Search Documents

By D. A. Ellis

This paper review s several new applications of solvent extraction developed in conjunction with a research project carried out under the AEC Raw Materials Division by the Dow Western Division laboratories during the last two years. A process for recovery of uranium from ores by contacting the solid directly with organic solvent without a prior aqueous leach and a process for uranium recovery by contacting thick, unfiltered leach slurry with the solvent were studied in an attempt to simplify ad reduce the cost of ore treatment procedures. Processes to produce pure UF4 products at the concentrate mills thus eliminating the production and subsequent dissolution of the concentrate were investigated. Since many of the leach liquors contained vanadium as well as uranium, solvent extraction processes for by-product vanadium were also studied.

Jan 1, 1958

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By William H. Breeding

The remarks that follow are based substan¬tially on experience covering 45 years, 80% of which have been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more-difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1 ½ . The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present.

Jan 1, 1984

By W. –E. Marx, M. Faber, R. Pollak, I. Astberg

INTRODUCTION Essentially three strategies are pursued in parallel for protecting the underground working force in mining against the consequences of methane ignitions which might lead to explosions: • Sufficient ventilation for avoiding the formation of explosive methane-air mixtures. • Avoiding sources of ignition caused possibly by electrical equipment or friction. • Structural explosion protection for limiting explosion propagation to the farthest-going extent for the case that methane is fired because of failing of the above preventive measures taken. The corresponding methods taken in mechanized roadheadings with point-attack roadheaders in German coalmining are subject of this paper. VENTILATION In ventilation of roadheading sites the following is to be considered in respect of methane control: • Sufficient air flows by volume being cycled to the heading face for diluting released methane to safe concentrations. • Sufficient local air velocities for effective mixing of methane and air in the whole heading site, in particular directly on the heading face and underneath the roof. Furthermore, ventilation needs to be laid out in a way that cut- ting does not result in health affecting dust exposure at any working place. Accordingly, the ventilation systems shown on Fig. 1 including primary and, if necessary, secondary auxiliary ventilation air ducts as well as dedusters, are used in roadheadings. This equipment is run according to the following principles: • If the roadheader is at standstill, the heading face is ventilated by the free air jet from the blowing duct closest to the face. In this operation phase the deduster is shut-down. • During cutting, the exhaust of the blowing air duct is automatically closed, and the deduster is taken into operation. The in- coming fresh air is now locally discharged via a lateral orifice, or distributed by Coanda-type ducts from the primary or secondary ventilation air duct. In this way, a stable dust wall not disturbed by the jet of the air duct is formed in front of the heading face. Only the ventilation air stream taken in by suction of the close-to-face deduster is passed through the inby zone of the heading face (over approx. 20 m). The clean exhaust of the deduster is dischayed to the roadway in some distance outby. Immediately at the heading face, methane accumulations possibly released by cutting are diluted by compressed-air jets from air-movers located near the roof which assure more rapid motion of the air without distuhing the dust wall. • In the zone of overlapping of primary and secondary duct and the deduster - that zone possibly is poorly ventilated during cutting - sufficient local air speed is assured by Coanda-type ducts or additional ventilation jets for avoiding methane accumulation. The regulations of the inspectorate specifies geometrical conditions to be met with these configurations of ventilation equipment. In-seam roadways are ventilated at rates > 0,5 m/s. For dedusters, present-day ventilation air flows are of 600-800 m+/ min. Ventilation monitoring and control is assured by units for measuring methane and ventilation air flows. If pre-set thresholds are exceeded or fallen short of, these measuring units shut-down - dependent on potential hazard - any not intrinsically safe electrical equipment in the roadheading, either totally or in limited zones. In addition, CO-measuring units near the roadway en- trance serve for early detection of mine fires. In spite of this ventilation layout and the equipment used and in spite of the water spray systems on the cutting head (discussed later in this paper) several cases of methane ignition and subsequent burning off (however, no explosions) have been recorded in the recent past. Therefore, the above-described ventilation is nowadays complemented in many cases by machine-mounted ventilation equipment for the immediate surroundings of the cutting head. Ventilation of the surroundings of the cutting head Investigations carried out subsequent to the above-mentioned gas ignitions have shown that the high ventilation air speed necessary for rapid dilution of methane could not permanently be arrived at in the following zones: • The direct zone of cutting, in particular during sumping. • The floor zone above the debris, predominantly below the cut- ting head. Accordingly, VOEST ALPINE-Bergtechnik, a producer of mining machinery, in cooperation with DMT developed for point- alttack roadheaders a novel machine-mounted ventilation equipment, the Jet-Block" (AERO SAFE Jet-Block) shown on Fig. 2. This system allows to ventilate the above-mentioned critical zones with high flow speeds. One AS Jet-Block is mounted on each side of the boom approx. 0.5 m behind the cutting head. The blocks discharge compressed-air jets with high energy from 10 nozzles per block into the hazardous zones (Fig. 3). Two nozzles of each jet block are tangentially oriented toward the upper circumference of the cutting head, the others are arranged fan-like with orientation to the heading face underneath the cutting head and the debris. The nozzle array of the blocks as well as the com-

Jan 1, 1997

By Ed L. Schrader

Kaolin of the Georgia-south Carolina "Clay Belt" are used in a wide variety of filler and extender applications. Sane applications specifically require the performance enhancement delivered by incorporating kaolin into the product formulations. Other applications are less specific in requirements for an inert mineral filler. In order to be a feasible candidate for filling and extending, a mineral or mineral product must be generally inert (except where specific interaction with the filled medium is desired), inexpensive, easily handled and transported in a variety of forms, accessible to a broad segment of the desired market, and must exist in sufficiently large ore reserves as to assure production for many years. Of course, more precise requirements are necessary in specific applications of a prospective filler material.

