Search Documents

By C. M. F. Viera

In this work the properties of a clayey ceramic incorporated, up to 10 wt.%, with three types of wastes from a water treatment plant was evaluated. To determine the physical and mechanical properties such as linear shrinkage, water absorption and diametrical compression, specimens were prepared by 18 MPa uniaxial pressure and then fired in laboratory furnace at 700oC. The results indicated that the wastes incorporation changed the properties of the clayey ceramic. From the results it was found it possible to recycle these wastes into clayey ceramic in low amounts to avoid deleterious effect on the quality of the fired product.

Jan 1, 2008

By Byung-Su Kim

Most electric arc furnace dust (EAFD) treatment processes employ carbon as a reducing agent for the zinc oxide in the EAFD. In the present work, the reduction reaction of zinc oxide with carbon in the present of various additives was studied. The effects of temperature and the additives of calcium carbonate, magnetite, and mill scale on the kinetics of the reduction reaction were measured in the temperature range of 1173 K - 1373 K under nitrogen atmosphere using a weight-loss technique. The mill scale is one of byproducts generated from the steel rolling process. From the experimental results, it was concluded that all three additives accelerates the reaction rate of zinc oxide with carbon, but the effect of addition of calcium carbonate is the highest. It was also found that magnetite, mill scale, and calcium carbonate in the reduction reaction of zinc oxide with carbon promotes the carbon gasification reaction.

Jan 1, 2006

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

Convential smelting of copper - cobalt - iron sulphide concentrates result in th eoxidation of cobalt and iron, which are subsequently lost into the slag. The emission of SO2 bearing gas from smelting causes serious health and environmentsl problems. In this investigation, three different types of copper - cobalt - iron sulphide concentrates, derived from froth flotation, were investigated, the concentrates, each containing more than 40 wt % percent gangue material, were directly reduced in the presence of lime and corbonin the temperature rnage of 1073 K - 1573 K, fo rthe production of an alloy containing copper, cobalt and iron. We demonstrate the basic principles of process physical chemistry for the recovery of alloy by carrying out a detailed process analysis utilising the predictions from thermodynamic equilibrium and results from the kinetics of reduction reaction. The effect of temperature on the reduction kinetics and alloy formation were determinedand analyzed in detail.

Jan 1, 2012

By Murray Johnston

New measurements have been made on the equilibrium distribution of selenium and tellurium between molten slag and metal phases. Distribution coefficients of Se and Te between magnesia-saturated calcium ferrite slag and copper or silver alloys were measured over the temperature range 1473 and 1673 K under controlled oxygen patrial pressures of 10-11 to 10-0.68atm. The results demonstrate that the minor elements are present in the calcium ferrite slag as the selenide (Se2-) and telluride (Te2-) respectively, up to a PO2 of 10-6 atm. As conditions become more oxidising, Te undergoes a transition to the divalent oxide whereas Se does not. Increasing the temperature was found to enhance partitioning of the minor elements to the slag. In terms of activities, at 1573 K, Se showed strong negative deviation from the ideal behaviour in the slag, while Te showed only slight positive deviation.

Jan 1, 2006

By S. C. Flood, J. D. Hunt

"The columnar-equiaxed transition (CET) has been studied numerically under unsteady-state conditions using mathematical models that: (i) include a non-equilibrium undercooling at the columnar front;and(ii) describe the simultaneous evolution of the columnar and equiaxed zones.The results are discussed and compared with those produced by a steady-state analysis.IntroductionThe majority of the previous work on the columnar-equiaxed transition (CET) has concentrated on the production of equiaxed nuclei, regarding this as being the critical step in the formation of an equiaxed zone. Recently, the growth of equiaxed grains has been considered and this is not unreasonable because, for an equiaxed zone to be present, the grains must grow as well as nucleate. Since the growth rate of the grains will be determined by the thermal environment at and ahead of the columnar tips, it was decided to model the liberation and flow of heat during solidification to discover whether the various trends in the columnar range might be explained by their effect on the temperature profile throughout the casting. The models presented here for the solidification of a casting are the first to include the latent heat liberated ahead of the columnar front. Burden and Hunt (1) consider its effect only qualitatively, and although Lipton et al (2) adopt a criterion for the CET which is based on the thermal interaction of the columnar and equiaxed grains, they do not actually include the latent heat in their calculations.It can be argued that the latent heat liberated by the equiaxed grains in the bulk will retard the columnar dendrites in a casting: once the equiaxed grains are sufficiently well-established, the latent heat that they evolve could slow down the columnar growth to such an extent that the equi axed would dominate. Alternatively, the latent heat produced by the equiaxed grains might suppress further equiaxed solidification by raising the bulk temperature. The nature of the thermal interaction between columnar and equiaxed growth is not obvious, and because it is dependent on the material parameters and the dimensions of the system, it cannot be considered effectively in a qualitative way but has to be studied quantitatively: hence the need for the mathematical models discussed in the following pages. The results of the models are discussed in the light of a steady state analysis."

