Search Documents

By Nobuaki Sato, Tetsuo Fukasawa, Akira Kirishima

To apply the fluoride volatility process for the treatment of fuel debris formed in the damaged nuclear reactors, study on the fluorination behavior of main constituents, such as fuel and cladding is essential. The mixture of uranium and zirconium oxides is formed under severe conditions such as high temperature and oxidizing atmospheres. In this paper, fluorination and volatilization behavior of uranium and zirconium oxides have been studied by TG-DTA method in the presence of fluorine. From the TG-DTA result of UO2 in F2 atmosphere, the weight gradually increased up to 7% at 350 oC followed by rapid weight decrease with exothermic peak showing the vaporization of uranium as UF6. ZrO2 showed similar fluorination behavior to that of UO2. However, fluorination of UO2-ZrO2 seemed to be suppressed with increasing ZrO2 amount. This may be caused by the formation of solid solution.

Jan 1, 2016

By M. K. Yelloji Roa

Effect of conditioning with Thiobacillus ferrooxidans on the floatability of sphaierite and galena has been determined in this work. The flotation behavior of the conditioned minerals clearly shows that such bacterial conditioning does produce marked modification of their surfaces. The variables affecting the surface modification and thereby the flotation response of the minerals were found to be cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Importantly, while the enhancement in flotation obtained due to sulphuric acid treatment was retarded by biotreatment in the case of galena at all cell concentrations due to electrochemical effects, such decrease occurred in the case of sphalerite only at cell concentration sufficiently high for their attachment to the mineral surface. The effect of bacterial conditioning has significant implications to the differential flotation of sphalerite and galena. Mechanisms responsible for the modification of the surface properties of these sulphides due, to bacterial conditioning are discussed.

Jan 1, 1991

By K. P. V. Lei

The U.S. Bureau of Mines investigated a hydrothermal sulfidation procedure to recover lead and silver from plumbojarosite. The plumbojarosite, generated during pressure-oxidative leaching of zinc concentrate in a commercial operation, contained, in percent, 25.4 pb, 18.8 Fe, 1.4 Zn, 29.5 SO,2-, 3.2 s?, 13.4 total sulfur, and 7.4 oz/ton Ag. The sulfidation was conducted in an autoclave and converted the plumbojarosite to amorphous iron oxide and liberated the lead and silver as sulfides. The best operating conditions were using 50 9 of plumbojarosite and 7 pct s? (2.04 9 S? added) in 500 mL of 2.0 mol/L NH3, 150? C, and 1 h. The sulfidation product contained, in percent, 37 Pb, 28 Fe, 6 S2-, 2 SO,2-, and 11.2 oz/st Ag. Ferric chloride leaching extracted 98 pct Pb and 97 pct Ag from the sulfidation product.

Jan 1, 1990

By Fathi Habashi

Laboratory autoclaves for hydrometallurgical investigations are available in a variety of sizes, models, and materials of constructions. They vary in sizes from 25 mL to 2 liters for laboratory studies and 5 to 50 gallons for pilot plant work. They are essential tools for studying aqueous oxidation of sulfide concentrates, dissolution of oxide minerals at high temperature and pressure and hydrothermal precipitation reactions. The maximum pressure and temperature at which any pressure vessel can be used will depend upon the design of the vessel and the materials used in its construction. Since all materials lose strength at elevated temperatures, any pressure rating must be stated in terms of the temperature at which it applies. A review of existing models and their accessories will be given.

Jan 1, 2000

By D. M. Hausen

A refractory siliceous low-grade silver ore (265 g/t Ag) from a prospect in Sonora, Mexico was investigated mineralogically and metallurgically to evaluate extraction of the silver by conventional methods. Approximately half of the silver was recoverable, occurring as coarsely crystalline acanthite (70-300 Am) that was liberated in material crushed to minus 10 mesh. The remaining silver is refractory and occurs mostly as finely locked (-2 to 0.2 Am) acanthite in cherty quartz, and as minor amounts of finely disseminated stylotypite or freibergite in fluorite. The mineralogic data have thus served to explain the 50-60% recovery of silver by flotation and cyanidation.

