Search Documents

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By E. A. Metz

Perfect combustion in an engine would produce only water vapor, carbon dioxide and nitrogen as by-products; however, complete combustion is never achieved. As a mobile power plant, the diesel engine is relatively inefficient in terms of energy produced from the energy potential of the fuel. The diesel is not a perfect engine. The fuel burned can undergo a very large number of reactions in the combustion chamber. It only stands to reason that a large number of compounds are contained in the exhaust, actually, thousands of chemicals. The exhaust can be broadly divided into a gaseous phase and a particulate phase. Each phase is made up of organic and inorganic compounds. The vapor phase contains carbon monoxide, sulfur dioxide, various oxides of nitrogen and many hydrocarbons. The particulate phase contains clusters of respirable inorganic particles made mostly of carbon. This paper will address the health hazards, as we know them today, of the major components of the particulate phase in the exhaust of diesel engines. It will briefly examine the operational factors of the diesel engine as it applies to particulate emissions. Longitudinal studies of occupationally exposed miners are needed with documentation of levels of exposure before a chronic effect of exposure can be determined. At this time, it is not possible to conclude from human studies the level of diesel exhaust exposure that results in the observed lung cancer risk.

Jan 1, 2001

By P. E. J. Pitfield, S. D. G. Campbell

The regional structure of shear and deformation zones in the belt, which is recognisable in plan view on Landsat TM images, is interpreted in terms of a conjugate-shear model. Gold mineralisation is related to this framework at a variety of scales. The principal recurrent structural geometries hosting deposits at mines such as Motapa, Durban, Charliesona, Cecil, Sunace, Turk group, Queens district, How, Peter Pat, Matabele Sheba, Goodenough, Old Nic and Bushtick are associated with shear zones and folds and include conjugate systems (shears, shear intersections, kink sets), side-step systems (en echelon segmentation, duplexes, monoclinal inflections, antiform-synform couplets) and interactions of the two. Linear sections of shear zones are generally poorly mineralised. The same geometries are identifiable on all scales from local to regional, so sections of regional structural lineaments or areas within mines should be prioritised for further investigation or development on the basis of the gold-bearing geometries observed to be dominant locally

Apr 1, 1996

By Dean Lindsay, Inna Dymov, Mariam Melashvili, Jim Smolik, Chris Fleming

"This paper presents results from the proposed cyanide detoxification circuit for Seabridge Gold’s KSM project. The proposed flowsheet uses a two-stage CCD (counter-current washing/decantation) circuit to transfer the flotation products CIL(carbon-in-leach) barren solution to a SART process (Sulphidization, Acidification, Recycling of precipitate, and Thickening of precipitate) to recover copper and free cyanide from the copper cyanide complex. The SART barren solution is then treated by an AVR process (Acidification, Volatilization of HCN gas, and Reneutralization) to concentrate the cyanide that was liberated in SART for recycling to leach. The washed CIL barren pulp (the CCD underflow) is treated with the SO2 /Air process to oxidize residual cyanide.The goal of this complex flowsheet is to recover and recycle as much cyanide as possible and produce a final effluent containing less than 0.5 mg/L copper and CNWAD at the lowest cost. The SO2/air process is capable of achieving low residual CNWAD (<1 mg/L) in the final product, but the persistence of aqueous copper above the target level has been detected in the treated solution in some instances. The expected high concentrations of copper and cyanide in the KSM CIL barren ( >200 mg/L each species) and the difficulties this might create for the SO2 /air process was a key factor in the decision to consider including the washing, SART and AVR steps in the project flowsheet.The target concentrations of CNWAD and Cu were readily achieved after aging the SO2 /air treated pulp, as would occur in a tailing or polishing pond. This suggests no additional treatment will be required to sustain low levels of these species in the final plant effluent."

