Search Documents

By Salama

In the conventional approach, the separator feed incremental masses are assumed to be concentrated at the midpoints of the density or size intervals and subjected to a model partition function. The resulting separation predictions would change if the locations of the incremental masses were changed. As a result. the predicted results depend on the choice of locations where the feed incremental masses are concentrated in the density or size intervals. A technique that utilizes the cumulative-mass-distribution of the circuit feed and the derivative of the partition (separation) function relative to density or size variables is proposed. The proposed technique eliminates the dependency of the predictions on choice of where the feed incremental masses are concentrated within the density or size intervals. Since the proposed technique is based on the cumulative masses at the upper limits of the density or size intervals, the technique produces a single prediction whereas the existing techniques produce predictions that depend on where the incremental masses are concentrated. In fact, it has been demonstrated that the existing conventional technique, in which the incremental masses are concentrated at the midpoints of the density or size intervals, is a first-order approximation of the technique proposed.

Jan 1, 2002

By Ping Xia, Yaoxin Lu

With productivty increment. it becomes very important to monitor the underground production environment. This paper presents a multi-level computer monitoring and managing system, which was specially developed for the mine. In this system, TF-200, Industrial Standard Buses (STD) and 32 bytes Super micro-computer were integrated into one body as hardware; Data Base was designed by means of software engineering method in the software development; on maitenance of the system, the parameters are managed concentratedly and data are classified to process; therefore, the ystem gets to the advanced level in China. The system is composed of four sub-stations: Signal Transmission. Data Collection, Data Processing and Image Display Sub-system. Signal Transmission Sub-system(STSS) A frequency-division transmission method is used. Data Collect ion Sub-system (DCSS) Industrial Standard Buses (STD) is used. It can change data from STSS into suitable form for DCSS, Calculate average value every minute, decide alarm and transmit data to DPSS. Data Processing Sub-system (DPSS) The host is a S/120. With UNIX Operation System. the data from DCSS can be classified. stored, displayed. printed, by means of real-time and time-division processing. Additionally the functions of the historic data search and data analysis are provide. Image Display Sub-system (IDSS) The real-time and historic data was displayed for curves and diageams on screens. This system has been in operation.

Jan 1, 1991

By J. Bigu

A theoretical radiation mine model, suitable for underground uranium nines, has been investigated. In this model, the rate of ventilation and/or the radon (thoron) gas emanation from mine walls are time-dependent. Several cases of practical interest have been investigated including sinusoidal, linear, exponential, stepwise, or a combination of two or more of the above. Analytical solutions were obtained for the time-dependent radon (thoron) gas emanation rate. However, because of the extreme analytical complexity of the solutions corresponding to the time-dependent ventilation rate case, numerical solutions were found using a special Runge-Kutta procedure and the Hamming's modified predictor-corrector method for the solution of linear initial-value problems. The mine model makes provisions for losses of radioactivity, other than by ventilation and radioactive decay, by, say, plate-out on mine walls, and by other mechanisms. Radioactivity data, i.e., radon, thoron, and their progeny. obtained with the above mine model for a number of ventilation and emanation conditions, are presented. Experimental data obtained in an inactive stope of an underground uranium mine for a time-dependent air flow case are shown. Air flow conditions (ventilation rate) were determined by tracer gas techniques using SF6.

Jan 1, 1987

By C. P. Lazzara, F. J. Perzak, C. C. Hwang, C. D. Litton

Fire development and spread along conveyor belts in ventilated ducts were investigated experimentally and theoretically. Various types of conveyor belts used in mining applications were ignited and burned in a full-scale gallery under various flow conditions. The flame spread rates depended strongly on the ventilation air speed. The time-temperature traces of gas and belt obtained at 12 feet from the entrance show that a rapid belt surface temperature change takes place prior to a change in the gas temperature, indicating that radiative heat transfer from the flame to the belt surface plays an important role. Further, anomalies in the flame spread rate in the vicinity of 1.5 m/s air speed (i.e., much greater rate than that observed at either higher or lower speeds) can be explained through the mechanism of flame tilt and the resultant view factor between the flame surface and the belt surface. In order to correlate the fire spread with material properties of the conveyor belts (such as the specific heat, the thermal conductivity, and the pyrolysis temperature) and the fire environment (such as the gas temperature and the ventilation air speed), a theoretical model has been developed. This model is based on the experimental observation that the radiative heat transfer is the dominant mode of energy transfer ahead of the flame front. Agreement between the theory and the experimental results is good.