Jan 1, 1991

By H. Palkowski

Recent trends in the automotive industry lead to increasing interest in advanced high strength steels (AHSS). Those steels often have a high bake hardening potential (BH), giving additional contribution to the strength of structural parts, subjected to the paint baking process. For hot rolled AHSS, namely dual phase and martensitic steels, the effect of process conditions on mechanical properties had been investigated. However, the influence of chemical composition within the range in industrial production has not been investigated sufficiently yet. In the current research, samples with different chemical compositions within the characteristic interval for industrial production are under investigation under different preload conditions and simulating the thermo-mechanical production process. The samples were then subjected to BH process. Tensile tests were performed to study the influence of varying chemical composition on the BH effect. The results of investigations on dual phase steels will be presented in this paper.

Jan 1, 2008

By Bin Xu, Qian Li, Ya-xuan Wang, Yong-bin Yang, Xi Zhang, Tao Jiang

The effects of common associated sulfide minerals including pyrite, arsenopyrite, galena and sphalerite on thiosulfate leaching of gold were studied in this work. Sulfide minerals had significant effects on gold leaching because that the dissolved products of sulfide minerals precipitated on gold surface to form coating layer. The degree of sulfide minerals impact on gold dissolution decreased in the order of pyrite ≈ galena > arsenopyrite > sphalerite, while the degree of effects on thiosulfate consumption decreased in the order of pyrite > arsenopyrite > sphalerite > galena. The additive CMC (Carboxymethyl cellulose) could not only reduce thiosulfate consumption but also increase gold dissolution. The mechanism of this might be that CMC could restrict the decomposition of thiosulfate by cupric ions and the precipitates on gold surface.

Jan 1, 2015

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By Chang Wei, Zhigan Deng, Yizhao WANG, Cunxiong Li, Gang Fan, Xingbin Li

During the process of hematite precipitation, the transformation of Na jarosite convert into hematite has been studied in a batch reactor at different temperatures, ranging from 170°C to 200°C with 3h of the retention time in the presence of 30g/L Fe ( ) and 4g/L Na+. The composition of precipitation was seriously depended on the temperature, at 170°C hematite and sodium jarosite are the reaction products of iron precipitate, with an increasing in reaction temperature the sodium, sulfur content in precipitated decreased and sulfur mainly exist in forms of SO4 2-, and when temperature over 200°C hematite was the only phase in product. An increasing temperature was not only beneficial to iron precipitation, also conducive to jarosite conversion to form high quality hematite precipitate.

Jan 1, 2016

By W. G. Davenport

Chapters 19 and 20 examine direcHo-copper flash smelting and flash converting. This chapter compares the two processes and suggests which is likely to be 'the more economic for a given concentrate. It: (a) uses Chapter 19's direct-to-copper industrial oxygen and oil requirements (b) adds the energy required for electric furnace recovery of Cu from direct-to-copper slag (Czemecki et al 1999) (c) combines Chapter 20's, flash converting calculations with Chapter 18's flash smelting calculations to determine their combined industrial oxygen and hydrocarbon fuel requirements (d) adds the energy required to granulate, crush and dry flash smelting matte for the flash converter (e) adds the energy required to granulate and dry flash converter slag for recycle to flash smelting (f) compares direct-to-copper and flash smelting/flash converting in terms of their total equivalent hydrocarbon ener.gy requirements.

