Search Documents

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By John P. Hager

One possible approach for the recovery of mercury from acid plant blow-down sludge in smelters is the use of a vacuum retort reactor for the vaporization of the mercury with subsequent collection of metallic mercury in an attached condenser. An experimental study was undertaken to investigate the vaporization of mercury when present as a compound in the Hg-S-O and Hg-Se systems. A transpiration reactor was modified to operate under reduced pressure and with a continuous flow of inert sweep gas. A water-cooled cold finger was inserted into the exit end of the reactor to provide for the rapid quenching of the exit gases and the collection of the mercury. Rates of vaporization were measured at several temperatures for each compound and were generally found to be constant at a given temperature and reactor pressure. The results were used to determine the minimum operating temperature for 100% vaporization of the compound in 60 minutes. For Hg2SO4, HgSO4, and HgSO/2HgO the required temperatures. for a reactor pressure of 50 Torr. were determined to be 634°, 622°. and 603°C. respectively. For HgO, HgSe, and HgS the required temperatures were 557°. 451°. And 382°C. respectively. For HgS the rate of vaporization was also measured at a reactor pressure of 1 00 Torr. The rate of vaporization was found to be slower resulting in an increased vaporization temperature of 423°C. It was also determined that the mercury vapor present in the exit gas stream can back-react with the other gas species to a significant extent and can result in very little condensed metallic mercury. For the vaporization of both HgS and HgSe. the mercury vapor was found to have back-reacted to the extent that virtually none of the vaporized mercury was collected in metallic form. For the vaporization of Hg2S04? HgS04, and HgSO4*2HgO the amount of metallic mercury recovered varied from approximately 50% for HgS04*2HgO to approximately 10% for Hg2S04 and HgS04. Only for HgO was the recovered mercury in primarily elemental form. The application of the results to the operation of a vacuum retort and condenser system is discussed.

Jan 1, 2001

By Halvor Dalaker, Pål Tetlie

The decomposition of methane has been studied experimentally in contact with various oxides at elevated temperatures. For each oxide, the temperature at which the cracking starts has been determined. No correlation was found to exist between the temperature for the onset of cracking for a given oxide and the affinity for carbon of the oxide's metallic component. In terms of potential for using methane as a reducing agent, calculations are presented that indicate that the suitability of an oxide for such reduction depends on the desired methane+oxide reaction being more energetically favourable than the methane+methane=ethylene/acetylene reactions.

Jan 1, 2014

By Marcela Morvová, Mário Janda, Morva Imrich

"The possibilities of greenhouse gas mitigation using various methods are brought out. The special case of utilization of mixture of CO2 with other greenhouse gases in a synergetic way inside non-thermal plasma based system is described in detail.Measurements on pilot system comprising pyrolysis chamber as alternative energy system (production of hydrogen and liquid tar) were made for various biomass and waste as the input material. The exhaust from this system was treated with non-thermal plasma gap suitable for up to 650Nm3/hour of exhaust gas flow. Condensable portion of exhaust is liquefied in distillation unit; produced hydrogen is stored on-line inside nano sized carbon of our own production.The CO2 removal efficiency varies depending on exhaust composition between 45 to 98%. Other oxides as CO, NOx, SOx and several hydrocarbons and VOC are also removed. The main product connected with CO2 removal is a solid powder of proteinoid nature. There exist strong probability, that precursor of the origin of life on the Earth from primary atmosphere were formed in the similar way as it is present in the electric discharge system used. Our system is equipped with on-line as well as ex-post analysis of all forms of products. We have also developed a system for recuperation of all forms of produced heat. It is stored inside as latent heat of waxes.IntroductionNatural greenhouse effect on the Earth is caused mainly by water vapour with the average absolute concentration about 4%. Other gases able to absorb long-wave radiation and thus this causing greenhouse effect are CO2, CH4, N2O, halocarbons and as precursors ozone and NOX. Some of them we produce and introduce into atmosphere in large quantities during production of energy and in transport. This factor leads to permanent increase of average temperature of air, sea and oceans, so called global warming.Nowadays large amount of data exists showing that the temperature of Earth in the last 150 years has been continually increasing. It represents about 03°C per ten years and the most of climatologist believe, that the increased concentration of greenhouse gases in the atmosphere is responsible for this effect.The most important greenhouse gas is carbon dioxide CO2. Majority of CO2 emissions comes from electric power stations working with fossil fuels, cars and industry. Burning of fossil fuels contribute up to 80% to world wide anthropogenetic emissions of CO2."

