Search Documents

By Mark I. Copeland

This study was conducted by the Bureau of Mines to determine the effect of steel reheating practices in burning natural gas on the amount of silicon required to prevent the formation of copper on steels containing up to 1 wt-pct Cu. Formation of copper, which causes surface hot shortness, was readily prevented by as little as 0.3 wt-pct Si and by 2 vol-pct excess oxygen in the furnace atmosphere when reheating steels containing up to 0.8 wt-pct Cu. Up to 0.8 wt-pct Si content and careful control of reheating conditions were necessary for steels containing 1 wt-pct Cu. Best conditions for these steels were reheating to 2,200° F (1,205° C) in burning gases containing 2 vol-pct excess oxygen, and then to higher temperatures in gases of 6 vol-pct excess oxygen. Slag and mold wash were not detrimental on steels reheated for 8 hr by a soaking-pit-type furnace schedule, but they were problematical on steels heated for 2 hr by a pusher-type furnace schedule. The effect of silicon contents on scaling rates also was determined.

Jan 1, 1974

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

The Role of Mineral Processing in the Development of Cement with Low Carbon Emissions

Sep 13, 2010

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By Kash Sirinanda

¿Cómo dirigir nuestra agenda hacia la creación de una organización minera sostenible? En el presente texto se examina la compleja estructura de las empresas mineras, y se abordan los cambios en cuanto a la creación de valor minero, tanto como las tendencias futuras en la industria. Tomando en consideración la sostenibilidad propuesta por las Naciones Unidas para los modelos de negocio en minería, el autor explora las áreas en las que debería centrarse el liderazgo minero del futuro.

Oct 30, 2020

By Maurice J. Peterson

The applications of optical spectrochemical methods of analysis for determining trace impurities in metals are described, and the need for developing analytical procedures capable of accurately determining fractional parts per million of impurity elements in metals is stressed. Factors which determine sensitivity of detection and means to extend sensitivity levels in spectrochemical methods are discussed. Examples from the current literature illustrate the diversity of spectrochemical techniques that have been applied to the analyses of varied sample types, Many of the methods use preconcentration procedures to increase sensitivity limits. A bibliography containing abstracts of recent methods in included. Optical spectrochemical analysis is based upon the measurement of radiant energy emitted by atoms of the elements to be determined when a sample is subjected to a suitable source of excitation. The behavior of the valence electrons during excitation, usually by an arc, spark, or flame, produces radiant energy of specific wavelengths. This is recorded as spectral line images on a photographic film or plate by the spectrograph; for direct-reading instruments, the spectral lines are detected with photomultiplier tubes. The spectral lines result from the excitation of atoms in the sample. Each variety of atom produces its own characteristic set of lines, thus serving to identify the elements in the sample. Increased concentrations of elements in the excited sample results in increased blackening of the spectral line images.

Jan 1, 1961

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920' s and 1930's, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a 'collector' in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy, H. S. Ray

The Ni oxide was reduced with a CO-CO2-N2 gas mixture and the effects were observed of process variables such as roasting temperature, time and CO partial pressure. Extraction of over 90% of Ni was achieved by ammoniacal leaching of ore that had been reduced for 1 h at 760 degrees C under a gas mixture with a volumetric CO/(CO+CO2) ratio of 0.57. The kinetic data were found to conform to the Ginstling-Brounstein equation. The applicability of this model was confirmed by evaluating the apparent activation energy with the use of independently constructed differential and integral plots, which showed an excellent match

Dec 1, 1995

Common brattice cloths in use in Australian coal mines are compared by permeability measurements. The respective advantages of twill weave and tarpauling* weave cloths are listed, and the improvements to be obtained in the ventilation of a mine by using tarpauling cloths instead of the commonly used twill cloths are stressed. Plastic cloths are widely used overseas and are briefly discussed.INTRODUCTIONThe onset of extensive full-scale mechanization in Australian coal mines during the past few years has increased attention given to the ventilation of working places. Many inadequacies of the present system have been brought to light and not the least of these is connected with the use of brattice cloth, both in directing the flow of air around the face and in acting as a temporary sealing mechanism. A well-constructed line of brattice will only provide fair ventilation for a distance of 100 ft. Beyond this point the volume or air reaching the face falls off rapidly.Some of the shortcomings associated' with the use of brattice cloths are:1. Hurried installation, necessitated by a rapid advance, often results in poor workmanship with, consequently, an excessively high leakage rate.2. High places caused by falls of roof are difficult and time-consuming to seal.3. Curtains, in lines of brattice crossing transport routes, are difficult to maintain.4. Lines of brattice interfere with rock-dusting and clean-up of fine coal.5. Repair and maintenance of brattice consumes much...

