Search Documents

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

Market confidence is on the rise and industry leaders turning toward the vast and diverse region of Latin America are faced with abundant, yet daunting, opportunity. From the iron orebodies of Brazil to the renowned copper mines of northern Chile, drilling teams in Latin America are often faced with abrasive, broken ground. These types of ground conditions tear up coring bits rapidly, making it extremely difficult for even the most seasoned drilling teams to maintain effective productivity. The drilling challenges faced in this rich and opportune region are being met today by advanced coring technology, bringing with it the potential for increased productivity in Latin American mineral exploration.

Jan 3, 2010

By John B. Spencer

Earlier this year, Simplot Phosphates achieved a safety milestone at its Vernal, UT phosphate operations. In March, the entire operation reached achieved seven years without a lost time accident. And the mine operations at Vernal reached the 1 million hours benchmark without a lost time accident. This million hour achievement has been 19 years in the making. This achievement reflects the mine’s strong attitude towards safety, the company said. Safety is an integral part of its culture and requires diligence and considerable work. Attention to even the smallest of details cannot be allowed to slip. This is a record Simplot Phosphates said it hopes to improve on every day.

Jan 1, 2004

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

By T. Mwanza, B. N. Belford, P. Conradie

"Metix has introduced a three-piece ’deep-cooled’ copper slag tapblock into a six in-line copper matte settling electric furnace. The tapblock was designed without any internal refractory; it relies purely on the development and maintenance of a freeze lining on its hot face and within the tapping channel to protect the copper and promote the integrity of the surrounding endwall refractory lining. In addition, the geometry of the tapblock further supports the sidewall refractories, reduces the impact of funnelling and, therefore, the need for premature rebuilding of the furnace endwall, and facilitates easy removal and replacement of the wear components even under ’hot’ furnace conditions. Eighteen thermocouples embedded in the copper components ensure full resolution of the copper condition, enabling plant personnel to identify wear rates, estimate freeze lining thickness and stability, and schedule replacement of spares and wear components well in advance.At the time of writing the tapblock had been in operation for 6 months with approximately 350 000 t of slag having been tapped through it. Every indication is that the design will limit the need for premature relining of the furnace endwall due to rapid deterioration of the tapblock and its surrounding refractories. IntroductionNonferrous furnaces rely heavily on the maximization of refractory campaign life to increase profitability and reduce planned downtime. In large electric copper slag-cleaning furnaces utilizing insulating linings, campaign lives of six or more years are realistic if consideration is given to each aspect that can degrade the refractory lining during the campaign. An area that is particularly vulnerable is the slag tap-hole and the local surrounding refractory. To avoid premature relining of the furnace walls, every effort should be made to consider not only the tap-hole design itself, but also the selection of the sidewall refractory material and its construction immediately adjacent to the tap-hole, and furthermore the interplay between the tapblock and this adjacent refractory. A holistic approach to the design that considers these interdependent features in the slag tapping area can reduce the incidence of accelerated refractory wear (‘funnelling’), support the surrounding refractories to prevent their collapse, introduce easily replaceable wear components that can be exchanged with the furnace still ‘hot’, and encourage and maintain a stable freeze lining at the refractory hot face that maximizes the tapblock and refractory lifetime."

Jun 1, 2019

Satellite Image Based Strategies to Evaluate the Impact of Dismissed Mine Site - An Application to the Mae Moh Coal Mine Area in the Lampang Province, Thailand

Sep 13, 2010

By Robert Vergie

Like most of you, I would rather work on a job than talk about it. But it is fruitful to spend some time taking stock of important developments in the heavy construction field. One of the strongest recent movements affecting the industry has been the push for safety. I regret that it is a recent development. Not that builders were against safety. Too often though, it was easier to continue with dangerous old work methods than to try something new. Too often, it was easier for equipment manufacturers to build production tools with little consideration for worker safety. And too often, accidents and gruesome disasters occurred. The ultimate result of on-the-job injuries in construction and other industries was the Federal Government's Occupational Safety and Health Act of 1970. Individual states were required either to accept OSHA or pass updated regulations at least as stringent as the Federal requirements. These new rules must be strictly obeyed -- not just because they carry civil and criminal sanctions -- but because they correct unsafe conditions and reduce hazardous acts. Though some OSHA measures have been criticized as superfluous, most of them do in fact save lives and limbs. Equally important, the tunneler who follows the new safety regulations can be fairly certain of an efficient, uninterrupted operation. Regulations do sometimes bring rewards.

