Search Documents

By Kenneth N. Han

Ammonia has been found to be an effective leaching reagent for gold, silver and platinum group metals in the presence of appropriate oxidants. Electrochemical and kinetic aspects of the dissolution of elemental gold in ammoniacal solutions have been investigated. The cathodic reaction of aurous di-ammine on the gold cathode has been investigated first. From this investigation, the standard electro-potential of the cathodic reaction .and hence. the Gibbs free energy of formation of the aurous di-ammine were established. The solubility of gold in ammoniacal solutions was also examined in relation to ammonia concentration, temperature and concentration of various oxidants. The anodic reaction of the gold disk in ammonia? in the presence? of various oxidants including oxygen, ozon, hypochlorite, hydrogen peroxide, cupric and cobaltic ammine, and iodine was also examined and the results have been discussed. Excellent dissolution yielding of gold and many other metals, typically better than 95% recovery in 1'-2 'hours of leaching at a temperature ranging 80°C to 190°C has been observed. Test results of the dissolution of gold from elemental state as well as other sources including sulfidic ores and scrap are presented.

Jan 1, 1998

By Mitchell L. Spencer, Viswanathan Panchanathan

"Bonded magnets are important category in permanent magnets. They are made by one of the following processes: compression bonding, injection molding, extrusion, calendering. An overview of the various bonded magnet processes and properties of products made with different magnet materials along with their applications are discussed. The main emphasis will be on the use of bonded NdFeB and ferrite magnets.IntroductionBonded magnets are a major growth area in permanent magnets. Bonded magnets are made by any one of the following processes: Compression bonding; Injection Molding; Extrusion and Calendering [1,2]. Compression and injection molded magnets are rigid magnets. Materials used in calendering process produce flexible magnets. Only the extrusion process makes both rigid and flexible magnets. The binders used for the bonded magnets vary depending on the processes. Thermoset, thermo-plastic and elastomeric binders are respectively used in compression, injection and the calendering process. Extrusion molding uses elastomers or thermo-plastic materials. The most co=on magnetic materials, Ferrite, SmCo, Alnico and NdFeB can be used in any of the above processes either alone or in combination as hybrid magnets. Another material that has been developed for co=ercial application is SmFeN. Making the material has been challenging and it is being used in niche market applications in limited quantitiesIn the extrusion process, a highly loaded compound is used to produce strip or sheet and is continuously extruded through a die. In calendering the granulated compound is rolled to produce a continuous wide sheet. In the compression bonding process a uniaxial pressing force is used. These magnets have higher loading compared to injection molded magnets. In injection molding the material is forced into a mold cavity and has lower loading compared to compression molded magnets [2,3]. Most of the flexible magnets are made using extrusion and calendering processes and the most co=on magnet material is inexpensive ferrite. Flexible magnets have been made using rare earth materials, but on a very limited basis.The major advantages of magnets processed by extrusion and calendering are as follows: inexpensive tooling, automation; practically any 2D geometry; fast production rates; no chipping or breaking; a wide range of properties; on-line magnetization; easy to convert (e.g. cut, punch or shape).Compression bonded magnets are inexpensive to manufacture. They have higher magnetic properties compared to injection molded magnets; however lower than their sintered counterparts. The magnet shape is restricted to simple geometries and they require careful handling. Their isotropic nature allows complex magnetizing patterns."

Jan 1, 2013

By Amy Nelson

In the electrolytic production of zinc, cobalt is removed from the zinc electrolyte by cementation with zinc dust prior to electrowinning. Although the thermodynamics for this reaction are favourable, kinetic barriers to cobalt reduction render the method almost useless in practice unless activators such as copper and antimony or arsenic are added. There is a large body of work studying the effect of these additives, yet the mechanism by which they act is still poorly understood. Even when the target conditions are met, zinc dust consumption is excessively high: satisfactory operation requires up to 300 times the stoichiometric amount of zinc dust. The objective of this work is three-fold: (1) to examine the effects of activators and elucidate the characteristics that make a good activator; (2) to identify new additives that could lead to a more efficient purification process; and (3) to test the new additives with synthetic and real electrolyte solutions. The present paper gives a status report on this project.

