Search Documents

By W. M. Myers

Jet is a substance of organic origin and has been defined by the U. S. Geological Survey as a "dense black lignite, taking a good polish, and sometimes used for jewelry". Jet is characterized by the lustrous, intense black surface it displays when polished. It is due to this property that the expression "jet black" is so commonly used to imply intense blackness.

Jan 1, 1923

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By Frank Parrish

History and performance data of 17 water-injection projects in Cooke and Grayson Counties in north Texas are presented for the purpose of studying and comparing operating practices and oil-recovery techniques. Water is injected into Strawn and Canyon sands of Pennsylvanian age. The principal formation flooded is the Strawn, which ranges in depth from 725 to 6,900 ft in the projects covered. Estimated ultimate recoveries range as follows: Primary, 22 to 494 bbl per acre ft; and secondary; 63 to 296 bbl per acre ft. These figures represent the following percentages of original oil in place: Primary, 10 to 46 pct; and secondary, 8 to 23 pct. Shallower projects; 725 to 1,500 ft in depth, had higher average primary and secondary recoveries than did deeper projects. Crude-oil gravity, which ranges from 20° to 45° API, was not relatable to yield of secondary recovery oil. Analysis of the data indicates that five-spot injection patterns will yield the highest percentage of oil remaining at start of flooding; that is, 28.8 pct for five-spot injection patterns, compared with 20.8 pct for line-drive patterns and 11.6 pct for random patterns. Waterflooding in this area appears to be very successful. Secondary recoveries of most projects are expected to nearly equal primary recoveries.

Jan 1, 1963

By Albert W. Deurbrouck

The percentage of coal cleaned mechanically has increased greatly in the past 30 years. This technological change in preparation methods, accompanied by mechanical innovations in most phases of coal mining, has enabled the industry to supply quality coals at competitive prices. The Bureau of Mines has contributed to this progress by conducting research on coal-preparation problems, by evaluating the performance of domestic-and foreign-made preparation equipment, and by recording advances as they occur in industrial coal-cleaning practices. The Bureau's work in this field is recorded in the more than 150 technical and scientific publications listed in this volume. These reports, published by the Bureau over the past half century, document the Nation's progress in a vitally important phase of fuel technology.

Jan 1, 1961

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

The refractory nature of residual gold in Kalgoorlie calcines is caused by occlusion in dense pyrrhotite formed by fusion within pyrite grains during decomposition. Fusion of pyrite increases as the rate of heating exceeds the rate of sulphur expulsion. By controlling these rates in relation to each other in a fluidised system fusion is limited and an expanded structure is formed. The increased area presented to cyanide solution, and the decreased diffusion distance, makes gold more accessible for extraction. Gold extraction from expanded pyrrhotite, before oxidation for porosity, is comparable with extraction from fully oxidised calcines from Edwards roasters. A method is suggested for standardised comparison of cyanidation residues.

Jan 1, 1957

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By Bruce Bryant

Silver ore was discovered at Aspen in 1879, but the district did not reach full production until 1888 after lawsuits were settled and railroads furnished less expensive transportation to the outside world. The boom years were 1888-92; production declined thereafter. From the middle 1920's until 1950, the Midnight mine in the Richmond Hill district furnished most of the output in the Aspen quadrangle. Since 1950, little mining has been done at Aspen. The metals produced were silver, lead and zinc. Native silver dissolved from the sulfide ores was redeposited by waters circulating as deep as 300 m below the land surface, resulting in great secondary enrichment of many of the deposits. Over 100 million ounces of silver were produced in the Aspen quadrangle. Low-grade lead-zinc deposits remain between the old workings locally, and data available suggest that primary ore below levels mined is also of low grade. The ore occurs in the Mississippian Leadville Limestone and the lower part of the Pennsylvanian Belden Formation in sites that were made favorable for deposition by a number of stratigraphic and structural factors.

Jan 1, 1982

By J. A. Botín

Identifying, quantifying and minimizing technical risks associated to investment decisions is a key challenge for the minerals industry decision takers and investors. However, risk analysis in most bankable mine feasibility studies are based on stochastic modelling of project NPV which, in most cases, fail to provide decision makers with a truly comprehensive analysis of risks associated to technical and management uncertainty and, as the result, are of little use for risk management and project optimization. This paper presents a value-chain risk management approach where project risk is evaluated for each step of the project lifecycle, from exploration to mine closure, and risk management is performed as part of a stepwise value added optimization process.

Jan 1, 2011

By Steve Kral

U.S. mines are among the most efficient, productive and safest in the world. Much of that efficiency is due to the high-technology equipment and processes available to the industry. The U.S. mining industry can produce more material now with fewer people than it could a few decades ago. And that material can be produced more safely. However, the workforce is growing older and fewer young people are filling the holes created by retirements. Even though mining is one of the highest paid occupations in the United States, young people believe they can find jobs that pay almost as well without the risks and the often remote locations associated with mines.