Jan 1, 1974

By D Chalmers, C R. Ward, B B. Beamish

Coal workers’ pneumoconiosis (CWP) has re-emerged as a major concern in the Australian coal mining industry. Harmful effects from coal dust inhalation have been well documented, but the underlying causes and mechanisms of CWP are still debatable. Research conducted in the USA has proposed a plausible link between the presence of pyrite in coal and the prevalence of CWP. Reactive pyrite in coal oxidises under ambient mine conditions to produce various iron sulfate minerals such as melanterite, rozenite, roemerite and szomolnokite. Rapid reaction rates are promoted by the form (size and morphology) of the reactive pyrite present, which provides both increased surface area and increased porosity for easy air access to reaction sites. The products formed from reactive pyrite oxidation are often needle-like crystals with thicknesses in the order of 1–2 µm (eg melanterite and rozenite) and prismatic crystals with thicknesses less than 5 µm (eg roemerite) have been recorded. The densities of these minerals are significantly less than quartz, which makes them prone to becoming airborne with the normal coal dust. In fact, the mix of these mineral salts is commonly referred to as ‘fairy dust’ by mine workers due to the way they can become entrained and sparkle in the mine ventilation air, particularly if they occur in the upper part of a seam that is forming a coal roof. Examples are presented of the various products of reactive pyrite oxidation found in three Australian coal samples, which provide evidence of the physical and chemical mechanisms that would support the USA findings, particularly in terms of a source of bioavailable iron leading to increased inflammatory stress response.CITATION:Beamish, B B, Ward, C R and Chalmers, D, 2017. Products of reactive pyrite oxidation in the mine environment – implications for coal workers’ pneumoconiosis, in Proceedings Australian Mine Vent Conference 2017, pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By David Kress

Mill crushing drive systems are essential to cement producers. With the increased emphasis on operating efficiency, it is vital that these systems be dependable and reliable. No one needs the costs or headaches associated with unscheduled downtime or inefficient machinery operation. A reliable drive system starts with the proper selection of the ring, or girth, gear and continues through proper maintenance. Ideally, selecting the right girth gear brings together the gear manufacturer, the system designer and the end user. The gear manufacturer must know the details of the application, the demands that will be placed on the gear and the nature of the equipment to be driven. Similarly, the user and the system designer must be familiar with the variables that affect gear drive performance and service. For example, an application that places a torque load on the drive in excess of its rated capacity will result in gear tooth distress and, in severe cases, breakage.

Jan 1, 2000

The Wamum and Idzan Creeks Prospect, located 79km W of Lae, Morobe Province, Papua New Guinea (PNG) was discovered by the exploration arm of Conzinc Riotinto of Australia Pty Ltd (CRAE). The detailed surface exploration and 11 vertical holes drilled by CRAE, combined with the recent work by Highlands Gold Limited, indicate the occurrence of porphyry copper-gold mineral- isation and associated alteration. The prospect occurs within andesitic volcanics of the Middle Miocene Langimar Beds. It is bounded by NE trending faults to the NW and SE. The alteration and mineral- isation is hosted in the andesitic tuffs adjacent to high level quartz diorite and hornblende diorite stocks. A NW trend to alteration and mineralisation is obvious in Wamum and Idzan Creeks. The main alteration type is propylitic with minor zones of potassic alteration. A late sericite-quartz-kaolinite-pyrite alteration overprinted the earlier alteration and mineralisation. Copper and gold mineralisation is related to a quartz-carbonate-chalcopyr-ite-pyrite (¦ bornite) vein stockwork and biotite ¦ K-feldspar alteration. The mineralisation system at Wamum and Idzan creeks is low in total sulphides. It is considered as a high- level fracture-controlled system with limited low grade Cu-Au mineralisation.

