Search Documents

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By R. W. Brann, R. C. Freas

Franklin Industrial Minerals operates several mines/quarries, including two room and pillar underground mines. Both of these mines are operated as multiple level room and pillar including heading and bench operations on one or both of the levels. This paper focuses on Franklin’s Crab Orchard, Tennessee mine, which produces both high purity chemical grade limestone and crushed stone for construction applications. The high purity chemical specifications for the chemical grade limestone and filler/extender applications are inconsistent with the non-chemical rock being produced to supply the crushed stone market. As a consequence Franklin has developed a unique mine plan and operation to maintain both product balance and a safe and stable working environment.

Jan 1, 2003

By Michael Traylor, Michael Jatczak, Brett Robinson

The Detroit River Outfall No. 2. is an effluent water conveyance system linking the Detroit Metropolitan Wastewater Treatment Plant to the Detroit River. The 6.4m (21ft) finished diameter tunnel extends 1,890m (6,200ft) east from the bottom of a 91m(300ft) deep, 9.2m (30ft) diameter drop shaft. At the eastern terminus of the tunnel, six Riser Shafts connect the tunnel to diffuser heads on the riverbed. The tunnel runs through a highly fractured Limestone formation capable of producing high levels of groundwater in?ows and Hydrogen Sul?de gas. Control of this water and gas was a theme which ran through the entire Project’s design and construction. This paper will provide an overview of each portion of the Project’s construction, including the Entrance Shaft, Precast Concrete Segments, TBM Tunnel, Pre-Excavation Grouting Methods, and the Riser Shafts.

Jan 1, 2003

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By James R. Arnold, John O. Marsden

Introduction Metallurgical accounting practices have been revolutionized over the past 15 years by the introduction of low cost personal computers and easy- to-use spreadsheet software. The Chimney Creek metallurgical accounting system takes full advantage of these advances. Data is provided by a PLC-based process control system, IBM data logging, operator logsheets and assay results from an automatatic plant sampling system. The data is organized and stored in an IBM PS/2 system using Lotus 123 and customized accounting programs to provide a comprehensive information management system. Metallurgical accounting for gold plants should ideally provide information for the following: a) Gold production accounting b) Day-to-day process control and operation c) Metallurgical evaluation and process optimization The Chimney Creek system provides all of these while overcoming specific accounting problems presented by SAG milling a coarse feed, grinding in cyanide and dump leaching run-of-mine material. Process description Gold Fields' Chimney Creek mine is located 47 miles northeast of Winnemucca, Nevada, at the northern end of the Osgood Mountains. Ore is processed by a combination of dump leaching and milling processes. The dump leach operation treats approximately 2.0 million tons per year of low grade ore (0.030 oz/ton). Run-of-mine ore is top dumped in 40 foot high pads. The use of three solution ponds for leaching enables an intermediate solution to be recirculated to the leach pad to reduce the pregnant solution flowrate and increase gold tenor of solution to the carbon-in-column (CIC) recovery circuit. Gold recovery is approximately 65% by this method. The milling process employs a SAG mill-ball mill grinding circuit to treat 900,000 tons per year at an average grade of 0.19 oz/ton. The ore is crushed to minus 12" in a jaw crusher prior to feeding the SAG mill. Cyanide is added to the grinding circuit to start gold dissolution as early as possible. After grinding, leaching of the ore is continued in a unique two-stage counter current decantation circuit 1 with 12 hours of leaching between stages . 85% of the soluble gold is recovered from the first stage thickener overflow in carbon columns (CIC). The second stage underflow is treated in a scavenger carbon-in-pulp (CIP) plant. Ultimate gold recovery is over 95%. Loaded carbon from both the dump leaching and milling processes is pressure stripped by hot cyanide solution and gold is recovered from the resulting solution by zinc precipitation. The precipitate is retorted for mercury removal and smelted into bullion. The plant flowsheet appears in Figure 1. Data collection Data for daily metallurgical accounting is obtained from three sources: a) Plant sampling b) Process control system c) Operator logsheets All of the data collection for metallurgical accounting is based around the 12-hour shift operating schedule. Sampling All critical sampling for gold production accounting is performed by automatic samplers (Figure 2). Heath & Sherwood two-stage sampling systems are used for sampling all slurry streams (cyclone overflow, CIP feed and CIP tails). The automatic sampler consists of a pneumatically operated primary sample cutter and a continuous rotary secondary splitter. The cyclone overflow and CIP tails are the most critical samples since these are used to calculate gold into and out of the plant on a shiftly basis. The CIP feed sample gives additional information concerning intermediate dissolution and recovery

Jan 1, 1990

Jan 1, 1998

By Gh. Crutu

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils and waters, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra).

