Search Documents

By P. Verhoeven, G. Hefter, P. M. May

The dissociation (ionisation) constant of hydrogen cyanide, pKa(HCN), has been measured by high precision glass electrode potentiometric titrations in saline solutions containing up to 5 mol/L sodium chloride. The dissociation constant of water that is necessary for the calculation of pKa(HCN) has also been measured. In saline solution, and in contrast to literature values, pKa(HCN) changes considerably at both high and low ionic strengths as a result of changes in activity coefficients. In addition an equation is presented, using literature data, that describes the variation of pKa(HCN) with temperature up to 150°C. The significance of the changes in pKa(HCN) for optimising the pH of alkaline cyanide gold recovery streams is briefly discussed.

Jan 1, 1991

By Deepak Gupta, Brij M. Moudgil

Attempts were made to improve the recovery of coarse phosphate particles by adding selected frothers or precoated fine particles. A number of frothers for floating, specifically coarse coal and metallic minerals, were examined. Two of the frothers increased the flotation recovery of coarse phosphate by 3% on bench scale. Plant evaluation yielded improvements in overall phosphate recovery in the presence of these frothers. Addition of fine particles was also found to enhance coarse flotation under given conditions. Size, amount, and hydrophobicity of the fines added was determined to have a major influence on the coarse flotation efficiency. The grade of the product with and without frothers and particulate additives remained the same. Change in froth stability and viscosity are believed to be the primary reasons for enhanced recovery of coarse phosphate particles.

Jan 1, 1989

By D. B. Gentzler, J. L. Kohler

A method of monitoring production information (raw tonnage and machine state) from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1990

By H. H. Hayden

The accident repeater-40 you have one at your mine? Unless your company is vastly different from most coal companies, you will find that a small percentage (11-12%) of your employees will have a large percentage (47-50%) of your accidents. When you find out that this is a fact, what do you do? First, you establish a set of guidelines that can be used in identifying the ?accident repeater?. Next, you determine the type of action necessary to improve work habits and safety performance of the accident repeater. With these two steps in mind, objectives are developed for an ?accident repeater? program.

Jan 1, 1984

By W. Petruk

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections in order to characterize a mill product and to determine the apparent mineral liberation. It was found that a representive polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly individual screened' fractions are not representative of the sample because minerals are partitioned during screening. Consequently the quantities of soft brittle minerals are increased in fine grained fractions and quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (1 Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analysing each fraction and combining the data. Somewhat less accurate data would be obtained by analysing a series of screened, fractions that have a wider size range of particles (5 Tyler size ranges). Mineral liberation analyses show that the most reliable apparent mineral liberation in each screened fraction is a value taken from a smooth curve drawn through the lowest points on a graph of % free vs size. A correlation between the apparent mineral liberation in screened fractions and calculated mineral liberations using Kings liberation model is good for sphalerite but not for chalcopyrite and galena.

Jan 1, 1985

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By Dhananjay Kumar

In past, no serious attempts have been made to study the effects of operating environments on performance characteristics of a mining system. In this paper, proportional hazards model (PHM) analysis technique is introduced which can be used to analyze the effects of operating environments on the performance of a mining system. It can be used to select suitable materials, manufacturers or designs of items for a particular working environment. In this paper some applications of the PHM are discussed with examples from a Swedish mine. Its application for decision making in maintenance is also discussed.

Jan 1, 1992

By J. A. Herbst, Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous grinding mills through detailed mathematical models, a better understanding of the charge motion and rocklball segregation is needed. To achieve this a 0.61 m (2.0 ft) diam by 0.305m (1 .0ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video presentation (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rocksize distribution, and flow rates.

Jan 1, 1990

In addition to capital and operating costs, the accurate estimation of ore reserves is a key component to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by the improper estimation of ore reserves. The accurate estimation of an ore reserve relies heavily on an understanding of the geology and the underlying assumptions unique to the estimation techniques being used. These assumptions are reviewed, and the shortcomings of the estimation techniques and their possible impact on a given project's economics are discussed. The latest developments in geostatistics in overcoming existing reserve-estimation problems are presented.

Jan 1, 1998

By Steven G. Grannes

The Bureau of Mines, U.S. Department of the Interior, has developed a computer image processing algorithm to determine the size distribution of moving taconite (iron ore) pellets. This algorithm interprets line-scan images to measure pellet diameters. Pellet edge detection with a peak light intensity constraint is the basis of this technique. Preliminary error analysis indicates a normally distributed experimental error with a standard deviation of 0.09 and 0.15 for pellet diameters of 0.4 and 0.9 cm, respectively. System accuracy was independent of moving pellet speed below 50 cm/sec. Computer image-based size distributions were found to be in close agreement with standard sieve analysis.

Jan 1, 1986

By A. P. Grippo, L. B. Phelps

Many coal mining companies have potential surface mine reserves that either are known or suspected to have had prior drift mining activity on them. In many cases, there is no documentation on these mines or, at best, very fragmented records. These undocumented abandoned underground mines are creating engineering, financial, and environmental difficulties and concerns for both surface coal mine operators and regulatory personnel. This paper examines the use of resistivity techniques in detecting entries of abandoned drift coal mines. The detection of such a drift mine entry would confirm the presence and orientation of an abandoned underground coal mine.

