Search Documents

By Thomas E. Shufflebarger

Glass is one of man's most versatile creations. ---The earliest glaze known---is about 12,000 B.C. ---The oldest pure glass is a moulded amulet of about 7,000 B.C.---. Indicative of a knowledge of properly-proportioned, quality raw-material, means were found for producing the first relatively clear, transparent glass at about the beginning of the Christian era. The fundamentals of almost all the modern, technical processes of manufacture were established during the 3rd Century. (1) Glassmaking, practiced in Colonial America, was moved toward the Ohio Valley in response to increasing demands for fuel. This move, beginning in the 1860's resulted in the use of the glass sands contained in the Oriskany (and St. Peter) sandstone. (2) Glass sand,(3) virtually pure, fine-to-medium-grained quartz sand(4) is the principal raw material used in the manufacture of glass; it constitutes proportions which range to a maximum of about 72% and seldom is glass made without it. However, acceptable glass sands are, invariably, those which most nearly fit the glass-producer's economic needs and any method used to evaluate a raw material's potential must finally prove equatable with such needs. As used in the United States, source-rocks of glass sand include sandstone, unconsolidated silica sands, quartzites and vein-quartz. Admixtures of silica sand and other (principally clay and feldspar), readily separable components have been proven viable. However, the silica sand, refined by nature to a high degree of purity, is the desirable product of exploration. If the term, standard, is justified by long-continued use, the Oriskany - and St. Peter sandstones are, together, the nonesuch of the glass sand industry they provide the principal tonnage of melting sand. According to Grimsley,(5) Ottawa, Illinois, glass-sand is considered the standard glass-sand of the West and the analyses of Berkeley Springs sand (Oriskany) compare most favorably with this sand.

Jan 1, 1974

By Ernst P. Hall

The Irwin Basin. (Fig. 1)* is a synclinal or shoe-horn *Figure numbers throughout refer to color slides not included with the preprint shaped basin in the Pittsburgh Coal Seam, It is approximately 10 miles wide and 22 miles long at its maximum points. The surface of the land above the basin is hilly, rolling farmland,, typical of this area of Pennsylvania, and it is criss-crossed with streams and highways and liberally dotted with farm houses and communities. In-general the coal is pitched from north to south with a total drop of 610 feet'. The coal seam cross-section from east to west is bowl-shaped and rises as much as 375 feet from the low point of the bowl to-the-outcrop. Cross-sections showing coal elevations are shown on Figs, 4 and 50 Ground cover above the coal will vary from 0 to 550 feet, averaging about 350 feet throughout the area. This area is richly endowed with a history of coal mining. The first car of coal shipped cast of the Allegheny Mountains was mined in the Westmoreland Coal Company's Shady Grove (later North Side) Colliery in Irwin, Pa., early in 1853, This mine was opened in 1852 by Coleman, Hillman & Company. The coal was hauled from the mine to the freight station by horse-drawn wagon and. loaded into a then "standard" box car of 18,000-pound capacity. Coal mining in this region flourished and grew as steel production in nearby Pittsburgh demanded more and more of the high quality, metallurgical-grade coal of the region.

Jan 1, 1959

By M. Beale

Fuzzy logic and neural networks are new technologies being applied in many areas of engineering and business. While it is not always clear which kinds of problems are best suited to these technologies, and which problems are best approached with more standard methodologies, both fuzzy logic and neural networks appear to show great promise in the field of control systems. This paper demonstrates two advantages that these technologies offer: Easy controller design in the absence of a mathematical model of the plant to be controlled, and adaptive control capable of quickly responding to changes in the plant.

