Search Documents

By J. Trouw, W. de Bruijn, A. van Sandwijk, R. H. Heerema

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically prepared hematite powder evenly doped with 1 % by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous theimogravimetric and dilatometric analyses were performed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process. The results indicate that the degree of expansion or shrinkage of hematite during reduction is highly dependent upon impurities associated with the original material; marked differences in reduction rate and microstructure were observed as well. An important finding is that the influence of a particular additive can also strongly vary from one reduction stage to the next. The reduction behavior appears to be affected by the physical and chemical nature of the associations formed by the added elements.

Jan 1, 1990

By G. A. Plakhin, A. V. Luganov, V. A. Luganov, G. V. Gorbatenko

In order to extract gold from the complex sulphur-arsenic bear­ing raw materials and to remove arsenic and sulphur from the process in an ecologically safe form we have studied oxidizing roasting of highly arsenic gold bearing concentrates with soda, leaching of cinders, processing of the obtained solution and extraction of gold from the cake. There were processed concen­trates containing from 5 to 28% of arsenic, 12-20% of sulphur in the form of pyrite and arsenopyrite. The content of gold in the concentrates was 4-75 git. The roasting temperature was changed in the range of 773-l 173K, the consumption of calcined soda was 75-200% of stoichiometric necessarily for bonding of arsenic and sulphur into the water soluble compounds, the dura­tion of the process was varied in the range of 10-120 minutes. Under roasting in optimal conditions up to 97% of arsenic and 95% of sulphur go into water soluble compounds. The out­put of cake is 65-70% of the concentrates. The extraction of gold from the cake is higher than from the raw concentrates. The technology has been tested on a pilot plant scale

Jan 1, 1996

The Colorado Joint Review Process (JRP), a bold step to expedite energy and mineral projects, is off and running. Blazing the trail is Amax Inc., which serve as guinea pig in JRP's development and is now test-flying the process at its Mt. Emmons molybdenum property in Gunnison County, CO. Although JRP is still in its infancy, the new permitting review process has drawn enthusiastic applause from across the resource spectrum: William K. Reilly, president of the Conservation Foundation, said JRP is "one of the most interesting projects I've seen" and called on environmentalists to monitor its progress "because it appears worthwhile." Stan Dempsey, vice president of Amax Inc., noted that of all the locales in which Amax operates, Colorado is "the only place where the complicated mine permitting scheme appears to work"-an achievement he attributes to JRP. Lynda Lee Brothers, the federal Energy Department's assistant deputy secretary of environment, reported that an extensive DOE search has not turned up "another single mechanism in all of government and private industry as good as JRP as a model for the proposed federal Energy Mobilization Board."

Jan 7, 1980

By L. Stas

The authors have been interested in stress measurements in the rock mass for a long time. This paper describes the development of new apparatus for stress measurements in a rock mass. The principle of stress measurement by this device is based on the relief method as applied on the conical shaped surface of the bottom of a borehole. The design started based on the experience of K. Sugawara and Y. Obara who have been using the compact conical borehole over-coring system (CCBO). The conical shape of the strain gauge probe CCBO makes the fixation of the probe in borehole easy and, also, makes the measurement of stress in independent directions possible. The principle of the measuring method, the preparation of the borehole, the design of the probe for continuous measurement of stress during the course of overcoring are described. Also, a simplified version of the probe for long term monitoring of stress variations in the rock mass by means of the inserted body method and the initial laboratory results and in-situ testing of the development sample are described. Additionally, testing was done regarding the possible glues in relationship to the creep effect for this case.