Jan 1, 2015

Fine coal is defined as material with a maximum size of 1/2 in. Various methods for separate washing of such coal are discussed briefly because separate treatment can lead to a higher overall recovery of coal or to a product having a lower ash content.A felspar jig is discussed in detail because it is the method most recently adopted in Australia, and because it has the advantages of compactness, flexibility and automatic Gontrol, with minimum operator attention. This jig has a variety of adjustable controls to enable the desired results to be obtained from a wide range of coals and the general application of each control is discussed.The only separate treatment of fine coal in the Illawarra district is by felspar jigs on Bulli seam coal.INTRODUCTIONAll reasonably large Australian collieries now win coal by mechanical methods. but while mechanization leads to more economic production of high tonnages, it also changes the characteristics of the coal won. In particular there is an increased proportion of fines, and an increased ash and moisture content. However, specifications of coal for sale have become more stringent, and consumers now require coals in a definite size range with a lower and more uniform ash content, as well as with a low and uniform moisturecontent.These factors have led to the need to wash and grade run-of-mine coal at the pithead. In&apos; plants where the whole of the run-of-mine coal is treated in a jig, some of the fine coal in the feed is beneficiated; the extent depending on factors such as the type of coal and the feed rate. However, for dense medium treatment, fine coal must first be screened out, and there may then be no washing of fine coal at all.

Jan 1, 1961

During recent years there has been a marked increase in the use of explosives in Queensland coal mines. Delay detonators have been introduced and their use has extended with the wider application of mechanised methods of mining.The need for careful study of the characteristics of delay detonators is stressed so that the advantages of simultaneous firing, from the points of view of safety and efficiency, may be obtained. With their use new potential hazards are introduced. These hazardsare considered and means whereby the overall safety may be improved are discussed.The increase in the number of misfires since the introduction of delay detonators is shown and the examination of misfired detonators is described. Lessons to be learned! from these misfires are noted and details are given of the essential requirements for safe and efficient blasting using delay detonators.INTRonUCTIONOne of the aims of mechanization in coal mines is to reduce the physical effort applied to the winning of coal. Explosives play an important part in achieving this and, following the introduction of power borers for the drilling of shot-holes in Queensland coal mines, much of the arduous work associated with coal getting has been eased. During recent years there has been a marked increase in the consumption of explosives, as shown in Table 1, and it must be the aim of all to use these explosives safely and efficiently. That there are dangers associated with the use Of explosives cannot be denied. The shotfiring operation is fully covered by legislation and, being under the control of one man, shQuld be capable of being carried out with a high degree of safety. The main source of accident appears to be the failure to take proper cover and this has resulted in...

Jan 1, 1958

By M. Veiga

"Mining is an energy and water intensive activity. Increasing energy efficiency and reducing water consumption are two of the key requirements in moving toward a more sustainable mining industry. Water reduction, reuse and recycle options are reviewed, identifying cases where these options have been implemented. Then a novel mine water network design method is described, which analyzes a mine/mill water system in order to identify areas where water requirements and water system energy requirements can be reduced. First, a site water balance is determined and major water consumers and sources are specified. Next, multiple possible combinations of supplying water to mine and mill consumers are compared. Finally, low energy and water combinations are identified.INTRODUCTIONMining consumes vast quantities of energy: The whole mining and metals sector consumes over 12% of the world’s energy (DOE, 2009). Mining also requires large quantities of water, although mining water consumption is a relatively small portion of the overall world water use. Even in relatively dry, mining-intensive countries like Australia and South Africa, mine water consumption is only 2-3% of national water demand (Brown, 2003). However, at the local level, when mining takes place in areas where water is scarce, mine water consumption can severely impact local supplies. In addition, acid rock drainage, leaks from waste impoundments, or direct disposal of tailing into waterways can contaminate surface and groundwater (MMSD, 2002). Mine water systems can be large energy consumers, but better mine water systems can reduce both water and energy consumption. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry.This paper addresses conventional base-metal or precious-metal mine sites, which consist of an underground or open pit mine and a mineral processing plant, or mill. Ore is extracted and processed through the plant to produce a saleable product. Tailing, or waste material, is then deposited in a tailing storage facility (TSF). Any rock removed from the mine with no economic value, or waste rock, is stored without being processed."

