Search Documents

By K. A. Lewandowski

Agglomeration of ore can be used to immobilize fine particles during heap leaching by agglomerating them into granules. Without agglomeration, the fine ore particles can migrate within the heap, clogging flow channels and producing large areas where access of solution to the ore is very poor. The benefits of agglomeration are well-known in gold heap leaching operations, which can be effectively agglomerated using binders such as Portland cement due to the alkaline leaching solutions used. However, agglomeration has not been very effective in the heap leaching of copper ores, because these ores require an acidic leaching solution. Acid destroys the effectiveness of most binders, causing the agglomerates to disintegrate as soon as the leaching solution is applied. In order to gain the benefits of agglomeration in copper heap leaching, an economical, acid-resistant binder is needed. The two issues that needed to be addressed were: 1) Lack of effective methods for evaluating binder acid resistance before performing expensive, time-consuming, full-scale heap leaching tests, and 2) The vast majority of known binders react poorly to acid conditions, and so a basis was needed for determining which binders are most likely to be acid-resistant. In this paper, the development of two new tests for evaluating binder acid resistance in the laboratory are described. The ?soak test? determines the degree to which agglomerates disintegrate and release fines on contact with acidic solution, measuring the relative quantities of fines released by agglomerates made with different binders under controlled conditions, and serves as a rapid means for comparing large numbers of binders. The ?percolation test? measures several different parameters to determine how a binder is likely to perform in heap leaching: 1) the degree of ?slump? and compaction of agglomerates as they are wetted by acidic solutions; 2) the hydraulic conductivity of the agglomerate bed; 3) the migration of fines through the bed as the solution flows through it; and 4) the quantity of liquid retained in the agglomerates after they are drained. Using these tests, a broad spectrum of binders were examined. Soak testing determined that the most acid-resistant binders were nonionic polymers. Five of these binders were further evaluated using percolation testing.

Jan 1, 2006

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By Qingcai Liu

The effect of the TiC addition on corrosion resistance of the Al2O3-C refractories in smelting reduction melts has been studied by quasi-station immersion and rotary immersion. The corrosion rate of Al2O3-C refractories is decreased with the TiC addition. The corrosion mechanism of Al2O3-C refractories is oxidization of graphite carbon by the oxides of the melts and the formation of deteriorate layer.

Jan 1, 2006

By M. A. Aziz

The electrochemical performance of a series of carbon materials produced from coconut shells, which are very cheap and readily available in Bangladesh was investigated for their viability as anode materials in rechargeable lithium-ion batteries. X-ray diffraction technique was used to measure the interlayer spacing (d002) of the produced carbon materials. A number of half-cells were prepared with the produced carbon materials from coconut shell as working electrode and metallic lithium as counter electrode with 1MLiPF6 electrolyte in a mixture of ethylene carbonate and dimethyl carbonate. The discharge-charge profiles were measured for the different half-cells by using Arbin 24-channel Cyler. The value of interlayer spacing of the coconut-based carbon material was found to be 0.397 nm at 900°C, which is most suitable for lithium-ion insertion into the carbon structure without any expansion. The specific discharge capacity of carbon material from coconut shell heat treated to 900°C was found to be 1015.65 mAh/g. The coconut carbon material heat treated to 900°C delivered 335.22 mAh/g reversible capacity, which is comparable to the commercial carbon/graphite presently used in lithium-ion battery systems. The irreversible capacity loss and coulombic efficiency in 25th cycle of half-cell made with coconut carbon material were found to be 0.16% and 99.83% respectively. The carbon material produced from coconut shell can, therefore, be used as a potential anode for rechargeable lithium-ion batteries.

Jan 1, 2006

By J. Huot

It has been shown that magnesium-based metal hydrides such as Mg2Ni could be synthesized by high energy mechanical alloying. This process creates a nanocrystalline alloy that has enhanced hydrogen sorption properties due to the high density of defects and grain boundaries. Unfortunately, this process also requires a long synthesis time (up to 100 hours in some cases). In order lo reduce processing time and cost of synthesis, we have investigated the effect of milling at elevated temperature under an inert atmosphere. Milling at high temperature improves interdiffusion of the elements and reduces the number of structural defects such as vacancies, dislocations and internal strain. It was found that by milling elemental powders at 200°C. a complete synthesis of Mg2Ni could be achieved in 8 hours. This synthesis time is roughly an order of magnitude lower than that of the process conducted at room temperature. The hydrogen sorption kinetics and capacity of this material are comparable to Mg2Ni synthesized at room temperature.