Jan 1, 2001

By M. Cowling, S. Kumarl, A. W. Piper, R. A. Forsdick, C. Bailei, M. Patell

"The lead-refining process takes place in hemispherical vessels called kettles. In these kettles, lead-bullion is mixed at a certain temperature to remove impurities from the melt. This paper presents steps in a novel method for calculating vortex shape and flow field in the refining kettle using Computational Fluid Dynamics (CFD). First of all a two-dimensional axisymmetric model is used to calculate the vortex shape at the liquid-air interface. Here action of impellers and baffles are accounted for by adding source and sink terms to the appropriate momentum equations. The model includes Yolume of Fluid (YOF) method to predict the shape of interface deformation, i.e. vortex. This strategy reduces the computationally intensive three-dimensional transient simulations to a more efficient two-dimensional model. The calculated vortex shape is then used to regenerate a full three-dimensional grid. This grid is used to carry out steady-state simulation using the standard multiple-reference-frame method of impeller-fluid-baffle interaction within the commercial code Fluent. Simulation results for both stages of the development are compared with experimental data.IntroductionOne of the most important steps in Lead Refining process is impeller stirred mixing of Lead Bullion in hemispherical vessels. During this process, the melt is treated with one or more reagents in order to remove impurity elements such as copper, antimony, silver and bismuth. These impurities react selectively with the reagents and float to the melt surface in the form of a powdery layer, which is then skimmed for further processing. Figure-! shows (a) the lead refining kettle and (b) the schematic representation of involved flow pattern. Stirring of the lead bath using specific impeller designs, which creates a central vortex, provides a mechanism for draw-down and dispersion of the buoyant reactants. Clearly, effective control of the impeller generated vortex and flow pattern is crucial to achieving efficient operating conditions."

Jan 1, 2001

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By G. Kugler, M. Tercelj

"The use of the up-to date light alloys and their development are in the sharp ascent especially in transportation industry. In the last years the use of the magnesium alloys for the various purposes was strongly increased. The aim of present research was to study the influence of solidification rate on hot workability and on obtained mechanical properties of AM60 magnesium alloy. The study was also focused on possibility to omit prior homogenisation process which would result in cost reduction. The solidification of gravity cast alloy has been investigated with various methods of the thermal analysis: in situ simple thermal analysis and simultaneous thermal analysis. In order to reveal optimal hot working conditions the deformation behaviour was studied in the temperature range 200-450°C and strain rates between 0.001-lOs-1. Mechanical properties have been studied with tensile and impact toughness testing.IntroductionIn recent years, the increased demand for magnesium alloys has been mainly driven by the need of automotive and transportation industry to reduce the weight, as this is the most important parameter to reduce the energy consumption. Beside their very low weight in comparison to other metals, the magnesium alloys are characterized by good machinability, corrosion resistance and good mechanical properties, and can thus compete with aluminium alloys and for some applications even with steels. Due their decreased workabilty they are typically used as cast alloys, but in recent years also the research of their wrought state has become more extensive [1-7]. Decreased hot workability of magnesium alloys originates from their hexagonal close-packed structure. One of the most popular magnesium alloys with great potential for many applications is AM60 (MgA16Mn), which is predominately used for casting. But its application could be increased if the mechanical properties, could be improved. This can be done by hot working. Namely it is well known that wrought microstructure is characterized by better mechanical properties in comparison to as-cast state. On the other hand due to its low hot workability the homogenization process is required prior hot deformation, which results in increased production costs. Thus the aim of the present research was to study the influence of solidification rate on hot workability of AM60 alloy in order to improve its mechanical properties and to check the possibility of producing near-net-shape casting products omitting homogenisation process by employing small additional deformations after casting. Within the framework of this research the solidification of gravity cast AM60 alloy has been investigated with various methods of the thermal analysis."

Jan 1, 2011

By K. Pagalthivarthi, P. V. Desai

"During solidification of alloys, many inter-related physical processes, such as melt convection, mass diffusion, heat transport, macrosegregation and melt-undercooling occur. Several research workers have studied one or more of these effects separately. To answer important questions on solidification behavior, an overall approach interrelating the processes is necessaryAs a first step toward accomplishing the overall modeling, the freezing of a binary liquid metal is examined. The various stages during freezing of the alloy are critically described to build a continuum model for the entire process. Diffusive mixture theory is used to write the conservation equations for the liquid and the mushy zones. The concept of local thermodynamic equilibrium in the presence of curvature effects is used to restrict the number of degrees of freedom within the mushy zone. Constitutive equations relating flux quantities and affinities, the governing differential equations and boundary conditions are discussed briefly for the freezing process.IntroductionA solidification study encompasses such facets as solifidication time, microstructure, macrosegregation of the solute, shrinkage effects and soundness of the casting. Influence of one or more of the coupled heat and mass transfer phenomena such as local solute redistribution, thermosolutal convection, melt undercooling at dendrite tips and heat dissipation to the ambient have all been previously examined [1-3J. Several studies have examined the individual facets of alloy solidification as isolated processses. In fact, the transport processes occur simultaneously and a comprehensive model should include their inter-relationships. In particular, some of the existing studies of the mushy zone [4-6J do not emphasize thermodynamic completeness. This work represents an attempt to develop a thermodynamically consistent model of the entire solidification process on physical grounds."

