Search Documents

THE art of mine surveying has made very great progress in recent years, and is still advancing, perhaps faster than any other branch of surveying. The scope of the mine surveyor's duties has greatly increased, his instruments and methods have improved, the responsibility of his position is greater, and the end is not yet in sight.It might be supposed that such a steadily growing subject would have an adequate literature, but this is by no means the case and outsiders commonly judge mine surveyors by their text-books. Hardly any condemnation can be too strong for most of these books. The English books truckle to the antiquated and crude methods apparently still in use in England, and thereby largely aid in perpetuating them; they commonly in illustrative examples give the distances in fathoms, feet, and inches; they spend page after page discoursing on instruments that should have been forgotten long ago; they try to antagonize theory and practice by detailing such calculations as that a certain vein will contain 2,003.907 pounds of galena per square fathom, and then reduce this amazing quantity to hundredweights, quarters, and pounds. Nothing can be more unscientific, or, for that matter, less businesslike, than unwarranted assumptions of accuracy; it is, perhaps, the greatest curse of applied science. Here we have a calculation to thethousandth part of a pound, when there is probably an unavoidable error of two hundred pounds. What shall we say of a man who explains how to measure the depths of shafts to the hundredth part of an inch by means of short brass rods screwed together...

Jan 1, 1909

By S. H. Badenhorst

Zacharias Lewala discovered a diamond at Grasplatz, near Lüderitz in April 1908. While this stone may not have been the first diamond to be found in this barren, inhospitable area, it most certainly was the stone that set off a chain reaction ultimately leading to the creation of Namdeb as we know it today. [ ]

Jan 1, 2003

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

By Ian Hooper, Alan Winter, Stefan Sadokierski, Craig Covil

The existing Tappan Zee Bridge was built in the late 1950s and has been working over its design traffic load for some time now. A new project, which is being jointly sponsored by the New York State Thruway Authority and Metro-North Rail Road, is looking at new alternatives to provide new road and rail crossings of the Hudson River. These include 2 to 5 mile and potentially longer tunnel crossing options that include hardrock TBM and EPBM opportunities. The paper describes the project needs and tunnel concept design work done on some of the alternatives. It also relates to the current EIS process for the project and talks about a possible double-stacked tunnel option. It also talks about the geology and environmental constraints relating to tunneling and provides and introduction to the tunnel ventilation work necessary for tunnel crossing of this magnitude. It does not report on the bridge engineering options being evaluated.

Jan 1, 2005

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

In an earlier paper (Stanton, 1953) a brief account was given of the geological environment and structure of the Lloyd Copper Mine orebody, Burraga, N.S.W. The present paper is concerned with the chemical and mineralogical features of the ore from this mine.Investigation has been made difficult because of inaccessibility of the workings, which have been fallen in for many years. The exact positions within the orebody of the specimens described in this paper are known in only a few cases. The specimens examined are from the collections of the Mining and Australian Museums, Sydney, and from material collected by the writer from the upper parts of the mine and from various dumps about the old workings.However, no significant variations in the nature (as distinct from grade) of the ore have been mentioned in the old reports, or by Carne (1908) or Kenny (1928), so it is likely that the specimens examined are reasonably representative of the orebody as a whole.CHEMICAL CONSTITUTIONThe ore is of simple and apparently very uniform composition.It is essentially a copper ore, with minor amounts of zinc and very minor amounts of lead. Plotting of copper against zinc shows a more or less sympathetic relationship between these at least as far as 20 per cent. copper - the highest grade assayed during the present investigation. The trend of the plots indicates a Cu/Zn ratio of about 15/1 to this point. Lead is very low and extremely sporadic, showing no clear relationships with the other metals.MINERAL COMPOSITIONThe principal non-opaque minerals are quartz and sericite, and these are accompanied by smaller quantities of muscovite, calcite and biotite. Quartz is the most abundant mineral, occurring both as a C'onstituent of the country rock a quartz-sericite schist-and as veins. All quartz aggre...