Jan 1, 2010

By Klaus-Markus Peters, Robert M. Cravens, James G. Hemrick

"Degradation of refractories in molten aluminum applications leads to energy inefficiencies, both in terms of increased energy consumption during use as well as due to frequent and premature production shutdowns. Therefore, the ability to enhance and extend the performance of refractory systems will improve the energy efficiency through out the service life. TCON_ ceramic composite materials are being produced via a collaboration between Fireline TCON, Inc. and Rex Materials Group. These materials were found to be extremely resistant to erosion and corrosion by molten aluminum alloys during an evaluation funded by the U.S. Department of Energy and it was concluded that they positively impact the performance of refractory systems. These findings were subsequently verified by field tests. Data will be presented on how TCON shapes are used to significantly improve the thermal management of molten aluminum contact applications and extend the performance of such refractory systems.IntroductionThe production of molten aluminum creates aggressive environments for processing equipment, thereby requiring refractory materials to contain the aluminum during melting, transfer, treatment, and casting operations. Degradation of these refractories not only causes issues with reduced product quality and production yields, but also increases heat losses as the insulative properties of the refractories are compromised. Furthermore, in addition to disrupting production output, refractory failures lead to further impacts upon energy efficiency as large amounts of energy are lost during the cooling and subsequent reheating of the equipment as the refractory linings are repaired or replaced.The need for improved refractory materials is recognized throughout the industry. A joint U.S. Department of Energy and industrial workshop held in 2000 on applications for advanced ceramics in aluminum production [1] noted that refractory materials used in melt processing equipment have many limitations. The workshop report noted that these issues may be addressed by using advanced ceramics, but new materials must be cost effective when compared to current refractory materials. Also, in 2005 the Canadian aluminum industry produced a technology roadmap [2] having the goal of identifying and bridging gaps between current technological resources in the industry and future requirements. One of the areas identified as being crucial to the future of the industry was the need for improved molten aluminum-resistant materials."

Jan 1, 2009

By David E. Hardt

"One of the critical variables to be controlled during arc welding is the size or geometry of the weld pool. The measurement of pool geometry has become an increasingly important problem with the advance of welding automation and control, and this paper addresses that problem. The basic concept of pool size estimation via measurement of pool dynamics is presented. The theory underlying this concept is discussed and is followed by a review of the current work in this area. It is concluded that pool dynamics can be characterized by natural frequencies of oscillation, for stationary welds, and that these can be measured by appropriate signal processing performed on the arc voltage. However, it appears that only full penetration welds show a strong correlation between weld size and natural frequency. Also, the extension of these results to the realistic case of moving welds has yet to be considered in detail. Nonetheless, this method of in-process measurement for real-time weld process control is still quite attractive where applicable since it can be accomplished simply by modifying the arc current schedule and by signal processing of the arc voltage.INTRODUCTUIONThe study of welding process control has been dominated by research into methods of in processing sensing of the weld pool geometry. While it has been shown feasible to measure the topside pool geometry using video methods [1,2], the penetration or backside bead width have remained elusive quantities. This is particularly true if a topside sensor location is required.The concept of using weld pool motion as a pool geometry sensing method was proposed by Hardt et al. [3] and later demonstrated by Hardt and Zacksenhouse [5] and Richardson and Renwick [6]. The concept is based on the fluid dynamics of a pool constrained by a solid container and by significant surface tension forces (i.e. a small shallow pool, not a ""pond"" or ""lake""). Such a pool, if subjected to external forces, will exhibit a surface motion is a function of that force, the properties of the fluid, the surface tension, and the shape of the container. Thus, if this motion can be excited and measured, and the relationship to the pool geometry determined, a means of sensing pool shape will exist."

