Search Documents

By A. W. Khair, S. S. Peng

Discussion by J. Parker Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa(4000 and 7000psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic'? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition of moisture, from sprays or from humid air? Did moisture weaken the rock? Did it cause the rock to expand quickly, thus to induce internal compressive stress? How can the near-vertical cutters, as shown in the photographs, be attributed to primarily horizontal stresses? Did the cutters follow any particular pattern in the development panels, which might be related to a particular stress pattern? For example, did they always appear alongside the stiffest pillar? Or always along the northwest rib? Was there any evidence of the pillars and entries "rotating" under the influence of differential horizontal stresses? How much did the entries and pillars rotate as the longwall face approached and passed? After rooffalls, did the openings assume shapes which would indicate a preferred shape in that stressfield and geology? Did crosscuts always survive without damage, as shown in the sketch?

Jan 1, 1992

By E. Viet Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corporation, Santa Rita, New Mexico, local studies of the dump leaching process were intensified. As these studies progressed it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between leach solutions and the copper-bearing material would determine, in great part, the recovery of values. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers), and mathematical or laboratory model studies. These methods have not proved completely satisfactory for the studies now being developed. Investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drill holes, which are petro¬leum exploration and development techniques for locating fluids and measuring porosity in the subsurface. Standard oil field logging equipment was leased, modified, and tested. After successful testing, the equipment was purchased for additional studies. Applications and results of the methods are described in this paper.

Jan 1, 1968

By Martin C. Kuhn

The use of tritium in manufacturing and its subsequent loss to the local environment in Tucson, Arizona resulted in a great debate relative to the physiological effects of low level radiation. This paper reviews some of the facts of the release and attempts to quantify the degree of hazard encountered by the local community. Some of the difficulties in assessing the true degree of absorbed dose and the assumptions necessary for calculation purposes are presented.

Jan 1, 1981

By David Lynn Passmore

The reliability of mine operators reports to the Health and Safety Analysis Center of the U.S. Deparetment of Labor of days lost from work by injured miners is .267.

Jan 1, 1985

By O. H. Rostad

The importance of geology in ore reserve estimation has been stated by several authors. King et, a1 (1982) reported that the geological factor was the key deficiency where serious weaknesses in ore reserve estimation appeared, especially in grade. The foundation for a successful mining operation is an ore reserve estimate that neither overstates nor understates the true situation as to tonnage and grade. Overestimation of reserves can have devastating economic results. Overestimation of tonnage may lead to wasting money on an overbuilt plant or worse yet, if grade is seriously overestimated also, to undertaking an operation that is doomed to economic failure from the outset. Understated ore reserves can result in building a plant that is smaller than optimum which may result in higher unit costs. At worst, understated tonnage of ore reserves can result in a missed opportunity for a profitable operation. Failure of the ore reserve estimator to properly take into account all geologic and allied factors pertaining to the deposit can result in an ore reserve estimate that is overstated either as to tonnage or grade or both. This paper will focus on these factors and will not discuss rules about distances above or below a drift that should be given a classification of proven or probable, etc. Each deposit has its own particular characteristics which often require modification of general rules for defining limits of proven and probable ore blocks that work satisfactorily in another deposit. A number of references are included which discuss some of these problems. Definitions of ore reserve classifications and an illustration are given in the Appendix.

Jan 1, 1985

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By Y. H. C. Wang

A detailed study of carrier flotation of kaolin clay using calcite showed the major beneficiation mechanism to be enhanced aggregation between anatase and calcite under intense agitation conditions. In order to develop an understanding of this selective aggregation, surface charge characteristics of kaolinite, anatase and calcite were studied under simulated flotation conditions. Zeta potential of all these minerals tended towards a constant negative value in ole- ate solutions under certain conditions possibly due to adsorption or precipitation of oleate on them. However, whereas the zeta potential of anatase in the oleate solutions was not influenced by the agitation level, that of kaolinite was found to be strongly dependent on the agitation intensity. The effect of oleate on zeta potential of kaolinite was reduced by an increase in agitation intensity. It is suggested that oleate is much more firmly bound to the surface of the anatase and that this preferential attachment is responsible for the enhanced selective aggregation of the anatase with calcite. Agitation level plays a major role in carrier flotation since intense agitation is considered to en- hance both the chemisorption of oleate on anatase and preferential detachment of calcium oleate precipitate from the kaolinite surface, all of this producing a large difference in the surface properties of anatase and kaolinite, and hence in their tendency to aggregate with calcite.

Jan 1, 1981

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite is one of the main players in the stability of drilling mud. Its particle size and particle size distribution significantly affect drilling mud’s rheological properties. Although the Specifications for Drilling Fluids Materials report on Oil Companies Material Association (OCMA)-grade bentonite states that the API recommended powder having 2.5 percent mass fraction as the maximum value of residue of diameter greater than 75 μm, there is no other information on the specific size distribution for API bentonite. It was found that API bentonite has a specific size distribution with specific mixing weights. It is important to investigate why that mixture represents the optimum properties of drilling mud and how each individual size fraction has a specific function in the mixture. To clarify the effect of individual size as well as the collective effect of the size distribution, API bentonite was classified into different size fractions, with each tested separately for controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness and packing density.

