Search Documents

By Heinz Hoberg, Fred Ulrich Schneider, Rudolf Diegel

The risk of contamination of dumped tailings and ground water by coal flotation reagents has been investigated by using the 14C-radiotracer method for adsorption and desorption measurements. The results indicate, that a high amount of the reagent components adsorbed on the tailings if there was no coal in the pulp. In coal flotation however a competitive adsorption behaviour could be observed, with the effect that only a low quantity of reagents adsorbed on the tailings. Mobilization tests showed, that only small quantities of reagents could be desorbed by rinsing water. Therefore the contamination of ground water should be low.

Jan 1, 1995

By L. R. Freitas, A. K. Resende, J. A. Oliveria, K. L. Gonçalves, L. F. D’Assumpção, L. R. Lage, J. D. Neto, F. Viveiros

Pará Pigmentos S.A. (PPSA) is an association between the Brazilian companies CVRD and CADAM, Mitsubishi Corporation of Japan, and the IFC (World Bank) created in 1992 in order to recover kaolin from Rio Capim deposit, northern Brazil. Commercial production at PPSA started in August 1996 using a process comprising mining and beneficiation at the mine site, pumping through a pipeline and drying/loading at the port site on the Amazon river estuary. Presently, all PPSA production is concentrated on 82% <2um, high-brightness coating clay shipped in bulk. In this paper, a detailed description of the development of PPSA beneficiation process is presented. The results of laboratory and pilot plant studies under- taken to develop alternative grades of clay, such as delaminated and calcined kaolins, are also discussed.

Jan 1, 1998

By C. L. Karr, D. E. Goldberg

This paper considers optimization of the design and operation of an air-injected hydrocyclone (AIHC) via a genetic algorithm (CAI. The AIHC is a mineral separating device, developed by the U.S. Bureau of Mines, that combines the selectivity of flotation with the capacity and simplicity of hydrocyclones. GA&apos;s are search procedures based on the mechanics of natural genetics. Computer results demonstrate the ability of a GA to rapidly locate design and operating parameters that improve AIHC performance. A computer model of the GA-designed AIHC predicts improved recovery over that currently being obtained with an AIHC in operation at the U.S. Bureau of Mines Tuscaloosa Research Center.

Jan 1, 1990

By Jaroslaw Drelich

This report briefly reviews the measurements and interpretation of adhesion forces measured between microscopic probes and substrates having micro- and nanoscaled roughness characteristics that were recently conducted at Michigan Tech using atomic force microscopy. The laboratory study concentrated on both rigid and deformable materials, with the probes larger than the size of roughness features of interacting surfaces. For such systems, a detailed surface characterization in terms of roughness parameters, asperity size and shape, and spacing between asperities, as well as analysis of deformation of materials is required. Analysis of the experimental data can be done with theoretical models, which are suitable for rough surfaces and therefore allows to normalize the measured forces. Alternatively, loading of the probe during adhesion force measurements can be managed properly to control deformations of the nano-scaled surface irregularities. Controlling the deformation reduces and even eliminates the effects of nano-roughness on the probesubstrate contact area, promoting conditions described by the contact mechanics models for the sphere-smooth substrate system.

Jan 1, 2005

By Pradip

It is possible to beneficiate low-grade phosphate ore slimes containing predominantly siliceous gangue by a combined selective flocculation-flotation scheme using commercially available reagents. The presence of clays, in particular, montmorillonite and attapulgite, has a disastrous effect on the efficiency of separation. Suitable remedies to overcome this problem are not yet available. Intensive R&D efforts are required in the areas of the design and synthesis of specific reagents, the effect of particle size, and the design of appropriate process equipment to carry out flocculation and flotation of slimes.

Jan 1, 1989

By Carl P. Maronde, William P. Barnett, Patricia A. Rawls

The commercial deployment of advanced fine-coal cleaning technologies depends on cost-effective approaches for efficient separation and ancillary operations in handling, dewatering, drying, and transporting coal fines. As a result of two solicitations under the High-Efficiency Preparation component of the Department of Energy Coal Preparation Program, several projects were initiated for testing and evaluation of emerging technologies and equipment that address operational difficulties associated with coal fines. This paper will update the status of those projects and discuss how the technologies they represent can ameliorate some problems associated with coal fines in today&apos;s preparation plants.

Jan 1, 1995

By D. W. Horsfall

The washability of South African coals is described and the problems encountered in washing at low densities, to make premium products, are enumerated. The measures taken to overcome those problems, when low density separations became a commercial necessity, are described in detail. The descriptions of processes are with specific reference to the three sizes commonly treated separately in coal preparation namely coarse coal, small coal, and fine coal. Some information is given on the performance characteristics of the plants erected to meet market requirements.