Jan 1, 2006

By K. S. Venkataraman

The physical properties of clay-water systems depend on the complicated system of forces between the clay particles themselves, and between the clay particles and the ions in the liquid phase. The kind and distribution of ions in, on, and between the clay particles and the size and the shape of the particles are the basic factors determining the macroscopic behavior of clay-water systems. Understanding the system requires a knowledge of the nature of the clay particles, their size, structure, composition, and surface properties, and of the manner in which they interact with ions [and molecules] in the surrounding liquid [or other medium]. The validity of Professor Brindley's words (Brindley, 1958), written three decades ago in the context of making pottery, whitewares, and electrical porcelains, transcends time, and the basic message is perhaps all the more important in the considerably expanded use of ceramics for structural, thermal, tribological, electronic, and other applications. Silicon carbide, silicon nitride, and sialons have been studied in the last two decades for high- temperature structural and tribological applications, particularly for using in internal combustion engines. Titanates, zirconates and niobates of barium, strontium and lead, have high dielectric constants, and are extensively used in the formulations for making capacitors. Hexagonal ferrites (molecular formula MO.6Fe2O3) are in use for making permanent magnets for fabricating miniature motors, and for assembling loud speakers, particle accelerators etc. Cubic ferrites such as magnesium-zinc ferrite and nickel-zinc ferrite are used as transformer cores, and for other high-frequency applications. In this context, Richerson's recent book (Richerson, 1984) on the general scope of traditional and technical ceramics is a good starting point for an overview of contemporary ceramics technology. Glasses are a whole class of amorphous materials used widely as sintering aids, and for making glass-bonded ceramics and glass-ceramic composites. Composites are yet another burgeoning field where two or more particulate components are used for improving the performance of ceramics. For all these applications, the inorganic starting materials are almost always submicron and near-micron powders. Understanding the powders' physicochemical properties, and their surface chemical interactions with the surrounding liquid/gaseous medium is-necessary for making reliable ceramic parts at competitive prices. Even though ceramics science and engineering has attained its separate identity in universities and the industry, ceramists themselves would concede that ceramics science is a cross-disciplinary field, having incorporated and assimilated within itself many principles from several apparently disjointed disciplines. Principles of material science, graduate-level physics and chemistry, polymer science, surface and colloid chemistry, transport phenomena, particle technology, unit operations commonly used in chemical engineering and mineral processing, and statistics and applied mathematics are integral part of any ceramics curriculum in universities. Added to this is the fact that all bench-scale successes in making ceramic parts are to be scaled-up for larger throughput operations. Understanding and applying process engineering principles of comminution, classification, drying, calcination, etc. then becomes essential. CERAMIC FORMING: Despite the diversity of the materials and processes, conceptually, the steps involved in making ceramic parts have remained the same over several decades: The different components for making the pan (usually one or more powders plus other forming and sintering additives) are proportioned and mixed thoroughly, and the well-mixed formulations are consolidated into desirable shapes known as "green bodies." Usually binders such as wax, clay, organic polymers and surfactants, whether dispersed or dissolved in a suitable liquid are used during mixing the batch for giving strength for the green bodies. In the dried green state, the inorganic powders typically occupy only 55 to 60% of the bulk volume of the body, depending on the particle size distributions of the powders and the forming history, with mostly inter- particle voids accounting for the rest of the void volume. SINTERING: The formed bodies are then fired in high- temperatures kilns/furnaces during which the parts are exposed to a predetermined temperature profile, and "soaked" for a certain duration at the final high temperatures, typically between 1200 K and 1900 K, and then cooled to room temperature. The gaseous atmosphere in the furnace is controlled (oxidizing, reducing, or inert) when necessary. During the initial stages of firing, volatile liquids evaporate, and during the intermediate temperatures between 400 and 600 K, the the organic polymeric additives pyrolize and oxidize into water vapor, CO, C02, and other gases. At still high temperature, the glasses, when present, soften, and simultaneously, the ceramic particles rearrange into a network of grains with definite grain boundaries so as to reduce the total interfacial free

