Search Documents

By B. V. Knelson

Although the concept of centrifugal recovery has been around in one form or another for many years, it has not been until recent times that it has became clearly understood am properly put into perspective. Simplistic in theory, it is when one begins to examine the variables involved that the true complexities of this matter begin to emerge. In creating an enhanced g force concentrator, there are many aspects both positive and negative that are encountered.

Jan 1, 1989

By P. Rusin

A new bacterium, Thiobacillus cuprinus, can extract copper from chalcopyrite as rapidly as T. ferrooxidans. On solution with and without nutrient amendments and bacterial growth media were supplemented with T. ferrooxidans or T. cuprinus in shake flask studies. Both species extracted -42% of the copper using growth media. In one case, T. cuprinus solubilized approximately twice as much copper as T. ferrooxidans utilizing a seeded On solution. Thiobacillus prosperus also oxidizes chalcopyrite and tolerates high chloride concentrations. These sulfide-oxidizing bacteria are representatives of the mixed microbial community found in sulfide dumps. Rates of biological copper extraction from sulfide ores, using the native microbes, have been significantly enhanced by amending On solution with PGM.

Jan 1, 1994

By D. Marino

Over the last 20 years, the manufacturing sector of our country has been called upon to comply with ever core stringent environmental standards. The primary metals sector was particularly hard hit early on, to develop the technology, acquire the equipment, and implement the programs to eliminate or reduce the by-products of metal making. To this end, through a combination of technological innovation and extensive capital expenditures, the metals industry has met, and in many cases, exceeded the minimum standards. It is to this escalating cost - liability exposure issue - that Dereco has addressed itself. As we move into the decade of the 90's, the challenge facing the metals industry concerning the environment will be even more difficult than the previous decade. To focus in on one major aspect of legislated environmental regulations, the issue we will address today is; now that the by-products of metal production have been identified, accounted for and collected, how are they to be disposed of? During the course of this presentation, actual data will be presented from our 4 1/4 year on-site experience at J & L Specialty Products

Jan 1, 1992

By Philip Antunes, A. E. (Tony) Reschke

"INTRODUCTION Tunnel Boring Machine (TBM) operations require the injection of material into the annular tail voids as the machine advances ahead of the segmental concrete lining. This annular gap is created because the cutting diameter of the TBM has to be larger than the outer diameter of the concrete segments of the tunnel lining. Fundamentally, the two basic types of annular grout are thick, concrete like mortars and thin, mobile, two-component grouts. While some European countries seem to still favor the concrete like mortars, from a global perspective it is now the two-component type grouts that dominate the industry. Two-component type grouts are comprised of an “A” component grout (typically cement, flyash, bentonite and a retarder/stabilizer) and a “B” component accelerator (sodium silicate or water glass as it is sometimes known). They are thus sometimes referred to as A/B type or bi-component grouts and were pioneered by the Japanese over 30 years ago. They offer a host of operational benefits over thick mortars, such as reduced settlement (Feddema et. al., 2001), effective penetration of the void space, with less energy, and reduced strain on the segmented linings (Robinson et. al., 2007). Two-component grouts are highly mobile and can be pumped many kilometers. The use of a retarder/stabilizer can also extend the shelf life of the “A” component grout for several days while the early strength of the accelerated grout stabilizes the ground and supports the segmental liner almost immediately. The batch plants that prepare the two-component grouts use one of two possible mixing methods for preparing the “A” component grout. The simplest plants use paddle type mixers and numerous tunnels worldwide have been successfully grouted using this technology. However, a superior type of mixer is available, namely the high shear colloidal mixer. Keller Colcrete successfully pioneered the development of the colloidal mixer back in 1937 and for over 75 years colloidal mixers have been internationally recognised as the most efficient method of mixing cement based grouts (Houlsby, 1990). These mixers are used in grout preparation for radioactive waste encapsulation, hydro dam grout curtains, soilcrete jet grouting, soil nailing, and numerous other geotechnical applications. In tunnelling, these mixers are also used for ground treatment, compensation grouting and for the preparation of bentonite lubrication for pipejacking. It has been only within the last decade however that these high-shear colloidal mixers have been adapted for use in the preparation of two-component grouts."

