Search Documents

By W. P. Tassie

"The location of Quintette Coal Limited's pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette's operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette's success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By M. Seeger

The demographics and the growing numbers of people provide a strong signal that the demand for electrical power in Southern Africa will grow considerably over the foreseeable future. Without a steady and increasing supply of electricity development of the continent is likely to be constrained. The inventory of solar, wind, hydrothermal, geothermal and biomass resources will probably provide sources of energy for the future The parallels between extraction of natural resources in the minerals industry and the green energy industry is striking, and the well-established project development process in the minerals industry provides an ideal and useful template for comparing the establishment and development of green energy projects. The potential levels of power generation and carbon savings are described.

Jan 1, 2010

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001

By W. P. Diamond, F. Garcia, J. K. Marshall

Many longwall mines rely on methane drainage to supplement traditional fan-based ventilation systems. However, the surface production facilities for methane drainage systems, including gob gas ventholes, are commonly located in remote locations, sometimes without convenient access to electrical power, and they may be monitored infrequently. The first evidence that a methane drainage system may not be operating efficiently, or not operating at all, can be an increase in methane concentrations at a return air shaft or underground where the workforce is exposed to the risk of a methane explosion. A solar powered, remote gob gas venthole monitoring and cellular telephone-based real-time data transmission system has been developed and successfully field tested by the National Institute for Occupational Safety and Health (NIOSH) to address this problem. With this system, individual methane drainage boreholes can be monitored from the mine office to determine current operational performance parameters, as well as review past data to anticipate maintenance needs and troubleshoot operational problems.

By B. K. Shibler

During a research program to develop improved methods for recovering elemental sulfur and useful sulfur compounds from secondary source materials, the technical literature was searched for pertinent articles on processing methods. This report summarizes results of the literature survey and describes the more important processes that have been used or suggested for recovering sulfur and sulfur compounds from all non-Frasch sources. The bibliography presented represents a survey of the available English language literature on the subject through 1958, with particular attention focused on the period 1950 through 1958. Engineering Index and Industrial Arts Index were the principal guides used in the survey of this period. Chemical Abstracts was used to a limited extent to identify a few key foreign articles and patents. The Sulfur Symposium (4)4 published in November 1950 by Industrial and Engineering Chemistry includes a broadly representative selection of the literature up to 1949. Therefore, this reference was used extensively to locate and list pertinent articles on processing methods reported in the period prior to 1950.

Jan 1, 1962

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By Paul J. Axtell

This case history describes the foundation design and construction for the New Mississippi River Bridge, presently under construction in St. Louis, Missouri. The 1,500 ft (457.2 m) main span of the cable-stayed bridge is supported by two delta tower pylons in the river, with anchor piers on each bank. The final foundation design was completed as a part of an Alternate Technical Concept (ATC) proposal by the winning construction team, and utilized drilled shafts up to 11.5-ft (3.5-m) diameter that were socketed into very hard limestone. As part of the ATC foundation design, a full-scale, bi-directional static load test was performed to verify the design and allow use of higher resistance values. This paper presents the results of the site exploration, construction of the load test shaft, details of the load testing, and a comparison of the test results with various design parameters.

Jan 1, 2011

Although not fully accepted in South Africa, the Theory of Sampling originally proposed by Pierre Gy is fast becoming the cornerstone of sampling practice throughout the world. The growing acceptance of Gy?s Theory of Sampling in South Africa can be attributed to a number of factors, chief amongst them being the development of a tradable mineral asset market, the promulgation of the Mineral and Petroleum Resources Development Act (MPRDA), the growing number of commercial and academic courses that are offered on sampling, and the regulation of the industry through internationally acceptable guidelines and rules for reporting and trading in mineral assets. The size of the South African minerals industry and the dependence of our economy on mineral production have also meant that correct sampling is of key importance to mineral trade. ISO standards have been the principal guides for producers of mineral bulk commodities who produce to customers? specifications, whereas Gy?s insights have been most readily accepted by precious and base metals producers whose product is sold into metal markets. Understanding of small-scale variability is essential in the precious and base-metal industries, but detailed studies of the effects of heterogeneity have not been as productive in the bulk commodities. Sampling practices at different stages of mineral development from exploration, face sampling and grade control, ore processing and handling, metallurgical sub-sampling, point of sale sampling, and sampling in the laboratory are considered in the gold, platinum, ferrous metal, and coal industries. A summary of the impact of poor sampling in these industries is presented. Generally it appears that poor sampling practice is most likely to erode mineral asset value at the early stages of mineral development. The benefits of good sampling are considered, especially with regard to the financial implications of bias and error on large and consistent consignments of bulk commodities. Keywords theory of sampling, sampling errors, ISO standards.