Jan 1, 2010

By A. v. E. Conradie, I. Nieuwoudt

Comminution and flotation circuits are frequently perturbed by disturbances, such as feed particle size variations, ore hardness and varying mineral liberation, which can have a significant impact on the recoveries and grades. Although advanced control strategies can neutralize many of these disturbances, few such systems have been implemented at present. One reason is that it is only recently that the requisite sensor systems have been developed and used to control froth flotation systems. Another is owed to the complexity of these non-linear interactive systems. In this paper, a plant-wide control strategy is considered, wherein both unit operations have a single overall control objective. The automated design of the controller is based on an advanced evolutionary algorithm viz., Symbiotic, Memetic Neuro-Evolution (SMNE), for developing neural network controllers in a reinforcement learning framework. A rigorous phenomenological comminution and flotation model was used to develop suitable neurocontrollers, which used all possible sensor inputs and available manipulated variables. The neurocontroller managed to identify optimal or near-optimal operating conditions consistently and showed robust performance in the presence of significant disturbances. The results suggest that evolutionary reinforcement learning offers a very competitive approach towards the development of integrated non-linear controllers for mineral processing plants. Keywords: neural networks, control, flotation, comminution, evolutionary reinforcement learning

Jan 1, 2003

By H. F. Letient, D. C. Johnson

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid rock drainage (ARD) and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid-generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid-generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings toward the end of the mine life, thereby generating a non-potentially acid-generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-potentially acid-generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid-generating rock and to be flooded at the end of mine life.

Jan 1, 2004

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

By James V. Errico

On October 1, 1993 the regulations for assessing and cleaning up contaminated soil and groundwater in the Commonwealth of Massachusetts were revised. These new regulations, known as the Massachusetts Contingency Plan (MCP) 310 CMR 40.0000, were developed to keep routine releases out of the regulatory system and rely on private parties to handle most releases without Department of Environmental Protection (DEP) oversight. An integral part of the new MCP is the Licensed Site Professional (LSP). An LSP is required to handle activities and render opinions once a site enters the MCP. These regulations must be adhered to where ever a release has occurred, including construction sites. A brief overview of the new MCP is given below; see attached MCP Flowchart for graphical summary. Entering the MCP Process A release of oil or hazardous material (OHM) to the soil or groundwater above applicable reportable quantities (RQ&apos;s) or reportable concentrations (RC&apos;s) will require notification to the DEP and compliance with applicable provisions of the MCP. RQ&apos;s and RC&apos;s are listed in the MCP (310 CMR 40.1600) for most compounds that are typically encountered. For each compound there are two RC&apos;s for soil (S-1 and S-2) and two for groundwater (GW-1 and GW-2). The S-1 and GW-1 RC&apos;s apply to sites that are environmentally more sensitive, as a result they are lower than the S-2 and GW-2 RC&apos;s.

Jan 1, 1994

By B. Swarbrick

Today’s mining occurs in a dynamic world of conflicting objectives. Mining companies have to look further than a traditional cash flow analysis to determine the potential value of developing a mine. In particular, proposals for new mine developments undergo rigorous scrutiny by a variety of stakeholders including regulators, NGO’s, and the local communities. From a business risk perspective, how mining companies address stakeholder concerns can have a dramatic impact on the success of the project. In today’s mining environment mining companies must continue to ‘walk the talk’ to stay in business, particularly during downturns in the business cycle. Falconbridge’s Raglan Mine is an example of a project that was successfully developed in a region that is sensitive from many perspectives, including environmental, socio economic, and regulatory. Close working relationships with local stakeholders along with strong environmental management systems are necessary elements of continued success for the project.

