Search Documents

Shallow ore deposits are mined by surface methods but a depth is reached in the case of most deposits after which underground methods are applied for the extraction of the remaining ore. The determination of this depth and its analysis is the subject of this paper. In order to determine transition depth from open-pit to underground mining on the basis of the allowable and economically feasible overall stripping ratios, an economic-mathematical equation is first introduced. Using the achieved equation and an analytical procedure on a particular two-dimensional hypothetical tabulate deposit, an effective formula is then established. The formula introduced here, together with the procedure adopted, could be used in all similar mining situations by the mining design engineer.

Jan 1, 2010

By E. J. Rorem

Rockfall and unstable rock slopes can be effectively controlled by utilizing steel wire rope net systems, either as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting, permitting kinetic energy dissipation, yet providing high strength and consequently low maintenance. A review of the design considerations involved with these systems, as well as a review of several mine and non-mine installations is presented with the hope that the information may contribute to the safety against the dangers of rockfall and other mine hazards in active and abandoned mines.

Jan 1, 1996

By Roy L. Klein

The production of synthetic fuels from coal has been pioneered by South Africa. South Africa made a decision in 1975, due to the threat of an oil embargo, to proceed with the construction of Sasol Two, then followed by Sasol Three. South Africa has large coal but little indigenous petroleum reserves. The indirect coal liquefaction process used by Sasol since 1955 is the only commercially demonstrated method available for producing transport fuels from coal. The new plants consume 27 million tons per year of coal from a single mine that now produces transport fuels in sufficient quantities for energy independence.

Jan 1, 1983

By R. L. Miller

The potential for recovery of enriched uranium from spent nuclear fuel which has been consolidated into a nuclear waste form was explored in the studies reported here. The waste form of interest is iron-enriched basalt (IEB)--a silicate-based, fused-cast ceramic. IEB samples were prepared containing fuel assembly materials that simulate the core debris of Three Mile Island Unit II;1,2 the nominal composition of the consolidated waste form is given in Table 1. Ore Types The IEB samples, or man-made uranium ores (MMUO), are in two different mineralogical forms. Each MU0 was made by melting the constituent materials and holding at about 1500°C for 1 h. The MMUOs were then heat treated to control crystallization and crystal growth and then cooled to room temperature.

Jan 1, 1983

By G. T. Adel

The application of automatic control to mineral processing operations has been gaining momentum during recent years. Many strategies are being developed for controlling crushing, grinding and flotation circuits, however, their implementation in industrial plants is being slowed down because of the costs and difficulties in evaluating these strategies in a systematic manner. An interactive computer simulation package, developed at the University of California, provides the capability of analyzing the process dynamics of mineral processing circuits. This paper presents an overview of the simulator and its application to the case studies of grinding and flotation.

Jan 1, 1983

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By George F. McKeregahan

Phosphate production of the Central Florida Phosphate District has been predominantly from the unique and lucrative Bone Valley Formation, with local and minor amounts coming from the underlying Hawthorn Formation. As the Bone Valley is depleted, replacement production will move progressively into areas of total Hawthorn Production. Significant changes in the characteristics and make-up of the deposit dictate required modifications in mining and beneficiation. Failure to tailor technology to fit the deposits of the future will result in vast "reserve" losses. In the Southern Extension of the Central District - two distinct "ore types" exist. These are presently referred to as the upper (high grade) zone and the lower (low grade) zone. The upper zone is somewhat similar to the Bone Valley Formation and will respond favorably to present beneficiacion practices. The lower zone is strikingly different and its response to conventional beneficiation is not acceptable. The major differences are in grain size distribution and mineralogical make-up of these grains. The Hawthorn differs from the Bone Valley by exhibiting lower grades, lower tonnage yield per acre foot, lower pebble percent of product, higher mining ratios, higher slimes (-150 mesh) content and deeper mining depths. Physical characteristic changes include more frequent occurrences of competent bands or lenses of "limerock" which are submarginal in value.