Jan 1, 1990

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By Norbert Patzelt

Today the standard method for grinding ore is the wet process. This is mainly due to the fact that the downstream process is wet and considering the total circuit dry grinding is not the most eco­nomical method for the comminution of the ore. Presently in gold ore processing dry grinding is only applied in cases where whole ore roasting is required downstream from the milling plant or if organic carbonaceous matters and sulfides are the primary reasons for the refractoriness. Since dry ore can be fed to the roaster, a dry grinding mill can advantageously be applied. In cases where d1y grinding could be applied advantageously for instance if the ore contains water soluble material and wet grinding is not possible there are serious concerns prevailing within the industty against this technology due to several reasons. Besides of the aspects as discussed later in this paper, there are several plants in operation with little success and considerable operational prob­lems. The reasons for this often lie in the fact that the several com­ponents of such a plant are bought from independent sources with­out considering the system requirements. It is essential that the dry grinding plants require accurate design between drying, pneumatic transport and grinding of the ore in the circuit. This paper will address some of these concerns raised in the industiy from a mill vendor's view along with discussing the development for the selection and configuration of the various dty grinding circuits.

Jan 1, 1998

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By Victor S. Sazhin, Alexander Kostenko

The hydrochemical method, which is based on the separation of aluminium oxide and silicon oxide by the hydrothermal decomposition of aluminosilicates by alkaline solutions in the presence of calcium oxide, can be effectively used for the complex processing of high-silicon aluminium ores. In this case, the silica is bound to a slightly soluble compound: Na20.2Ca0.2Si02•H20 (under the conditions: [&k]= 9, CaO/SiO2 = 1.05, alkali concentration in the solution: over 300 g/l Na20, T = 240...300 °C). If alkaline solutions of 100...150 g/l Na20 concentration are used, Ca0•SiO2•H20 or 2Ca0•Si02.0.5H20 compounds, depending on calcium oxide dosage, are formed at 280...320 °C. New methods for the crystallization of Na20.Al203.2.5H2O from concentrated alkaline solutions rand low-concentration solutions are proposed to isolate aluminium from solutions. The hydrochemical method, which involves no sintering process allows one to decrease the expenditure of heat by a factor of two, to reduce the investment and to exclude the pollution of the ambient air by dust-laden gases. The expansion of the raw-material resources base of

Jan 1, 1984

By P. Zhu

The leaching behavior of copper powders recovered from waste printed circuit boards (WPCBs) was investigated using electrogenerated chlorine and aeration in a sulfuric acid solution with added NaCl and CuSO4. Various parameters were studied to understand the mechanism of the copper leaching. When the current density increased from 0 to 0.1 A/cm2, the temperature from 30 to 60° C, agitation speed from 100 to 400 rpm, and the size ranged from below 75 to 150 µm, the leaching ratios of copper powders increased. The leaching kinetics were analyzed using a shrinking core model: 1-(1-X)1/3 = kt, and the leaching process was chemically controlled with an activation energy of 14.7 kJ/mol due to Cl- ion catalysis. The ratios of [Cu+]/[Cu2+] at various temperatures (30, 40, 50, 60 and 70° C) showed a periodic variation with the increasing of the leaching time. The redox potentials of the leaching solution and copper leaching ratios in different conditions were measured. The result indicates that dissolved oxygen achieved the dissolution of coppers and electrogenerated chlorine can promote the dissolution of copper powders and improve the reaction rate of kinetics in the presence of oxygen.

By Dewa Putu Agus Sudarmaja, Widi Astuti, Januarti Jaya Eka Putri, Yayat Iman Supriyatna, Himawan Tri Bayu Murti Petrus, Siti Nurul Aisyiyah Jenie, Ferian Anggara, Anisa Maulidia, Vincent Sutresno Hadi Sujoto, Sutijan, Wayan Warmada

With the rapid development of renewable energy technology, such as electricity reserves to store energy for electric and battery-electric vehicles, environmentally friendly energy sources are expected to continue to be tapped to meet mobility and stationary energy needs. Lithium is the most attractive candidate for energy storage development. The presence of lithium in the Sidoarjo mud in Indonesia makes it interesting for use as an alternative source of raw material. In this research work, sulfuric acid was used as a solvent, and hydrogen peroxide as an oxidation agent. Lithium recovery was studied with a leaching process at various temperatures (30, 45 and 60 °C) and sulfuric acid concentrations (0.5, 1, 2, 3, 4 and 6 mol/L). Increases in temperature, sulfuric acid concentration and hydrogen peroxide concentration were found to directly affect the lithium recovery. An increase in sulfuric acid concentration is directly proportional to the recovery of lithium in the solution. Optimum conditions were obtained at a sulfuric acid concentration of 6 mol/L and temperature of 60 °C. The shrinking core model was used to study leaching kinetics, and ash layer diffusion acted as a rate-controlling process. The activation energy of the leaching process was found to be 38.90 kJ/mol.

