Search Documents

By William N. Poundstone

Since World War II, when off-track mining became popular, mining machinery has undergone much change. However, the change has been basically to make the machines more powerful, more productive and more reliable. Little change has been made, in this period, in the basic mining system. While steady improvement was made in productivity until the passage of the new Federal Coal Mine Health & Safety Act, I believe that the cost Co benefit ratio of further improvement from this basic approach of improving the existing extractive tool is not as promising as I believe may be obtained from a new approach. Consequently, six years ago Conoco and Consol undertook a comprehensive long-range R&D program to see if improvements of a more basic nature could be made in underground mining. We concluded early in our program that while many things currently limit the rate of production such as the rate at which roof can be supported, time needed to advance ventilation systems, time required to clean up and rock dust, time required to maintain and service equipment as well as time lost due to haulage deficiencies, that the key to improvement was a truly flexible continuous high capacity haulage. With face equipment in use today, mining rates can be increased with such a haulage system where the ability to support the roof exceeds the ability of conventional haulage equipment to remove the coal. More importantly, if we could develop such a system, it would set the stage for development of far more sophisticated methods of mining at the face than exist today, and as new and more dependable mining machines and methods are developed, continuous transportation will enable the gains envisaged in production to be realized.

Jan 1, 1974

By Malcolm J. Robinson

Over 80% of Australia's population lives within 200 km of the coast, 70% in 10 major coastal cities. Potential cement raw materials are widely distributed but deposit size, quality, transport, market and environmental considerations are important in determining economic value. Major production locations are in a variety of geological environments ranging from Lower Paleozoic crystalline limestones to Tertiary and Recent polyzoal limestones and limesands, both onshore and offshore. Raw material transportation is by road, rail, sea, aerial ropeway and pipeline; road/rail transportation of the finished product is traditional but movement by sea of clinker and cement is increasingly a feature of the industry.

Jan 1, 1982

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By James Westfield

I welcome this opportunity to appear before you and to review briefly the various health and safety services of the Bureau of Mines available to the mining industry, other than coal, and also to tell of our plans for extending these services to improve safety and health conditions. The Bureau's health and safety activities are basically services by which we attempt to develop and disseminate information on improved techniques in mine accident prevention and promote mine safety education in the mineral industries. Unfortunately, some mining companies, particularly some of the smaller operations, seem to be unfamiliar with these services, The Bureau of Mines is charged by law with the responsibility for inspecting coal mines; other services to the coal mining industry and are provided only on request, Safety inspections and other services that we offer are provided for noncoal mining industries solely upon request.

Jan 1, 1958

By Myles E. Altimus

One responsibility of a manager is to improve his human organization. Some executives believe a manager should be measured and compensated accordingly on the basis of his ability to improve the quality of his human organization. Officials in the coal mining industry have had a tough road to travel in this regard due to fluctuating coal production demands, contractual obligations, and improved mining equipment and methods. The time may have finally arrived when we are able to recruit, select, and develop men from the labor market to fill vacancies, This is particularly true of our maintenance organizations. Because of the importance of this responsible function and the types of skills required, we must develop an extensive improvement pro- gram. Anyone in the industry who fails to undertake a manpower audit and who accepts a philosophy which will not permit collective planning, organizing and con- trolling the improvement of the human element throughout his maintenance organization may certainly cause deterioration within his company.

Jan 1, 1966

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil Corp. (now part of Atlantic Richfield Co.) in the period 1.965 to 1968. The results of the work show that presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. This has implications for several types of retorts. Correlation of the results of this work with that of other investigators shows that the partial pressure of retorting products in contact with oil shale during retorting has an effect on yield. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to await commercialization of another process. The existence of a plant in which to test prototype size would markedly reduce such development costs. Results Preliminary development work with the apparatus was carried out using a fluidized bed of sand, as explained later, with the entire system brought up to temperature and flows stabilized. The shale was injected rapidly in a slug (batch) which had small mass compared to that of the high temperature system to make the reaction approach isothermality with reasonable approximation of instantaneous preheating. Typically, the temperature in the center of the bed dropped from 900°F to 600°F one minute after batch addition. It returned to 750' within three minutes and 900° within seven minutes. Obviously, the bed was quenched but it recovered rapidly. Average bed temperatures of 700' to 1020°F were examined to compare the effect of temperature with published results. Yields In the 700°F range were only 10 to 15%, of Fischer Assay (FA). Above about 950'F, oil yields decreased and gas yields increased. Nitrogen was used first as the fluidizing gas to provide a chemically inert medium. Incept for an insignificant dip at 895"F, Figure 1, oil yield was not affected by retorting temperature in the 800° to 900' range as long as residence time was adequate (16 minutes). At 925°F, the oil yield was some 103% FA. With further increase in temperature, the yield decreased to 86% FA at 1015°F. There is no increase in carbon on spent shale, the lost oil goes to Increased gas make.

