Search Documents

By S. Nagamatsu

Alumina supported gold catalyst prepared by spray reaction method (spr) provides gold particle with about 20 nm of diameter. The gold particle size is larger than conventional gold catalysts. However, the spr catalyst shows higher catalytic activity for NO-CO reaction. In the present paper, we have discussed the local structures of spr-Au/Al2O3 catalyst by using Au L3-edge XANES spectra. In order to investigate the local structures of Au-sites, multiple scattering approach to XANES analysis was applied. Calculated Au L3-edge XANES spectra for fcc-Au and Au2O3 were in good agreement with the observed spectra. XANES spectra for spr-Au/Al2O3 were characterized by 4 types of Au sites (bulk, interface, surface and peripheral). In this case, almost all gold sites (> 90 %) are bulk site. The other sites are less than 10 % of gold particle. However, the experimental and the calculated results of Au L3-edge XANES spectra for spr-Au/Al2O3 require about 30 % of gold oxide or hydroxide. Bulk of Al2O3 contains a certain number of gold nano-particles, which was incorporated in the bulk Al2O3 support. In the interface area, gold oxide forms a few layers. This result was also supported by DV-Xa electronic structure calculations. The comparison of the catalytic activities of the spray catalysts and the impregnation catalyst for the NO-CO reactions imply synergy effects between gold nano-particles and alumina support.

Oct 1, 2003

By Fernando de Oliveira Boechat

As maiores pressões e temperaturas atualmente empregadas a fim de aumentar a produtividade de fornos de DRI têm resultado em um subproduto indesejado: o aumento da geração de clusters. Estes clusters prejudicam o fluxo da carga e a permeabilidade do leito. A fim de limitar o tamanho destes aglomerados o forno MIDREX dispõe de três conjuntos de quebradores localizados em diferentes posições do forno após a redução da carga. A interação entre clusters e esses quebradores, entretanto, pode também prejudicar o fluxo da carga e aumentar a geração de finos. O trabalho utilizou o método dos elementos discretos (DEM) para avaliar as energias e forças resultantes da interação entre os clusters formados e os quebradores. A descrição dos clusters foi realizada usando o bonded-particle model, disponível no EDEM. Simulações mostraram que a presença de clusters altera as forças e velocidades no entorno dos quebradores que tenderiam a aumentar a geração de finos no reator.

Aug 16, 2017

By M. Yavuz

Underground mining method selection (UMMS) is one of the most important issues in mining engineering. Underground mining method should be primarily selected to make use of underground resources optimally. It is nearly impossible to change the mining method once selected by the reasons of rising costs and mining losses. Because of these reasons, UMMS process is extremely important in mine designs and economics. The strategy of underground mining method selection has been studied by different researchers in the literature. Boshkov and Wright (1973) proposed a classification system; Morrison (1976) suggested a selection chart; Laubscher (1981) proposed a selection methodology; Nicholas (1981) presented a classification system; Hartman (1987) developed a selection chart and Miller-Tait et al. (1995) modified the Nicholas? system and developed the UBC mining method selection process. In reality, UMMS is one of the important Multiple Attribute Decision Making (MADM) problems and mining engineers have always some difficulties in making the right decision in the multiple criteria environment. To make a right decision on UMMS, all known criteria related to the mining method selection should be analyzed and the problem solved according to suitable decision making techniques. A review of the literature reveals that decision making techniques have been used for UMMS applications. Kesimal and Bascetin (2002), Bitarafan and Ataei (2004), Bascetin et al. (2006), Alpay and Yavuz (2007), Karadogan et al. (2008) and Samimi Namin et al. (2008) used decision making techniques in UMMS applications. In this paper, two different MADM methods: Analytic Hierarchy Process (AHP) and Fuzzy Multiple Attribute Decision Making (FMADM) are applied to select the optimal underground mining method for a chromite mine and final solutions are then compared. THE AHP METHODOLOGY The AHP method developed by Saaty gives an opportunity to represent the interaction of multiple factors in complex unstructured situations (Triantaphyllou, 2000). The method is based on the pair-wise comparison of components with respect to attributes and alternatives. A pair-wise comparison matrix n×n is constructed, where n is the number of elements to be compared. The method is applied for the hierarchy problem structuring. The problem is divided in to three levels: problem statement, object identification to solve the problem and selection of evaluation criteria for each object. After the hierarchy structuring, the pair-wise comparison matrix is constructed for each level where a nominal discrete scale from 1 to 9 is used for the evaluation as shown in Table 1 (Saaty, 1980; Saaty, 2000). The next step is to find the relative priorities of criteria or alternatives implied by this comparison. The relative priorities are worked out using the theory of eigenvector. For example, if the pair comparison matrix is A, then, [Amax=××- [1] ] To calculate the eigenvalue ??max? and eigenvector w=(w1, w2,..., wn), weights can be estimated as relative priorities of criteria or alternatives. [ ] Since the comparison is based on the subjective evaluation, a consistency ratio is required to ensure the selection accuracy. The Consistency Index (CI) of the comparison matrix is computed as follows: [CImax--= [2] ] where ?max is maximal or principal eigenvalue, and n is the matrix size. The consistency Ratio (CR) is calculated as: [CR= [3 ] where ?RI? Random Consistency Index. Random consistency indices are given in Table 2. [ ] Table 2. The consistency indices of randomly generated reciprocal matrices As a general rule, a consistency ratio of ?0.10? or less is considered acceptable. In practice, however, consistency ratios exceeding ?0.10? occur frequently. THE FMADM METHODOLOGY The FMADM methods have been developed due to the lack of precision in assessing the relative importance of attributes and the

