Search Documents

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By R. S. Shoemaker

Environmental and regulatory authorities are increasingly requiring that precious metals heap leach piles be contoured before they are abandoned so they may present a more "natural" look to the eye. Depending on the ore type, many of these contoured heaps will be subject to substantial erosion by precipitation events, native plants will have difficulty in establishing themselves and slimes be washed onto surrounding areas or into watercourses. This paper presents the argument that the results of contouring heaps are counter to good environmental practice. Calculations which have been made demonstrate that leveling and berming the heap tops as well as berming the edge of each lift or setback will effectively prevent water erosion and promote the growth of native plant species.

Jan 1, 1993

By James R. Dunn

The mineral industry" has made and will continue to make important contributions to the growth of our economy. However, the industry is presently under continuous and increasingly severe attacks by organizations and individuals interested in the preservation of our environment. Yet neither the public interest value of preservation nor the public interest value of our mineral industry is known. In the absence of such values, judgments about best land use where minerals are involved are nearly always made on emotional grounds. An example of the sort of problem that has been created is in the New York Metropolitan Area. Because of institutionally-created shortages stemming largely from zoning decisions and building over deposits, the effective cost of fine aggregate delivered at dockside at Manhattan rose from $2. 65/cubic yard in July, 1969, to $4.10/cubic yard in May, 1970, this in spite of approximately ;l0,000 years of reserves on Long Island. The cost of fine aggregate for New York City alone has "Increased over $S million annually within one year, with the cost increase for the Tri-State Metropolitan Area (coastal Connecticut, New Jersey, and New York)" exceeding $10 million annually. The ab0ve situation has created a cost increase which is clearly the result of non-conservation of a mineral resource. That is, in readily measurable values, it Is costing the public about $10 million per year because good conservation practices were ignored-a public-interest loss. Admittedly, this is not the whole story because the public is simultaneously obtaining other values from the land surface that would otherwise have had to be dedicated, temporarily to be sure, to mineral recovery-a public-interest gain. However, the point is that we do not know where the balance lies-the net public interest value; it may lie one way for deposits zoned out of existence by a growing suburb, another for areas designed as permanent greenbelts, and still another for areas under new highways

Jan 1, 1971

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By Lawrence K. Nordell, Vinit Sethi

Published standards and specifications do not adequately cover engineered class pulleys for modern high strength steel cord belt conveyors. This paper discusses the Conveyor Dynamics, Inc. (CDI) design criteria and stress analysis techniques emphasizing the finite element method (FEM), fatigue failure criteria, design limits and manufacturing requirements to ensure successful and safe pulley installations.

Jan 1, 1993

By Y. Xi, T. M. Yegulalp

An availability approach for determining the capacity of a major Bucket Wheel Excavator (BWE) system to be used in the Yuabaoshan Surface Coal Mine in China is presented in this paper. Based on previous studies on other BWE systems for delay times due to internal and external causes and a four-level maintenance and repair schedule, a model was developed, taking into account all random failures, to present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity, are discussed.

Jan 1, 1994

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By Otto Braach, Wolfgang Frietzsche, Erdogan Gürkan

The Westerschelde Tunnel is located in the south of the Netherlands and links the two parts of the Provinces of Zeeland, Zeeuws-Vlaanderen and Zuid-Beveland, which are separated by the Westerschelde. Road traf?c has up till now taken the detour via Belgium or crossed by ferry. This unsatisfactory transport link signifies major economic disadvantages above all for Zeeuws-Vlaanderen. The first fixed link for road traffic between the communities of Terneuzen and Borsele are to be created by means of the two 6.6 km long tunnel tubes down to 65 m below sea level.

Jan 1, 2003

By Hamid Maleki

This paper reviews a study conducted for Australian Coal Research Limited (ACARP) to assist Anglo-American operations with better understanding of coal burst mechanics and control based on U.S. practical experience, investigations, and inspections in three major U.S. coalfields over the past 45 years. The study examined both nonviolent and burst-prone case studies to identify contributing risk factors and addressed failure mechanisms for major U.S. coalfields in Utah, Colorado, and Kentucky, which have diverse characteristics. To investigate the mechanics of coal burst, a multipronged approach is used. First, field measurements in three mines from East Mountain, Utah, are complemented with finite-difference stress analyses to address the importance of horizontal stress in coal pillar mechanics of violent failure. Second, the computational procedures for estimating seismicity resulting from slip along geological discontinuities are reviewed, as these measurements point to seismicity being the trigger mechanism for violent failure of marginally stable structures. This joint-slip seismicity mechanism is in agreement with the more recentimproved re-examination of mining-induced seismicity (MIS) data from the Crandall Canyon Mine, Utah by University of Utah (UOU). Third, a hybrid statistical-analytical methodology is applied for identifying significant factors affecting coal burst. It utilizes data from 30 case studies including those from Utah, Colorado, Kentucky, and other eastern U.S. mines. The statistical approach reinforces field measurements and points to strata rigidity, joint spacings, and horizontal stress field as significant factors affecting damage resulting from coal bursts. This provides practical capabilities for identifying operations of higher risk using a rigidity-cavability variable. Overall, the study provides valuable insights into the mechanics and risk factors associated with coal bursts in major U.S. coalfields. By utilizing a multipronged approach that incorporates both field measurements and statistical-analytical calculations, the study offers practical capabilities for identifying operations of higher risk and improving coal burst control.