Jan 1, 1986

By G. H. Khoe

Although some hydrometallurgical process liquors contain significant amounts of ferrous and arsenate ions, no reliable thermochemical data for the aqueous complexes and the solubility of the ferrous arsenate precipitate are available. The complexation of iron(11) with arsenate has been investigated using the potentiomemc titration method. The results indicated that virtually no complexation of iron(@ with arsenate has been observed. This is in contrast to the significant complexing reported for iron(1n) with arsenate. The solubility product of the precipitate was calculated using the concentrations of appropriate arsenate species pertaining to the observed precipitation pH's. The fit of the observed precipitation points on the solubility curve of the computed stability diagram was used to assess the appropriateness of the equilibrium model.

Jan 1, 1991

By N. G. Azeredo

This work dealt with the evaluation of engineering structural clay brick samples that were sintered at estimated temperatures of 700 and 800°C. They were collected in a red-brick plant in Campos dos Goytacazes, RJ, Brazil. From a lot, a sample already sintered in its kiln at 700°C were collected and also a sample from the same lot only dried by the air, which were then sintered at 800°C controlled temperature. The samples were subjected to Brazilian Standard tests (ABNT NBR 15270:2005) to determine their geometric, physical and mechanical properties. In order to be classified as structural clay brick it is required minimum 3.0 MPa for the characteristic compressive strength (fbk) to be suitable for up to five floors structural building applications. We also used the Weibull Probability Plot and Weibull Maximum Likelihood Estimation to evaluate distribution parameters in order to compare the results of compressive strength obtained in the tests.

Jan 1, 2015

By C. Dresen

This paper discussed the reaction kinetics of the reduction of industrial phosphate pellets for P4 production. In the reduction process of various phosphate ores, the following parameters were investigated: Diffusion of the phosphorus oxide and other gaseous products from the reaction mixture after having been reduced on the reductant (coke) surface. Influence of silica on reaction kinetics. Temperature influence. Influence of mineralogy and morphology (different ores). Particle size influence of silica and coke. Experiments were carried out in a vertical tube furnace with 2 ores, 2 types of silica and one type of coke. Selected experimental conditions simulated furnace conditions. The following conclusions could be made: Reaction rate increases with the addition of SiO2 into the pellet. The reaction rate increases above 1350°C (melting temperature of the slag). Mixing different ore types in the pellets leads to differences in reduction kinetics. Particle size of the coke particles influence reduction kinetics. The amount of slag formation is influenced by silica addition, coke size and temperature.

Jan 1, 2002

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991

Direct electrowinning is an electrochemical process which has been developed for the extractive recovery of copper from dilute, acidic leach solutions. In passing through a thin particulate coke cathode. copper is reduced and electrodeposited in a thin layer forming a solid copper-coke sheet. The product is melted in a furnace to separate the coke, then the molten copper is fire refined to produce a salable product. A description is given of a prototype unit which is designed to treat 20 gpm leach liquor and recover over 100 pounds of copper per day. Economic analyses show that in a commercial facility producing about 25.000 TPY copper.*the direct electrowinning process has lower overall cost than either conventional iron-cementation or the newer liquid ion exchange-electrowinning when the leach liquors contain less than 2 grams per liter of copper.