Jan 1, 2014

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

By Steven D. Wirch

Abandoned underground coal mine areas must either be sealed or ventilated to comply with federal mine regulations. Ventilation of these abandoned areas is often impractical due to roof falls and inadequate primary mine ventilation. If the area is sealed, a very complex ventilation system is set up. In which the gob "breathes" in and out due to barometric pressure fluctuations. The Gob Assistant is a computer program (for use on IBM compatible personal computers) which allows the prediction of air flows into and out of a sealed mine area. Gas flows with applicable control techniques are also modeled. This information is presented to the user who will decide which control technique, or combination of techniques will ultimately be applied. The Gob Assistant is an intelligent gob simulator that can reduce the guesswork involved in predicting the effects of sealing and control techniques before they are applied. This paper provides the fundamental principles upon which the Gob Assistant is based, verification of these principles, and an explanation of how these principles were integrated into the Gob Assistant.

Jan 1, 1988

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

Jan 1, 1925

The concentration of Mt. Morgan sulphide ore has always been attended by serious loss of gold. Until recently, with a simple selective flotation flowsheet, even the lowest grade of ore milled-about 2 dwt. per long ton-thislloss was 0·9 dwt., whilst for average to high-grade ore, 3·5 to 5 dwt., the figure was 1·5 to 2·0 dwt. Early in 1937 it was decided to equip the research laboratory for an investigation into the condition and location of the escaping gold and the physical and mineralogical barriers preventing its recovery.With the completion of: this equipment in July 1937, trial and error testing, which had been explored to exhaustion, was abandoned and a five months' research programme mapped out and commenced. Based on the knowledge so gained, a flowsheet combining primary desliming, bulk flotation of the natural slime, selective flotation of the deslimed fraction, and cyanidation of the selective flotation tailing was drafted and tried with encouraging results in a 70-lb. per hour pilot plant. This flowsheet, modified to meet current circumstances, is being dove-tailed into the existing 1,500-ton sulphide ore concentrator, though the cyanidation treatment is actually carried out in the oxidized ore mill, to which the flotation tails are pumped.RESEARCH EQUIPMENT(1) Five tube elutriator (Fig. 1) t built in the company's workshop.

Jan 1, 1939

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

The Reefton Goldfield on the West Coast of the South Island of New Zealand was a significant gold producing area between 1860 and 1951. During this period it produced approximately 2.1 million ounces (67 tonnes) of gold. The largest single producer on the goldfield and the deepest mine in New Zealand, was the Blackwater Mine at Waiuta which produced 21 tonnes of gold. The Prolubition Shaft reached a depth of 878 metres (317 metres below sea level). The mine closed suddenly in 1951 with about 66 000 tonnes of are remaining in the stapes. Since closure there has been no attempt to determine the ore potential of the mine at depth. This paper summarises the geology, history and resource potential of the mine and sets out two options for evaluating the remaining resource. The options are either deep drilling from surface or recovery of the Prohibition Shaft and underground development and drilling. A schedule for each option is presented and discussed.

Jan 1, 1992

By J. O. Osterberg

The realities of foundation enginering are that the work never proceeds exactly as expected. The various reasons, exploration, design, construction, and legal are discussed. Case histories are presented with an analysis of why the projects did not turn out as expected and how the difficulties might have been avoided.