Jan 1, 2008

By Gerald C. Smith

Carlin Gold Mining Company is a wholly owned subsidiary of Newmont Mining Corporation and is located 76 kilometers north west of Elko, Nevada. Multiple bench open pit mining methods are being used to mine 24.5 Mt of ore and waste per year. Mining started in 1964 and up through 1983 Carlin has mined 138 Mt of ore and waste and has milled 13.8 Mt of ore. Selective mining of carbonaceous and oxide ores together with a good grade control program have been key factors in the success of the operation. This paper will present the raining methods and the mining equipment being utilized to make Carlin Gold Mining Company a very profitable operation while mining and milling low-grade gold ore.

Jan 1, 1985

By James H. Harmon

As the trend to deeper mines, producing from marginal ore bodies, continues, mine hoists and their associated equipment will become more sophisticated, complex, large and expensive. Over the past two decades, mine hoisting equipment and systems have moved from steam engines to static rectification of ac to dc, and electronic controls are the standard. It is the intent of this section to present what is currently available in the field of mine hoisting equipment and systems. Because the present engineer has been exposed longer and more intensively to such things as computers, electronic devices, and machine design, no attempt has been made to make this a layman's article. Contributions from the electrical design and application engineer, gearing and hearing design engineers and other specialists have been incorporated. Some material will be devoted to electrical drive systems, rectifiers and gearing design among others. These items are inherent in the design of a mine hoisting system and the subsequent selection of the correct, most reliable and most economic system. The mine hoist can be a bottleneck between the underground mine and the surface mill. Correct selection of the right type of hoist is imperative. In this vital link between mine and mill, crude estimates of hoist capacity are not good enough, and the mining engineer must design and select the right hoisting system to meet the design specifications. 15.1-MINE HOIST TYPES There are two basic types of mine hoists available anywhere in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Drum and friction hoists are "generic" terms which describe the two basic categories. Within each category are variations, as below. 15.1.1-DRUM HOISTS Drum hoists, as noted, actually store the hoist rope on the drum much the same as line on a fishing reel. To accomplish this task, the drums are so designed to store, in one or more layers, the footage of wire rope equal to the total maximum hoisting distance plus sufficient rope for cutting and inspection at regular intervals and for holding to the drum (see Fig. 15-1). Usual practice in hoist drum design is to allow three turns of hoist rope for holding on the drum and three turns for inspection cuttings. 1. Single-Drum Hoists-Fig. 15-2 shows a typical single-drum hoist as manufactured by most U.S. heavy-mining-equipment companies. With the exception of some very minor features, this design configuration is standard throughout the U.S.A. Fig. 15-3 is a plan view of a typical single-drum mine hoist. This particular hoist has a single-motor drive and a double-reduction set of gearing.

Jan 1, 1973

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine or the expansion of an existing mine can range from nine to 24 months, or even longer. The time frame will vary depending on whether an environmental assessment (EA) or an environmental impact statement (EIS) will be completed Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. In this paper, a two-year natural resource baseline study by Homestake Mining for the Ruby Hill Mine, Eureka County, NV, is used as a case study to describe how a properly designed and executed natural resource baseline study streamlined the NEPA process.

Jan 1, 2003

By K. W. Morris

Of the fossil fuels used for power generation coal is by far the most variable and complex in its properties. A thorough review of the characteristics of the coal to be fired is essential before boiler design can begin. Major parameters such as heating value, moisture content and ash properties will determine not only the boiler size and configuration, but also the performance of the unit with respect to the thermal efficiency, particulate and gaseous emissions, and unit availability and reliability. An example of a review completed on a large low-rank coal deposit for a power plant will be described.

Jan 1, 1983

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By George L. Atwood

The western phosphate field, one of the United States' great mineral resources, lies within the western states of Idaho, Utah, Wyoming and Montana. This Permian sedimentary deposit has been known since the turn of the century and since the 1920's has been mined for its phosphate content. Isolation from markets and relatively high mining costs have restricted development as compared to eastern United States deposits, but nevertheless a significant western phosphate industry has developed. Geographically the deposit covers an enormous area of about 337 000 km2 (130 000 sq miles). It covers Idaho from Pocatello east- ward, western Wyoming to the eastern flank of the Wind River mountains, and extends well into southwestern Montana and into a large area of northeastern Utah north of the Uinta Basin and east of the Salt Lake valley.

Jan 1, 1983

By K. M. O’Connor

Time Domain Reflectometry (TDR) is a pulse testing technique developed by the telecommunications and power industry for use in locating breaks in cables. Variations of this principle have been utilized in applications pertinent to closure and reclamation of coal operations. This paper focuses on applications of TDR technology in the mining industry including monitoring of slope movement, abandoned mine subsidence, ground water levels and subsurface LNAPLs, landfill cover performance, and consolidation of mine tailings. TDR technology has been particularly effective for remote automated monitoring, and alarm systems have been implemented for monitoring subsidence.

