Search Documents

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By Jessica M. Wempen

"Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has application for monitoring subsidence with high resolution over short periods. DInSAR uses radar images to measure centimeter-level surface displacements. In the images, ground resolution can be relatively high, with each data point (pixel) representing the average displacement over an area of several square meters. The image data are acquired regularly which allows subsidence to be monitored sequentially over short periods; imaging periods typically range from weeks to months.Monitoring subsidence over short periods with high spatial resolution has potential to provide insight into the dynamics of subsidence and into relationships between mine advance and subsidence. In this study, for three longwall mines in the western United States, initial subsidence occurring at the start of longwall advance is quantified over short periods (12 to 72 days). C-band interferometric wide swath Synthetic Aperture Radar (SAR) images from the Sentinel satellites are used to quantify the subsidence. Overall, the data show initial development of subsidence, expansion of the subsidence trough, and the advance of subsidence in the direction of mining.INTRODUCTIONApplied Differential Interferometric Synthetic Aperture Radar (DInSAR)Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique that can be used to quantify small displacements of the Earth’s surface. Using data from the Seasat satellite, which was launched in 1978 (Jet Propulsion Laboratory, 2018), studies by Goldstein, Zebker, and Werner (1988) and by Gabriel, Goldstein, and Zebker (1989) applied Synthetic Aperture Radar (SAR) interferometry to topographic mapping and displacement monitoring. These studies established the potential for broader applications of radar interferometry. Studies by Foxall, Sweeney, and Walter (1998), Wright and Stow (1999), and Carnec and Delacourt (2000) represent some of the earliest evaluations of DInSAR for mine subsidence monitoring. All three of the studies demonstrated the application of DInSAR for quantifying mine subsidence. They also demonstrated difficulty accurately measuring subsidence over long periods due to data decorrelation. DInSAR continues to be evaluated as a tool to quantify surface deformation related to active and historic mining. For example, see Vervoort and Declercq (2018), Wempen and McCarter (2017a), Chen et al. (2013), and Liu et al. (2013). Technologies associated with SAR interferometry continue to develop. Recently launched satellites have relatively high spatial and temporal resolutions, and data processing methods and data accessibility are improving."

Jan 1, 2019

By Prashanta K. Chatterjee

The planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc, do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered. Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate many layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment.

Jan 1, 1986

By Yoshiaki Numata

It is a matter of importance to use the lower alkyl monoethers of propylene glycol (polyPGME) as a frother in sulfide mineral flotation, for their compounds are highly soluble in water and are surface active frothers to some extent. The purpose of this study is to clarify fundamental roles of frothers in sulfide mineral flotation by investigating the effects of polyPGME on the floatability of galena with xanthate and adsorption property those ethers at the liquid/air interface. Fundamental investigation on the flotation of sulfide minerals using o,o-dialkyl dithiophosphates has been carried out through galena floatability tests in the following two cases:(l)single use of dithiophosphate for sulfide mineral collection and (2) joint use of dithiophosphates for its collection.

Jan 1, 1991

By Carlos Fonseca, Gustavo Usero, Roberto Mentzingen Rolo, Gabriel Moreira, Octavio Rosa de Almeida Guimarães

Geological domain modeling is an important step in mineral resources evaluation. The procedure can be laborious and time-consuming, especially in multivariate settings. However, estimates are significantly improved when carefully limited by geological variables. This paper proposes a workflow for geological domain modeling suited for stratigraphic deposits. The workflow consists in automatically defining the domains by using clustering algorithms, generating the surfaces that represent the contacts by interpolation and subsequent triangulation, and simulating the surfaces. The proposed workflow produces consistent and realistic results and allows the user to test different domain configurations and assess volumetric uncertainty automatically and quickly.

Jun 25, 2023

By M. Duane Lackey

Electric drives hire done outstanding job in many-fields that are related to the mining industry. The equipment that is offered for electric-trucks was developed from the traction equipment which is used on the diesel electric locomotive. Rotating equipment available for use on electric trucks is identical in principle to that which is used on these locomotives. In as far as it is practical, similar controls are used. Another descendent of the diesel electric locomotive can be found in the oil well drilling industry, Here, locomotive traction motors and. electric controls have been modified to fit the particular requirements of the drilling industry, One 2400 H.P. diesel electric drilling rig drilled a 24,000 Ft. well in West Texas with an electrical maintenance cost in the order of 7¢ per hour This was a new rig and the costs are less than the average maintenance costs will be for the life of the equipment, Even soy since it took one (1) year to drill this well, this 7¢ per hour has real significance. Electric shovels use a similar type of electrical equipment; they too have shown real savings over the equipment they replaced. Since electric drives have done so well, in other fields, they warrant consideration for use in high horsepower, large capacity trucks.

Jan 1, 1961

By A. Jennings, J. Cornet, P. Perrone

Controlling long overland conveyors with multiple drive stations is a complex problem. The methods for controlling these belts in a steady state are well-covered in existing literature, but a discussion of starting and stopping strategies is absent. This paper outlines different control strategies for starting, stopping and running conveyors with multiple drive stations. To illustrate the benefits of applying the methods described in this paper, the authors show how their adoption corrected many of the control system problems at Essroc Cement’s overland conveyor, which features three drive stations separated from each other by long lengths of continuous conveyor belt.