Jan 1, 2010

By Kathryn L. Neale, Derek L. Mulligan, Robin E. Goad, Norman A. Duke, A. Hamid Mumin, W. John Camier

"Abstract - The NICO and Sue-Dianne deposits are being explored and delineated by Fortune Minerals Limited in the Mazenod Lake District of the Northwest Territories, using an Olympic Dam model. The deposits were discovered in the south part of the Great Bear magmatic zone (GBMZ) within the Proterozoic, Bear Structural Province of the Canadian Shield. They are the only known significant Canadian examples of Proterozoic iron oxide-hosted polymetallic deposits. Worldwide, this class includes such deposits as Olympic Dam and Ernest Henry in Australia, Kiruna-Aitik in Sweden, and Salobo in Brazil. Their considerable size, up to 2 billion tonnes, and polymetallic ore assemblages make them highly attractive targets for exploration. Common characteristics of this class include their Early to Middle Proterozoic cratonic settings with extensional rifting evolving from collisional tectonics. Deposits typically occur along major structural lineaments within the aureoles of a distinctive suite of anorogenic potassium-rich "A-type" granite intrusions. Although hosted by diverse lithologies, deposits of this class are characterized by a number of other diagnostic regional- and deposit-scale features, which may be recognized in reconnaissance- and propertyscale geological and geophysical surveys.The southern GBMZ in Canada has several characteristics (age, tectonic setting, geology and geophysical attributes) similar to those of the Olympic Dam deposit and its other significant global analogues. Airborne and ground geophysical surveys carried out in the GBMZ identified coincident potassium, uranium, magnetic, resistivity, chargeability, and gravity anomalies centered over the NICO deposit. The nearby Sue-Dianne deposit is characterized by coincident uranium, potassium, magnetic, resistivity and chargeability anomalies. Both deposits occur within a regional, northweststriking, arcuate trend of volcanic and sedimentary rocks characterized by significant positive Bouguer-gravity and magnetic responses and are believed to represent a major basement discontinuity. The NICO anomalies are at the intersection of this regional trend with a major transverse fault through Lou Lake. Regional and local geophysical data indicate the presence of significant concentrations of iron oxide within a broad area of intense potassium metasomatism. Geological mapping identified cobalt, gold, bismuth, and copper mineralization in biotite-magnetite-amphibole-sulfiderich ironstone and schist. This mineralization is localized within altered wackes of the Snare Group, which are unconformably overlain by potassium feldspar- (±hematite ±magnetite) altered rhyolite of the Faber Group. The Sue-Dianne deposit is a hematite-magnetite-Fe-silicate-cemented diatreme complex enriched in copper, silver, gold, and uranium within a broad zone of potassium, iron, quartz, and epidote metasomatism. The diatreme is located at the intersection of two major faults at the north end of the basement discontinuity and is hosted in rhyodacite ignimbrite marginal to the Faber Lake rapakivi-granite pluton. At both deposits, diatreme- and maar-facies iron oxide-cemented breccia straddle the regional metasedimentary-volcanic unconformity, suggesting that mineralization formed in a near-surface environment synchronous with the onset of volcanism."

Jan 1, 2000

Terramin Australia LimitedÆs Angas Lead and Zinc Mine operates in the unique and picturesque environment of Adelaide Hills, 60 km South East of the Adelaide city centre itself. The mine was granted approval for construction by the South Australian Government in April 2007 and the Process Plant was constructed and commissioned in July 2008. This paper outlines the background to the plant design and the approval process given the close proximity to the local town of Strathalbyn, with a major focus on the commissioning learnings from the Concentrator startup for future reference and a review of the operational performance of the Concentrator throughout the first year of successful production versus design and expectations.

Jan 1, 2009

By R. J. Boyd

SUMMARY The productivity of drill and blast methods of mining in hard rock is limited by the cyclic nature of the operation, and a plateau of performance has been reached, even with the most advanced equipment developments. Higher mine operating costs and lower metal prices have more than ever generated the need for breaking through these productivity barriers. After initial field testing The Robbins Company has designed and manufactured, on a joint venture basis with Mount Isa Mines, Ltd., Australia, a prototype "Mobile Miner" for continuous cutting of hard rock. This paper describes the cutting concept, the initial application of a completed 1,156 m (3792 ft.) long 14% decline, actual performance and delay analysis, developmental modifications, anticipated performances of a fully developed machine, and possible future applications. Sincere appreciation is expressed to the management of Mount Isa Mines, Ltd., for allowing access to the data used in this paper. The views expressed here are those of the author and not necessarily those of Mount Isa Mines, Ltd. INTRODUCTION A paper titled, "Design and Development of a Mobile Mining Machine", was presented by J.P. Kindsvater at the RETC, New York, in 1985. This paper described the evaluation of a test fixture in an andesite quarry near Seattle, followed by design, construction and

Jan 1, 1987