Jan 1, 1998

By K. Olsen

As aluminum alloy usage in automobiles grows, there are increasing demands on recycling processes and facilities to deal with mixed alloy automotive aluminum scrap. These processes and facilities strive to produce near virgin aluminum stock, which can be relatively costly and difficult. One alternative is to use physical processing methods to upgrade the scrap properties instead of chemically refining the scrap. The Impulse Atomization Process (LAP, patent pending) is a new process for making metallic and ceramic powders. It can produce fine homogeneous microstructures in scrap aluminum alloys due to high undercooling and rapid solidification. The particles have a very narrow size distribution and are in a convenient form for consolidation. This paper compares and contrasts the microstructural features of Impulse Atomized. and quenched Impulse Atomized powders,' for both AL6061 and a scrap aluminum alloy composition.

Jan 1, 1995

By R. J. Dippenaar, W. H. Van Niekerk

"An injectable lime-based desulphurization reagent for the treatment of liquid iron was developed. Firstly, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na20 to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. Subsequently, pilot plant and full scale industrial injection trials were conducted. It was found that lime-based slags, containing Na20 and CaF2, are able to desulphurize liquid iron efficiently. By the injection of a lime based reagent consisting of 60% lime, 25% soda ash and 15% fluorspar at a rate of 7 kg reagent/ton hot metal, the sulphur level in the metal (115kg) was reduced from 0,07% to 0,01 % within 5 minutes. The lime-based reagent developed in this study was successfully injected, both from a metallurgical and from a pneumatic point of view, on an industrial scale. The mathematical model utilised in this study, can be used successfully to predict the course and extent of desulphurization by lime-based slags. IntroductionMainly due to environmental difficulties encountered with pure soda ash, dry slag formation with CaC2 and high cost when Mg are used as desulphurizers, much incentive exists for the development of an inexpensive, environmentally friendlier desulphurization reagent. As a first step in the development of such a reagent, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na2O to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. This was followed by pilot plant injection experiments in which the kinetics of the relevant desulphurization reactions were evaluated. Finally, full scale industrial trials were conducted. All three phases of the investigation will be discussed with the major emphasis being placed on the kinetic study."

Jan 1, 1996

By M. Patel, A. W. Piper, R. A. Forsdick

"Lead bullion is refined in kettles to remove the contained impurities such as copper, antimony, silver and bismuth. These impurities are removed sequentially by the addition of one, or more, reagents to the bath. Impurity elements react selectively with the reagents to form a dross layer on the surface that is subsequently removed for further processing. Mixing the lead bath using specific impeller designs, which form a vortex to ensure that good contact takes place, carries out the reactions. It is important that the mixing is controlled to achieve the optimum bath conditions and hence good dross grades.This paper presents initial modelling work on the kettle refining process using both physical modelling (Water Models) and mathematical modelling (Computational Fluid Dynamics - CFD). Comparisons between measured plant data and simulation results are given.IntroductionThe refining of lead bullion takes place in hemispherical kettles of varying sizes. It is normal practice to remove the impurity elements sequentially, by the addition of reagents, which selectively react with the impurity element. The impurity element forms a dross layer on the surface, which can be removed for subsequent processing at the end of the reaction period.All the refining stages in the production of lead and lead alloys involve mixing the lead bath, although different conditions are required for each stage. At Britannia Refined Metals mixing is achieved using either 3 or 4 angled or flat blade impellers, which generate a vortex in the central region of the kettle. However, throughout the industry a wide range of mixer types are used which are all trying to achieve the same result."

