Search Documents

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By Turner WG, Short RR

Obviously, the paramount advantages of contract mining have been recognised by mine developers throughout Australia, as evidenced by surface gold mining operations of significant output almost exclusively being performed under contract. These paramount advantages of using an experienced professionally managed contractor result from the mine developer being freed from financing the required relatively large capital expenditure at current relatively high interest rates or in a capital scarce stock market, and from the need to recruit and sustain a large operating work force in a competitive labour market.

Jan 1, 1990

By A. E. Taylor, A. S. Judge, P. T. Lafleche

"Resource development in northern Canada has special requirements which derive from the unique environmental and eco-logical nature of the northern environment. In this paper several case histories in which the Permafrost Research Section of the Geological Survey of Canada (GSC) has participated are used to illustrate how geophysical methods may be used to address some of these considerations. Although some of these examples were developed while examining problems directly related to oil and gas development and transport in frontier regions, such or similar methods also have application to mining problems.IntroductionA critical parameter is the distribution and thickness of permafrost, which in northern Canada varies from being a few metres and discontinuous at the southern limit to thicknesses in excess of 700 m in the Arctic Islands'!'. Figure I is a schematic diagram of typical ground thermal conditions in a permafrost zone. The upper zone is defined by an active layer which undergoes a seasonal freeze/thaw cycle. In the simplest case, the ground remains permanently frozen below the active layer to the depth of the O°C isotherm, which is defined as the base of the permafrost. Water chemistry, pore structure and pore or grain size may cause the base of the frozen ground to be above the permafrost by up to 100 m(2). Ice can be found within the permafrost in the pores of solid rock or sediments, as massive ice within unconsolidated sediments or as ice lenses within fissures in a solid rock mass. The mining technique used in these conditions, whether open pit or underground, can differ considerably from that used in southern Canada. In the high Arctic, for instance, the dry drift method is feasible underground in the permanently frozen host rock. The frozen nature of the wall rocks can obviate water-related problems."

Jan 1, 1987

By H. K. Taylor

Ore reserves are inadequately defined. Geological reconnaissance and pre-feasibility mining work generate a broad range of valid tonnage estimates, many published for the benefit of various interests, who may view all figures as reserves. This work reviews the regular estimation of tonnages, grades and relevant factors for single deposits. A consistent framework of definition is suggested which, by conforming to the known structures of feasibility studies and long-range plans, avoids the pitfalls of over-categorisation and of unrealistic promises. Applications are based on North American experience but are intended for general use

Sep 1, 1991

By Phil N

A large number of experiments have been carried out by many workers on the recrystallization of deformed and subsequently annealed metals and alloys. Although observations on single crystals are of great importance in the study of the recrystallization textures of deformed and annealed metals, very little of this work deals with material in this form.Since, in deformed metals, the stress concentration is greatest at the grain boundaries and along the planes of slipping, it is to be expected that recrystallization will start in these regions. For example, in polycrystalline aluminium (1),:1: (2), copper (3), a-iron (4) and brass (5), (6), which had been deformed by cold-rolling, drawing, pressing or stretching and then annealed, the new grains first appeared in the boundaries of the original crystals, whilst in the case of cupronickel (7) and iron (8), recrystallization commenced along the slip planes of the deformed material. Deformed and annealed single crystals of aluminium (9) and cadmium (10) first start to recrystallize along slip planes and in deformation twins.The present work deals with the process of recrystallization of single crystals of lead after deformatjon by creep.Two factors enter into these experiments that were not met with in other work on this subject. Firstly, lead...