Jan 1, 2002

By Rauno Peippo

Horizontal Waste Heat Boiler (WHB), today's proven and dominating technology for copper smelter gas cooling, has been utilized by the industry for over half a century. During this time development has taken place in geometry, flow characteristics, cleaning technology and design details. This development has been driven by improved understanding of the specific process requirements, gained both by wide experience and by utilizing new emerging design tools, like computer flow modeling. It had to wait till mid 90's to unite effective and proven Spring Hammer cleaning technology and the process benefits gained by gas guiding vanes or baffle wall in the copper smelter WHB design. The new design has demonstrated improvement in gas cooling efficiency and the process conditions down stream in form of less dust sticking problems in the boiler and precipitators. Reduced weak acid production has also been reported as a result of the design. The theoretical aspects, computer flow modeling results and actual benefits measured in old smelting line modernization are discussed. Experience £tom modernization projects such as Phelps Dodge, Atlantic Copper, Mexicana de Cobre, and Nippon Mining, Saganoseki, are discussed. In mechanical design there has been development resulting improved gas tightness with less corrosion and better control of dust sulfation. An essential improvement is the integration of the boiler hopper and dust removing conveyor. Having no steel plate casings in the hopper and conveyor section but using of boiler tube membrane instead eliminates thermal expansion differences. The dust conveyor will be effectively cooled against hot dust lumps falling down while the acid dew point corrosion is prevented in the cooler sections of the hopper. Conceptual features are presented of a new generation Copper Flash Smelter WHB presently under construction at Boliden Mineral, Skelleftehamn, Sweden, where the latest development and innovations are adopted.

Jan 1, 1999

By Hebi Yin

A two-dimensional finite element solidification model was developed to simulate the transport phenomena occurring during laser deposition of AISI 410 stainless steel during the Laser Engineered Net Shaping (LENS®) process. The molten pool geometry and the distribution of temperature, solute concentration and velocity were calculated during deposition of a thin wall plate. An analysis of the simulations results revealed the importance of heat transfer by both conduction and convection as well as the roles of the driving forces for convection in the molten pool. The heat transfer and the flow pattern in the molten pool are considerably dependent on the travel speed of the laser beam. For the alloy and process parameters in the simulations, no significant macrosegregation was observed. The temperature-dependent properties and thermodynamic variables involved in solidification modeling were calculated using Thermo-Calc software. The results of this work contribute to the current understanding of transport phenomena in the molten pool of laser deposition processes.

Jan 1, 2008

By Federica Paglietti

In this work is presented SEX (Structural & Elemental X-Ray Instrument), the first spectrometer completely portable which make non-destructive X-ray fluorescence and diffraction analysis, in contemporary and in real time. This instrument has been realized using miniaturized detectors, the same model installed on the mission Pathfinder NASA, and X-ray microtubes. SEX allows the chemical and mineplogical characterization of all kind of solid materials and allows to make chemical stratigraphy and liquids analysis.

Jan 1, 1998

By Yuri Bychkov

The Electron Beam Melting is the most efficient technology for metals and alloys refining. For ,secondary metals processing the Electron Beam Skull Melting (EBSM) with the electromagnetic stirnng (EMS) of melt in the crucible was shown to be the most appropriate. The copper produced by EBSM with EMS possesses higher density and electric conductivity in comparison with other refining methods. The details for high power electrical machines were cast of the copper waste refined by EBSM technology.

Jan 1, 1995

By Ragnhild Aune

In fire refining of copper, the affinities of various impurity elements on dissolved oxygen is of great significance. Further, in the design of oxygen probes in liquid copper, the influence of solute interactions on the activity of oxygen need to be considered in order to evaluate the oxygen concentration in molten copper. The present paper presents a series of measurements of the activities of oxygen in liquid Cu-M-o alloys (where M stands for Mn, Zn, As, Se or Te) carried out by the present group employing the solid electrolyte galvanic cell technique. Extreme care was taken to control the oxygen potentials in the inert gas atmosphere, and to keep the oxygen levels very low in the molten metal. The oxygen content was determined by analysis of the samples taken out from the melt. The results obtained showed that Mn has a strong negative influence on the activity coefficient of oxygen in liquid copper. A similar, but less prominent effect was observed in the case of Zn. Arsenic had no influence on the activity of oxygen in Cu (liq.). Se and Te had slight negative effect on oxygen activities in copper at XO > 10-5, while at lower oxygen levels the interaction coefficients were found to be positive. The results obtained were compared with empirical models for the calculation of interaction coefficients available in literature.

Jan 1, 2003

By Animesh Jha

Univariant diagrams are constructed for the reduction of nickel and cobalt oxide and sulphide minerals. The results from the carbothermic and hydrogen reduction of sulphide minerals are compared. The importance role of lime and calcium sulphate in controlling the emission of sulphurous- gases during reduction reaction is also explained. The mechanism of carbothermic reduction of nickel sulphide is explained by examining the sulphur exchange and reduction reactions. The phase equilibrium relationships that determine the formation of multicomponent liquid are characterised. Also the governing equilibria for inert atmosphere calcination- roasting of nickel and cobalt sulphide minerals are also described for the metallization of nickel and cobalt.