Jan 1, 2002

To mine uraniferous sand-stone in an economically feasible and environmentally compatible manner without placing men underground. Approach Uraniferous sand is remotely extracted through a single borehole by cutting Into the are around the borehole with a high pressure water Jet, and pumping the resulting slurry to the surface. How It Works A 16-inch-diameter borehole Is drilled from the surface down into the burled mineral deposit, and the mining tool Is installed. High pressure water Is released as a jet from a nozzle In the mining tool to erode the are, forming a slurry that flows to the bottom of the cavity. The slurry Is drawn Into Inlets located near the bottom of the drill string. See drawing. After being pumped to the surface, the slurry is weighed, metered, and checked for radioactivity. It is then deposited Into one of a pair of sumps. Water collecting in the sumps drains Into an adjoining pond for reuse. Thickened are In the sumps is removed and placed In piles.

Jan 1, 1978

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By E. L. Garton

Michigan is becomining one off the important oil-producing States of the country, The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 1935.4/ The Bureau of Mines method of crude-oil analysis and classification indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the tame amount of kerosene and gas-oil combined, 12 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue of about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in S counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By Paul H. Madsen, Victor S. Romero

The Tren Urbano project in Puerto Rico includes a 19 m diameter tunnel constructed by the stacked drift method, which involves installation of a pre-supported concrete arch using multiple tunnels. Geotechnical conditions consisted of weak rock and highly weathered, unstable alluvial soils. Due to low cover, reinforcement of the arch was required. Ground behavior ranged from firm ground to mixed-face to raveling and flowing ground. Consequently, construction of the individual drifts involved many different soft-ground techniques such as steel set supports, shotcrete support, shield tunneling, forepoling, and consolidation grouting. During construction, the design was modified to improve constructability. Although settlement was experienced during excavation of the drifts, arch movements were within predicted limits and minimal surface settlement was observed upon excavation of the interior.

Jan 1, 2001

By M E. Barley, A D. George, M Kneeshaw

Detailed pit and outcrop mapping of sedimentary rocks and their alteration is providing insights into fluvial processes that operated during deposition of the world-class Yandi channel iron deposit. Five prominent rock units are traceable along the strike of the Yandi deposit and permit correlation of open pits and mesas. These units are the Eastern Clay Horizon (ECH), granule-pebble conglomerate (GPC), Main Ore Zone (MOZ), Basal Denatured Zone (BDZ), and Basal Conglomerate (BCONG). The upper part of the deposit is characterised by a transition from spheroidal grains with well-defined rims and nuclei to larger, subangular grains with poorly developed rims. The distribution of rock types and sedimentary features such as lateral accretion surfaces, channel scours and fills, graded bedding, cross-bedding, reworked horizons, and slumped strata are common at Yandi and indicate deposition in a fluvial system. Bedding is well preserved despite modification of original grain shapes and textures and introduction of secondary silica and alumina in the upper part of the deposit. The high lithic and clay content of the GPC and ECH possibly reflect changes in source area or a hiatus in deposition of the Marillana Pisolite. The MOZ and the BDZ may be the same depositional unit with the latter recording alteration by groundwater and destruction of primary textures and other sedimentary features. The BCONG is a channel lag deposit reworked during deposition of the MOZ. This interpretation is supported by the dominance of basement-derived lithic clasts, the presence of BCONG clasts, the variable thickness of the unit along strike and the presence of BCONG clasts in the BDZ.

Jan 1, 2002

By S Hapugoda, A Poliakov, E Donskoi, L Lu

A significant amount of metallic iron in the world is produced in blast furnaces from iron ore pellets. To control the quality of pellets and to optimise pellet production, characterisation of both green and fired pellets is required. Optical image analysis (OIA) allows identification of different minerals, binder, remaining fluxes and porosity within pellets.For proper identification of the mineralogy, porosity and texture in pellets a high magnification is required, therefore each individual image covers only a very small portion of the pellet. At the same time the characterisation of pellets requires that the whole pellet is represented as a single object, so the size of the resulting overall image at high magnification can make it difficult to handle. A solution to this problem has been implemented within the CSIRO OIA package Mineral4 by combining images at different levels. Namely, to average out local irregularities, individual frames can be stitched during imaging into larger MosaiX images. Mineral4 further combines these MosaiX images into a single panorama image of the whole pellet.The proposed procedures allow the calculation of mineral and porosity spatial distributions, local gradients and abundance graphs based on the distance from the centre of the pellet. The ‘Pellets’ module of CSIRO OIA software also allows for characterisation of large irregularly shaped particles of lump ore and sinter.CITATION:Poliakov, A, Donskoi, E, Hapugoda, S and Lu, L, 2017. Optical image analysis of iron ore pellets and lumps using CSIRO software Mineral/Recognition, in Proceedings Iron Ore 2017, pp 583–592 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME 'is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959