Jan 1, 1994

By Alexander Sutulov

It is calculated that since the beginning of last century, which practically coincides with the beginning of the Industrial Revolution, our civilization has consumed around 239.5 million tons of copper (see: Table 1). According to the most pessimistic projections of today, with only a 2.5% annual growth rate in demand, we are bound until the end of this century to consume another 200 million tons of copper in remaining 17 years. A recent study made by US Bureau of Mines (1) indicates that the proven ore reserves of 150 major operating mines and about 120 deposits sufficiently explored for development and feasibility studies accumulate a total mass of 49.3 billion tons of ore, assaying an average of 0.82% Cu and containing around 324 million tons of recoverable copper. Consequently, there is a high grade of probability that the bulk of our future ore supplies, for our demand of, say, next 25 years will cane precisely from these mines. The interesting point in USBM study is that it indicates the recoverable byproduct content of these ores and which is: 118.2 million troy ounces of gold 2277.4 million troy ounces of silver 7.1 million tons of lead 24.7 million tons of zinc 1.3 million tons of nickel 3.1 million tons of molybdenum 765 thousand tons of cobalt, and 720 thousand troy ounces of platinum. This information gives us a relatively reliable profile of our future ores for next 25 years, and thus makes possible evaluation of byproduct credits in our future copper mining and producing activities.

Jan 1, 1983

By William E. Robinson

Our earthly treasures are being quickly depleted. We have experienced what can happen in an energy crisis. You have read and heard all kinds of stories as to what caused this crisis. On the surface it would seem that all of a sudden a situation becomes a crisis whether it be fuel, potatoes, beef or whatever. Well, of course, they don't just happen. There is always a little fore-warning here, an indicator there. Someone recognizes a sign of potential trouble but is ridiculed when he forecasts it. We are running out of sand: Producers of aggregates who can say today ... "That couldn't happen to me", can well be awakened tomorrow to the cold fact of reality. It could come from any number of directions. Depletion is mostly foreseeable but zoning isn't. Legislation can also be sudden death to availibility. With the ever growing population moving into the rural countryside, available deposits are being sold either to developers or being zoned for restricted use. The fact that a gravel pit or quarry is located on a particular plot has not fazed some of the local planning boards when they decided to place the adjoining property in a residential Zone A. Proponents of zoning preach that such use is necessary to insure that the land will be put to its best use. Planning boards establish the best places for schools, homes, shopping areas, factories, etc., so that the individuals or groups are in harmony with each other. This is usually done to date without thought or consideration to the geological importance or potential of the area. Today over half of the United States is living under some form of land use restriction. Little consideration has been given to what lies under the ground to be zoned. Fortunately, the states are slowly getting around to geological surveying. I feel that it is about time that state and federal authorities institute governmental restrictions to prohibit or control local zoning ordinances which would deplete or deny an area of its natural resources. While I could continue for the balance of my time just on this facet of our industry's problems, my point is: How sure are you of your next load of sand? I could be well laughed at by some of you for saying that there is an alarmingly rapid disappearance of "nearby" sand and gravel reserves in many areas of the country. A questionable statement, except to those producers where depletion has already taken place.

Jan 1, 1974

By Kadri Dagdelen, Steven Hoerger

For gold mines, orebody uncertainty is one of the leading causes of differences between planned and actual production. Geostatistical conditional simulations create multiple equally probable orebody block model realizations which are conditional to the current drilling information and demonstrate the sampled grade distributions and spatial statistics. These simulated block models are key inputs for a stochastic evaluation to show the likely range of grades and cash flows to be delivered by a mine plan. The stochastic evaluation outputs can be used to compare different mine plans in terms of expected values and risks to planned grades, production, costs, Net Present Value (NPV) and other plan metrics. For the McLaughlin gold mine, risk profiles are demonstrated to show how different mine, cut-off and stockpile strategies can reduce risk and improve expected value. The strategies considered were effective in improving expected NPV and reducing or eliminating tonnage uncertainty, but the strategies had little impact on reducing the uncertainty of NPV’s or mill grades. The stochastic evaluation process is also used to compare the risk impact of orebody uncertainty against the risk of not achieving planned mining tonnages or vertical advance rates. Risks for plans created with and without stochastic mine plan optimization are also compared.