Jul 1, 2023

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By F. F. Aplan, T. H. Wentzler

Limestone is potentially a low cost material for the neutralization of acid mine drainage and other acidic waters such as steel pickling liquor. Unfortunately, when limestone is reacted wit9 these waters containing large amounts of Fe , Fe+3, and SO4-2 , a coating of gypsum and iron hydroxides form on the surface of the limestone inhibiting further neutralization reactions. The nature of these coatings, their morphology, composition and thickness were evaluated using the scanning electron microscope and microprobe, and the kinetics of limestone dissolution was studied both in the presence and in the absence of the reaction-inhibiting coatings. These data were then correlated with the solution chemistry.

Jan 1, 1992

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

Because of its many advantages, roof bolting has been widely used in hard-rock underground mines. In this paper, the applicability of roof bolts to mine openings in frozen ground, and the affects of bolts on the stability of the openings are presented. A comprehensive finite-element program, ABAQUS, was used to analyze the temperature distribution, the stress field and the displacement, field around a mine opening. Openings that were supported by roof bolts and openings that were unsupported were both analyzed. The thermal and mechanical processes were treated as a quasi-coupled problem, with the thermal analyses being conducted first, followed by the mechanical analyses in each case. For the opening under consideration, i.e., a roof area of 15 m2, five to seven roof bolts are appropriate. When the number of bolts is less than five, the displacement within the ground can be improved only locally.

Jan 1, 1997

By Neville G. W. Cook, John Kemeny

Utilizing the principles of elastic-brittle fracture mechanics, stress-displacement relationships are derived for an elastic solid containing a slip plane consisting of various configurations of collinear arrays of cracks. These models take into account the heterogeneous nature of slip planes as observed in the lab and in the field, and are relevant to the behavior of rock containing faults, joints, bedding planes, and fractures. All of our models exhibit slip weakening behavior, and show regimes of both stable (aseismic) and unstable (seismic) deformation. For given configurations of cracks and applied boundary conditions, our results show explicit ly the energy released through unstable crack growth. For instance, it is found that two equal length cracks growing together release more seismic energy than, say, a large crack growing into a small crack. Also, by allowing cracks to coalesce, our models show multiple stick-slip events without crack healing or other geochemical means.

Jan 1, 1986

By D. Tolgyesi, L. P. Gignac

Mine development has evolved in the past 15 years from a human-paced system using hand-held drills and track-bound equipment to a mechanized system using specialized equipment for each component of the development cycle. In most Canadian hard-rock mines, face advance is achieved by the following sequential activities: drilling, explosive loading, mucking and ground support. The state-of-the-art for each work element is reviewed and methods for performance estimates proposed. The entire development system and its production capabilities are considered based on equipment reliabilities, spare units, haulage distances, and muck bay spacing. The effect of the number of working faces on the system's performance will also be analyzed. Manuscript not received in time for publication.

Jan 1, 1983

An information system (I/S) plan is a means for establishing and communicating the direction the organization intends to take to provide the information required for achievement of organizational goals and objectives. The rapid advancements in information technology, the increasing complexity of systems, and the growing dependence of mining companies on these information systems have emphasized the need for more comprehensive I/S planning. This subsection explores this need, the role I/S planning can play within a mining company, and finally describes a methodology for development of an I/S plan.

Jan 1, 1979

By B. Cavender

Mining managers trying to rapidly reduce production costs tend to implement a traditional set of topdown managerial practices: reductions in production volume, employee layoffs, renegotiation of supplier contracts, cancellation of employee training, restrictions on travel, reductions in office supplies, and so forth. While these practices do reduce costs, the benefits are often limited in both magnitude and duration, and the workforce is usually left demoralized. Successful cost-cutters take a different approach. They make the continuous reduction of costs a priority for all members of the organization, whether managers or workers. The culture of these firms emphasizes the commitment, voluntarily given, of individuals and work groups to this goal. Cost-cutting practices often reject all of the traditional methods mentioned above, but are far more numerous, innovative and successful. This culture of cost reduction is the result of a set of leadership competencies that establish direction for the organization, align the organization's various constituencies with this direction, and motivate and inspire the organization. Cost reduction then becomes a routine task rather than a heroic achievement.

Jan 1, 2002

By John S. Thayer, Frederick E. Brinckman, Kenneth L. Jewett, Gregory J. Olson

Interest and research in biorecovery of metals has focused mainly on cell-based metal leaching and precipitation. However, production of non-enzymatic metabolic products by microorganisms related to metals bioprocessing also deserves attention. For example, it is well known that biogenic inorganic (e. g. H2S04 ) and organic acids play a role in metal dissolution. There are other metabolic products of microorganisms which can catalyze useful metals transformations. These include methylated metabolites such as alkyl halides which can dissolve metals from ores and also reduce certain metal ions in solution to pure metallic particles. This paper describes some of our research on metal dissolution and precipitation by such metabolites. Examples include the production of high purity elemental metal particles of gold, platinum and palladium by volatile metabolic products.

Jan 1, 1989

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

By Neil Hillhouse

The Porgera gold district, like many other large gold deposits, has a long history of awareness, but only in the last five years has a geologic understanding of the district permitted the discovery of economically attractive gold reserves. The following sequence of events highlights the various significant steps in the evolution of the discovery process. The history of the district goes back about 50 years, and for several decades it was known only for its placer gold. Gradually, as gold became a more interesting metal, more and more attention was centered on the district. The sequence of events does not overstate the problems caused by isolation and climate, but the reader can imagine the difficulties inherent in such an area.

Jan 1, 1990