Jan 1, 1959

By Benedicto Hadad Cintra

In an inflationary environment the need for reduced cost is a daily concern of all industries. The Du Pont do Brasil "Expanded Pattern" method has proven to be an extremely effective means of reducing costs in mining, quarrying and construction operations. Over the past years much emphasis was placed on rectangular drilling patterns where the burdens are less than the spacing. The Expanded Pattern method combining rectangular and staggered patterns, was implemented in 1971 in Brazil after extensive trials in close collaboration with numerous explosives users and Du Pont do Brasil Technical Services Engineers. The best multiple row spacing-to-burden ratio (S/B) was demonstrated to be in the 2 to 5 range and the effective spacing to burden ratio (Se/Be) was found to vary from 5 to 11. These ratios are for the interior of the blast pattern and do not hold true along the front row of holes. Geological rock properties, hole diameter and inclination, explosives energy and loading density, explosives characteristics, blast pattern geometry, bench height and delay patterns along with type and size of digging, hauling and crushing equipment must all be evaluated for each and every operation. The integration of these interrelated parameters, together with sound blasting practices are the basis for the Expanded Pattern method. Color slides and documented case histories will be presented.

Jan 1, 1985

By Guangyi Sun

Wall rock classification method for coal mine support is the main factor affecting mine support. It is greatly affected by the combined effect of randomness, fuzziness and human being's incomplete knowledge. There are several coal rock classification methods. Using different rock classification methods the same engineering rock mass can be classified into different classification leading to different construction practices.

Jan 1, 2005

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

Updraft sintering of lead concentrates was introduced at Port Pirie in 1955 and since that time a considerable amount of investigational work has been carried out in the laboratory and on the plant with the objective of improving both the understanding of the process and its practical application.From this work it is now possible to predict trends in design and operation, which should result in capital savings and increased efficiency of future updraught plants.INTRODUCTIONOver the last 70 years a remarkable advance has been made in the method of preparing lead concentrates for smelting in the Port Pide blast furnaces of The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.). Beginning in 1889 with heap roasting, the process progressed to Ropp roasters and Huntington-Heberlein pots in various combinations, then to multiple small Dwight Lloyd (D.L.) downdraught machines. In 1940 two large 10 ft by 50 ft D.L. downdraught machines were installed, and finally in 1955 updraught sintering was ,introduced with the installation of the present 10 ft by 99 ft sinter machine.At the time this last machine was built it was the first unit of its type and thus, of necessity, an experimental machine. During the eight years it has been operating a considerable amount of investigational work on sintering has been carried out both on the plant and in the laboratory.It is now felt that sufficient information is on hand to predict at least tentatively, some of the future developments in lead sintering, whereby both the quality of the sinter and the rate of production may be improved. This will result in a considerable reduction in smelting costs.

Jan 1, 1964

By G. A. Brown

Major mining projects are developed with the assistance of lending institutions who provide hundreds of millions of dollars in funding over several years, and of course expect those funds to be returned with interest. Two Australian banks have adopted the Equator Principles, an emerging financial industry benchmark for assessing and managing environmental and social risk in project financing. Project financiers have encountered environmental and social issues that are both complex and challenging, particularly with respect to projects in the emerging markets of Asia-Pacific and elsewhere. There are many recent and historical examples of failures by resource companies to effectively manage their environmental, social, safety and security risks, some of which have caused the project to fail completely, and some of which have caused the temporary cessation of production. These events put the financial institutions' funds at risk through inadequate management capacity and non-compliance adversely affecting the ability of the borrowers to repay the loans. They can also reflect adversely on the reputation of the lending institutions. In assessing these risks, lenders are increasingly looking at the track record of the borrower in its country of origin and in other countries where it operates. Lenders are wary of companies that have one standard for operations in a developed country, where the regulatory environment may tightly control what they do, and another standard for operations in countries where the regulatory regime is perhaps less stringent. Lenders may require environmental and social reviews or audits to be conducted on their behalf by competent third parties prior to a loan being approved, and annually over the life of the relationship. The mining industry's concept of the unwritten `social licence to operate' is highly relevant in relation to the delivery of community benefits that are sustainable post-mine closure. This paper provides examples of recent practices that support financial viability and sustainable development, as well as examples of some failures that have put lenders at risk.

Jan 1, 2007