Jan 1, 2016

By Edward H. Eisenbrey

This paper is primarily concerned with the exploration for massive sulphide orebodies. In a discussion of this type, it seems appropriate to establish a few definitions so that all parties may consider the same beast and its habitat. First, the term "massive sulphides", as used here, not only denotes a body of mineralized rock containing in excess of 50% sulphides by volume, but a mass of sulphides that respond as a conductor to the electromagnetic (EM) systems currently in use in exploration. "Disseminated sulphides" refer to all of those sulphide occurrences that respond to the Induced Polarization (IP) geophysical methods most commonly in use in porphyry copper exploration. This latter definition may also include the disseminated sulphide halos so frequently found associated with massive mineralization as well as banded and stringer sulphide mineralization. It is plain to see that these two end members of our definitions can easily blend into each other. The term "volcanogenic" refers here to any and all geologic processes that have their origin in volcanic activity. Thus we are concerned here with the exploration for massive sulphide ore deposits derived from and affected by contemporaneous and post mineral volcanic activity. Furthermore, most massive sulphide deposits are apparently formed in a submarine environment, deposited with extrusive rocks and sediments and/or chemical hot spring accumulations, then enclosed and protected by the addition of more volcanic and sedimentary material then, probably folded and deformed into one of their myriad of shapes.

Jan 1, 1973

By O&apos

Southern Ohio Coal Company (SOCCO) and the U.S. Bureau of Mines have identified techniques to optimize the use of scrubbers on continuous miners. The techniques provide maximum respirable dust control while maintaining a high output. The use of radio remote control and scrubber help to achieve greater advance between lifts by locating the operator in fresh air during the mining cycle. He is also kept away from newly exposed roof, which is not supported. An alternative to fan-powered scrubber was also evaluated at SOCCO. A high-pressure water-powered scrubber system eliminated the noise associated with fans, and achieved an intrinsically safe system. Experience in the use of these scrubber systems and remote control at SOCCO are discussed.

Jan 1, 1990

By Allan R. Ide

It is a great pleasure for me to speak-before such a prestigious group as the American Institute of Mining, Metallurgical and Petroleum Engineers. The substance of my talk today is the handling of coal and petroleum coke: their characteristics and environmental problems, and how we were able to correct the problems, prescribe the cure and enjoy the benefits. When coke first became a by-product derived from the oil refineries everyone would have been very happy if someone had offered to take this pro- duct off their hands. Unfortunately, there was no market at that time, and no one seemed interested. Soon thereafter, it became a sellable product and began to be shipped to many countries in the world. This was when all of the pollution problems began. I will be talking briefly about some of these problems and showing a short film on this subject afterwards.

Jan 1, 1984

By M. S. Riyazulla

The Hutti greenstone belt comprising predominantly of low-potassium tholeitic basalt has undergone regional metamorphism of a transition zone between greenchist to amphibolite facies. The important mineral constituents of the volcanic suite are amphibole and plagioclase which appear to be the product of regional metamorphism. These minerals have been recognized as the main indicators of metamorphic temperature and pressure. With a view to understand the P-T conditions of metamorphism of the belt, electron microprobe studies were carried out on amphibole and plagioclase and the chemical data was used to decipher the metamorphic conditions. The results obtained indicated a metamorphic temperature of about 6000 c and pressure of 5 kbs. for the Hutti greenstone belt.

Jan 1, 1996

By M. J. Meulendyke

An extensive program of marked ball wear testing (MBWT), laboratory corrosion studies, and worn ball surface analyses has been used to gain insight about the role of corrosion in the overall wear process. In some environments, localized corrosion is observed; the actual wear mechanisms in such cases are pitting/spalling and abrasion. Factors affecting the occurrence of pitting include the abrasiveness of the ore, corrosivity of the slurry, corrosion resistance of the media, and galvanic coupling effects. Elimination of pitting substantially improves overall wear resistance. When pitting is not observed, the contributions of general corrosion are significantly less.

Jan 1, 1984

By Andrew Allan

[The Thompson Creek Coal and Coke Corporation, a. mall company engaged in producing coal in the Rocky Mountains of Colorado, is currently engaged in a struggle of destiny to increase their production from inclined seam operation to compete with highly mechanized horizontal bed mines. This paper introduces some of the problems encountered it pitch seam mining as they apply to the convention, room and pillar system employed at the present time. Further described is the test work now being conducted to overcome these obstacles with an. attendant increase in productivity. Included in this test work is a mining machine designed especially for pitching seams, an automated longwall, and hydraulic mining of the latter compared with those of conventional work presently employed.]

Jan 1, 1965

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

The dissolution behavior of gold and silver from Au/Ag alloys in aerated cyanide solutions has been investigated using rotating disc electrodes. The variables studied included concentration of cyanide, oxygen partial pressure and rotating speed of the disc. The dissolution potential and the rate of dissolution were obtained in view of the anodic and cathodic current-potential relationships. The results were discussed in terms of a mixed potential theory. The results showed that the dissolution rate of gold and silver from the alloys was partially controlled by chemical reaction, but largely by transport of either oxygen or cyanide, depending on their relative concentration under the experimental conditions employed in this study.