Jan 1, 1986

By Jan A. Aune

The paper describes a number of electric furnace equipment modules especially developed or modified for slag furnace applications. Both the resulting design concept for a modern electric sulfide smelter and some of the changes in traditional process-concepts made possible are outlined.

Jan 1, 1983

By A. V. Tarasov, A. D. Besser

A processing flowsheet has been developed for treating substandard lead-containing polymetallic bulk concentrates and intermediate flotation products containing precious metals, which comprises oxidizing roasting in a calcination kiln and electrothermic smelting generating low volumes of off-gas. The proposed flowsheet also incorporates a dust collection system and sulfur dioxide recovery from off-gas. It is proposed to implement this process by using a reaction smelting technique. For this purpose, the charge to be fed to the smelting furnace after its calcination in a drum-type rotary kiln must have a ratio of sulfide sulfur to sulfate sulfur of at least 1 :2. Electric smelting makes it possible to produce lead bullion that also collects the precious metals contained in the feed, as well as copper-lead matte and slag containing zinc. The recovery of lead into lead bullion and into matte is approximately 83% and 14%, respectively (thus the overall recovery is 97%); the total recovery of gold and silver into lead bullion and matte is 98%; th\lt of copper into matte is 89%; the recovery of zinc into slag is 96%; and that of sulfur into sulfuric acid or gypsum is 90%. After the recovery of zinc from slag, the latter can be utilized in the construction industry.

Jan 1, 2000

By Luben Xie, Lin Hu, Qiang Wang, Min Gan, Tao Jiang, Wenqi Li, Yi Wang, Xiaohui Fan

"The mineralization behaviors of typical fluxes are studied by investigating the microstructures with optical microscope. The results show that the reactions begin with between iron ore and lime, limestone with small particle to form primary liquid. Then coarse limestone, dolomite and serpentine take part in reaction under the action of primary liquid. Limestone is the easiest to mineralization, next dolomite, and the last is serpentine. The higher basicity and smaller fluxes size favor the mineralization process of dolomite and serpentine.IntroductionThe purposes of adding fluxes into sintering are that:(1) to increase the basicity of sinter, so as to reduce even eliminate addition fluxes into BF(blast furnace) and decrease the coke ratio of BF[1,2]. (2) to decrease the melting point of sintering mixture to ensure sintering can be carried out at a lower temperature and reduce the energy consumption. (3) to improve the qualities of sinter by forming binding phase with iron ore fines [3].Flux is another significant component for sinter besides iron ore, especially for high basicity sinter[4]. The proportion of flux is usually higher than 10% in sinter mixture(excluding return mine).There were many reports about the influence of the flux types on sintering, such as limestone, dolomite, lime and so on[5-7]. It is very important to choose suitable fluxes for iron ore sintering. Although the effect of flux size on sintering also has been researched, the mineralization behaviors of the fluxes in the sintering process has not been illuminated. The paper will study the mineralization behavior of fluxes in sintering."

Jan 1, 2011

By Masafumi Maeda

Our aim in this project was to develop a new copper refining technology utilizing pyrometallurgical treatment and a raw materials preparation technique. In the recycling process; raw material is not an idealized concentrate of copper sulfide but is composed of various types of scrap, industrial wastes such as sludge, ash and slag, and municipal wastes. Since we cannot expect oxidation heat in this process as in sulfide smelting, organic materials are viewed as an alternative energy source. Quality of the copper produced is targeted as 99.99% and an intermediate grade will also be marketable. To benefit the plant, rare metals and other nonferrous metals will also be recovered The overall system is described in this paper, specific topics outlined and preliminary research presented. Current Japanese technology for recycling copper based materials is briefly reviewed.