Jan 1, 2000

By H. F. Moore

DURING the last six years, there have been many extensive investigations of the fatigue of metals. The major work of &apos;these investigations has been the determination of constants for fatigue strength of wrought ferrous metals; but during the past year or two there have become available considerable test data on the fatigue strength of certain nonrferrous metals, including copper, brass, bronze, nickel, copper-nickel alloys, aluminum and aluminum alloys, magnesium and magnesium alloys. It is not proposed to give here extensive quantitative tables of test results; for such tables, reference is made to the published data of various laboratories. The following general conclusions, however, seem to be fairly well established: 1. The phenomenon known as "fatigue" of metal really a progressive fracture of metals. A minute (probably submicroscopic) crack is formed in the metal, the internat stress, is intensified at the ends&apos; of the crack, and under successive applications of load the crack spreads like a minute hacksaw cut until there is not enough sound metal left in the cross-section of the piece to stand the load. applied, and then failure occurs suddenly. 2. For wrought ferrous metals, there is .a limiting intensity of stress (as computed by the ordinary formulas of mechanics of materials) below which, a metal is able to withstand an indefinitely large number of repetitions of stress without failure. This limiting stress is known as the "endurance limit or the fatigue limit.? For reversed flexure, the endurance limit for. wrought ferrous metals is usually not far from 50 per cent. of the ultimate tensile strength.

Jan 1, 1925

By H. P. Kritzinger, T. C. Kingsle

"Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications, including ferrovanadium, nickel carbonate, nickel laterite, iron ore reduction, and spodumene (lithium) production.This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates."

Jan 1, 2015

By Gregory A. Johnson

Operations and Maintenance departments have long had an adversarial relationship. The widespread evolution and adoption of modern management techniques such as Reliability Centered Maintenance (RCM) and Lean Production however has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance, and are now adopting Lean throughout the organization. Modern management initiatives like these explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in the realms of people and methodology. One area that has lagged behind in supporting these developments however is information systems. Enterprise Asset Management (EAM) systems in maintenance and newer Manufacturing Execution Systems (MES) in operations have not been truly integrated in the way needed. Complicated plants, different software architectures, continually changing conditions and many variables have lead to systems problems which have contributed to the maintenance/operations divide. Master data synchronization (the ?plant tree?) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology including web services and service orientated architectures. New technologies are coming on-stream to enable the final ?bridging of the gap?.

Feb 1, 2008

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By S. C. Gouws

"SynopsisSustainable infrastructure development has long been identified as a key enabler for socio-economic growth and poverty reduction in societies globally. Twenty-one years into the young South African democracy, economic prospects are fragile and unemployment statistics are high. According to Trading Economics (2015) the GDP growth rate in South Africa averaged 3.07% from 1993 until 2015.Through the National Development Plan 2030, the government has responded by instituting the Presidential Infrastructure Coordinating Commission (PICC) to direct national growth and drive job creation by effecting a long-term infrastructure investment programme. The Commission is mandated by Cabinet to coordinate, integrate, and accelerate implementation of more than 150 individual social and economic infrastructure plans.In the civil infrastructure development sector, increased urbanization is compelling governments and the public sector to expand safe and reliable public amenities, but the availability of real estate for construction in congested cities is a challenge. Within the mining infrastructure construction industry safe, rapid, and efficient mine extraction strategies are imperative to realize increased production, business hurdle rates, and stakeholder expectations.Asset owners and stakeholders are obliged to consider advanced mechanized underground excavation and support technologies in order to present feasible solutions timeously. From an engineering design, procurement, and construction management (EPCM) perspective tunnelling technology and boring applications have a distinct advantage over conventional excavation techniques. These solutions may enhance commerce and transportation by expanding infrastructure in concentrations of national economic activity, providing crucial linkages with rural areas, between cities, and across international borders.This paper explores the contribution by mechanized tunnelling technology and boring applications applied in conjunction with digital and automation technologies compared with conventional methodologies. The technological expertise, combined with a paradigm shift in delivery of project objectives, will promote economic growth, aid recovery from the economic downturn, and improve social development."

Jan 1, 2015

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002