Jan 1, 1995

By W. L. Dalke

The Minntac complex is a facility for production of iron ore pellets located on the Mesabi Range at mountain iron, Minnesota. It consists basically of a mine, crushing plant, concentrator, and a pelletizer producing twelve and one-half million tons of pellets annually. This paper deals with some of the aspects of the grinding circuits; but prior to that discussion, it might be well to briefly describe the flow of material in the operation. The crude ore, containing from 20% to 25% magnetic iron, is mined by 14-yard electric shovels. .the blasted ore is loaded directly into 50-yard side dump railroad cars and hauled to the crushing plant. Crushing is done in three stages, originally, two 60" primary crushers; four 7-foot standard secondary crushers; and six 7-foot short head tertiary crushers were installed, when the plant was expanded to double its capacity, five secondary and ten tertiary crushers were added. These were duplicates of the original 7-foot standard and short head crushers used in the original construction, there was no expansion of the primary crushers but a one-half-million-ton surge pile of tertiary crusher feed was added.

Jan 1, 1976

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By C. J. Greet

Grinding with an electrochemically inert grinding media (i.e., high chrome white iron) shifts the pulp potentials to more oxidising conditions, increases the dissolved oxygen content and reduces the EDTA extractable iron concentration when compared with milling with electrochemically active grinding media (forged steel). These changes in pulp chemistry produce cleaner particle surfaces, reduce reagent consumption, and increase concentrate grades and recoveries. This paper presents a robust laboratory test program that not only demonstrates the changes in the pulp chemistry, but also provide an indication of the magnitude of the metallurgical improvements that are possible. While laboratory studies are interesting, the proof is in the pudding! So, the paper provides an overview of plant trials conducted at several porphyry copper operations around the world: Newmont’s Cadia and Red Chris Operations, as well as Evolution Mining’s Northparkes Operation. These successful plant trials clearly demonstrate that selection of the right grinding media alloy will yield savings in grinding media consumption and reagent consumption as well as increases in revenue through improved copper and gold recoveries. However, many of the porphyry copper mines on the Eastern Pacific are copper-molybdenum deposits. The paper presents laboratory test results for typical copper-molybdenum operations and extrapolate these numbers to what might be expected should a plant trial occur.

Feb 1, 2025

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By P. A. Lindberg

Early Proterozoic ore deposits in the Verde district at Jerome, Arizona have produced 33.7 million metric tons of ore (1893-1975). The United Verde and United Verde Extension deposits produced most of the ore that yielded 1,644,323,100 kg Cu plus large amounts of Au, Ag, and Zn. These deposits are situated on the fractured and hydrothermally altered apex of a large submarine rhyolitic extrusive (Cleopatra formation). Precambrian lithologies are penetratively deformed and at Jerome the Fl folds plunge steep to the NNW. For the past two decades the volcanogenic model has superseded the replacement theory of ore formation.

Jan 1, 1992

By Jaime Adasme, Héctor González, Benjamín Celada

"INTRODUCTION Santiago de Chile is a 7 million inhabitant city which has a 103 Km long subway network operated since 1975 by Metro S.A. This network is used on a daily basis by 2.3 million people. In 2012 Metro S.A. started the biggest enlargement of the network in its history, through the design and construction of the new Line 3 (21.7 Km) and Line 6 (16.5 Km). The detailed engineering contract for civil underground works of Line 6 (L6) was awarded to the Consortium integrated by ZAÑARTU Ingenieros Consultores and GEOCONTROL S.A., in which Geocontrol was in charge of the design of 11 stations and 14.5 Km of tunnel. L6 crosses L3 in Ñuble and Ñuñoa Station, L2 at Franklin Station and ends, intersecting L1, at Los Leones Station as shown in Figure 1. LOS LEONES STATION DESIGN Location and Characteristics Los Leones Station is placed at the North end of the L6, next to the same named station of the L1 and it has four construction units, as is shown in Figure 2: I. Access Shaft (49 m x 47 m). II. Access Gallery (34 m long). III. Station Tunnel (120 m long). IV. Connection Gallery with L1 (104 m long). A singular feature of Los Leones is that the western section of the station tunnel, built from the access gallery, is located below an underground parking lot which is located in Providencia Avenue, as shown in Figure 3. It is important to highlight that the distance between the vault of Los Leones Station Tunnel and the foundations of the underground parking lot is only 6 m."

Jan 1, 2016

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980