Jan 1, 1995

By Honggang Zhong, Wei Du, Qijie Zhai, Junjie Sun, Jingzheng Ye

"Effects of pouring temperature and cooling water flux on solidification structure of ferritic stainless steel are investigated with a thermal simulation setup. The results show that with pouring temperatures 1518° C, 1528° C, 1538° C and 1548° C, both Lmean (the mean length between columnar to equiaxed transition(CET) position and chill surface of the samples) and the mean dimension of equiaxed grains increase. On the other hand, with cooling water flux 400, 800, 1200 and 1600mL/min, Lmean gradually increases, and the mean dimension of equiaxed grains decreases. In addition, low pouring temperature and cooling water flux enlarge the ratio of fine equiaxed grains.IntroductionFerritic stainless steel plays an important role in industry products nowadays. Compared with austenitic stainless steel which contains both chromium and nickel, ferritic stainless steel can obtain good corrosion resistance despite the absence of nickel [ 1]. F erritic stainless steel has been widely applied in automotive exhaust systems [2], electrical equipment, construction and chemical industries and also has broad development prospects. At present, continuous casting technique has developed into an important technology applied in iron and steel making. The solidification structure of continuous casting slab has significant influence on the final properties of stainless steel. The developed columnar grains of ferritic stainless steel would result in negative effects on mechanical property [3]. However, fine and homogeneou& equiaxed grains can improve the comprehensive properties of ferritic stainless steel [4] Therefore, it makes great sense to promote the columnar to equiaxed grain transition (CET). Recently Baosteel has developed a new type of Cr-saved ferritic stainless steel, but the effect of continuous casting conditions on its solidification structure is unknown. It is important to investigate the effects of solidification conditions on solidification structure of this new ferritic stainless steel, which can give guidance for optimizing the production process."

Jan 1, 2014

By Jianhong Dong, Min Chen, Cuihuan Huang, Bo Li, Nan Wang

"Scale layer can be formed on the slab surface in the areas of secondary cooling and strand discharge during continuous casting process. From 1000 °C -1200 °C, the influence of steel composition on the stable oxide phases inside scale layer, particularly the types of alloying elements including aluminum, silicon and chromium, is investigated under different partial pressures of water vapor by the calculated predominance diagrams of iron oxide as well as its intermediate compounds formed with other metal oxides, and the stable oxide phase composition within scale layer under the working condition of secondary cooling is discussed. At lower partial pressure of water vapor, only a iron spinel (or ferrosilicate) phase is the stable phase with any alloying element contents in steel composition, whereas the stable phases are FeO and iron spine! (or ferrosilicate) inside the scale layer at higher partial pressures of water vapor .IntroductionOxide scale formation on the surface of cast and rolled products because of oxidation by the surrounding oxidizing atmosphere is a significant disturbance factor in steelmaking. The yield loss of iron because of scale formation is considerable during continuous casting and hot rolling process. Surface quality more often is impaired by scale property, which increasing the difficulty of quality assurance, dimensional accuracy and performance control. Furthermore, a potential source for subsequent surface cracking (hot shortness) can be caused by the enrichment of scrap residuals (Cu, As and Sn) at the steel substrate surface as a result of steel oxidation [1-2]. In flat products manufacture via thin slab casting technologies, these phenomena are particularly pronounced and require enhanced development efforts in descaling efficiency [3].Compared with the scale formation in continuous casting, the quantity of scale formed during hot rolling and reheating in the rolling mill is larger, and control of scale formation and descaling is a long-established task in hot rolling. Therefore, extensive research and development work have been carried out, including the effects of heating and rolling temperature on the thickness and microstructure of scale layer, heating time and furnace atmosphere, cooling mode, and steel composition on the scale formation, more attention has been given to the control of scale formation during reheating and hot-rolling process. On the other hand, hardly any specific efforts and countermeasures are taken in continuous casting, and very less research has been done despite the network-type crack on the as-cast strand surface caused by the subscale enrichment of scrap residuals [ 4-7]."

Jan 1, 2014

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By Neusa Alonso-Falleiros, Aristeu Braz da Veiga, Marcelo B. Mourão, Adriano Pescarmona, Antonio Alberto Froes Schettino, Cyro Takano, Carlos A. S. Giraldo

"The Caron process of nickel extraction from lateritic ores produces a fair amount of an inert residue, the so-called “black sludge”, that is disposed in a dam according to the required environmental regulations. On the other hand, it represents an opportunity to resource recovery. This work presents the characterization of the residue, discusses some possible ways to recover the valuables, and presents experimental results of pyrometallurgical runs aimed at recover nickel as an iron-nickel alloy. It has been shown that the residue contains large amounts of silicon, iron, aluminum and magnesium, in the form of oxides and silicates, and small quantities of nickel, cooper and cobalt, besides several other elements. It has also been shown that gravimetric or magnetic concentration methods do not present promising results. On the other hand, it is possible to obtain iron-nickel alloys by high-temperature carbothermic reduction of the “black sludge”.IntroductionThe Caron process consists of a combined pyro-hydrometallurgical process to extract nickel from high iron limonitic lateritic ores, recovering also the cobalt present in the ore. The main steps are the reduction roasting of the ore, aiming at a selective reduction of nickel and cobalt to the metallic state, avoiding as much as possible iron reduction, followed by leaching with ammonium carbonate solution and the recovery of metal from the pregnant liquor [1,2]. As a result, significant amount of tailings are generated, that are disposed in appropriate dams. This residue, called “black sludge”, contains significant proportion of silica and iron, and also small amounts of nickel, cobalt, cooper and some other elements. Due to diminishing deposits of nickel ore, high metal prices and a significant amount of “black sludge “ available after several years of operation of the plant, Votorantim Metais, who operates a facility in Brazil that uses the Caron process, decided to explore the possibility of recover nickel from the residue. This paper presents the characterization of the residue, and the results of experimental work aiming recovery of nickel from it."