Jan 1, 1999

By Peter Stiaszny, Andrej Samoilov, Yuri Titovets, Gottfried Hribernig, Nikolai Zolotorevskii

"The model has been developed to simultaneously predict both transformation product portions and mean ferrite grain size from the same common · principles as a result of the austenite decomposition during any cooling path of dual phase steels. The transformation products considered are polygonal ferrite, pearlite, bainite and martensite. The model is based on the classical equations of nucleation-growth theory and also contains some empirical parameters. The chemical driving forces for nucleation and composition of elements at the phase interfaces are derived by computation thermodynamics. The empirical parameters related to the model were determined on the basis of a series of austenite transformation dilatometric curves and grain size measurements for continuous and interrupted cooling of several steel types. The model is aimed to predict phase transformation in the complex cooling conditions of the run-out table of the hot strip mill at YOEST-ALPINE STAHL LINZ GmbH as a part of the computer aided system for prediction and on-line controlling of the mechanical properties of hot-rolled strip.IntroductionThe term ""dual phase steels"" is used to refer to a steel consisting essentially of a dispersion of martensite in a fine-grained ferrite matrix. These steels are of increasing technological interest since they provide a better combination of strength and ductility than any other conventional steel sheet material. The strength is important because it offers an opportunity to produce lighter components, while good ductility is needed to permit easy forming of components. It is generally recognized that martensite plays an important role in determining the strength level of dual phase steels. A full understanding of the role played by the phases in determining such characteristics requires investigating in more detail how to optimize the martensite level of such steels, while maintaining good ductility remains the subject of continued research in the industry."

Jan 1, 2000

By Xia Hong-ying, Peng Jin-hui, Zheng Zhao-qiang, Zhang Li-bo

"Preparation of activated carbon from the walnut shell by microwave assisted steam activation was studied. Influences of the three parameters, activation temperature, activation duration and steam flow rate on the adsorption capacity and yield of walnut shell activated carbon(WSAC) were investigated,optimization process was obtained by the Response Surface Methodology (RSM). The optimum preparation conditions were as follows: activation temperature of 980°C, activation duration of 41 min and steam flow rate of 1.66 ml/min. The optimum conditions resulted in an activation carbon with an iodine number of 1025 mg/g and a yield of 52.17%, while the BET surface area, total pore volume and average pore diameter of WSAC were 1328m2/g, 0.72ml/g and 2.2nm respectively. The study supported the potentiality of comprehensive utilization ofWalnut shell and the benefits of the microwave heating.IntroductionActivated carbons are one of the most important adsorbent materials in modern society because of its abundantly developed pore structure, strong adsorption ability, high surface area and thermo stability. They have extensive application in many industries fields which include gas purification [1], catalyst supports [2] and other pollutants [3]. However, in recent years, the industrial production of activated carbon is facing the problem of raw material scarcity and high cost, which limit to be widely used. Therefore, the selection of an appropriate precursor plays an important role and it has become hot sport to seek cheap raw material to lower preparation cost. As a kind of reproducible resource, the waste from agriculture and forestry is a high-grade raw material for preparing activated carbon due to is high carbon content, such as palm shell [4], rice hull [5], and coconut shell [6]. At present Walnut shell is widely accepted to be a renewable source of biomass. According to statistics, there is more than 1000,000 tonnes of walnut shells are produced in China annually [7]. As a good precursor for activated carbon production, Walnut shell is a major agricultural waste, to make better use of the cheap and abundant agricultural waste, it is proposed for activated carbon production."

Jan 1, 2014

By Felipe Costa Hashimoto Bertin, Jorge Alberto Soares Tenório, Rodrigo de Souza Dalti Pereira, Denise Crocce Romano Espinosa