Jan 1, 1976

By Hye-Sung Kim, Dong-Wha Kum, Gyeungho Kim

"Mechanical alloying is an effective way to finely distribute inert dispersoids in AI-TM (TM is a transition metal element) systems. It is considered that high melting point aluminides are formed by precipitation from the supersaturated aluminum matrix. The analysis is based on the fact that much higher content of TM than the solubility limit can be dissolved in alpha aluminum during the high energy ball milling. Nonetheless, the role of undissolved TM particles affecting the formation of aluminides is not suitably considered. In this paper, authors present experimental observation on the formation of Ab3Ti particles from mechanically alloyed AI-Ti alloys in the hyper-peritectic region. This study showed that, in the mechanically alloyed AI-20wt%Ti specimen, intermediate phase of cubic Ab3Ti and tetragonal AIz4Tis formed at 300 - 400°C and 400 - 500°C, respectively, before the MA-state reaches to the global equilibrium at higher temperatures. The formation behavior of Lh- Ab3Ti is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiating the formation of Ab3Ti phase during annealing.IntroductionInterest in the hyper-peritectic AI-Ti alloys is based on industrial demand for high-modulus and high-temperature aluminum alloys. Earlier works on hyper-peritectic AI-Ti alloys with 4 to 12wt%Ti show that these alloys are strong at ambient temperature and maintain high strength above 300°C when titanium-trialuminide (e.g., Ab3Ti) is finely distributed in the aluminum matrix [1,2]. High melting point and high stiffness with low density of AbTi make the AI-Ti alloys strong with greater thermal stability while keeping weight savings as much as possible. Titanium in aluminum shares other merits of transition metal additions because Ti solubility in Al is low (i.e., 1.l5wt%Ti at 665°C and virtually zero below 400°C), and fine dispersion of Ab3Ti particles is readily accomplished and resists grain coarsening effectively."

Jan 1, 1996

By B. C. Blakey

The economic feasibility of the sulphuric acid pressure leaching route for the extraction of nickel and cobalt values from limonitic ores is highly dependent upon the behavior of aqueous aluminium. This is primarily due to its precipitation as hydronium alunite ((H30)A13(S04)2(OH)6), which is one of the major scale-forming compounds found in autoclaves used for pressure leaching. As a result of renewed interest in the pressure leaching process, an investigation of the aqueous-solid eqilibria in the aluminium-sulphate-water system under acidic (< pH l), high temperature (230 to 270°C) conditions has been conducted. Pure hydronium alunite was synthesized in an autoclave by leaching boehmite (A100H) at elevated temperatures in sulphuric acid solutions initially 0.25 to 0.75 m H2S04 in concentration. Spontaneous, in situ precipitation of hydronium alunite followed. A high temperature solution speciation model was used for the analysis of the resulting solubility data in order to calculate equilibrium constants for the precipitation reaction.

Jan 1, 1994

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By G. R. Adams, N. Y. Tang, N. Qiang

"Aluminum is the most important alloy addition to Zn baths for controlling the reaction kinetics between the steel substrate and molten Zn in continuous galvanizing operations. Due to the complexity of the Zn-Fe-Al ternary system, the measurement and control of effective bath Al remains a challenge for modem galvanizers. The successful development of Al sensors has made the real-time measurements of bath Al contents possible. To facilitate their application, a computer interface and a palm-size data logger have been developed by Cominco. Plant applications indicated that the sensor possessed sufficient accuracy for process monitoring and control. The working mechanism of the Al sensors and Cominco's development work is described, and the results of sensor applications are presented.IntroductionControl of bath Al content is critical in modem continuous galvanizing because it has a strong influence on coating structure and properties and the overall product quality. The control of effective bath Al content (Al in liquid solution) is particularly critical for galvannealing where a high bath Al content may lead to incomplete alloying during post annealing, and a low bath Al content may result in other operation problems, such as excessive bottom dross accumulation and difficulties in coating thickness control. The desirable accuracy of the Al control is within ±50 ppm of target levels. In principle, such an accuracy is achievable for modem chemical analysis facilities, such as atomic absorption photospectrometer (AAS) and induction-coupled plasma (ICP). However, a recent study carried out by the International Lead and Zinc Research Organization (ILZRO) indicated that such an accuracy is rarely achieved in the zinc and steel industries.(1)"

Jan 1, 1997

By P. Meyers, F. DeSilva, L. Gottlieb

A number of tests looking at lead removal using ion exchange resins of various types from various aqueous streams have been undertaken. The tests focused on strong acid cation (SAC) and weak acid cation 0N AC) resins. It was found that the mechanism of lead removal is partly by lead filtration rather than solely by ion exchange in a large portion of the applications studied. This is not surprising since lead carbonate is essentially insoluble and almost all water supplies contain at least some carbonate alkalinity. Regeneration of lead from exhausted resins containing significant amounts of lead may not be practical in some cases because of the large chemical and waste volumes involved. Since lead, .·along with many other very insoluble metals, is often present as a suspended solid rather than in ionic form, ion exchange is probably not always the best technology for bulk lead removal.