Jan 1, 1940

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009

By T. A. Lang

Concepts and equations have been developed to quantitatively determine the stability of a rock bolted coal mine roof as a structural (beam-arch) member consisting of reinforced rock units. The equations take into account: rock bolt tension, length, spacing, and orientation; size of opening, strength and physical properties of the rock; and loads from distressed rock, and were critically reviewed using sensitivity analyses and the results available from relevant previous analytical and physical model investigations. It is concluded that they can essentially be validated by using small scale physical models and the full size mine entry model at the USBM Spokane Research Center. However, a comprehensive research program, including analytical and laboratory investigations and field trials in typical mines, will be required to define and validate criteria and standards for using the equations as a basis for a rational design code for rock reinforcement installations to replace the semi-empirical rules now being used. For example, these studies have shown that the practice of installing vertical roof bolts with a uniform spacing equal to the bolt length is inherently unsafe and that the spacing should be reduced near the walls to prevent shear failure of the roof strata. The development of such a rational design code would provide enhanced safety in coal mining operations and warrants a high priority in the Bureau's ground control research program.

Jan 1, 1981

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Edward G. Cunney

[Track in underground bituminous coal mines was investigated and technology has taken from other industries in order to Main information on conditions that impair the safety and efficiency of the track and to develop guidelines ad useful information on the constriction, inspec¬tion and maintenance of mine track. Volume l contains information oil the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features such as gage, descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques; inspection requirements and methods; and methods for managing and performing track maintenance work. As a research product, it 0005 nut repeat the summary or derivations. Volume 5, Inspection Handbook, summarizes recommended standards and procedures from Volume 2 and provides related information for read: refer¬ence by inspectors in tin mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.]

Jan 1, 1977

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By José Luis Calderón, Percy Arrosquipa

Compañía Minera Poderosa ha identificado una interesante oportunidad de generar valor y de mejorar tanto el clima laboral como el de relaciones comunitarias mediante el proyecto descrito en este artículo. El proyecto se orientó a motivar la incorporación de prácticas de responsabilidad social, tanto entre proveedores de bienes y servicios, como entre empresarios mineros artesanales en proceso de formalización. Como ejemplo, se analiza el caso del cofinanciamiento de la obra “Mejoramiento del sistema de agua para consumo humano del anexo Pueblo Nuevo”, que benefició a 195 familias con un servicio de agua de calidad las 24 horas del día. De este modo, se corrigió una fuente de conflictos sociales y se materializó una alianza para el desarrollo local entre la mediana minería y la minería artesanal. Por su parte, Asociación Pataz entregó certificados de donación, deducibles del Impuesto a la Renta, a los aportantes.

Sep 30, 2017

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By Grant D. Nicholas

This paper compares an integrated evaluation approach to decision-making with more traditional sensitivity analysis and Monte Carlo simulation. The primary objective is to highlight the differences in NPV that can arise from using these evaluation methods in a top down and bottom-up approach. Results from three resource scenarios, derived from sampling a "virtual" ore body (reality) on grid spacings of 75m, 50m and 25m, are analyzed and compared.

May 1, 2007

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By M Fahey

Large volumes of tailings are produced annually by the goldmining industry of Western Australia. This material ishydraulically discharged into large storage facilities usingsub-aerial deposition methods. Much of the gold comes fromhighly weathered rock, resulting in tailings with significant claycontents. Consolidation of these materials can be very slow,particularly if occurring under the effects of self-weight alone.To optimise the consolidation behaviour of the tailings, disposalstrategies can take advantage of the effects of evaporation byallowing each tailings layer to dry before the next layer isdeposited. In the last 20 years, much of the gold processing inWestern Australia has utilised saline groundwater. As the salinetailings dry, the surface will develop a thin salt crust. Laboratorytests have shown that these crusts can drastically reduce thesurface evaporation, adversely affecting the behaviour of thestorage. This problem has been the focus of an extensive researchprogramme, with the objective of obtaining a fullerunderstanding of the mechanisms controlling the coupledconsolidation and evaporation behaviour of saline gold tailings.Part of this study involved site investigations of a wide range ofstorages to ascertain their current states. Methods of gainingaccess to the tailings following deposition were developed.In situ testing and high quality sampling were conducted on each storage and samples returned to the laboratory for analysis. These investigations have enabled full characterisation of the storages to be accomplished. Examples of data are shown herein and the implications of the results are discussed.

Jan 1, 2001

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006