Jan 1, 1972

By G. A. Rosario, G. Peach

Twin 8.5 m diameter, 10 km long headrace tunnels under overburdens of up to 1870 m were excavated for the neelum jhelum hydroelectric project in north-eastern pakistan using two main beam gripper tunnel boring machines (tbms). Rock bursts were encountered and presented a significant danger to personnel and equipment. Micro seismic monitoring was installed to analyze rock burst characteristics and to create a database for future reference. Correlation of rock burst characteristics improved the ability to predict the likelihood, location, severity, and number of rock burst events. This paper presents the analysis of the micro seismic data

Dec 1, 2022

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By L. Zhou, D. Bahrami, Y. Xue

Underground mine fires are a threat to the safety and health of mine workers. The timely determination of the location and size of an underground fire is of great importance in developing firefighting strategies and reducing the risk of any injuries. Machine learning was used in this paper to develop a predictive model for fire location and fire size in an underground mine. The ventilation data were obtained by simulating different mine fire scenarios with MFire. The ventilation data of all airways were used as features to predict the fire location. Based on the feature importance, five airways were selected to monitor, and the airflow data of the selected airways were used to predict the fire location and fire size. An accuracy score of 0.920 was obtained for the prediction of fire location. In addition, in-depth analyses were conducted to characterize the wrong predictions with the purpose of improving the performance of the random forest model. The results show that the occurrence of fire at closely connected airways at some locations can generate misleading ventilation data for each other and the model performance can be further improved by grouping them. Fire size is another factor affecting the model performance and the model accuracy increases with increasing fire size. The result from this study can help mine safety personnel make informed decisions during a mine fire emergency.

Mar 2, 2022

By Bo Hyun Kim, Mark K. Larson

This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock-mass behavior in longwall coal mines in highly stressed, bump-prone ground. The floor-heave and nofloor- heave phenomena at a western US coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria (i.e., Mohr–Coulomb or Hoek–Brown failure criterion). The previous numerical study demonstrated these phenomena using a user-defined model of the s-shaped brittle failure criterion in conjunction with a spalling process in the FLAC3D numerical modeling software. The results of the FLAC3D modeling agreed with the observations of the relative amounts of heave from each gate-road system. However, the FLAC3D model adopted many assumptions and simplifications that were not very realistic from a physical or mechanical perspective. To overcome the limitations of the FLAC3D model, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. The effect of stress rotation in the mining-induced stress field was considered by using a different geometry of rock fractures in the coal seam. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) were also considered by using Monte Carlo simulations. Consequently, the 3DEC models using the DFN technique resulted in predictions of floor heave that agreed with observations of the relative amounts of heave from each gate-road system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Apr 14, 2022

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Feida Wu, Yuhang Liu, Huimin Gao, Yuhan Song, Zhi Liu, Zijie Ren

In the process of quartz purification by calcination water quenching, the different expansion rates of gangue minerals and quartz were used to produce cracks or remove fluid inclusions, which is conducive to subsequent purification. However, the role and mechanism of calcination-water quenching are still lacking in research. In this paper, the position of calcinationwater quenching in gangue quartz purification process was adjusted and the removal effect of calcination-water quenching process at different nodes in the process was explored. The results show that the purification effects of grinding-calcinationwater quenching-classification-acid leaching process and grinding-classification-acid leaching-calcination-water quenching process were relatively good. The main reason is that calcined water quenching can make quartz produce cracks, which are more rough. At the same time, calcined water quenching is located after grinding, which has a larger specific surface area, pore volume and pore diameter, and has a strong adsorption capacity for acid solutions.

Nov 2, 2023

By Luis Pommier

In the United States, about one-quarter of the fuel oil and natural gas consumption is associated with power production in utility and industrial boilers and process heat needs in industrial furnaces. Coal has been an attractive candidate for replacement of these premium fuels because of its low cost, but there are penalties associated with the solid fuel form. In many cases pulverized coal is unacceptable as a premium fuel replacement because of the extensive cost of retrofitting an existing boiler designed to burn oil or gas. In the cases of synthetic fuels from coal, research and development still has a long way to go and the costs of research and development are very high. Another option which appears very attractive is the use of solid coal in a liquid fuel form, coal slurry fuels. Occidental Research Corporation (ORC) has been developing coal slurry fuels in conjunction with Island Creek Coal (ICC,) Occidental Petroleum's wholly-owned subsidiary. Both Coal-Oil Mixtures and Coal -Water Mixtures are under development. ICC is a large eastern coal producer, engaged in the production and marketing of bituminous coal, both utility steam and high quality/low volatile metallurgical coals. A sister division, Sheridan Enterprises is engaged in the development of western coals.