Jan 1, 1995

By Thomas E. Shufflebarger

Glass sand is a virtually pure, fine- to medium-grained, quartz sand. It is produced in 25 states from a variety of chemically different source rocks. Deriving their raw material largely from either friable sandstones or loosely consolidated sands, 59 operations produced 14.9 million tons of melting sand in 1976. About one-third of this tonnage was obtained from the Oriskany and St. Peter Sandstones. Glass-sand prospects are discussed in this paper with regard to chemistry, environment, transportation, and costs. Demand for a quality product will range from 36 million to 46 million short tons in 1995.

Jan 1, 1978

By R. P. Plasket, G. M. Dunn

The cobalt plant was successfully commissioned in mid-1983. It is located within the company&apos;s nickel - copper re finery situated in Springs, South Africa. Plant design, which began in 1981, made provision for the corrosive process environment, stringent environmental standards, and the latest noise abatement requirements. In addition, the process flowsheet for the primary recovery of the cobalt byproduct and the purging of six impurity metals (nickel, iron, copper, manganese, lead, and arsenic) was designed with simplicity as a primary objective. High purity cobalt powder has been produced since commissioning.

Jan 1, 1987

By J. P. Savely, D. E. Nicholas, R. D. Call

Slope stability is a probabilistic phenomenon and as such should be analyzed with probabilistic methods. Fracture orientations alone, insufficiently model the rock mass. Other parameters describing the fracture set characteristics are required with distributions that can be sampled to fit mathematical stability models. Important considerations are length, spacing, dip, waviness angle, and overlap. These parameters are of major concern in design and are difficult to measure. Reasonable estimates of the characteristics can be used to provide distributions.

Jan 1, 1977

By R. D. Kelsey

The theory, definition and practical application of cutoff grades have evolved over a long period. This evolution is reflected in the continuing flow of papers on this and other related matters though the rate has varied as new ideas and theories have become understood and applied in practice. Papers by Lane(l) in 1964 and Taylor(-2)- in 1972 provided landmarks in the understanding and general communication of cutoff grade theory and its application. The reasons for the continuing interest in cutoff grades are obvious. Too high a cutoff can reduce the mineral recovered and possibly the life of a deposit. Too low a cutoff would reduce the average grade (and hence profit) below acceptable levels. This paper provides a brief overview of existing cutoff grade theory and some particular aspects of its application.

Jan 1, 1979

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By E. F. Divers

Adequate ventilation of coal mine working faces is the most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. US Bureau of Mines research has shown that to control respirable dust, you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane, the most effective approach has been to use a blowing brattice, or tubing, and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present. Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan- powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray- fan controls methane on exhaust-ventilated sections.

Jan 1, 1987

By Nikolay M. Sirakov, Michael L. Feves, Rumen P. Mironov, Daniel R. Hack

Subsurface investigation of sand and gravel deposits has generally been limited to test pits and borings. These techniques are problematic in terms of the accuracy, usability, and cost of the final data. Innovations in the application of geophysics have been gaining acceptance in the aggregate industry, especially to determine depth to bedrock and the extent of uneconomic inclusions. This paper presents a system to optimize the processing and evaluation of electrical resistivity data. The system uses 3D separation, geometrical reconstruction, and visualization of subsurface objects.

Jan 1, 2002

By Donald P. Spitzer, Peter V. Avotins

The flow properties of thickener underflow slurries can be characterized by their rheological parameters. Most of these slurries exhibit Bingham plastic behavior, characterized by a yield stress, to, and a Bingham viscosity, nB. Red mud is generated as a leach residue in the Bayer process. The use of new Bayer process flocculants which contain hydroxamate functional groups leads to muds which are qua1itatively considerably more fluid than muds generated with conventional polyacrylates or acrylatefamide copolymers. A variety of rheological tests confirm lower yield stresses and less extended floc structures with the new flocculants, at the same solids levels. Conversely, under given viscosity restraints, the new polymers make it possible to operate at higher solids levels, which offers major benefits in processing red muds.

Jan 1, 1992

By O. Fernandez, M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material buildup inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design, and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 t/d (1100 stpd) and significant operating costs savings.

Jan 1, 1987

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By Raul Z. L. Cançado, Virginia S. T. Ciminelli, Roberto Galery, Armando C. de Araujo

Brazil is presently among the seven largest gold producing countries in the world. This paper discusses the evolution of gold mining through the history of Brazil. It also gives a general account of the present practices for mining, processing and extraction of gold. Flowsheets of some selected plants are presented. The environmental aspects involved with gold production are also considered.

Jan 1, 1987

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, a group called Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903± hm2 (22,000± acres) on Black Mountain, which contains the state&apos;s highest point, as unsuitable for mining. A fast track legislative process was triggered that could have "taken" 91 Mt (100 million st) of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed

Jan 1, 2002

By James E. McTurk, Sheldon B. Bland, Roger E. Melley

During the first fifteen years of operation at the Syncrude facility in northern Alberta, numerous improvements have been made in the field of ore conveying. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about with the use of detailed field evaluation. This paper outlines some of the programs which have been run to optimise belt and system construction, and conveyor performance and utilization.

Jan 1, 1993