"The increasing amount of portable devices and their fast obsolescence generates an increasing quantity of discarded batteries. The recycling process of discarded batteries allows the recovery of metals for further use and avoids the contamination of soil and water. Even though there are several researches on the topic, few papers focus on mixed batteries. The purpose of this work is to characterize a mass of collected mixed batteries and study the hydrometallurgical process of recycling. The specific leaching parameters studied were pH, temperature and reduction potential. The specific goal was testing the selectivity of pH for leaching each metal. The results show that the optimal leaching occurs in acid solutions with negative pH at IM of sulfuric acid and at room temperature (25°C).IntroductionThe increasing portability of electronic devices in the past century along with their fast obsolescence produce tons of discarded materials yearly that could be recycled generating new materials for the industry. For example, metals such as cobalt and nickel, that are worth respectively US$ 30.00 and US$ 16.10 per kilogram[l,2] are disposed in urban trash yearly, which means that millions of dollars are thrown away instead of being recovered and reused[3].Besides the obvious fact that the society is throwing money away, most of these metals are toxic for the environment and all mammals, so when badly stored after use they can be found contaminating ground water which will contaminate the entire lifecycle. Some of these metals can cause cancer, serious lung problems and have bioaccumulative properties [4] resulting in lower productions of natural products and maybe death for consumers.So in compliance to new regulations such as the National Solid Residue Politic (PNRS) and the CONAMA-Resolution N°401 from November of 2008[5]- (that follows similar restrictions and regulations as the European directives) all those urban and electronic wastes need to be correctly disposed and treated before being thrown away on local dump sites.In Brazil the national rate of garbage recovery is around 70%, which only 5% is properly recycled, accordingly to the research of the UFSC, also electronic waste grows at 5% per year [6]The present study was motivated by the fact that recycling processes for batteries are not spread through the country and by the fact that most papers do not try to recycle a mixed mass of batteries, but a specific mixture which does not represent the composition of traditional household wastes."

Jan 1, 2014

By Sergio N. Monteiro

Jute fabric obtained from discarded sackcloth is a promising low cost and post-used material being considered as reinforcement of polymeric matrix composites. In particular, the combination of this fabric with a recycled plastic constitutes an environmentally correct composite with both economical and environmental advantages. The present work investigates the toughness of recycled polyethylene composites reinforced with up to 40 wt% of post-used jute fabric extracted from discarded sackcloth. Standard Izod notched specimens were impact tested and the results showed an increase in toughness with the amount of jute fabric. Observation of the composite fracture by SEM revealed that the fabric weave, in spite of damages caused by the previous use of the sackcloth, act as an effective obstacle to crack propagation.

Jan 1, 2009

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By J. Brent Hiskey

The global copper industry faces a technological challenge to develop processing schemes for more complex and impure ores and concentrates. Group 15 elements (As, Sb, and Bi) represent impurities that are troublesome both in terms of environmental impact and metallurgical processing. The so-call "dirty" copper concentrates are either unacceptable for smelting and refining or incur high penalties. The behavior of the Group 15 elements is of critical importance in maintaining product quality and process performance. During copper electrorefining, these impurities are released to the electrolyte by electrochemical dissolution of the anode. Depending mainly on temperature, concentration, and oxidation state these elements can spontaneously coprecipitate from the electrolyte. Some of these precipitates are referred to as floating slimes and their formation can have extremely detrimental effects on cathode purity. In this paper, the mechanism of floating slimes formation will be discussed and the fundamental thermochemistry will be reviewed and analyzed in relation to solubility properties.

Jan 1, 2012

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By James E. Hoffmann

This paper briefly reviews the conventional technologies employed for the treatment of copper refinery electrolyte bleed. The strength and weaknesses of conventional practice will be reviewed and a number of process options to address the weaknesses of present process technology will be described and evaluated. The effect of process selection upon energy consumption and the environmental aspects of process effluent control will be discussed.

Jan 1, 1997

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By A. Rosenfeld

The feasibility of applying laser induced optical emission spectroscopy to the high speed sorting of mixed alloy aluminum scrap is investigated. The basic spectroscopy for analysing aluminum alloys for the major alloying elements over their full concentration ranges is established. Materials handling issues are also described and the components of an overall sorting system are presented.