Jan 1, 1983

By E. A. Noble

In the Western Coal Region, successful reclamation of surface-mined areas includes the protection of groundwater sources. To accomplish this, a complete understanding of the geohydrology of the affected area is imperative. Successful mine design also calls for careful attention to geohydrology. Because the Western Coal Region is semi-arid land used mainly for farming and grazing, groundwater is a particularly sensitive topic. It is especially sensitive where the lignite scheduled for mining is itself the aquifer supplying the farms and ranches. Such is the case throughout much of the Western Coal Region, particularly where there are no near-surface sand and gravel aquifers that are commonly found in the glaciated portions of the Region. Just as mining can adversely affect groundwater supply, so can groundwater adversely affect mining. Mine flooding and highwall instability are examples of this. But, mine operators must realize that procedures they use to remedy geohydrologically-related mining problems can have a dramatic effect upon ground- water conditions in areas adjacent to the mine. A logical precaution is to require the acquisition of complete baseline data prior to making the first cut. We recommend that the mining plan not only incorporate the reclamation plan, but that they be developed as one plan.

Jan 1, 1976

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985

By Frank C. Di Luzio

REMARKS BY FRANK C. DI LUZIO, ASSISTANT SECRETARY OF THE INTERIOR FOR WATER POLLUTION CONTROL, BEFORE THE ANNUAL MEETING OF THE AMERICAN INSTITUTE OF MINING ENGINEERS, NEW YORK CITY, FEBRUARY 25-29, 1968 POLLUTION PROBLEMS AFTER MUNICIPAL-INDUSTRIAL WASTE CONTROL I am happy to have this opportunity to discuss pollution problems related to the mining industry and the role of mining engineers in protecting our environment. Technological Power and Pollution of the Environment The increasing power of technology to destroy and disrupt the natural environment and the ecological systems upon which life depends has reduced man's margin for error in the use of this power. We must act, therefore, to deter and prevent the occurrence of future ecological disasters such as that caused on the British and French coasts by the sunken oil tanker, the TORREY CANYON, the Clinch River fish kill which occurred when a dam broke and released coal ash from a power plant operation, or that which threatened on the Clark Fork River in Montana when a strike at the Anaconda Copper Company threatened to shut down pollution control activities, thereby endangering fish and plant life on the Clark Fork River with copper waste. In the past, pollution of the environment has tended to be slow. But now, the increased power of technology to damage nature, the loss of in¬sulating space and the compression of time--all reduce our margin for error and the cushion which space and time once provided for our mistakes.

Jan 1, 1968

By Stephen H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, New Mexico area. The first four shafts sunk at international Minerals and Chemical Corporation's property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 Shaft there has been extensive-erosion and salt dissolution in the Rustler Formation which has led to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows it was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be codified to reflect any new or additional information which is obtained during the progress of the grouting.

Jan 1, 1984

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By Raj K. Rajamani

In ball milling the rates of breakage vary primarily with the size distribution of powder in the mill. In wet grinding viscosity of the slurry varies continually as size distribution changes and hence the breakage rates change. In this study a simpler estimation scheme is used to determine breakage rates in batch grinding. Using an approximate solution to the batch grinding equation, acceleration and deceleration of breakage rates of all individual size classes is determined when the grinding environment is varied. Experimental results with limestone and copper ore show time-dependent breakage rates under both dry and wet grinding conditions. In general the breakage rates increase for coarse sizes and decrease for fine sizes with increase in the fines present in the mill. Such variations have strong implications in closed-circuit grinding.

Jan 1, 1991

By M. V. K. Reddy

A differential flotation process for recovery of molybdenite from chalcopyrite concentrates produced at Rakha Copper Concentrator, Bihar, India has been developed. The flowsheet is simple, and relatively inexpensive and yields a concentrate assaying not less than 45% Mo at a recovery of minimum 65%, starting from chalcopyrite concentrate assaying 0.4% Mo. The consumption of the main depressant used, sodium sulphide is not more than 25 kg/t of copper concentrate processed without steaming; and with steaming the consumption was brought dorm to less than 12 kg/t of concentrate. Further reduction is possible by optimization of steaming parameters. Based on laboratory experimental results, further tests were conducted on concentrator site and process design parameters were established for design of commercial plant.

Jan 1, 1982

By O. V. Bush

Most governments recognize that energy efficiency represents a partial solution to reducing global capital shortages and environmental crises that threaten to seriously impede economic growth. Much of the United States and many foreign countries are embracing the concept of Integrated Resource Planning (IRP) which incorporates Supply Side Management (SSM) and Demand Side Management (DSM). Since SSM comes at twice to three times the cost of DSM, it makes economic sense to employ the energy conservation techniques of DSM. This paper will explain these concepts and some of the incentives being put forward by governments and utilities to promote DSM.