Jan 1, 1985

By John C. Brower

Bolivia is nor a major gold producer but has produced continuously since pre Inca times. Production reached a peak in 1964 of about 4,000,000 grams and is currently about 1,000,000 grams. Production is mainly from the Tipuani River valley north of La Paz and is derived from Pleistocene basin fill: the Cangalli conglomerate and overlying terraces. Abandoned Pleistocene lake terraces south of La Paz in the Oruro area are another source of gold whose potential have not been realized. In both the Tipuani and Oruro areas, primitive hand methods are the principal means of production, with the exception of a single modern dredge. In spite of a long history of production, probably very little of the gold potential has been mined.

Jan 1, 1979

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010

By Ralph W. Barbaro

This paper presents a cyclic queueing model which evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumptions of exponentially distributed service times and steady-state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1986

By Edward F. Oxford

The area described in this paper lies along the inner margin of the Coastal' Plain in Twiggs County, near the exact center of the State of Georgia. Twiggs is one of four counties which produces approximately 75 per cent of the nationals output of kaolin used in the paper trade. In this vicinity the land surface is characterized by coastal plain hills with elevations ranging from about 250 feet, above mean sea level in the flood plain of: the Ocmulgee River to about 550 feet above mean sea level on the hill tops. Surface drainage in the area is southwestward to the Ocmulgee River, the tributaries of which have dissected the land surface exposing thick sections of the upper parts of the hills of Eocene (Ocala Limestone and Barnwell formation) limestone, sand, marl and clay, and in the lower parts of the hills Cretaceous (Tuscaloosa Formation) kaolin, kaolinitic clay, sandy clay, sand and, gravel. The contact between these two principal groups of geologic units is rather easil distinguished as the top of the kaolinitic beds. It is described in detail and mapped in published geologic reports for the area (LaMoreaux, 1946).

Jan 1, 1968

By Warren D. MacEvoy

INTRODUCTION Good ventilation bulkheads (stoppings) can be obtained only by conscientiously adhering to four basic principles: carefully selecting the site for the bulkhead, adequately preparing the site, properly constructing and sealing the bulkhead, and checking the results with a smoke tube before leaving the area. If all these guidelines are followed during each ventilation project, a poor job will result only from the use of improper materials and cannot be blamed on carelessness or oversight. SITE SELECTION A perfectly constructed bulkhead in the wrong location can be completely worthless. Conceivably, a bulk-head in the wrong location could cause dangerous ventilation conditions that are difficult to identify and isolate. If the suggestions herein are followed, a considerable amount of work, time, and material may be saved. Perhaps the single most important step is always to select the exact site for a bulkhead before starting construction. Although the latitude in selecting a site may be limited by instructions or operating conditions, it is common to find poor bulkheads built within a few meters (feet) of a site that would have been far superior but was overlooked during the planning process. The ideal site for a bulkhead should have as many of the following features and conditions as possible: 1) To provide a solid bulkhead, the selected site should be in firm and unbroken ground. 2) To minimize the amount of work and material required and to minimize the danger of later damage to the bulkhead, the site should have as small a cross section as possible. 3) The bulkhead site should not be encumbered by interferences such as pipes, wires, ditches, wire roof supports, trash, muck piles, etc. 4) The walls and timbers of the site should be free from oil, grease, or tar that would inhibit adhesion of the sealant used on the bulkhead. 5) Unless special precautions are taken, the site should not have water seepage, standing water on the floor, or water-carrying ditches. 6) To expedite construction of the bulkhead, the site should have reasonable access to transportation, supplies, communication facilities, and compressed-air lines. 7) The site should have a reasonably level floor, allowing direction of the bulkhead door swing to be reversed at a later time if so desired. In a steeply sloping location, it may be possible to open the door in one direction only. SITE PREPARATION Once a suitable site has been selected for the bulk¬head, it must be prepared properly. All site preparation work should be completed before starting any construction work on the stopping itself. Unfavorable site conditions can be identified during the course of thepreliminary site preparation, saving time, effort, and materials that otherwise might be wasted. The follow¬ing preparation steps help assure the construction of a good stopping: 1) If wire mesh has been used at the site, a strip 457 mm (18 in.) wide should be cut and removed from the walls and roof at the selected location. 2) The exposed strip of rock should be barred down thoroughly to provide a smooth surface. 3) All obstructing materials should be removed, including old timbers, pipes, rockbolts, wires, etc. If a conduit must cross the bulkhead area, it should be located or relocated away from the floor, walls, and roof to allow a 6.28-rad (360°) seal around the juncture between the conduit and the bulkhead structure. 4) All loose muck should be cleaned from the site and a trench about 152 mm (6 in.) deep should be dug from wall to wall in the floor. The trench must be wide enough to accommodate the entire bulkhead, including the posts. 5) The rock surfaces of the walls and roof should be cleaned with a wire brush to remove as much loose surface material as possible. Thorough cleaning promotes adhesion of the bulkhead sealant to the surfaces of the walls and roof, thus promoting an airtight seal. 6) It is quite difficult to seal landing mats that cross a bulkhead. If such a crossing cannot be avoided, the bulkhead should be placed between the end and the first hole in the steel so at least one side of the bulk-head can be sealed easily and completely. That may have to be done prior to actual construction if the end is located on the opposite face from the seal coating of the bulkhead. BULKHEAD CONSTRUCTION The three principal considerations in bulkhead con¬struction are the type of bulkhead, materials to be used, and construction method to be employed. For many projects, the bulkheads are specified by the requesting agency, with no latitude for independent choice of the type, materials, or construction method. In such cases, any deviations from the specifications, for any reason, must be approved in advance by the proper department or by the project senior ventilation engineer. Types and Materials When a choice of type, materials, or method is allowed, consideration should be given to factors such as cost, required useful life, proximity to blasting concus¬sions, availability of materials, direction of permissible air leakage, and degree of airtightness required. Other factors to be considered include the amount of time available, accessibility of transportation, potential for interference with operations or production, ambient water conditions, availability of connections to com¬pressed-air lines, etc. Despite the multitude of factors to be considered, most stoppings can be analyzed easily and the proper choices can be made without much difficulty. The four common classes of bulkheads utilized in