Jan 1, 1995

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By M. R. Jolly, J. -C. Gebelin

"A number of different types of so-called ""filters"" are used in the metal casting industries to impart some cleaning effect and flow control on the liquid metal as it passes through them. The filters range from simple planar meshes through extruded channels to reticulated foam structures and they are manufactured from a range of material going from metals to glass or ceramics. It is most common that software packages used in the industry model the filters by a simple pressure drop associated with some area fraction and permeability parameters.Recent experimental work at the IRC in Birmingham [1] has shown that filters of the same type can behave very differently depending upon the casting process in which they are employed. Modelling filter geometries for a range of different casting processes has indicated that the flow of metal and heat losses through the filters are rather complex and should be considered when using filters in the casting processes. This paper will present a number of cases of different types of filters modelled and different processes and indicate some of the sensitivities of the processes to boundary conditions imposed by the process.IntroductionFilters are commonly used in the foundry industry. The real action of the filters on the liquid metal is not really understood. Some filters are claimed to have a chemical action on the liquid metal or to be able to clean the metal by stopping the impurities or oxides that will result in inclusions in the cast part. However, some recent experiment carried out at the University of Birmingham in investment casting and results available on sand casting [2] have shown that the action of filters may be different in these two processes. As the main difference between these two processes is the mould temperature, the hypothesis of a partial solidification of the metal in the filter occurring in the sand casting process during the primary stage of the filling has been advanced, whereas there is little or no solidification in investment casting. In order to verify this hypothesis, and to reach a better understanding of how filters work, a numerical investigation of the flow and heat transfer in filters in both sand and investment casting has started at the University of Birmingham, in the framework of the FOCAST project. The FOCAST project is an EPSRC project aimed to increase the understanding of the investment casting process. Another issue is the way the simulation packages predict the influence of the filters on the metal flow. The filters are most of the time modelled as porous obstacles characterised by a pressure drop calculated from porosity and some surface ratios or proprietary coefficients. This paper will present the preliminary results of this numerical investigation. First, the different models that have been used are presented, followed by the obtained results. A discussion of these results and their perspectives conclude the paper."

Jan 1, 2001

By S. -H. Jeon, Y. -S. Choi

"The three dimensional current distribution on the rectangular cathode is predicted using a boundary element method with a linear element of trigonal type. The effect of cell geometry and anode shape on current distribution is simulated. Calculated results compare well with experimental results. The proper combination of anode size and distance between electrodes increase the current uniformity.The importance of electrodeposition as a fabrication technology in the electronics industry is large and growing. The main advantages of this wet processing method, in comparison to other dry processing methods, lie in its high yield, rapid processing and low cost. In nearly every application of electrodeposition the pursuit of deposit uniformity, especially thickness uniformity, has been technically imperative. The thickness uniformity of the deposit depends largely on the current distribution over the cathode. The current distribution is primarily determined by the geometrical characteristics of the electrodes and the cell. Also the polarization at the electrode surface and the mass transfer affect the current distribution.The current distribution is an important consideration for those involved in designing electrochemical systems and electroplating systems in particular. Although it is important, the common practice in industry is to use trial and error method to design the cell that optimize the uniformity of current distributions in electroplating. The purpose of this paper is to illustrate the useof boundary element method to predict three-dimensional current distribution in rectangular cell.The calculation of the current distribution is possible by various numerical techniques, which include the finite difference method (FDM)1, the finite element method (FEM)2, and the boundary element method (BEM)3,4. These methods of the numerical calculation have various problems, respectively, but the BEM is considered to be the most efficient. This is due to the fact that the BEM has the advantage of solving field equations only on the surface of a calculation domain. A good comparison between the BEM and the FEM for the secondary current distribution in a Hull cell was made by Matlosz et al.5The fundamentals on the theory of current distribution in electroplating are well-established in the literature by a number of authors.6, 7, 8 However, a small fraction of these works have been specially addressed to three-dimensional analysis, and, mostly thel·10 have focused on the problem qualitatively rather than quantitatively.Extending the previous work to three-dimension, we developed the program for the quantitative calculation of 3-dimensional current distribution using a boundary element method with a linear element of trigonal type. Integrals with singularity from the fundamental solution have been analytically computed and it is shown in detail in the Iiterature11. This paper deals with the three dimensional current distribution for the electrode position of copper in a cubic type cell and the effect of anode shape, size and the distance between electrodes on current distribution is studied."

Jan 1, 1997