By S. C. Suboleski

In a high risk venture such as mining where capital is committed and contracts are signed on the minimum of information, decisions are based primarily on production forecasts derived through consideration of such factors as management-labor relations, mining practice, variations in physical conditions and the equipment applied. Among these factors, the physical conditions offer the least opportunity for control and, due to the wide range of mining conditions that may be experienced, little effort has been made to develop objective methods for measuring their effects on mine out- put. The aim of this paper is to demonstrate a method for assessing these relationships that can be applied under a wide range of conditions both in new mines and in working sections where there is a need to determine the impact of proposed operational modifications. psing empirical data from active underground mines, a mathematical model was developed to derive a set of regression equations for predicting production as a function of mining conditions

Jan 1, 1980

By Charles T. Holland

The tonnage produced on mechanized automated retreating longwall faces in the United States is growing rapidly. This time last year some 14 faces were operating, and in addition to that, three were known to be down looking towards revision or repairs before being placed back in service. These, it is believed, are now in service. It is estimated at the present time, therefore, that somewhere between 20 and 25 faces are being operated in the country. A survey made last year by the School of Mines, West Virginia University, indicated that longwall mining in general has been beset with a great many problems, some more serious than others. The problems that we propose to discuss here are those pertaining to roof and floor trouble in the tailgates. Longwalls are operating in this country at the present time under an overburden ranging from 200 feet to nearly 3000 feet. Main and tailgate entries are operating in panels of up to five each, with the width of the pillars between these entries varying from 20 to 50 feet. Face lengths are running from 270 feet to 670; actually a face 800 feet long should be possible. The most economical face is often spoken of as being around 450 feet.

Jan 1, 1969

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980

By A. C. Barlow

The use of deep wells for waste disposal is not a new technique. The production phase of the oil industry has been using this method to dispose of unwanted oil field brine since the 1930's The adoption of this method by other branches of industry, however, to dispose of manufactured wastes is a relatively new development, but one which is finding increased use (2). Deep well waste disposal is not an ordinary technique even though it is finding relatively wide application. In fact, just the opposite is true; it is still a rather extraordinary measure. It is not now, nor is it ever likely to be a disposal method which can be assured of success before it is tried.

Jan 1, 1964

By Jean Dupere

Mr. Chairman, Ladies and Gentlemen, I'd like to take just a moment of your time before we examine the current position of the asbestos industry and its market outlook to take a searching look at the product itself. I feel that if we are to understand the problems that beset this basic mining and manufacturing industry and, more important, if we are to appreciate the solutions to these problems that I plan to put forward in a few moments' time, then we had better look at asbestos from the proper perspective. Asbestos has a unique combination of properties - properties not found in any other natural substance or man-made material. This has resulted in asbestos finding its way - in fact, being welcomed - into literally hundreds of applications.

Jan 1, 1984

By D. W. Park

Artificial intelligence has emerged over the past two decades as an important problem-solving tool including techniques such as expert systems, neural networks, tree classification, fuzzy logic, genetic algorithms, etc. These methods can be employed to solve rock mechanics and ground control problems associated with the highly complex nature of rock masses and ground conditions. A current study at the University of Alabama focuses on development of an artificial intelligence system for real-time interpretation of the data collected from longwall monitoring stations, and development of an early warning system for prediction of undesired conditions and prevention of longwall-mine instability problems. This paper describes a ground control management system using UALSAS (The University of Alabama Longwall Stability Analysis System), which is being developed to facilitate maintenance, on-line analysis, prediction, and includes an early warning system. A detailed framework of computer algorithms and their applications are also discussed. The successful application of these artificial intelligence techniques will contribute to a safer and healthier mining environment.

Jan 1, 1995

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By B. J. Scheiner

The Bureau of Mines, U. S. Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. In field tests, phosphate clay waste has been dewatered from a nominal 2.5 percent solids to greater than 20 percent solids. In other field tests, coal-clay waste has been dewatered from a nominal 3 percent solids to greater than 55 percent solids, in addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12 percent solids to 40 percent solids.

Jan 1, 1983

By I. Iwasaki

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides were investigated as a part of a pilot-plant development project on the differential flotation of Duluth gabbro. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously-ground pulps. With the ball-mill-ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously-ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1981

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By J. H. Fowler

Canada's gypsum industry began over two hundred years ago in the Maritime Provinces when farmers attempted to supplement their incomes by selling "land plaster" to traders bound for the United States. Rising from such humble beginnings, gypsum now contributes significantly to the economies of nine of Canada's ten provinces. Thirteen open-pit and three underground mines produced a total of 8.38 million tonnes of crude gypsum and seventeen processing plants manufactured 2.49 million tonnes of finished products in 1985. Recent economic growth in North America has resulted in steady increases in gypsum production, however, competition from foreign producers and by-product gypsum poses a growing threat to Canada's gypsum mining industry.

Jan 1, 1987