Jan 1, 2003

By Thomas P. Meloy

Comminution is an old art. Unfortunately the analysis of the unit operations has been handicapped by the lack of both theoretical and experimental information. Two types of infor¬mation are needed, one an understanding of what happens when a particle breaks in a brittle manner; and two, an understanding of what happens when the daughter fragments pass through the mill. This paper is concerned with the former, the catastrophic fracture of a brittle solid. Recently, successful theoretical attacks on the frac¬ture of brittle solids have yielded significant-results. New experimental techniques are yielding insight into the physical phenomenon occurring during brittle fracture. Many of the re¬doubtable shiboliths of the last century are either being laid to rest or verified.

Jan 1, 1965

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By John J. Dwyer

As one begins to contemplate the organization of a talk with the title "Iron Ore - The Permanent State of Evolution," the main divisions appear to be the past, the present, and the future. But distaste for repetition of the present production achievements, which scarcely need additional description on this occasion, soon leads one to the conclusion that a more appropriate division of the subject is simply the past and the future . . . with emphasis on the future. We are working in the present, but it can only be understood by what has taken place in the years and decades gone by, and/or under what terms we will have to face the future. Evolution is more often thought of as a steady change - but steady change is really the product of revolutions, sometimes making headlines but often unnoticed at the time. With hindsight, we recognize the great importance of the emergence of the Bessemer converter and the open hearth and the vast influence that both have had on steel making and the changing ore demand. In this country we also see schooners opening the era for lake transportation of iron ore from Michigan to Take Erie. Later, steamships haul the ore from the Mesabi Range to the steel centers of the country. In order to take full advantage of the inland seaway, there had to be revolutions in ship design, loading and unloading facilities and channel and lock development. Full scale utilization of the resources of the Mesabi Range, itself, required parallel upheavals such as the development of new production equipment, and substitution of modern forms of energy for horsepower, and, yes, manpower, as well.

Jan 1, 1968

By Michael J. Cruickshank

MICHAEL J. CRUICKSHANK SENIOR AUTHOR Marine mining is a very broad field. It encompasses every facet of terrestrial mining but with the unique addition of a superimposed liquid overburden, which is itself mineralized. It is the unique aspects of marine mining that are discussed in this section. In keeping with the times, a systems approach is taken in the presentation of the material. The environment is first described, and this is followed in logical sequence by the common requirements for working there, then the mineral exploration phase, the exploitation and, finally, the operational restraints imposed by man and nature. Free use is made of tables and figures from original and published works and extensive listings of reference material round out each section. The title "Marine Mining" was chosen in preference to ocean or underwater mining because it is broad enough to include oceans, beaches and inland seas. The selection of terms sometimes may seem odd but they have not been chosen arbitrarily. All things are reduced, where possible, to basics and defined. Applying systems terminology, the word "platforms" is used in the functional sense and includes not only airborne, waterborne and fixed platforms, but man himself in his capacity as a working diver. If there is confusion it is often because of familiarity with a word in a context personal to the reader. For example, what does extraction mean to you-or mining or exploitation? Cost data have been interspersed throughout the section whenever they could be obtained. The use of these data should be tempered with understanding because no two situations are alike and improvements in marine technology are constantly being made. The names of individual authors are listed with each subsection. Where no name is given, the responsibility has been that of the senior author. Acknowledgment is sincerely made to the U.S. Bureau of Mines, and latterly the National Oceanic and Atmospheric Administration, for encouraging and supporting the preparation of the work ; to the secretarial staff at the Marine Minerals Technology Center and to Donald Eisman for editing. To the many other contributors who may not be listed by name, grateful acknowledgment is also due. It is hoped that the chapter will be useful to the practicing mining engineer who suddenly is assigned to marine work or to the experienced marine engineer who is equally suddenly assigned to mining work. It is not possible to put "everything-you -need-to¬-know" into one section, but. the very full bibliographies at the end of the text should adequately fill in for those who wish to know more. 20.1-THE MARINE ENVIRONMENT Marine mining is set apart as a separate discipline by the marine environment. The following subsections describe the environment from the point of view of the physicist, the chemist and the geologist. The interrelationship of these disciplines with the economic mineral potential of the oceans and seas is apparent from the description of the marine mineral resources. The marine environment is an extremely complex natural phenomenon with which the marine mining engineer must learn to live. It can be the source of his wealth or his frustrations and sometimes both. It can never be ignored.

Jan 1, 1973