Jan 1, 1983

Joy Mining Machinery has developed a new generation of ultra-heavy shields for Anglo Coal Australia?s Moranbah North Mine in the Bowen Basin region of Queensland. These are the largest two-leg longwall shields yet produced by Joy. The longwall at Moranbah North posed a number of challenges, among them a thick, inclined, sometimes undulating seam with increasing depths. The result of this was the need for larger, heavier, more powerful roof supports. Knowing that future longwalls would be going deeper, mine management determined that shield yield ratings of at least 1,750 t (1,930 st) was what would be required.

Jan 1, 2011

By Mustafa Kumral, Samer Hmoud

Effective management of ore loss and dilution is essential for successful grade control and short-term mine planning due to their significant impact on the economic, environmental and technical aspects of openpit mining operations. Factors influencing ore loss and dilution fall into two categories: (1) controllable factors, like mine equipment selectivity and blast design, and (2) uncontrollable factors, such as spatial heterogeneity of ore and waste blocks on a bench. This paper focuses on the second category by applying spatial entropy concept to capture heterogeneity at the scale of selective mining units. In this paper, global spatial entropy is used to assess the impact of spatial heterogeneity between ore and waste blocks on the magnitude of ore loss and dilution, while the local spatial entropy can guide the allocation of blast movement monitoring balls preblast. High values of the global spatial entropy indicate increasing potential of ore loss and dilution, which reduce profit. Furthermore, through a number of case studies, the study investigates the relationship between spatial entropy, cutoff grades, blast movement, dig-limits optimization model running time, and profit. The results show that changes in cutoff grade and blast movement can significantly affect spatial entropy post-blasting and increase ore loss, dilution and profit reduction, revealing the need for controlled blasting at specific bench sections. Additionally, the results demonstrate an exponential increase in profit reduction due to ore loss and dilution with a rising global spatial entropy

Jun 1, 2024

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By R. Venkataramani

Even though the mining industry in 1966 produced more ore than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. Nearly 90% of all metals and-mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which has, consequently, resulted in some spectacular developments. With increasing size of projects, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today's business and social environments is undergoing an evolutionary process. Traditional concepts in mine development and operations are being sidestepped in favor of new ideas and principles. As the overburden thickness increases, materials handling presents a major problem to mining companies, especially those concerned with the mass production of ore and waste from low-grade deposits. The profit margin here is likely to be significantly less as to take chances with capital investment. 1 Constant efforts are needed to improve upon productivity if the ore is to be economically mined.

Jan 1, 1970

By E. L. Bohnet

The purpose of this paper is to translate a mining company's "Corporate Objectives" into usable and practical guidelines for long term mine design and production scheduling. These guidelines are required to ensure that both operating and development properties are designed and economically ranked on the same basis, and with the "current" Corporate Objectives in mind. Secondly, if both management and mining engineers have a better understanding of the cause and effect of corporate policies, then penalties and risks associated with various Corporate Objectives can be put into better perspective for management. Corporate Objectives, relative to usable guidelines for either short and/or long term mine planning, could be defined as one or more of the following four objectives: 1) Maximize the recovery of the economic portion of the defined geologic resources, and hence, maximize total non-discounted project cash flows and profits (most common approach in mine design), 2) Maximize the Net Present Value (NPV) of the after-tax cash flows from each existing or proposed project, either on an individual basis or in concert with other projects, including downstream processing facilities (primary method used to judge relative investment merit of a proposed development or operating concept), 3) Limit short and long term capital expenditures to a defined ceiling, 4) Maximize product output for the existing facilities in the short term, or conversely, keep commodity production at a constant level for a series of years.

Jan 1, 1994

By P. R. Taylor

Three refractory gold concentrates have been tested to evaluate the effect of roasting with hydrated lime followed by cyanidation. The results indicate that it may be possible to roast in such a manner as to contain nearly all of the sulfur, arsenic and antimony in the roaster calcine. Cyanidation results indicate that the gold recoveries are greater than 80% for all three concentrates.

Jan 1, 1993

By Ted T. Biddle

The world energy crisis has created a greatly expanded exploration program for energy fuels. The demand for materials required for drilling operations such as barite, which is the primary component of drilling fluids, has increased proportionally. As in the case of many other minerals, existing high grade barite mines are no longer capable of producing the required tonnage. Consequently, exploration and development of lower grade ore bodies has been increased. The need to produce a high quality product at maximum recovery rates, along with the ever changing economics affecting both selling price and production costs has triggered accelerated research programs toward more sophisticated and efficient beneficiation methods. Taking into account the specific gravity differential between barite (4.5) and the normal gangue minerals such as silica and calcite (2.7), gravity concentration methods are the prime consideration with flotation as a scavenging process. Greater emphasis on particle size liberation, size reduction and concentration is also indicated. In order to accomplish these objectives, it has been necessary to revert back to the old adage, "Recover your minerals as soon as they are free."

Jan 1, 1980