Jan 1, 2013

By Otto Schumacher

Shortcut methods are commonly employed for estimating mining costs for prefeasibility studies. Most of these methods, however, are suitable for earliest stage studies or for internal discussion purposes only. The experts at InfoMine?s CostMine division recommend that any cost estimate completed for purposes of significant decisionmaking or for compliance with Canada?s NI 43-101 requirements be completed using a determinative itemized method. The same basic principles apply for an early stage, intermediate stage, or advanced stage estimate. The only difference is in the level of detail and effort employed. ? Based on the results of a completed resource estimate, an itemized cost estimate begins with development of a conceptual mine plan. Using a surface mine as an example, four elements are crucial no matter what level of study is initiated. Basic geometry of the ore deposit and waste material, with a determination of the expected ratio of waste to ore, a reasonable pit slope angle, possibly requiring the completion of geotechnical studies to predict the waste-to-ore ratio with certainty. ? Determination of the assumed ore and waste production rates. ? Locations of all ore stockpiles and waste dumps. ? Segmental haulage distances and gradients for ore and waste.

Oct 1, 2013

By Frank E. Kottlowski

Widespread high-calcium (HC) limestones in New Mexico and adjoining areas, are low in magnesium, but some units include shale interbeds that would be deleterious for usage in sulfur removal. In southwest New Mexico, southeast Arizona, and adjoining parts of Mexico, limestones in the thick Mississippian Escabrosa, Pennsylvanian-Permian Horquilla, and Cretaceous U-Bar units are HC as are strata in the Mississippian Lake Valley, Pennsylvanian formations, Permian Hueco, and parts of the Permian Capitan Limestone of south-central and southeast New Mexico and west Texas. In north-central and central New Mexico, many limestones in the Pennsylvanian Madera Formation are HC as are some of the Cenozoic travertines. In northwest New Mexico, where the present-day mine-mouth coal- fired power plants occur, there are no HC limestones, but to the north in southwest Colorado some beds of the Mississippian Leadville Limestone and Pennsylvanian Hermosa Formations are HC. HC limestones considered contain at least 95 percent calcium carbonate and less than 3 to 5 percent magnesium carbonate. Limits for other impurities are alumina, 1 percent; silica, 2 percent; sulfur 0.05 percent; phosphorous, 0.02 percent; and iron oxide, about 1 percent. Chemical and physical requirements differ slightly depending upon the ultimate use.

Jan 1, 1995

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By Maurice C. Fuerstenau

INTRODUCTION The term, chelate, from the Greek for 'claw,' has its origin in the pincer-like representation of more than one atom of a single ligand bonded to the same metal atom, forming a ring-like structure. Depending on how many attachments exist on the sphere of coordination around the metal ion, ligands are referred to as bidentate, tridentate, tetradentate, pentadentate and hexadentate According to Calvin and Martell (1952) and Somasundaran and Nagaraj (1984), chelating agents must contain suitable functional groups, and their location within the ligand molecule must enable ring formation that is sterically possible. Typical structures that meet these requirements have been given by Fuerstenau and Herrera-Urbina (1988) and are listed in Figure 1. As noted, the functional groups of these reagents contain electron donor atoms such as oxygen, nitrogen and sulfur. Basic groups, such as amino (-NH,), are those that contain an atom with a lone pair of electrons. Acid groups are those, such as carboxylic (-COOH) which lose a hydrogen ion and coordinate with the metal atom. Examples of each of these types chelating reagents are given in Tables 1-4. The specificity of chelating agents for various metal ions has long been known and was utilized early in the search for new flotation collectors. In 1927, Vivian used ammonium nitrosophenylhydroxylamine as a collector for cassiterite. Holman (1929) tested dimethylglyoxime as a collector for nickel oxide. He also suggested taurin as a collector for oxidized lead ores. DeWitt and von Batchelder (1939) suggested the use of oximes as flotation collectors. Gutzeit (1946) conducted an extensive investigation on the use of chelating agents as collectors and as depressants for gangue minerals. The depressants are those reagents that form soluble chelates with metal ions that could function as

Jan 1, 2005

By CORNELIUS STEPHANUS LODEWYK SCHUTTE, WIEHAN ADRIAAN PELSER, JEAN HERMAN VAN LAAR, MICHAEL DAVID HARMSE

Rising electricity costs in South Africa have resulted in a need for optimized compressed-air networks in the mining environment. As a result, the financial benefit of air receivers needs to be reconsidered along with the economic dispatch strategy. This study investigates the use of an evolutionary algorithm in the mining industry to determine the potential financial benefit for various-sized air receivers, as well as their dispatch strategy. A genetic algorithm was selected due to the improved solution reliability and accuracy compared to other optimization techniques. This study indicates that a genetic algorithm can be used to determine the optimal dispatch of compressed air in the deep-level mining industry. Further, this study indicates that air receivers are financially viable in the mining industry and can be used to reduce operating costs, improving profitability.