Jan 1, 1991

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By E Selvapandian, R Barr

Arrium (previously OneSteel) initiated a desktop study into the performance of its hematite ore beneficiation plant in early 2010. The beneficiation plant utilises jig concentrators and spirals to upgrade low-grade hematite recovered during mining at the Iron Duke (ID) mine site located 60 km south-west of Whyalla. The study, conducted in conjunction with Mineral Technologies, identified a number of opportunities for improvement, which were validated by a series of sampling campaigns and a pilot plant trial. One of the major recommendations was to upgrade the ultra-fines processing circuit from a single-stage spiral circuit to a three-stage circuit. The upgrade of the ultra-fines circuit was estimated to provide a significant increase in fines production and grade.In order to capitalise on the strong iron price at the time of the project, Arrium decided to utilise a fast-tracked approach to design, construct and commission the processing equipment required to achieve the improvements identified. This decision introduced the risk of missing critical steps in the project development process, which could have potentially resulted in major issues in latter stages of the project. In addition to the challenges introduced due to the expedited time line for project completion, this project presented unique challenges due to its brownfield nature. One such challenge faced was the integration of the new equipment and control system software.Furthermore, the importance of the ID ore beneficiation plant (OBP) contribution to the companyÆs export commitments meant the upgrade work had to occur while minimising disruption to normal operation. This decision presented a set of new challenges to an already complex project. One such challenge was the need to build and commission the new spiral circuit in isolation from the operating plant.The aim of this paper will be to highlight some of the challenges faced in a complex brownfield project such as the ID OBP upgrade and discuss how they were managed to enable the successful commissioning of the process in early 2012.CITATION:Selvapandian E and Barr, R, 2013. Managing challenges faced in the brownfield commissioning of an ultra-fine hematite processing circuit at ArriumÆs Iron Duke ore beneficiation plant, in Proceedings Iron Ore 2013 , pp 533-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By H. Lowers, P. Hageman, S. Diehl, D. Fey

Understanding relationships between mineralogy, texture, microstructural features, and element distribution and residence in minerals, is critical for accurate modeling of mineral weathering in waste-rock piles. The morphology of minerals and deformation structures, such as veins and faults, are important factors that control: (1) fluid access to the mineral surface to initiate dissolution, (2) the distribution of trace elements, and (3) formation of secondary minerals. We characterized the mineralogy, textures, and chemical properties of waste-rock material at three sites at scales ranging from outcrop to micrometer scale. A comprehensive hand-sample to thin-section scale methodology utilizing light microscopy, scanning electron microscopy, electron microprobe, and laser ablation ICP-MS was used to thoroughly characterize the waste-rock material.

Jan 1, 2007

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By L. R. Herrmann

The research described in this report is the first phase of a comprehensive program for the development of a characterization for the structural properties of rock masses. The mathematical expression of the characterization is especial' tailored for use in conjunction with modern structural analysis procedures. The objective of the first phase of the project is to determine the feasibility of representing the structural properties of rock masses in terms of the analysis of an appropriate "representative volume" the results of this investigation are described in detail in the body of the report. The current state-of-the-art concerning the understanding and description of the fundamental mechanisms of rock behavior are determined from a survey of existing literature. The development of a representative volume that captures the most important of these mechanisms is described, In order not to unduly obscure the fundamental aspects of this development, the mathematical analysis of the representative volume is limited to plane strain conditions. A subroutine for the numerical evaluation of the proposed model (i.e., the analysis of the representative volume) is presented. The steps necessary for the incorporation of the subroutine directly into existing two-dimensional finite element structural analysis programs are described. Comparisons between the predictions of the proposed characterization and published results of simple laboratory tests are presented and discussed. Finally recommendations are given concerning suggested improvements of the model and the extension of it to the general three-dimensional case.

Jan 1, 1974

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By Özgür Bezgin

This paper presents observations on the installation of drilled shafts from two construction projects and an academic study with experimental and analytical parts. The construction projects involved the use of pressurized drilling methods. The experimental part of the academic study involved the use of the auger drilling method. The analytical part of the academic study investigated the effect of drilling methods on the soil-structure interaction and the behavior of drilled shafts under lateral loads. The concept of ?free-length? is introduced for the lateral load design of pressure-drilled shafts that are thought to be fully embedded within a soil media. The academic part of the study presented herein was conducted in Rutgers, the State University of New Jersey.

Jan 1, 2009

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008