Feb 1, 2025

By T. McNulty

The author was privileged to find employment as a uranium mill chemist for The Anaconda Company while working his way through school in the mid-1950s. He then served Anaconda in various technical and management positions until 1980. This paper describes the prevalent technologies employed by uranium producers, briefly describes various mines and mills in the U. S., and memorializes a few of the thousands of men and women who contributed to the U. S. Uranium Boom. Following isolation of uranium as an element by M. H. Klaproth in 1789, uses of uranium were confined primarily to pigments, glass coloring agents, and ceramic glazes. In 1896, Antoine Becquerel found that uranium is radioactive, releasing particles and energy as it decays. In 1898, Pierre and Marie Curie isolated radium from uranium and learned that it can be an effective treatment for some types of cancer. In 1939, it was discovered that the isotope U235 is fissionable1 . Up to this point, nearly all uranium production was from pitchblende concentrates made in Bohemia, Canada, and the Belgian Congo. In 1938, only about 5 percent (23.85 short tons) of global output was produced from ores of the carnotite mineral that were being mined in the U.S. By the early-1950s, physicists in many countries had begun to recognize the potential for nuclear chain reactions. Ernest Rutherford (UK), Frederick Soddy (UK), and Leo Szilard (US) explained transmutation of elements and formulated the principle of “atom splitting”. In 1934, Marie Curie’s daughter, Irène, and her husband, Frédéric Joliot, identified uranium as the most viable source for this new form of energy. The basic fission process was unraveled by German scientists in December 1938. After Hitler’s army seized the uranium deposits in Czechoslovakia, many feared that Germany would build the first nuclear weapon.

Mar 2, 2022

Optimal gold recoveries largely depend on efficient liberation of the gold or gold-bearing minerals as well as on maximum access for the lixiviant. Thus, crushing and grinding may become the most costly part of gold ore processing. It may, in fact, represent 50% to 70% of a plant's operating costs (Michaelis, 1989). The increasing significance of refractory gold will require even more cost-efficient comminution of ultrafine sulfides and/or native gold. Transitional ore zones with semi refractory gold may respond to direct leaching if better particle fracturing is being achieved (Baum, 1991, 1993a). Many oxide ores have been left in the ground because they were unsuitable for heap leaching since conventional comminution could not facilitate economic gold extraction. Also, the costs of conventional bal1 mill operations did not permit the recovery of gold from many ultrafine, low-grade refractory ores. As shown by Marsden et al. (1993), the trend to treat ores with progressively lower grades will involve power-and leach-efficient grinding applications. Our current laboratory work shows that high-pressure grinding roll (HPGR) Polycom grinding may enable many mining companies to add large amounts of these "non-leachable" ores to their current heap or mill leach feeds. This finding may dramatically change the economics of many oxide gold ore operations and may add significant reserves to ores amenable to direct cyanidation.