Jun 1, 2024

By Y. Gonzalez

The reaction kinetics of sulfuric acid leaching of brass foundry flue dusts were studied. As received flue dusts were separated into two size fractions, a coarse fraction (median size 103.5 microns) and a fine fraction (median size 3.4 microns). Experiments were performed on both fractions al-though most results are reported for the coarse fraction. Leaching experiments were conducted in a stirred reactor to determine those factors which govern the kinetic response of the sys-tem. The kinetics were followed by determining the increase in the concentration of dissolved copper with time. The effects of temperature, concentration and oxygen partial pressure on the rate of copper dissolution were examined. In addition, reaction residues were examined by SEM, EDAX and X-ray analysis. An activation energy of 4.8 kcal/mole (20.08 kJ/mole) was calculated. The rate was found to be significantly dependent on oxygen partial pressure and acid concentration. The order of the reaction with respect to oxygen partial pressure and hydrogen ion concentration was approximately 1.50 and 0.37, respectively. Results indicate that the dissolution reaction is limited by diffusion and can be described by the following mathematical expression where ~ is fraction of copper extracted in time t

Jan 1, 1988

By R. A. Meyr, K. A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by the U.S.Congress. The U.S. Mining Safety and Health Administration subsequently released the Final Rule on Refuge Alternatives for Underground Coal Mines, which required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. The following paper documents the research that was performed on a structural wall to be used in conjunction with a breathable air system to create a refuge alternative. A 103.4-kPa (15-psi) safe haven polycarbonate wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics. The successful safe haven wall design was modeled for an actual underground coal mine environment using the explicit finite difference formulation program FLAC3D to determine the responses of the wall and surrounding strata within a mine. A full-scale design was fabricated and installed in an underground coal mine to determine any construction constraints and as a final step in proof of concept for the safe haven wall design. This paper is meant to introduce the reader to a new wall concept to be used in conjunction with current technology.

Jan 1, 2013

By James P. Connell

The Montana Operations of the Anaconda Company constitute an integrated, though geographically separated, non-ferrous metal production complex. The mines are located at Butte and consist of one large open-pit mine, two small underground mines, a precipitation plant for both underground and pit-dump leach water, and the Weed Copper Concentrator. The smelter, located at Anaconda, Montana 25 miles to the west, processes all Butte copper shipments as well as copper materials from both Anaconda and private mines. Copper and zinc are refined at Great Falls, Montana, 165 miles to the north. Other facilities developed over the years include the Anaconda Forest Products Division, the Butte, Anaconda, and Little. Chicago Water Companies, and the Montana Hardware Company. Data processing for these operations has been performed on an IBM 360 Series, Model 30 computer, utilizing a Disc Operating System. This was replaced in September 1970 with a 360 Series, Model 40 128K unit. In addition, some data processing is also done for Anaconda Company operations located at Britannia Beach, British Columbia; Columbia Falls, Montana; Yerington, Nevada; and Twin Buttes and Tuscon, Arizona. The material under discussion in this paper will be concerned primarily with the mining operations at Butte.