Jan 1, 2009

By A. F. Banks

"Potash processing has much in common in terms of unit operations and plant operating strategy with other mineral processing plants. As it is a rather large topic the processes will be broad brushed to give you some background and then I will go into a little detail on the things we do in the Cominco plant that may be of interest to the group as a whole. In particular the centrallized computer control system and associated instrumentation and the operator training programs will be covered as well as the mill fire, something that could happen in any plant. THE ORE AND PRODUCTSThere are differences in potash ores as you would expect. It is my intention to deal with the ores processed in the Saskatoon area. These are mined from the beds in the Patience Lake Member and have a mineralogical description as follows:Sylvite (Potassium Chloride) 40%Halite (Sodium Chloride) 55%Insolubles (Slimes) 5%A number of products are made from this ore. It is characteristic of a potash plant that you put as much effort into grading and converting the sylvite to meet market requirements as you do in recovering it."

Jan 1, 1976

Mr K.R. Beard was born on 19th December, 1958. He attended Marist Brothers College, Observatory, and Marist Brothers College, Linmeyer. He was awarded a bursary by SEIFSA (Steel and Engineering Industries Federation of South Africa) and gained the degree of B.Sc. Eng. metallurgy at the University of the Witwatersrand in 1982. He is a member of the Engineers' Society of South Africa. Mr G.A. Brown was born on 27th June, 1934, and matriculated at St John's College. He obtained the degrees of RSc. Eng. (Met.) at the University of the Witwatersrand in 1957, and M. Met. at Sheffield University in 1959. He is a member of the Institution of Mining and Metallurgy (UK) and the Society of Mining Engineers (USA). Or LA. Cramer was born in the USA and, having received a B.Sc. degree in metallurgical engineering from the Colorado School of Mines, he emigrated to South Africa in 1971. He enrolled as a graduate student at the University of Natal and successfully completed both an M.Sc. and a Ph.D. degree in chemical engineering.

Jan 1, 1989

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as fine aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs.

Jan 1, 1949

By Theodore Marvin

FOLLOWING the receipt of questionnaires from many parts of the world, the Aviation Committee is completing a review of the use of aviation in mining and petroleum operations. The summary of this study should be available at the 1937 Annual Meeting in New York City, at which time several papers will be presented on specific application of aerial geologizing. From the reports received, there is little question that this air branch of mining is here to stay. Of course, the transportation of personnel arid material continues to merit attention but it is in the division of aerial geologizing that flying is finding its widest, most technical application.

Jan 1, 1937

By Y. P. Chugh

Additional field evaluations of a modified continuous miner using a new spray system and modified scrubbers have been conducted by the authors. In this demonstration, a comprehensive package for dust control on a continuous miner which included previously developed modifications to the scrubber, scrubber intakes and the innovative chassis spray system was demonstrated. Side-by-side comparisons of the modified miner and regular miner indicated that the miner operator with the modified miner was exposed to 62% less respirable dust. Ram car operators with the modified miner had 38% less respirable dust exposure and the return air on the modified miner had 19% less respirable dust. The mining conditions during side-by-side testing were very comparable. These results support the findings of the modified spray system studies conducted earlier at different mines in Illinois on four occasions and the modified scrubber system field evaluation studies.