Jan 1, 1994

By Juan Ares, Enrique Fernández, Alejandro Sanz, Francisco González

"INTRODUCTION Crossrail is a subsidiary company of Transport for London created for the construction of a new transverse train line 118 km long between Maidenhead and Heathrow in the West, and Shenfield and Abbey Wood in the East, including 21 km underground below London. Crossrail C305 Eastern Running Tunnels project is the biggest contract within Crossrail Project and involved boring 11.8 km of twin tunnels through London’s city center. Crossrail C305 Project interfaced with different contracts along its alignment and therefore logistics and solutions had to be developed to minimize disruptions or interferences with other contractors and the neighborhood. The paper describes this innovative approach. C305 CONTRACT APPROACH C305 contract was split into three drives, to be excavated by four EPB TBMs 7.1m diameter, as shown in Figure 1. •,Drive Y: 8.2km long between Limmo Peninsula and Farringdon Station in the city center •,Drive Z: 2.7km long between Pudding Mill Lane and Stepney Green Junction •,Drive G: 0.9km long between Limmo Peninsula and Victoria Dock Portal in the East. Crossrail C305 Project scope of works included the excavation of TBM tunnels and shafts at Limmo Peninsula and Stepney Green (including 17m span turnout caverns), along with the requirement to traverse station and shaft structures of other Crossrail contracts. Limmo Peninsula Site was a strategic element as it was the only access point on the tunnel alignment with sufficient available area at the surface for tunnelling logistics and also connected to the Lea River, tributary of the River Thames which facilitated marine operations for segment supply and muck removal. These were the reasons for operating Drive Y & Drive G TBMs from that location. Drive Z TBMs were originally planned to be launched from Stepney Green to Pudding Mill Lane, supplying the TBMs during Drive Z excavation from Limmo Peninsula site through the excavated section of Drive Y between Limmo and Stepney Green. During the early stages of the project, a value engineering proposal with a new tunneling strategy was agreed wherein the Pudding Mill Lane contractor would provide space for TBM assembly and operation in their portal, allowing for reversing Drive Z excavation and launching the two TBMs from Pudding Mill Lane. This optimization reduced some of the shaft requirements at Stepney Green which were contingent upon critical enabling works and provided program certainty and cost savings for the full Crossrail Project. It allowed for the reuse of both the Drive Z TBMs for Drive G excavation from Limmo to Victoria Dock Portal thereby saving on the procurement of two TBMs, in addition to easier logistics for both Drives Y&Z, therefore de-risking the TBM excavation process and the C305 Project program completion."

Jan 1, 2016

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By N. T. Cowper

Slurry viscosity ultimately affects the majority of mineral extraction processes. However, to date its role has been disguised because mineral processing equipment has been conservatively designed to operate at minimal slurry viscosity. With most ores this still meant acceptable solids concentration was achieved. However, with the advent of treatment of weathered ores the resulting higher slurry viscosity (rheology) has meant solids concentration has had to be reduced, often to unacceptable levels. To permit operation at higher solids concentration chemical dispersants are employed. These dispersants are expensive and their addition should be controlled. Slurry Systems Pty Limited (SSPL) has developed an On-Line Viscometer to monitor and control slurry viscosity, whether by controlling water addition or by controlling dispersant addition. Using this instrument the slurry rheology can be controlled at the optimum level, maximizing solids throughput, and minimizing water, reagent, and dispersant addition. This paper discusses rheology of typical mineral slurries, the relationship between slurry rheology and percent solids in a slurry, and the need for rheological control in mineral processing. The effects of rheology on various process steps, and the use of dispersants are reviewed. The paper concludes with summarizing actual case histories and cost impact of Theological control.

Jan 1, 1992

By Yoginder P. Chugh

The term "fatigue" in mechanics, is used to refer to reduction in the strength of a material subjected to fluctuating or alternating stresses. Stresses that vary with time are called fluctuating stresses and if during fluctuation the stresses also change sign, they are called alternating stresses. In the field of rock mechanics, the term fatigue (static fatigue) has often been misused to refer to failure of geologic materials in time domain under constant load. To avoid confusion, we use the ten cyclic fatigue here to refer to failure of rock under alternating or fluctuating stresses. Fatigue in metals has been studied for over 100 years. Fatigue properties of geologic materials have, however, received little attention in the past. This is probably because until recently very little was known in regard to the behavior of geologic materials even under static loading. Secondly, suitable equipment for conducting cyclic fatigue experiments was not available until quite recently. A few cyclic fatigue studies have been undertaken on geologic materials to relate it to percussive or rotary drilling mechanisms (e. g. Grover et a11*; Burdine2). The results of these studies were inconclusive due to limited effort. Cyclic fatigue in concrete has been studied more extensively than geologic materials (e.g. Nordby3, Gray et al 4 and Bennett et a15) and mechanisms of fatigue in concrete are better understood than in geologic materials.