Jan 1, 1987

By W. C. Bagby

The Dee disseminated gold deposit is the northernmost mine in the Carlin gold belt. We analyzed soil samples £ran undisturbed areas overlying the deposit to determine the usefulness of soil geochemistry in identifying ore zones. The depth of sampling ranged from 12 to 14 inches, depending on soil development. The -80 mesh fraction was analyzed by atomic absorption for Au, As, Sb, Hg, and T1 and by semiquantitative spectrographic analysis for Ag. Highly anomalous Au, Kg, As, Ag, and Sb are most closely associated with ore zones whereas T1 is more broadly dispersed. Hg is the only element that identifies deep ore.

Jan 1, 1984

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today's cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By B. J. K. Sullivan, Brian Hornsby

INTRODUCTION Mount Isa Mines Ltd. operates a copper and silver- lead-zinc property at Mount Isa in northwest Queens- land, Australia. Mount Isa is located in the tropics at latitude 20°43'S and longitude 139°30’E (Fig. 1). It is on the upper watershed of the Leichhardt River and at an elevation of 365 m above sea level. The average rain- fall is 360 mm/y, the greater part of which falls in January to March (the hot summer months). The mean summer temperature for these months is 30°C (dry bulb), with a maximum temperature of 43°C; the mean wet bulb temperature is 25°C with a maximum of 28°C. Mount Isa is located geologically towards the western edge of the Precambrian Shield of northwestern Queensland. This complex forms a north-tilting dissected peneplain which extends in the north-south direction for 640 km, with widths varying from 32 km to 190 km. The combination of differential erosion, regional strike, and steep dips has produced a corrugated topography of low north-south orientated hills and valleys. The field was first discovered in 1923 as a silver- lead-zinc field. Mount Isa Mines Ltd. was formed the following year and subsequently became the sole operating company on the field. Lead and copper ore have been mined and treated separately and simultaneously at Mount Isa since 1953. Intensive exploration commenced in 1954 and an active exploration program provided the justification for a series of production expansion programs in both silver- lead-zinc and copper (see Table 1 ). The most recent and largest production expansion program at Mount Isa commenced when a decision was reached in December 1969 calling for an increase in copper production from 100 000 to 150 000 t/y of blister copper. A major factor which influenced this decision was the substantial additions to the ore reserves in the so-called 1100 ore body which is a massive copper sulfide ore body with a known strike length of approximately 2500 m, a height which is variable up to 300 m, and a width of generally 300 m up to a maximum of 370 m (see Figs. 2 and 3). Host to the copper mineralization is a complex and variable rock generally called "silica dolomite." The ore body strikes 6.02 to 6.1 rad (345° to 350°), dips west between 0.78 and 1.13 rad (45° and 65°), and is truncated at depth by fault implaced basement rocks. It first occurs some 600 m below the surface and bottoms at about 1000 m below the surface. The unconfined compressive strength of the silica dolomite ore varies from 150 to 250 MPa, whereas the basement rocks, carbonaceous mylonite, slaty shale, buck quartz, and greenstone (a chloritic schist) are considerably weaker, varying in strength from 20 to 80 MPa. The distribution of mineralization within the ore body is variable, but can be considered as generally high grade at or just above the basement contact and diminishing towards the upper reaches of the ore body. The current

Jan 1, 1982

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

By B. W. Cavender

Innovative mining and metallurgical operating techniques and processes can be identified and developed by analyzing changes as they occurs within the mine, plant, technology or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions and the development of new knowledge. Innovation can be organized, practiced and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically designed policies regarding organizational structure and staffing, daily management practices and compensation and incentives.

Jan 1, 1996

By Carl E. Brechtel, Edward D. Thimons

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kw (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1987

By Eleanore L. Nestlerode, James R. Guilinger

In April. 1990 Addwest Minerals acquired the Phillips Ranch sulfur property. The sulfur deposit, hosted by the Permian Castile anhydrite, occurs as two distinct elongate. parallel orebodies within a series of northeast-trending grabens. After completing a positive feasibility study, based, in part. on successful drilling programs by Addwest Minerals and previous operators, the decision was made to place the property into production. Utilizing an existing on-site kasch plant, plus significant portions of the recently purchased Texasgulf Comanche Creek Frasch plant. Addwest is currently constructing an 800 long ton per day Frasch mining facility.

Jan 1, 1992

By Thomas H. Koenning

The number of spontaneous combustion incidents in the U.S. is expected to increase as the consumption of lower rank coals and the use of longwall mining becomes more prevalent. A spontaneous combustion incident holds the potential for substantial loss of life from a mine fire or explosion if not prevented or controlled at an early stage. Laboratory tests have been developed which are useful in ranking the susceptibility of various coals to spontaneous combustion. Ventilation circuits and mining methods can be designed to minimize the risk of spontaneous combustion. Early detection of spontaneous combustion is possible with the combined use of continuous monitoring, periodic gas sampling, and inspection.

Jan 1, 1989