Jan 1, 2009

By G. van den Berg

Anglo Platinum has initiated a project to investigate hydraulic hoisting technology for platinum mines. Hydraulic hoisting systems are categorized as pumping, fluidizing feeder or displacement feeder systems. Positive displacement piston diaphragm pumps are most suitable for pumping systems but they require that the ore be milled prior to pumping. Fluidizing feeders are unsuitable for platinum ore applications due to the large percentage of fines in the ore. The three-chamber pipe displacement feeder has been most widely used for hydraulic hoisting and is the most suitable technology for platinum mines. Eight hydraulic hoisting applications covering pumping and displacement feeder technologies are reviewed. The key factors to be assessed in selecting a hydraulic hoisting system for a platinum mine are discussed. A typical platinum mine configuration will comprise an ore preparation plant (to produce -15mm material through screening or crushing), motive water pump on surface, high pressure water pipeline from surface to underground, ore slurrification plant, three-chamber displacement feeder, and a high pressure slurry pipeline to surface. The water and slurry pipelines are housed in a purpose drilled borehole. A hydraulic hoisting system selection chart is presented. A 150mm diameter system with a 25 MPa pressure rating is required to hoist 60 000 t/m from a depth of 1 200 m. Generic capital and operating costs are presented. A major potential advantage of hydraulic hoisting is that the fines, which contain a high percentage of PGMs, are captured underground and transported directly to the concentrator. Hydraulic hoisting technology is ideally suited to providing supplementary hoisting capacity to existing shafts that have reached the skip hoisting capacity limit. The main advantage for new shafts is the potential to significantly simplify underground rock handling and transportation. All hydraulic hoisting system components are proven. The only risk area is the wear rates of the valves and piping. Current estimates are based on gold ore. The business cases investigated show that the financial viability of the installations are not sensitive to wear rate. Hydraulic hoisting is technically feasible and financially attractive for platinum mines. Keywords: hydraulic hoisting, slurry

Jan 1, 2005

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By Steven Dapp

A new hyperbolic model for generating P-Y curves is developed for use in lateral analyses of cemented soils (a ?C-F? soil with both cohesive intercept and friction angle), and includes degradation of the static loading soil response to model the effects of load cycling (repeated loading) with load cycle number. The p-y curves, for both static and cyclic loading, were derived from full-scale lateral test results conducted on a set of six drilled shafts in a loess deposit at the Kansas DOT test site. Values of the model parameters obtained from the load testing at this site are presented, as well as a discussion of the model parameters effect on the results such that the model may be rationally applied to other sites with C-F type soils. A step-by-step procedure is presented to illustrate the application of the model. Correlation of the model to the CPT cone tip resistance (qc) from CPT testing is made, as this was found to be the most reliable; However, the model is applicable to other methods, both in-situ and laboratory, of assessing the soils strength.

Jan 1, 2011

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

By José L. M. Clemente, John R. Davie

"Abstract An extensive pre-production static and dynamic pile load testing program was conducted for a coal-fired power plant. The static load testing program included axial compression, uplift (tension), and lateral load tests. Three types of piles were tested: Monotube, closed-end pipe, and step-tapered. The load tests were used to (a) determine pile driveability characteristics for each pile, (b) verify pile load response behavior, and (c) provide data to support the selection of a cost-effective piled-foundation system for the plant. A recent publication (Clemente and Lewis, 2013) describes the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript describes site subsurface and groundwater conditions and installation of probe piles for testing, focuses on the uplift and lateral load testing program, and provides a comparative interpretation of the load test results.INTRODUCTIONThe pre-production probe pile load testing program described here was conducted for a 202-megawatt, coal-fired power and steam generating (cogeneration) facility. A schematic layout of the main plant (power block area) is shown in Figure 1, which also includes the locations of clusters of preproduction probe piles and boreholes drilled near these clusters.The load testing program included 24 pre-production probe piles driven throughout the power block area. The probe piles were driven at locations T-1 through T-8, shown in Figure 1. Three types of piles were driven at each location: Monotube pile; closed end, straight shaft pipe pile; and step-tapered pile. At each location, the three piles were driven in a row with the pipe pile at the center, and the center-tocenter spacing between piles was equal to about 1.5 m (> 3.5 pile diameters for the largest pile). No pile cap was used to connect the three piles, and the three piles driven at locations T-1 through T-8 will be referred to as pile clusters. A complete suite of static load testing (compression, tension, and lateral) was performed on each individual pile at Cluster T-2 and on the step-tapered piles only at Cluster T-8, shown in Figure 1.Clemente and Lewis (2013) provide details of the compression load testing program, the interpretation of instrumentation measurement results, and pile selection criteria. This manuscript focuses on the uplift (tension) and lateral load testing program. A brief summary of the site geology and existing subsurface and groundwater conditions in the vicinity of the test pile clusters is presented, with emphasis on T-2 and T-8. Probe pile driving results at T-2 and T-8 are also presented. Descriptions of the static uplift and lateral load test program at T-2 and T-8 are given along with a comparative evaluation of the load test results."