Jan 1, 1991

By D. M. Walters, C. M. van der Vyver, L. J. deVulliers

The occurrence of underground fires in narrow tabular ore- bodies where high density timber support is used is a dangerous and disruptive occurrence. The containment and extinguishing of the fire remains a very important consideration in reducing not only the loss in production time but also in limiting the extent of the area damaged by the fire. Mindful of this, Gold Fields have adopted and developed the inert gas generator system from its origins in Poland for use in Group precious metal mines. The system generates an oxygen- deficient atmosphere which is introduced in the fire area after this has been sealed. A number of problems had to be overcome to operate this system successfully within the infrastructure of these mines. Of particular significance is the operation of a jet engine, the prime component of the system, at air pressures encountered below sea level. The modifications have been found to be satisfactory to the point where, since 1992, ten underground fires have been extinguished using this system. Invariably, the areas affected by these fires were extensive (over 1 000 000 m3) and required continuous operation of these units over extended periods of time (in some cases in excess of 400 hours).

Jan 1, 1997

By M. K. Gangal, E. D. Dainty

The paper describes the capabilities of a micro-computer-based real time data acquisition system for monitoring and control of mine environments. Applications of such a system for monitoring the ventilation and air quality of a mine is outlined. The paper discusses the results of running a monitoring system with various environmental sensors in a simulated mine environment. The sensors used in this study are: carbon monoxide (CO), carbon dioxide (C02), nitric oxide (NO), nitrogen dioxide (NO2), sulphur dioxide (SO2 ), methane (CH4 ), air flow, absolute pressure, temperature and relative humidity. A performance evaluation of the monitoring system and sensors is presented.

Jan 1, 1987

By Randhir Sehgal

If the primary purpose of a control system is to assure a fixed-quality product at maximum yield, the real issue involved in control of the fine coal cleaning circuit in a plant is to demonstrate that control is technically feasible and economically beneficial . This paper suggests that it is not easy to do so in most cases. Fine coal, defined here as the 28 mesh x 0 fraction of the plant feed, is generally cleaned using a combination of hydrocyclones and flotation. Both of these processes are relatively insensitive to changes in operating variables. Further, the fines fraction general 1 y forms no more than 20% of the plant feed and, at times, is as low as 10%. The instruments to measure flow rates, densities, and product qua1ity (ash, sulfur, etc.) are not sufficiently accurate to allow effective responses to changing state variables and product quality. It is sufficient to run the fine coal circuits at maximum recovery, and the control of product quality and optimization of yield should be achieved by controlling the coarse coal circuits and measuring the quality of the entire clean coal leaving the plant. This contention is made with particular reference to U.S. plants cleaning coal for the utility industry and should be viewed in this context only. It is explicitly admitted that this strategy is mathematically non-optimal in the sense that all size fractions are not necessarily cleaned at equal elementary ash, and would result in a loss of yield. However, under the conditions of conventional coal cleaning practice, this is a sensible approach.

Jan 1, 1988

By K. C. Jordi

Many systems which are modelled mathematically result in a model where the relationships between some or all of the parameters are found to be non-linear. These systems are usually complicated further by a desire to make the system achieve multiple and often conflicting objectives or goals simultaneously. Rozwadowski (1970) developed a model to describe the total discounted net profit of a mine as a function of the amount of ore developed and of the grade of the amount of ore mined. Dynamic programming was used to determine the policy which gave the maximum net present value. In this paper it is shown that the relationships between the variables can be approximated by piecewise linear functions. This is amenable to solution by an algorithm based on the simplex algorithm of linear programming. The goals of maximizing the net present value, the total net profit and the total gold output are incorporated simultaneously into a goal programming formulation of the system. The resulting model is characterized by a large number of disconnected constraints. These are decomposed into several smaller problems and the problem solved. The solution is examined to discover the sensitivity of the system to changes in certain parameters. In particular the interaction between the three goals is analysed to determine whether there is conflict between any of the goals and, if so, what the trade-offs between the conflicting goals are.

Jan 1, 1979

The most important event affecting the United States coal industry in 1993 was the strike by the United Mine Workers of America (UMWA). This was a series of selective strikes, beginning with a strike against four Peabody Holding affiliates on Feb. 2, following unsuccessful contract negotiations between the UMWA and the Bituminous Coal Operators' Association (BCOA). Although that strike ended on March 3, the failure to reach a new contract agreement led to walkouts at several Midwestern mines on May 10. During the summer, the strike expanded to include mines of 13 companies in seven states including Ohio, Pennsylvania, Illinois, Indiana, Kentucky, Virginia and West Virginia. About 17,000 miners were idled during the strike. As the prospects for a settlement diminished, the Secretary of Labor appointed a federal mediator. The mediation resulted in a five-year contract. In addition to increases in wages and pensions, it was agreed that 60% of new job openings would be filled by laid off and active UMWA miners. In return, companies won the right to establish more flexible work rules and scheduling of miners. While some health care benefits were expanded, the agreement established a new health care system that was designed to reduce costs. Preliminary Energy Information Administration (EIA) data indicate that US coal production fell by 5% in 1993, to 859 Mt (947 million st) (Table 1). The strike was one of the primary causes of the decline in production. Another significant cause was a 27% decline in coal exports. Also, a very small displacement of domestic coal production resulted from a rise in coal imports.