Jan 1, 1995

By K. Papke

Nine western states contain significant barite deposits, but most deposits are in Nevada, which has been the principal western producer for more than three decades. Nevada produces about 85% of the total United States production, but about one-half of the barite consumed in the country is imported. Approximately 95% of the barite is used in drilling muds. Sharply decreased oil and gas drilling, starting in early 1982, severely depressed the domestic barite industry. Other problems for western barite include long distances to the areas of major drilling, high railroad-freight rates, and increased barite imports. Bedded deposits, formed by submarine exhalative processes, account for almost all western production, and reserves are large.

Jan 1, 1983

By O. E. Wheeler

The use of the walking dragline as a stripping tool has increased dramatically in the past two decades. The reasons for its increased popularity and some historical background on its introduction into the mines are given in a recent paper by Learmont. (l)* The history need not be recounted here except to show the trend to longer booms which has accompanied the growth in machine size. Figure 1 shows the change in maximum operating radius on Bucyrus-Erie machines which has occurred over the years and Figure 2 shows the corresponding change in maximum boom lengths. Reference 1 also presents some of the reasons for expecting this trend to longer booms to continue. There are many design parameters affected by the increase in boom lengths; swing power, hoist and drag rope lengths, and drum capacity, to list just a few. The purpose of this paper is to discuss only the structural implications of using longer booms. As in the design of any structure, the various facets of boom design are interrelated and a process of optimization between them must be worked out either by evolution or by conscious iterative effort. The decisions we have reached about such things as material selection, structural arrangement, and applicable criteria, have not come into being overnight but represent instead many years of design experience and a fair amount of recent concentrated analytical effort. In the following pages an attempt will be made to first, state those decisions, second, explain how we arrived at that particular result; and third, describe what we expect future developments to be which might influence us to change those decisions.

Jan 1, 1976

By Frederick J. Hoppe

The productivity or usefulness of a Front End Loader rises rapidly with its size. Loading is more aggressive. Mother Nature is defeated more easily. Larger tires get a better grip on the ground. Hauling equipment can be loaded more quickly. The productivity or usefulness of a Front End Loader is proportional to its working speed, both automotive and hydraulic. The price of speed is horsepower, which rises rapidly with speed. Horsepower saved shows up as increased productivity. This paper covers the development of the D600, KW-Dart's articulated loader, which combines massive size with new concepts to increase its working speed. Featured is a discussion of the horsepower saving, "Balanced Boom."

Jan 1, 1969

By Y. Wang, G. Xu, N. A. Amoah, A. Kumar

Mining-induced coal dust causes various respiratory diseases to mine workers, such as coal workers’ pneumoconiosis (CWP). Current available underground monitors are expensive, heavy and only measure mass concentration. These disadvantages limit them for regulatory sample monitoring purposes only while personal exposure levels for most miners remain unknown, risking miners to potential overexposures. Low-cost light scattering PM sensors offer a potential solution to this problem with capability of high spatio-temporal resolution PM characterization. However, these sensors require careful calibration before they can be applied in mining environments. There is basically no comprehensive study in the literature using a standard protocol assessing these sensors for coal dust monitoring. With the aim of calibrating the PMS5003 sensors for coal dust monitoring, we design the calibration method and system to calibrate these low-cost PM sensors coal dust monitoring. Working principles of present coal dust monitor and low-cost sensors are presented in detail. The linear regression calibration model which is used for the sensor calibration is further described. Sensor calibration and evaluation protocols are comprehensively compared and discussed. This investigation reveals the feasibility of low-cost sensors for real-time personal coal dust monitoring in underground coal mines.

Mar 2, 2022

By S. Jennings

The Red Dog massive sulfide deposit is located in the western Brooks Range of Alaska 100 miles north of the village of Kotzebue. It contains the largest zinc reserve in the world. Reserves were doubled in 1995 with the discovery of the Aqqaluk deposit and significantly increased in 1996, with the discovery of a deep zone of mineralization to the north. At present the global reserve and resource is 143 million tonnes of 16.1 % zinc and 4.3% lead. Red Dog is a silica + sulfide synsedimentary replacement deposit hosted in barite and black shale of the Mississippian Kuna Formation. Red Dog was thrust northward during the late Mesozoic Brookian orogeny. Understanding the setting of the deposit at the time of formation and its subsequent deformation history is critical to current exploration efforts and to future discoveries in the district.

Jan 1, 1998