failure modes, continuous monitoring, stakeholder engagement, and governance. The ALARP principle is applied to demonstrate that residual risks have been reduced to tolerable levels. By incorporating closure planning from the earliest stages and adopting a risk-based view throughout the entire life cycle, this methodology aims to support mining organizations in achieving a verifiable and responsible closure of tailings facilities, in line with international best practices such as those of ANCOLD and ICOLD. The proposed framework offers a practical contribution to strengthening the credibility, effectiveness, and sustainability of tailings closure processes.

Feb 22, 2026

By Yubo Tu, Lianqi Wei, Tianyi Zhao, Peiwei Han, Zhengchen Li, Shufeng Ye

The effect of oxygen partial pressure on the volatilization percentages of valuable metals from iron-rich pyrite cinder by chlorination-volatilization method using CaCl2 as chlorinating agent was investigated in this study. The volatile products were collected directly and analyzed by X-ray diffraction. It was found that there were CuCl2, CuCl, PbCl2, and ZnCl2 existed in the volatile products. Au and Pb volatilization percentages were almost not affected by oxygen partial pressure. Both Cu and Zn volatilization percentages were negatively correlated with oxygen partial pressure when CaCl2 dosage was no more than 4 wt%, and almost uncorrelated with oxygen partial pressure with a CaCl2 dosage of 6 wt%.

Dec 19, 2023

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By R. C. Ford, J. Kelsey, S. A. Pierce, M. D. Ankeny

Evaluation of acid drainage risk from spent (leached) ore in arid climatic zones consists of two components: (1) whether residual and secondary minerals will release acid and metals when exposed to rainfall, and (2) whether ambient rainfall is likely to infiltrate, and eventually impact surface or ground water resources. The risk of acid drainage from spent ore at the El Abra on-off copper leach pad operation was evaluated using conventional geochemical methods and unsaturated flow models. Although geochemical testing indicated poor quality water would result from any seepage, unsaturated flow modeling demonstrated that infiltration and seepage were unlikely given the arid climatic conditions. Modeling further demonstrated that the residual moisture content of the spent ore when it is removed from the leach pad controls the risk of seepage. To further reduce the risk of seepage, operational controls were developed and implemented at the El Abra site.

Jan 1, 2000

By A. Haghighat

The Missouri University of Science and Technology?s (Missouri S&T) Experimental Mine is a teaching and research facility which has been excavated in limestone by mining engineering students over almost 100 years. The mine is currently being extended to a second level. Available fans for ventilation are two surface fans of 24 kW and two underground booster fans of 12 kW. The design of a ventilation network in conjunction with multi surface fans and booster fans entails a complex procedure. Ventsim Visual software modeling has been used for network analysis to determine the optimum surface and booster fans locations, blade settings, and speeds. Both natural and mechanical induced ventilation pressures have been taken into account. Three working faces on each level have been designated as target points that minimum air quantities are required. The model has been calibrated against a pressure and quantity survey. Design of ductwork, door/stopping positions and different fans characteristics have been examined. The optimum flow rate at identified working faces, efficiency and minimum energy losses and annual network power cost determine the best scenario. The optimum design has been determined for the ventilation network for the next 100 years. The optimum flow rate across working faces is the key criterion selected.

Feb 23, 2014

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By V. Gall

The three-dimensional finite element technique combined with the progressive failure approach was utilized to simulate stress distributions in a mine section which occur in response to a longwall mining operation. Due to the availability of the Cray supercomputer, a large-scale three-dimensional finite element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1990

By Robert S. Holmes

The U. S. Army Corps of Engineers Explosive Excavation Research Office (EERO) of Livermore, California, has been engaged in research and development of excavation techniques using both nuclear and conventional explosives since 1962. Prior to July 1971, this organization was designated the U. S. Army Corps of Engineers Nuclear Cratering Group. The EERO mission is performed as part of the joint Atomic Energy Commission -Corps of Engineers nuclear excavation research pro-gram. During the period 1962-1969, the Corps executed many cratering explosions using spherical charges of up to 85 tons of nitromethane to model nuclear excavation concepts and to develop design criteria for the nuclear cratering explosions. The experience gained in these modeling tests suggested that explosive excavation using large chemical explosive charges could be applied to excavation projects as an economical substitute for traditional excavation techniques. Consequently, the Corps' research program was broadened in 1969 to include development of chemical explosive excavation as a construction tool. The term "explosive excavation" denotes the use of large buried explosive charges to produce an excavation by fracturing the material and casting it into a desired configuration. In its simplest form, this technology involves detonation of a single explosive charge buried at the proper depth to produce a crater which is roughly hyperbolic in cross section. The types of craters produced by various depths of burial are illustrated by Figure 1. Single or Multiple rows of charges are used to excavate linear cuts required for water conveyance or navigation channels. .More complex explosive excavations include small craft harbors, railroad and highway cuts, and removal of W1denvater rock barriers to navigation. While the literature indicates widespread use of large explosions in the (1) ERRO is a field activity of the Waterway Experiment Station, Vicksburg, Mississippi

Jan 1, 1971

By A. E. Michon

I am Alfred E. Michon, Vice President- International for Burlington Northern Inc. I work for BN's holding company and my responsibilities include co-ordinating the activities of our eight subsidiary companies as they relate to international commerce--an increasingly important aspect of the overall business of our company. Until last April, I was President of the Fort Worth and Denver and Colorado and Southern railroads, subsidiaries of BN. Prior to that, I headed the marketing and pricing area of BN's coal transportation business. Based on my experience in the energy industry, both domestic and international, I would like to discuss the world-wide trend towards the reliance on low-sulfur coal in lieu of natural gas and oil for the generation of electricity. Since pontification on the energy scene world- wide is best left to consultants with scenario-spitting computers, let me in- stead emphasize this trend through two examples. First I will describe the regulatory and economic factors which have encouraged the replacement of natural gas by low sulfur coal as a boiler fuel in the US. BN's investments in track and equipment were instrumental in this conversion. Secondly, I will show how this same combination of factors has created a large demand for steam coal in the Far East. Again, our company's strategy is to facilitate conversion to coal overseas through timely and sufficient investments.

Jan 1, 1982

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By Z. J. Hladysz

The Hladysz Rock Tester was developed at the South Dakota School of Mines as a portable rock strength tester. The hand held device is placed against a rock surface and struck by a hammer. The impacted force causes a steel ball in the device nose piece to indent the rock and simultaneously indent a standard steel bar also contained in the nose piece. By comparing the two indented diameters the compressive strength of the rock can be calculated using laboratory determined correlation coefficients.

Jan 1, 1984