Jan 1, 1986

By Blas Melissari, Stavros A. Argyropoulos

"In this paper a computational approach was employed to estimate the melting of solid spheres immersed in different liquid metals and under different convective conditions. The spheres are made from the same material as the liquid metal. The SIMPLER algorithm was implemented using a three-dimensional system in Cartesian co-ordinates. Experimental validation of the dimensionless correlation was carried out in two fluids with vastly different Prandtl numbers. The dimensionless heat transfer coefficient (Nusselt number) is obtained as a function. of the Reynolds and Prandtl number.IntroductionThere is a paucity of dimensionless convective heat transfer correlations applicable to fluids like liquid metals. The existing correlations cover single Prandtl number metals [l] or at most two different Prandtl number metals [2]. A knowledge of heat transfer rates from particles at high flux levels has become increasingly important to the design of energy transfer systems. Melting of solid particles has been studied extensively as it relates to many engineering and environmental applications, such as materials processing, space applications, water resource and energy conversion. When objects are immersed in a fluid with a temperature higher than their melting point, they melt and produce molten material that then mixes with the surrounding fluid. These objects experience not only size variation but also changes in their shape. This observation is more pronounced when the melting occurs in a forced convective flow.Yuge performed pioneering experimental work on the heat transfer from a sphere to air under mixed convection [3]. He suggested procedures for predicting the Nusselt number. Hieber et al [4] studied the spherical system analytically, but their study was limited to flow with small Reynolds numbers. Many researchers studied the melting dynamics of ice spheres in water at different convective regimes. Aziz et al [5] and Hao et al [6] performed measurements of the heat transfer coefficient in the water system by measuring the melting time of ice spheres in forced convection. Hao et al [7] performed visualization studies of ice spheres melting in water under mixed convection regime. All of this groundbreaking work, however, did not involve the use of liquid metals"

Jan 1, 2004

By S. S. Ryu, J. C. Kim, H. Lee, Y. D. Kim, I. H. Moon

"Recently, W-Cu alloy becomes one of the very important candidate materials for heat sink and packaging in the field of microelectronics due to its good thermal properties. The metal injection molding of W-Cu powder can satisfy the requirement for mass production of complex shaped parts in microelectronic devices. In the present study, the application of MIM process to the nanostructured W-Cu powder prepared by mechanical alloying was investigated. The multi-component binder system of 45PW+ l 5BW+ 30PE+ I OSA was proven to be suitable one for the MIM of the W-Cu composite powders by adopting the debinding cycles of multi-stage in N2 and H2 atmospheres. Other process conditions for the MIM of the nanostructured W-Cu composite powder were also studied. The MIM debinding part of W-30wt.%Cu was sintered to the relative density of more than 96% by sintering at 1200 °C for !hour in H2 atmosphere. Such an improvement of sinterability was attributed to the intrinsic homogenous and fine mixing state of W-Cu phases in nanostructured W-Cu composite powders, and also partly to the effect of the activated sintering by the presence of impurity introduced during the extensive milling.IntroductionW-Cu alloys have been widely used for heavy duty electrical contacts and arcing resistance electrode(1-2). Recently there has been a growing interest in this W-Cu alloy because of its superior thermal managing properties and its high micro wave absorption capacity(3). Such W-Cu alloy parts are conventionally fabricated either by the Cu infiltration sintering technique or by hot pressing of W-Cu powder mixtures. However, these conventional PM techniques are hardly applicable for mass production of small size parts with a complicated shape such as the parts required for microelectronic devices. The metal injection molding(MIM) technique is potentially applicable for the mass production of small and complicatedly shaped parts compared with other PIM forming techniques."

Jan 1, 1998

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993