Jan 1, 1955

By W Herrmann, R R. Large

Volcanic-hosted massive sulfide (VHMS) deposits in ancient, submarine volcanic belts of Australia include mound, lens and sheet-style Zn-rich polymetallic deposits, massive and disseminated pyritic Cu-Au deposits and disseminated, stratabound Au-only deposits. Variation in morphologies, metal ratios, volcanic environments and alteration features indicates there exists a spectrum of deposits from the classic VHMS model, to hybrids between VHMS-porphyry Cu and VHMS-epithermal end members. Zn-rich, polymetallic deposits form eitheron, or just below, the seafloor, whereas the Cu-Au and Au-only deposits form sub-seafloor by replacement of specific volcanic lithologies. Alteration zoned outwards from quartz -> chlorite -> sericite ¦ carbonate is typical of VHMS deposits across the spectrum. Quartz and carbonate alteration is dominant in the Au-only systems,chlorite alteration is commonly developed close to Cu-rich ores, and sericite and carbonate alteration zones are well developed in the stratiform Zn-rich ores. The most useful geochemical vectors for Zn-rich ores are the alteration index [AI=100(MgO + K2O)/(MgO + K2O + CaO + Na2O)], the chlorite-carbonate-pyrite index [CCPI=100(MgO + FeO)/(MgO + FeO + K2O + Na2O)], Mn content of carbonate, Mg/(Mg+Fe) ratio of chlorite,whole-rock Tl, Sb and Ba/Sr ratio, S34S of pyrite, and whole-rock S18O. The most useful vectors for pyritic Cu-Au ores are AI, CCPI, S/Na2O ratio, Na content of white mica, and Fe content of carbonate.

Jan 1, 2002

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By Jeremy P. Doolan, Leigh B. Neindorf, Geoff W. Capes

The development and use of rock mass classification tools have been a key component for improving stope design over the past 4 years at the Xstrata Zinc George Fisher Mine in northern Queensland, Australia. In 2003, stope extraction data from 3 years of open-stope mining provided an excellent situation to review the assumptions in the feasibility study. Extracted stope profile information, drillhole geotechnical data, underground observations, and oral and written communication were used to develop a thorough stope reconciliation performance database. With-out collecting the back analysis data and presenting the data in a usable format, engineers are left to debate opinion instead of engineered judgment. This can lead to biased and uninformed design parameter choices with the potential to repeat poor design. This paper demonstrates some effective, practical examples of empirical data collection where rock mass classifications tools were developed and used to create improved confidence in predicting stope stability and failure profiles. The work contributed to design changes that resulted in a reduction in stope hangingwall dilution and an increase in head grade while continuing to ramp up production from 2003–2005.

Jan 5, 2007

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

Amongst the unavoidable studies of the mining engineer who desires to reach the maximum efficiency, is the subject of patents. With the fundamental principles of the patent laws of this and other leading countries he should of course befamiliar, but still more should he keep abreast of that practical knowledge which will enable him to act or advise wisely when the patenting of a new invention, or the sale, purchasing, or adoption of a new patented machine or process becomes amatter for consideration. As every engineer worthy of the name is an inventor and more particularly every mining engineer he has a direct interest in watching the progress of legislation and administration concerning patent monopolies.His worldly prospects may indeed, to a considerable extent, depend upon the defeat of bad patent laws and the removal of incompetent officials, or the appointment of better ones. Better patent administration is always in Australia a valid requirement, and until engineers generally take up and press the demand, bad administration is likely to continue. Even though every engineer is not a patentee, nevertheless his interests in patents must always be direct and powerful, and ignorance or apathy in regard thereto must inevitably injure either his own interests or those of his employer. When we consider the tens of thousands of mines scattered through Australia alone, on everyone of which there is expensivepatented machinery, and when we consider the thousands of...

Jan 1, 1901

By Tom Cooney

A small number of mining contractors worldwide have evolved their businesses to be able to provide a ?total service solution? to their clients. Thiess, an Australian-based international mining service provider, works with numerous clients to tailor delivery methods and commercial arrangements to suit individual projects. The benefits of Thiess? extensive experience is brought to each client and project, whilst business improvement within projects, to the mutual benefit of both the client and Thiess, is a key part of all long term contract relationships. Historically, optimal business outcomes were closely related to the achievement of production and cost performance measures. Whilst these remain fundamental to successful mining businesses, other elements of sustainability are assuming increasing importance. As a large energy user, greenhouse and energy management is becoming an important part of Thiess? business. Thiess is a signatory to Australian government initiatives such as Greenhouse Challenge Plus, and is integrating energy management into its operations and business improvement programs, in many cases to the benefit also of the client. This paper will highlight the benefits that an organisation such as Thiess can bring to a mine owner. Thiess? approach to business improvement and cost reduction, sustainability and energy management, as well as the relationship between these will also be considered. Increasingly, overall mining performance is dependent on the alignment of formally disparate elements.

May 1, 2007