Jan 1, 1970

By R. K. Mehta

An electrochemical coal oxidation model involving heterogeneous kinetics is presented. This model was tested by collecting current transient data on three coals assaying different ash content under varying operating conditions such as particle size, temperature, and % solids. In all cases, the model fitted the data very satisfactorily. Three intrinsic rate constants, namely mass transfer coefficient of Fe(II) Ions diffusing from solution to the anode (kma), mass transfer coefficient of Fe(II) Ions diffusing from solution to the coal surface (kmc), and chemical rate constant for coal oxidation with respect to Fe(III) at coal surface (k), were calculated. It was interesting to note that in this system, the mass transfer at anode was as important as the chemical reaction at the coal surface. The validity of this model was further demonstrated through a comparison of the activation energy of coal oxidation: firstly, by utilizing calculated chemical rate constant and assuming Arrhenius' type of relationship: secondly, by utilizing conventional approach using limiting current values. The comparison revealed that agreement was quite close. This kinetic analysis is useful because such a model can be used in predicting the intrinsic rate constants so that the relative importance of mass transport can be rationally analyzed.

Jan 1, 1991

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By Santhanam Sundaram

The potential for the utilization solar energy for the production of industrial process steer in mineral processing industries is discussed briefly. To advance the technical and economic feasibility of solar-thermal systems applications, U.S. Department of Energy has funded several projects. NL industries of Newberry Springs, California is one among them and has been chosen as a case study. The NL Industries solar system consists of 950 square meters of Del, single-axis, tracking, parabolic-trough, concentrating collectors. It was designee to produce a portion of the 420°. 530°k. steam utilized in a trying operation reduce the moisture content of hectorite ore from 10 percent to 4 percent. (Hectorite is an hydrous magnesium silicate which, when refined, is of significant commercial interest because of its applications in various chemical and food processes.) is estimated that implementation or this solar system could result an annual savings of 3.545 billion KJ ,3.360 billion BTUs), or the equivalent of 90 cubic meters (600 barrels) of oil and a net reduction of 1,860 kilograms (4100 pounds) of air pollutants annually. The technical, economic and institutional issues encountered in the course of this project are also discussed. Finally, the impact of the commercialization of solar energy applications in mineral processing industries is evaluated.

Jan 1, 1981

By W. C. Dailey

The National Steel Pellet Company is owned by National Steel Corporation, managed by the M. A. Hanna Company and located near the town of Keewatin in northern Minnesota. Annually, the concentrator processes 15.24-Mt (15.0 million It) crude taconite with eight 8.2-m diameter by 5.5-m long (27 ft x 18 ft) wet semi-autogenous (SAG) mills to produce 4.57-Mt (4.50 million It) of iron ore pellets. To improve operating costs and primary mill grinding circuit efficiencies, a task force on liners was formed with the operation, maintenance and engineering staff at N.S.P.C. along with the local supplier of mill liners. Results of the task force recommendations since 1980 along with improvements made in the primary circuit operations, are presented. Mill Liner Design and Metallurgy Changes The primary mill liner task force was formed in 1977. Its function was to improve the operating costs and milling efficiencies of the ten 8.2-m x 5.5-m (27 ft x 18 ft) wet SAG mills that were operating at the time. The SAG mills are driven by two 3500 HP motors drawing a total of 5450 kW at 76% of critical speed.

Jan 1, 1985

By George P. Demopoulos, Vladimiros G. Papangelakis, Dimitrios Filippou, A. J. Monhemius, G. W. Warren, E. Peters

A new method developed for the estimation of the activity of Ht in mixed sulfate solutions is described and examples of application of this method to the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3 from 298 to 473 K are offered. The method makes use of an "extended Debye-Hiickel" type of equation that was originally put forth by Das for pure H2SO4 solutions at ambient temperature. The treatment of mixed sulfate solutions was made possible by combining that equation of Das with a speciation algorithm which calculates the abundance of all species formed. The developed method, which also takes into account ionic strength and temperature effects, was used to generate hydrogen ion activity and speciation data for all possible acid/metal sulfate pairs of the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3. Finally, under the light of the reported data, specific examples of hydrometallurgical reaction systems are analyzed in terms of thermodynamics or kinetics. In particular, the systems discussed are: hydrometallurgical precipitation of hematite, solvent extraction of Fe(III), acid leaching of zinc ferrite, and oxidation of Fe(II) to Fe(III) by O2(aq).

Jan 1, 1993