Dec 1, 2022

By Rolph Linder

It is generally known and accepted that the efficiency of the blast furnace process, expressed by the symbols specific production and coke consumption, is influenced by a large number of variables connected to the type of burden, the alloy contents of the produced iron and the conditions of production as composition and preheating of the blast, the furnace heat losses and the possible use of fuels added on the tuyere level. It is furthermore obvious, that the coke consumption of the process will be influenced by specific production which could be said to be the result of two counter-acting influences. With high production, realized through intensive blowing, the passage time of the ore through the furnace is shortened leading to a decrease of the indirect reduction taking place in the upper part of the shaft within the temperature range of 300 to 1000°C. Simultaneously the external heat losses (constant in time) will be smaller calculated on each ton of iron and the resulting change in coke consumption will be the effect of both those influences. It is certainly of interest to be able to predetermine the effect of those variables before a change in the production practice is carried out.

Jan 1, 1964

By Douglas M. Deason

Swelling clays, such as montmorillonite, contribute significantly to the poor dewatering and consolidation behavior of the Florida phosphate clay wastes. Understanding and to a degree, control of the forces which cause the swelling behavior may aid in supplying a solution to this problem. The technical feasibility of utilizing control- led dispersion for aiding dewatering of phosphatic slimes was investigated. This technique is based upon inhibition of swelling and self-dispersing tendencies of the montmorillonite clays by dispersing the solids in electrolyte solutions. Through this process, significant improvements in settling rates and sediment solids content were achieved in both pure clay systems and on simulated phosphate slimes.

Jan 1, 1983

By Eugene F. Casey

An immersed tube tunnel is one which is composed of elements that are prefabricated in a dry dock or on shipways, usually away from the actual tunnel site, floated into position and then lowered into a preexcavated and graded trench below a body of water. The elements or segments are then connected to each other under water, and the entire immersed tube tunnel covered with a protective blanket. Because water is essential, this method of construction offers advantages in a relatively limited field. By the very nature of the method, lowering elements to the bottom of an underwater trench, immersed tube tunnels are primarily used for crossing bodies of water, such as rivers, bays, straits, canals, etc. Although this method of construction was first used for a subaqueous railway crossing under the Detroit River in 1906-1910 and again in 1912-1915, for a four track subway tunnel under the Harlem River in New York, the reason immersed tube tunnels construction has not been used more extensively is simply a matter of economics. Bridges, compressed air tunnels and similar structures could be constructed at a lower cost.

Jan 1, 1970

By S. A. Braley

Water is our most important natural resource, for without it there is no life. It is also the principal natural resource for all manufacturing processes, in particular for the development of power. For these reasons it is essential that water be protected and conserved, with the realization that its quality 18 as important as the water itself. A significant factor in the quality of ground water is the mining of coal -- that other main ingredient of Power. In the mining of coal it is necessary to disturb the geological strata overlying or adjacent to the coal seam. This procedure not only releases water from water-bearing strata or underground aquifers but also exposes other minerals which eventually become the source of pollution or deterioration of the released water as well as of the surface stream into which It is discharged It is then evident that in attempting to utilize one essential natural resource there is degradation of the quality of the other. Many selfishly assume that the principal function of a stream is fishing and recreation, but the real function is the support of industry and agriculture upon which civilization is dependent.

Jan 1, 1959

By Devraj Sharma

This paper presents technical issues in the design and management of a retorted oil shale disposal site. Major physical and geochemical mechanisms which affect the disposal are: heat transport, moisture migration, chemical species transport, auto-ignition, and mechanical behavior alterations of the retorted oil shale pile. The interaction of these mechanisms and their relative magnitude will affect the environmental behavior of the pile. The paper discusses the coupling between the mechanisms, presents a framework to quantify the processes by laboratory and field measurements, and in addition discusses the use of mathematical models to provide quantitative predictions.

Jan 1, 1981

By H. Nazeri, T. G. Rozgonyi

Many industries when volumes of the solid materials are large invariably relay upon the gravity to induce solids to flow out of storage, through channels and reactors. In mining industry ore pass’s requirements to less energy (only gravity) have made them very popular both in underground and open pit mines. This paper discusses the major findings of research on 2D Discrete Element Method simulation of gravity flow of ore in ore passes. Results show that ore characteristics, ore pass configuration can significantly affect loads (static, dynamic) on the gate assembly and creation of hang-ups.

Jan 1, 2003

By L. D. Cruz

In Exxon's Los Bronces Expansion Project in Chile, a stochastic simulation is performed to resolve the complex decision problem of matching the mine to mill system capacities from both technical and economic standpoints. The unique combination of weather conditions at the mine and the 30-km belt conveyor network for ore transport to the mill necessitates this analysis in the planning phase to optimize the design capacity of the sys tem. Appropriate statistical distributions of major equipment performance, snow storm duration, power outage, etc, ate developed from actual mine local records and manufacturers specifications. The interactions of operational constraints including ore storage capacities, number and sizes of individual equipment, ore variations, and mine and mill production rates are studied more realistically than in a traditional planning approach. Details of the computer modeling and typical results of simulation studies are discussed.

Jan 1, 1981