Jan 1, 2008

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By N. A. Warner

To filly secure the environmental and social acceptability benefits of making a sulphide smelting facility and its ancillary sulphuric acid plant or other means for fixing sulphur, a virtually zero gas emission operation, it will be necessary to utilise exclusively technically pure oxygen. The strategy proposed for preventing the smelter from overheating involves highly efficient energy transfer by promoting sulphur trioxide formation at a relatively higher temperature than normal. A closed-loop gas circuit uses an eductor system actuated by the process oxygen to recirculate sulphur trioxide and unconverted sulphur dioxide back to the smelter, the endothermic dissociation of sulphur trioxide becoming a major contributor to the removal of excess heat. The only gases leaving the system relate to the bleed of nitrogen impurity introduced in the tonnage oxygen.

Jan 1, 1998

By Yuanbo Zhang, Qian Li, Helei Zhang, Heng Yu, Guanghui Li, Tao Jiang

"Large reserves of specularite iron ores have been found all over the world, which is characterized by high total iron grade, low gangues content, as well as low commercial price. However, it has not been widely used in sinter or pellet production due to its inferior sintering and roasting behaviors. It has shown that the proportion of specularite ores was increased as high as 40%~50% and good results was achieveed by using Composite Agglomeration Process (CAP), an innovative agglomeration process invented by Central South University. But the mineralization of specularite is still unknown during composite agglomeration processing. In this paper, the induration characteristic of specularite ore is studied by simulating CAP in laboratory, as well as microstructure analysis of CAP product. The results show that specularite pellet is mainly indurated through recrystallization of Fe2O3, calcium ferrite within high basicity sinters matrix interweaves with the recrystallized Fe2O3 on the surface of the pellet, which forms an integral microstructure, and ensures high strength of CAP product for ironmaking.IntroductionLarge reserves of specularite iron ores have been found all over the world, especially in Minas Gerais of Brazil, Xuanhua city and Anshan city of China, Elba island of Italy, St.Gotthard of Switzerland, Cumberland of Britannic, and so on. The specularite ores have a smooth surface, as well as a good crystallization and dense texture. When specularite is used to produce pellets, the specularite ore grains are difficult to adhere onto green ball due to its poor ballability. Moreover, specularite pellet requires high roasting temperature over 1300°C [1]. When specularite ore is used in sintering, the permeability of sintering bed gets bad and the quality of sinter is diminished. The practice in a few sintering plants finds that the output and strength of sinter decrease with the increase of specularite proportion, and the consumption of coke increases [2-4]. Therefore, the utilization of specularite has been limited. Composite Agglomeration Process (CAP) is an innovative technology invented by Central South University [5-7]. The process has the following merits: making reasonable utilization of different iron ore resources; improving the quality and output of sinters; manufacturing sinters with low basicity; significantly reducing energy consumption, etc[8-9]. It has been shown that large proportion specularite ores, as high as 40%~50% can be used well by CAP [10], but the mineralization of specularite pellet is still unknown during composite agglomeration processing. In this investigation, the induration characteristics of specularite ore pellets is studied by simulating CAP in laboratory, and the phase composition and microstructure of CAP product are also characterized by using microscope and Leica image analyzer (Germany, Leica DM RXp)."

Jan 1, 2011

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By William E. Torres

The Southern Peru Limited smelter, in Ilo, operates two reverberatory furnaces, seven Peirce-Smith converters, one Teniente Converter, two casting wheels and a single contact acid plant. The Teniente Converter was commissioned in August 1995 and was designed to smelt 744 dry metric tons (820 dry short tons) of concentrate per day. The process off-gas is collected in a water-cooled hood, cooled in a spray chamber, and cleaned in a Joy electrostatic precipitator for further treatment in the Acid Plant. This paper presents the current Teniente Converter operating practices and control philosophy. Relevant improvements and modifications to achieve a 379 day campaign without tuyere replacement and a daily average smelting rate of 862 dry metric tons (940 dry short tons) of concentrate are discussed.

Jan 1, 1998