Jan 1, 1994

By Jack S. McPartland, Gene E. McClelland

It is advisable, for any heap leach project, to develop an historical metallurgical data base to predict production heap performance before ore is mined and placed onto the heap. A data base would include results from: interval assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples; and those results plus column leach test data on diamond drill core or bulk ore composites. Subsequent larger scale heap leach test data can then be compared to the historical data base, to blast hole composite data during mining, and eventually to production data. This paper does not discuss metallurgical comparisons between assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples, but does discuss metallurgical comparisons from bottle roll tests, laboratory scale column leach tests, and pilot scale heap leach tests on core and bulk ore samples with operating data for three U.S. commercially producing heap leach operations. Provided that representative core or bulk samples are used for evaluation, heap leach test results accurately predict or understate the success of the commercial operation and remove most of the uncertainty from the investment decision.

Jan 1, 1990

By A. Pavlides

The purpose of this work is to conduct a preliminary analysis of the spatial variations of the thickness of lignite layers in the area of the Amyndeo mine, and to estimate the lignite reserves of the mine. The reserves are estimated by the method of the Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. The experimental semivariograms are evaluated for both data sets in different spatial directions. Two possible theoretical models for the experimental semivariogram (the exponential and a novel Spartan model) are compared and discussed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging precision. The performance of kriging interpolation is discussed in terms of cross validation measures.

Jan 1, 2007

By M. Rîsteiu

The authors aim to analyze the behavior of smart sensors using Transmission Control Protocol/Internet Protocol (TCP/IP) infrastructure in hazardous applications, because of their advantages regarding safety, expansion and Quality of Service (QoS). Initially, some constraints are discussed for these applications. Then, the possibility is analyzed of using 2.4 GHz TCP/IP based transmission for sending data out of an industrial area. In this setup the authors evaluated the round-trip implementation (which requires a database of packet lengths), related to the delay introduced by the radio transmission algorithms from 802.15.4, and 802.11d/g protocols. Tuning results of different varying time-delays were compared to the constant delay cases from the literature (Deák, 2003; Lincoln, 2003). Both the hardware and software setups are implemented. Based on TinyOS specific software for hardware checking/ initiating communication/ starting/ closing measurements the authors have developed separate/combined procedures for testing the integrated devices. Measured time delay is presented and analyzed, for both beaconed and non-beaconed 802.15.4 transmission, with power optimization criteria. By testing two different implementations (Zhang et al., 2001), (ATmega256 RZAV - 256KB flash memory, the CC2420 IEEE 802.15.4 and ZigBee-compliant RF transceiver core - 128KB flash memory) the authors have found some time delay variations as a result of local processing by the ZigBee controller with an amount of flash memory. The work is also focused on adapting industrial measuring standard systems to the smart sensors, but not only through the 4-20 mA standard.

Jan 1, 2008

The advantages of quantitative environmental risk assessment techniques over the more commonly used qualitative approach is widely accepted. One important parameter related to the level of risk is the extent and geographic spread of pollutants. Geographic Information Systems (GIS) provide a powerful and highly flexible tool that increases the sophistication of the risk assessment methodology. Through spatial representation, the estimated risk becomes more comprehensive, thus facilitating the decision making process. In addition, valuable qualitative information can be incorporated into the risk assessment procedure with the help of GIS. This paper illustrates a methodology for quantifying risks posed to human health, by exposure to contaminated land, in a manner, which gives a measure of the uncertainty in the assessment and preserves the spatial distribution of the risks. The case study utilised to illustrate the methodology is a large industrial area around a number of decommissioned minerals production and processing sites with known high heavy metal loads at Lavrio, Greece. The spatial distribution of Pb concentration in soils was derived from 425 soil samples collected over a total area of 120 km2. Indicator kriging was used to quantify the spatial distribution of the risk and related uncertainty and the results displayed in map form using GIS.