Jan 1, 1982

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud.INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1]."

Jan 1, 2018

By Thomas B. Faddies

The Trixie mine is located in the East Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1983

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud. INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1].

Jan 1, 2019

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By Rudolf Fahn

Bentonites are best suited for the preparation of acid activated clays with efficient adsorption properties. They are weathering products of acid volcanic ashes and their natural deposits are world-wide spread. The main constituent of bentonite is the aluminium hydrosilicate nontmorillonite with a high ability to swell. Süd-Chemie owns bentonite deposits in Germany and subsidiaries in Italy, Mexico and Arizona.

Jan 1, 1979

Miners really are an optimistic bunch. Even with the dark clouds hanging over the global industry, mining professionals still turn out in droves at industry conferences. In February, more than 7,200 professionals attended SME?s Annual Meeting in Denver, CO, a record. And the following week, more than 30,000 people converged on Toronto, ON, Canada for the Prospectors and Developers Association of Canada (PDAC) meeting. For many small and junior mining and exploration companies the PDAC conference is a place to find potential investors in their projects. The Investors Exchange attracts several hundred companies, each showing off their properties to the many money types who wander the hall during the four-day conference.

Jan 1, 2013

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

How does an investigation into the breakage characterization of electric arc furnace (EAF) manganese slags contribute to a more responsible usage of resources throughout the life cycle of steel products and reduction of carbon emissions? The main goal of this study is to increase the knowledge on the mechanical response of manganese slag to open the potential of pyrometallurgical residues to become secondary material in industrial applications such as infrastructure construction, fillers, binders and soil stabilization, among others.

Mar 1, 2024

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

Over the past 15 years, roof fall rates have decreased by two-thirds in U.S. coal mines and by even more in regions where the roof is weakest. This remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present an empirical design methodology that uses real-world data to quantify the basic roof-support concepts that have been successful in the United States. A new computer package, called Analysis of Mine Roof Support (AMRS), implements the design methodology.

By M. L. Free

Acid consumption in copper heap leaching is determined by the minerals present in the ore. Gangue minerals such as biotite and chlorite consume acid together with copper-bearing minerals such as chrysocolla and malachite. Acid consumption is affected by the rate of acid application and the particle size. Some gangue minerals undergo alterations and cause precipitate formation during acid leaching. Other minerals form due to precipitation as dissolved ion concentrations from a variety of mineral sources combine to exceed saturation levels. Copper recovery is related to all of these events. This study presents information on acid consumption of various gangue minerals as well as data for copper recovery from an associated copper ore.

Jan 1, 2010

By P. K. Songfack

The transport of slurry within the ball mill depends on the peripheral velocity and porosity of the ball charge. Residence time distribution and mill hold up are of-ten used as indicators of the mode of transport. In this work, the transport problem is tackled via direct simulation of the three dimensional motion of the ball charge. In doing so, the following quantities are calculated: (i) ball size distribution as a function of the distance from the feed end of the mill (ii) mean peripheral and longitudinal velocity and longitudinal velocity of balls of different sizes, and (iii) the spatial distribution of porosity within the ball charge. Hence, the problem of transport is handled as a motion of part of the slurry with the ball charge and part as hydrodynamic flow through the porous structure.

Jan 1, 1993