Jan 1, 1993

By R. Moreau, V. Uspenski, K. Messadek, Y. Delannoy

Experiments and numerical simulations have been carried out to investigate the properties of quasi-2D turbulence. A new mercury model experiment has been built and tested in a uniform magnetic field up to 6T, (Ha~ 1000), ensuring a better two-dimensional behaviour than earlier versions (Alboussiere et al., 1997), limited to 0.2T. The quality of the experimental results has been improved in order to get wave number spectra (instead of frequency spectra) and higher signal over noise ratio (due to the higher magnetic fields). In parallel, some two-dimensional "direct" numerical simulations were performed using a commercially available code to solve a 2-D motion equation involving a source term to model the Hartmann layer. This term is derived from the condition of closure of the electric current, which allows to transfer the Hartmann effect into the 2D-core flow without simulating the layer itself (Sommeria & Moreau, 1982). No subgrid scale modelling is needed in such a two-dimensional situation where most of the energy is carried by the large scales.

Jan 1, 1999

By Hirofumi Tai, Masafumi Morishita, Toshiya Miyake

"In order to prevent corner cracks on cast steel slab and bloom, solidification delay at the corners should be controlled at the proper level. For this purpose, controlling the heat flux from the molten steel to the solidified shell at corners is essential. In this paper, optimization of the submerged nozzle was studied based on flow and solidification analysis.First, for the slab caster, the submerged nozzle shape was optimized. The improved nozzle was tested in actual casting and completely succeeded in preventing corner cracks. It was clearly demonstrated that the solidification delay and the corner cracks were strongly affected by the spouting stream from the submerged nozzle.For the bloom caster, on the other hand, the setting angle of the nozzle was optimized. Numerical simulations demonstrated that the spouting stream from the nozzle causes solidification delay, impinging at the corners under electromagnetic stirring conditions. Optimization of the setting angle of the nozzle is a possible means to reduce the solidification delay at the corners for the bloom caster.Related to the numerical analysis of flow and solidification, the effect of the critical solid fraction at the tip of the dendrite structure on the solidification under electromagnetic stirring conditions was studied."

Jan 1, 1999

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By A. Lackner

Using the CFD software package FIRE, the smelting process inside a cyclone reactor is modelled. The fluid flow is calculated 3 dim., using different turbulence models. The effects of design parameters (length and diameter of the cyclone, concentrate feeding tangentially or from the top,..) and operating conditions are investigated. Single particle traces illustrate how to increase particle retention time before the particles reach the liquid film flowing down the cyclone wall. Moreover a two phase flow approach is developed, based on the "Discrete Droplet Model". The position, velocity, diameter and temperature of each reacting particle is described. The results show the advantages of top concentrate feeding, large height/width ratio of the tuyeres and increasing number of tangentially gas inlets.

Jan 1, 1995

By Andre Thess, Oleg Zikanov

"Direct numerical simulation methods are applied to study the influence of a constant magnetic field on turbulent flows of liquid metals. The flow is assumed to be homogeneous and the problem is reduced to the classical case of the turbulent flow in a 3D box with periodic boundary conditions. The main subject of the study is the anisotropy developing in a liquid metal flow affected by constant magnetic field.To investigate the long-time evolution of initially isotropic flow the large-scale forcing is applied to maintain the flow energy at a statistically steady level. It is found that the flow evolution depend strongly on the magnetic interaction parameter (Stuart number). In the case of small Stuart number, the flow remains three-dimensional, turbulent, an approximately isotropic. At large Stuart number (strong magnetic field) the turbulence is suppressed rapidly and the flow becomes two-dimensional and laminar. Very interesting is the intermittent flow evolution at moderate Stuart number. Long periods of almost two-dimensional, laminar behavior are interrupted by strong turbulent three-dimensional bursts.The influence of a constant magnetic field on scalar transport properties of liquid metal turbulence is investigated using the simplified formulation of homogeneous flow driven by an imposed mean temperature gradient. Such a flow consists primarily of two turbulent antiparallel jets providing an effective mechanism for heat transfer. It is shown that the magnetic field parallel to the mean temperature gradient stabilizes the jets and, thus, enhances heat transfer considerably."

Jan 1, 1999

By E. Kozeschnik

A new model is presented for the simulation of the evolution of precipitates in a multi-component multi-particle multi-phase environment The mathematical formulation as well as the physical background of the model are briefly introduced and its capabilities are discussed on the example of a precipitation sequence in a complex steel. Keywords: Modeling, precipitation kinetics, nucleation, growth, coarsening

Jan 1, 2003

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992