Jan 1, 2000

By Leon E. Laforest

An early commitment by Kidd Creek Mines Ltd. (formerly Texasgulf Canada) to follow a stringent environmental control programme from the initial stages of design and development of its metallurgical facilities in Timmins, Ontario, has resulted in the on-going attainment of extremely low levels of industrial waste emissions. This paper outlines the monitoring programme initiated and maintained by the company&apos;s environmental control section. Comparative results of environmental sampling for the periods before and after the copper smelter start-up are highlighted.

Jan 1, 1983

By D. W. Ashman

The zinc pressure leaching plant at Cominco&apos;s Trail Operations is now in its ninth year of production. The plant produces a zinc sulphate and jarosite slurry which is further processed in the calcine leaching circuit. Elemental sulphur, a by-product of the process, is sold in the North American market. During the past eight years, a number of changes have been made to the plant to remove known production bottlenecks and to improve leaching extraction. These changes have raised production rates above the initial design so that the plant currently accounts for approximately 20 percent of Trail s zinc production. These rates are expected to be increased further upon the completion of the alterations currently in progress. The knowledge gained over the operating life of this plant has allowed Cominco to plan for a possible future expansion of the zinc pressure leaching plant. If expanded, zinc pressure leaching would account for approximately 48 percent of cominco?s zinc production.

Jan 1, 1990

By F. Leuzzi

Asbestos is a natural mineral fibre which has been known and utilized commercially for about a century. From the forties, it was employed on an ever-increasing scale throughout the mechanical engineering, building, paper-making and plastics sectors, to name but a few. There are essentially five minerals which provide fibres for industrial applications, namely, the chrysotile variety of serpentine and the amphiboles such as riebeckite, anthophyllite, cummingtonite-grunerite (amosite) and tremolite. About a fifth of the world&apos;s asbestos output was once taken by Europe for the manufacture of asbestos-cement products, reinforced plastics, paper and cardboard, panels, soft insulation and spray-on powders. However, in the sixties and seventies the hypothesis regarding the pathogenic nature of asbestos fibres started to gain ground. Moreover, between the sixties and eighties the EU issued a series of regulations designed to bring about a steady decrease in asbestos consumption. This line of action has culminated in recent years in a whole set of directives banning the use of asbestos in all products. This created a major problem, namely, how to clean-up the several million tons of various types of asbestos products in various states of conservation existing in Western Europe. CORDIAM (Pat. RM95 A 000269 and Pat. RM96 A 000782 in the name of ECOTEC S.r.1.) is one of the thermal inertization techniques recently proposed for this purpose. The process provides for the low-temperature ceramization of the toxic-harmful material. Of course, with such a great variety of waste materials and the volumes to be treated, as well as the need to ensure the correct dimensional design of the thermal sections of the treatment plant, it is necessary to know as much as possible about the thermal behaviour of the wastes concerned. This paper details the steps taken firstly to ascertain the thermal behaviour of such materials as may be encountered in day-to-day practice and secondly to examine the influence of the main process parameters on the preliminary design of gas- or fuel-oil-fired rotary kilns of the kind used for waste treatment.

Jan 1, 1999

By Jennifer Murphy, Brad S. Schake, Karol Holmes, John R. FitzPatrick, Mike H. West

"The separation and purification of uranium from either nitric acid or hydrochloric acid media can be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps.We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (1 DO-gram) flow experiments, using depleted uranium, were done after the small-scale evaluation of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos.Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process.Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail."

Jan 1, 1996