Jan 1, 2014

I am wearing two hats today. When the invitations went out to participate in this forum, two were received in the head office of the Department of Lands and Survey - one addressed to the Director-General of Lands and one to the Chairman of the National Parks Authority. It seemed logical that as the department is responsible to the Government for the administration of the National Parks Act 1952, we should respond by providing one speaker to cover both the department's interests and those of the National Parks Authority. I hope, however, that this will not blur the clear distinction which exists in the context of the mineral industry between Crown land on the one hand administered by the department for the statutory Land Settlement Board and national parks and allied reserves on the other hand which are the responsibility of the National Parks Authority.

Jan 1, 1976

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006

The validity of a steady state assumption made by Adams and Nicol (1986) in the modelling of the elution of gold from activated carbon was investigated. It is shown that the accuracy of the steady state approximation is dependent, not only on the magnitudes of the solution flow rate and reactor volume, but also on the lumped elution rate constant. Under the experimental conditions used by Adams and Nicol (1986) the steady state assumption was inaccurate. This could be circumvented in this instance by applying a rigorous general model which accounts for unsteady state behaviour in the solution and in the activated carbon to the experimental data.

Jan 1, 1997

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By Virgil Miller, R. G. Knickerbacken

"INTRODUCTION The Bureau of Mines work reported by the Metallurgical Division 4/ in 1934 shows the possibility of producing artificial manganese ore by pre- ferential oxidation of manganese from spiegeleisen produced from manganiferous iron ores of the Cuyuna range, Minnesota. A three-step process is described as being capable of producing a ferrograde ore from this type of low-grade, domestic, strategic material. However, the melting temperature in the last step of the process that forms the manganese product is high, and the phosphorus content is not easily controlled. Also, the tenor of the manganese in the product is not comparable with other methods that use less process energy.Lofquist 5/ patented an improvement of the above three-step smelting method, in which sulfide was added to lower the melting point of the product.More recently, reputedly successful attempts have been made to reduce iron preferentially from manganiferous iron ores, simultaneously removing the phosphorus with the iron, by means of an unusually high temperature blast and excess coke.Anson G. Betts 6/ patented a process for the matte-smelting of manganese ores, in which the ore was mixed with pyrite and enough carbon or coke to serve as thermal energy and reducing, agent in a manner similar to the standard blast-furnace process. This process was intended to give pig iron, a manganese-iron matte, and a waste slag. Wood, Barrett, and Porath 7/ presented data on the treatment of low-grade, domestic, manganiferous iron ores and low-grade, domestic manganese ores by this Betts mattes pelting process."

Aug 1, 1942

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

"The goal of the work was verification of bacterial leaching on the samples of black coal. From the results obtained it was clear that the coal is very well leached by Thiobacillus ferrooxidans and this technology can be used for coal desulphurization. A leaching time of one month is required, to remove 65% of total sulphur and 85% of pyritic sulphur.Microscopic evaluation of samples from Jaworzno showed, that it should be classed as a coal with low coalification, probably from black coal hemiphase. Macerals of the liptinite group were well distinguishable; they were of a dark brown colour. Evidence of coal mass oxidation was apparent on the fresh sample; in the test samples (during bacterial leaching) small grains were oxidised."

Jan 1, 2003