Search Documents

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By F. Hassani, K. Moozar, J. Ouellet, P. Gauthier

"This paper describes a sudden spill of waste rock used for backfilling from a waste pass at an underground mine in Canada, thus causing a major failure/accident. The mine operator immediately launched a detailed investigation to understand the causes of this accident and develop procedures to prevent any recurrence of such events in the future. The authors from McGill University were invited to collaborate with the engineers at the mine to examine this accident. The events leading to the accident were studied, appropriate measurements were taken and samples of the waste material were collected for further testing and analysis.The field visit and the interview of the witnesses allowed the detailed documentation of the events. The sequence of events related to the incident, along with the experimental results obtained in the course of the investigation, are presented. The waste material was characterized in the laboratory with regard to its behaviour in the presence of water. This information is discussed and the failure mechanism involved in the accident is identified. Finally, the full recommendations as well as the immediate operational measures implemented by the mine to prevent the future occurrence of such events are presented and discussed."

Jan 1, 2004

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By Gary Almeraris, Vincent Jr Tirolo

Traditionally, “Means and Methods” were the sole responsibility of Contractors. However, because of a number of litigious projects in the 1970s, Owners and their Engineers began including Suggested Methods of Construction (SMC) in Contract Drawings. By the late 1990s these SMCs were becoming baseline “Means and Methods” with Contractor recommended changes often considered as Value Engineering proposals. By 2004, the word “Suggested” was sometimes changed to “Prescriptive.” Owners are also purchasing TBMs and other mining equipment for Contractors prior to bid. Is limiting the contracting community’s innovation in developing their own “Means and Methods” and selecting their own equipment in the best interests of the Owner? Does it reduce the Owner’s, Engineer’s or the Contractor’s risk? Are claims reduced and finally what is the impact on the bid? A questionnaire was sent to more than fifty senior engineering field and management personnel representing more than 30 heavy construction companies to ask their opinion on these questions.

Jan 1, 2005

By A. S. Odeh

During the last few years, several authors1-6 have advanced mathematical solutions, both exact and approximate, to the pressure behavior of a well producing from a region bounded by a circular discontinuity. The most recent solutions were reported by Carter, and by Bixel and van Poollen. Varter solved the appropriate equations analytically. Bixel and van Poollen reported a numerical solution and provided correlation charts for the interpretation of flow tests; their method uses an overlay technique and is valid for wide ranges of mobility and storage capacity ratios. The mobility ratio is defined as the ratio between k/p of the two zones, and the capacity ratio is defined as the ratio between $c of the two zones. We have developed independently an analytic solution, programmed for the CDC 1604, that agreed with Carter's.'1 The same differential equation, assumptions, boundary, and initial conditions were used. We ran 30 drawdowns and 30 buildups of a unit capacity ratio and of varied mobility ratios. We also varied the radial distances to the discontinuity, and the radii of drainage. We examined the results and obtained correlations that were simple to apply and useful in flow test interpretation. The results and the correlations reported here in graphical form allow the determination of the mobility of the two zones and the radial distance to the discontinuity. They eliminate the need to fit field data to a curve as is required in the overlay technique.6 Thus, the advantages of the present correlations are that they require less effort and they provide a unique answer. They also provide guidelines for selecting the parts of the flow test plot to be used in the interpretations. Moreover, the results obtained from the programmed analytic solution define the time intervals where the approximate solution reported by Hurstl and discussed by Larkin2 are applicable. Normal buildup and drawdown plots resulted in an early straight line, a long transition zone and a late (second) straight line. However, the second straight line will not occur if the drainage radius is not at least 10 times the radial distance to the discontinuity. The mobility of the imer and outer zones can be calculated from the slopes of the first and second straight lines, respectively, by the normal methods of the flow test analysis. We found that the radial distance to the discontinuity may be determined from the abscissa value for the point of intersection of the extensions of the two straight lines. Results similar to some of these were reported by Adams et aL7 The approximate solution compared favorably with the exact one during the first and second straight-line periods. However, during the transition zone, deviation occurred between the two solutions. Discussion of Figures Figs. 1 through 7 summarize the results of this investigation. On Figs. 3 through 7 there appears the equation of each respective plot. In this paper the mobility ratio M is defined as klp2/kzpl, where subscripts 1 and 2 refer respectively to the inner and outer zones, and dimensionless time = t, = 6.32 X In the investigation, M ranged from 0.25 to 50;

Jan 1, 1970

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By Lifeng Li, Jhon Silva-Castro

In a previous work, the authors analyzed the overlapping probability of two adjacent charges in a single hole for pyrotechnic and electronic detonators. This document extends such work to a complete mine blast where more than two holes are detonated. In a mine blast, all the blast holes are connected as a network by detonators to follow a given initiation sequence. Such initiation sequence’s performance is based on the adequate timing between charges in the mine blast. The analysis of the reliability of a mine blast based on the timing between charges and the initiation type is presented in this document. For a long-run time and under proposed operating conditions, the reliability of the mine blast can be analyzed based on the network which is treated as a system. The failure of the system is defined as no success between any two delays charges either in a single hole or in between two holes.

Jan 1, 2016

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By R. Q. Honaker

Dense medium processes are used to clean over 50% of the coal that is fed into preparation plant facilities worldwide. The dense medium is formed using ultrafine magnetite which is recovered after the cleaning step using drain-and-rinse screens and magnetic separators. Despite the high efficiency of the recovery system, magnetite losses of around 0.5 to 1.0 kg/ton are common. Considering the recent escalation of magnetite to around $300/ton, an alternative source of magnetic material from coal combustion bottom ash has been investigated. A relatively low cost recovery system has been developed. Dense-medium tests using the bottom ash magnetics revealed a high level of efficiency as indicated by probable error values around 0.03 over the range of medium densities investigated. The results from both the recovery and coal cleaning efforts will be discussed in detail.

Jan 1, 2009

The SFR system utilizes a skimmer or extractor placed at or near the slurry-froth interface where there is a higher concentration of valuable mineral particles. With assistance of hydrocyclones, it is possible to classify the extracted particles into coarse and fine particle streams, that can be handled separately. It also allows the coarser solids to be separated from entrained low-value fines. The first test results with the SFR system significantly improved both coarse and fine particle recovery in a flotation cell. The SFR system was tested in the flotation circuit at a copper-moly concentrator, and the results show that the use of the skimmer has huge potential to increase the froth recovery (Rf) of both molybdenum and copper.

Jan 1, 2012

By K J. Thompson

This paper describes the work which has been undertaken at the Ohai coalfields in Southland to restore overburden heaps during past opencast mining operations, and procedures which have been adopted to ensure that restoration is achieved concurrent with present opencast mining activities. The system implemented for the treatment of wastewater from opencast mining operati6ns is also described.

Jan 1, 1981

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Richard W. Graeme, James J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona project, located in Hualgayoc, Cajamarca Department, Peru, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, project development occurred against the backdrop of a presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as an unprecedented demand for engineering and technical skills. Project “Lessons Learned” are discussed in the context of an evolving strategy. The Cerro Corona project forms part of a porphyry copper-gold deposit situated within the Hualgayoc Mining District in northern Peru. It is located in the highest part of the Western Cordillera of the Andes, close to the headwaters of the Atlantic Continental Basin. It lies approximately 90 km (56 miles) by road north of the Department of Cajamarca’s capital city and near the village of Hualgayoc. Access to the Cerro Corona project from Cajamarca is by two roads, one from Cajamarca to the Yanacocha Mine 45 km (28 miles), and then from Yanacocha to the village of Hualgayoc and the town of Bambamarca 45 km (28 miles).

Jan 1, 2007