Jan 1, 1975

By K. Thomson

The Mule Canyon gold deposit, located 14 miles ESE of Battle Mountain, Nevada, was discovered in 1986 as the result of a GFMC grass-roots exploration program. Drilling to date has identified six discrete orebodies which contain a demonstrated gold reserve of 8.487 million tons at an average grade of 0.136 oz/ton, totaling 1,152,000 ounces. Mineralization is associated with argillic alteration and silicification, localized along NNW trending high-angle faults within Miocene basaltic andesites. Trace element geochemistry at Mule Canyon is typical of upper level hot spring precious metal systems, displaying elevated Ag, As, Sb, Hg, and Se.

Jan 1, 1993

By M. Misra

The coral contaminated with plutonium at Johnston Atoll UA) was subjected to gravity and flotation separation processes at the Soil Washing Laboratory (SWL) and also at the Johnston Atoll UA) site. Tests were conducted with the contaminated coral fractions referred to as the "HP-l" ( hot particles) and the "sludge". The gravity process tested was centrifugal gravity separation and the flotation processes were conventional Denver mechanical flotation and tall column flotation. Flotation tests were conducted using both fresh and sea water. Industrial fatty acid (anionic collector) was chosen as collector to make plutonium-enriched particles hydrophobic. The use of flurosilicic acid and sodium silicate made the clean coral hydrophilic. The results show that each of the processed when tested with appropriate size fraction and operating conditions resulted in passing the success criteria. It was possible to obtain more than 80% weight of the original coral as "clean sand" having activity below the JA site "soil screening level" of 13.5 pCi/gm. The field tests spiked with plutonium particles showed remarkable success. The effect of depressants, flotation medium and the coral pretreatmentis described. Finally, a flowsheet developed by the University of Nevada, Reno to treat 8000 tons of HP-l pile presently stored at JA is presented.

Jan 1, 1996

By Karin Bäppler

"When considering large-scale infrastructure projects worldwide special attention has to be paid to the large diameter tunnel construction projects that were successfully completed in the Southern Hemisphere. The projects that are highlighted in this paper are large-scale infrastructure projects in the sector of transport. In focus are four road tunnel projects that were constructed in Australia and New Zealand using mechanized tunnelling technology. The tunnel boring machines (TBMs) that were reliably applied to these four major projects all exceed the bore diameter of 12 meters. These TBMs are therefore in the range of large to very large diameter TBMs. The technology used demonstrates state of the art technology with tailored tunnelling technology adapted to the specific project demands. Two Double Shielded Hard Rock TBMs (Ø 12.35 meters) were used for the construction of the Clem Jones Tunnel in Brisbane crossing beneath the Brisbane River and these two machines have been reused for the excavation of a 4.3km long two-lane highway tunnel for Legacy Way in Brisbane creating a new traffic artery towards the city centre. Two EPB Shields (Ø 12.48 meters) excavated and lined the twin-tube road tunnel for the Brisbane Airport Link. Excavation diameters in excess of 14 meters, such as the Earth Pressure Balance Shield (Ø 14.41 meters) involved in the Waterview Connection Project in New Zealand, are understood in the tunnelling industry as very large diameters. The machine is customized to the requirements and subsurface conditions of Auckland. The paper spotlights the large to very large diameter TBMs that were used and focuses on the comprehensive solutions developed by the machine manufacturer to provide a system with benefits for the contractor especially for the Waterview Project. INTRODUCTION Extensive large-scale road infrastructure projects like the ones implemented in Brisbane (Australia) and currently under construction in Auckland (New Zealand) show the tendency of today’s infrastructure construction projects. Functional infrastructures need to be put in place to cope with the demand of mobility and flexibility of people living in cities and metropolises. Impact during construction work to people or environment has to be kept as low as possible to ensure the quality of life is not disrupted."