Jan 1, 2003

By J. C. Reid

Computer-aided lithogeochemistry was used to "prospect" for stratabound scheelite (a tungsten ore) that occurs in many Precambrian clastic and chemical rocks, northeastern Brazil; The district is a metallogenic province covering about 5000km2. Exploration bedrock lithogeo-chemistry was applied at regional, local, and mine scales to identify regional tungsten trends and dispersion halos associated with economic tungsten mineralization. Regional coarse-mesh sampling (Cu,Mo,W) in 25km2 cells "found" all major mines and significant prospects using objective and cost objective computer mapping of bedrock geochemical data. The method is efficient ; of the 3600km2 study area only 9% of the original area remained after the initial pass. Of this area, the geo- chemically highest ranked (4%) cells contained the mines and prospects. Similar computer-aided treatment was applied to Cu,Mo,W,F, and Be lithogeochemical data from several mining concessions and prospects with outcropping and subsurface W mineralization. At a local scale out-cropping W mineralization was recognized at a distance of 500m. Fracture zones through which hydrothermal solutions traveled were identified; these were related to W mineralization at a depth of 200m.

Jan 1, 1986

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By Vinton A. Garbesi

INTRODUCTION The placing of the monolithic concrete lining of the Bi-County water tunnel illustrates the state of the art in the materials, equipment, methods and productivity available to the industry for this type of construction. This paper describes the management and engineering rationale used by Clevecon, Inc., a subsidiary of S & M Constructors, Inc., Solon, Ohio, in developing the concrete mix designs, the design of the specialized equipment, and the methods used in the manufacture, transport, and placing of the lining. Also discussed are the changes to the reinforcing steel design instigated to facilitate its handling and placing, as well as to enhance the quality of the lining. The intent is to bring to the attention of designers the effects certain design aspects have on the construction of reinforced concrete tunnel linings, as well as indicate the areas where research and development effort should be expended to further reduce costs for this type of construction. GENERAL DESCRIPTION The Bi-County Water Tunnel West is a water transmission main owned by the Washington Suburban Sanitary Commission of Hyattsville, Maryland. The facility was designed by A. A. Mathews Division (formerly STRAAM Engineers, Inc.) CRS Group Engineers Inc., Rockville, Maryland. It is to be utilized as the central feeder of potable water for the northern suburbs of Washington, DC, extending some 4,597 meters from a riser shaft at its western terminus to the eastern interface, with a similar tunnel which extends eastward about 5,180 meters; the majority of its length being under Interstate Highway 1-495. The excavated and finished diameters are 3.8 and 3.05 meters respectively. The reinforced concrete

Jan 1, 1981

By F. Soumis

This paper describes an integrated procedure for the very short term production planning of an open pit and the execution of this plan: the truck dispatching. Integration of plan and dispatch means that the plan is realistic so that its objectives can be realized by the dispatch. This realism is obtained by supplying the plan optimization, which involves mixed integer programming, linear programming and non-linear programming, with experimental O.R. models of waiting and blending. The arrangement of these models in the computer programm has made it possible to obtain very short computing time for the planning in spite of the width of the optimisation. The dispatching of a truck is made by solving a classical assignment problem for each dispatch over a horizon of the expected*next 10-15 trucks to request dispatches. This deep-reaching dispatch procedure uses the continuously arriving information about trucks' positions and shovels situations and models by probability functions the expected waiting time of shovels and trucks. In this manner trucks and shovels are synchronized and last moments' opportunities for productivity gains can be obtained. The dispatch procedure takes .5 second on PDP11. This integrated planning and dispatch procedure gives high productivity while ensuring good blending. Results from the Mount Wright mine of the Quebec-Cartier Mining Co., where the integrated procedure has been installed on the existing computer equipment PDP11, are included.

Jan 1, 1989

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

By Mortimer J. Richardson

Dredging can be traced to early times where it may have been derived by the Phoenicians prior to the 4th century B.C. The first tangible design drawings of a bucket ladder (BL) dredge can be found in the collections of Leonardo da Vinci (1452-1519), which he produced when he was attempting to create better methods of channel and port dredging. The perfection of the system did not commence until after the invention of the steam engine in the early 1800's; providing the impetus to progress from man-powered mud mills, horse drawn along polders or dikes in the Netherlands, England, France and Germany, to steam-driven. In the 1860's following the various gold rushes in the U.S., Australia, New Zealand, Siberia and South America, with placers in particular, efforts were begun to apply mechanization to achieve deeper digging. There is a recording of a dredge being installed to mine gold in Montana in the 1860's but did not include a processing system. Then in the 1880's in New Zealand, some practical engineers developed a system that is said to be the first bucket ladder mining (BL/M) dredge for mining gold placers. In studies of the New Zealand gold dredging experience, it is estimated that some 500 dredges were built to mine gold between the 1880's and 1942. A careful analysis of the data, however, shows that very few were profitable. The technology appeared to stagnate in the early part of the century. Two of the BL/M dredge design engineers left New

Jan 1, 1992