Jan 1, 2016

By Leonard Sargeant

The Pocahontas Coal Field consists of eight mineable seams of low-volatile coal in southern West Virginia and Virginia. The deeper seams, especially the Pocahontas No. 3 and No.4 Seams, under heavy cover and below drainage are notoriously gassy. Methane in the Pocahontas Field is generally thought of as being confined in the coal itself, rather than in mud slips or clay veins. Furthermore, it is characteristic of Pocahontas coal to retain its gas until the coal is broken and removed from the solid. Because of this inability for gas to escape from unmined coal, entries developed around large blocks are seldom of significant value in bleeding off methane before pillar extraction begins. This is evidenced by the fact that it is not uncommon to find gas liberated during the mining of chain pillars and barriers which have been developed for several years. The Pocahontas Fuel Company develops almost all solid coal by conventional methods with shuttle car haulage. To provide the maximum productive capacity without compromising ventilation and safety requirements, the Company has adopted standards for ventilating 5, 6 and 7-entry sections.

Jan 1, 1960

By Henry H. Roos

The productivity of the underground driller has increased 500-600% during the past 20 years. This increase is not due so much to improved percussion drills as it is to improved drill support equipment and modernization of mining methods, Efforts to mechanize drilling in mining operations were made as early as the late 1800's; and, patents on rock drill manipulating machinery date back to 1906. However, the great rush to mechanization began in the 1950's when the development of trackless mining methods gave mining engineers and equipment designers their first opportunity to create improved operating conditions for the equipment and to match the equipment with these conditions. Accordingly, this paper will summarize the developments of the past 20 years and will attempt a forecast of developments that can be expected during the next few years.

Jan 1, 1970

By George Dials

Good morning gentlemen. My name is George Dials, and I am [vice] president of the Mining and Reclamation Council of America (MARC). The Council is composed of various companies, individuals, and affiliated state and regional trade organizations representing nearly 3,000 companies directly and indirectly involved with surface coal mining in the United States. I am very glad to be here today to address the Society of Mining Engineers of AIMS. While I do not pretend to be an expert in either geological or geotechnical engineering, I am infinitely familiar with the provisions of the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87) and the Federal regulations that have been promulgated pursuant to that Act. The Office of Surface Mining Reclamation and Enforcement (OSM) was created by P.L. 95-87 within the responsibility for implementing the provisions of the Act and "to ensure that society and the environment are protected from the adverse effects of surface and sub-surface coal mining operations."

Jan 1, 1979

By H. Wesley Peirce

Although not generally recognized, Arizona has rock salt deposits unique in the United States. This uniqueness stems from a combination of two factors: (1) relatively youthful geologic age and (2) nonmarine origin. Although Arizona shares one deposit with Nevada (Figure 1, No. I) there are three others within the State (Nos. 2, 4, 5) that are believed to be both late Cenozoic in age (less than 15 million years) and nonmarine in origin. The only other recognized nonmarine salt deposits in the U.S. are much older, being in the early Cenozoic (Eocene) Green River Formation of Colorado and Wyoming. According to Johnson and Gonzales (1), the remaining rock salt deposits in the United States are marine and either Paleozoic or Mesozoic in age. Of the seven localities shown in Figure 1, six in the Basin and Range geologic province are believed to represent nomarine late Cenozoic phenomena and one (No. 7) in the Colorado Plateau geologic province is Paleozoic (Permian) in age and marine in origin. The following comments are intended to update the general geologic highlights of these deposits and to summarize the nature of their present utilization.

Jan 1, 1979

By Hajime Kitamura, Nobuharu Isago, Yuta Yamanishi, Kosuke Kawata, Hiroshi Yagi, Akira Matsuoka

Mountain tunnels are generally considered to be stable during earthquakes, however, it is known that the portal areas are prone to seismic damages. Characteristics in portals such as the location of the slope, modulus of ground deformation, and the change of overburden are different for each tunnel, and damage degrees are unclear. In this study, we reproduced the seismic behavior to investigate the effect on the tunnel portal by considering some parameters above, using simple static model tests and numerical analysis. As a result, the conditions of the slope condition and minimum distance from slope was confirmed to influence on the mechanical behavior of the tunnel portal during earthquakes.

Dec 1, 2022