Search Documents

By S. L. Weber, D. E. Banks

"Silicosis was first reported by the ancient Greeks and is apparently as old as human history. The prevalence of this illness peaked in the last half of the 19th century and the early part of this century, when mechanized industry was developing and the relationship between dust exposure and disease was less well understood. Yet, even today in devel-oped countries, sporadic outbreaks of silicosis occur when workers are consistently exposed to silica particles of respir-able size (0.5 to 5.0 µm in diameter) at levels exceeding those recognized to be safe.Silicon dioxide or silica. is the earth's most abundant mineral. Silica is considered to be either free (i.e.. unbound to other minerals) or combined. Minerals with high amounts of free silica include quartz (including granite) flint. Chert, opal, chalcedony, and diatomite. Combined forms of silica are called silicates and include, among others, asbestos talc and kaolin.In the crystalline form, silica exists as quartz, cristobalite, and tridymite (Fig. 28). Of these quartz is ubiquitous in the environment and occurs as sand and as a part of many rocks. Cristobalite and tridymite occur naturally in lava and can be formed by the heating of quartz or amorphous silica. Cristo-balite is more tibrogenic than quartz. Amorphous silica is noncrystalline and, therefore, is relatively nontoxic and does not cause silicosis. It occurs as diatomite (skeletons of pre-historic marine organisms) or as vitreous silica (glass), the result of carefully melting and then quickly cooling free crystalline silica. Heating diatomite with or without alkali (a process known as calcining), forms cristobalite and adds the respiratory toxicity of free crystalline silica.There are many opportunities for occupational exposure to respirable crystalline free silica. Some of the commonly en-countered occupations in which the risk of silicosis exists are reported in Table 20.Silicosis. the pulmonary disease caused by the inhalation of silica particles of respirable size, is most commonly cate-gorized by findings on the chest radiograph. The most typical presentations simple silicosis and progressive massive fibrosis appear different radiologically but are grouped under the category of classic silicosis because they are a part of the radiographic spectrum of this illness. Radiographically, simple silicosis appears as small (less than 10 mm in diameter), rounded opacities, typically predominant in the upper lung zones. Progressive massive fibrosis is the result of the coalescence of these small nodular opacities and appears as larger opacities (more than 10 mm in diameter), again typicallydistributed in the upper lung zones."

Dec 1, 1995

By Byron S. Kutscher

This report summarizes the program to develop and construct an improved light-scattering dust monitor (ILSDM). This improved light-scattering dust monitor, which operates on the forward light scattering principle, provides instantaneous measurements of airborne dust concentrations in units of mg/m. The program was divided into two phases. Phase I involved the design of the ILSDM which was reviewed by the Bureau of Mines. Phase II included the fabrication of a prototype ILSDM based upon the design developed during Phase I. After completion, the ILSDM was delivered and demonstrated at the Bureau of Mines. A description of the final ILSDM design, operating instructions, maintenance instructions and recommendations for additional work are also included in this report.

Jan 1, 1980

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By R. Craig Smith

This report presents the software documentation for PREY AL, a prefeasibility mineral property evaluation program developed by the U.S. Bureau of Mines on a Lotus 1-2-3 spreadsheet. It is presented in a step-by-step "user?s manual" format. Appendixes contain the technical assumptions, program default values, and a summary printout detailing capital and operating costs and cash-flow analysis.

Jan 1, 1992

By Claudia Cooper

La autora desarrolla el importante papel que ha cumplido el sector minero peruano en la forja de un sólido entorno macroeconómico, que da sustento al incremento innegable en el estándar de vida de los peruanos y se constituye en base mínima para generar un mayor progreso. El arribo de grandes capitales mineros al Perú, no solo logró generar estabilidad cambiaria y de consumo en el país, sino también mantener cuentas fiscales sanas.

Dec 31, 2020

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By Y Yang

This paper discusses various issues surrounding the metallurgical control for furnaces, especially focusing on processes with long time-constants and æmetallurgical memoriesÆ. Examples will focus on furnaces accepting particulate and sometimes ill-defined feeds, eg submerged-arc furnaces, blast furnaces, secondary scrap smelting operations, recycling operations, waste incinerators, etc. Generally, because of the usually higher metallurgical time constant of these furnaces, these reactors have to be controlled in a feed-forward manner by the use of a hybrid of æblack boxÆ or empirical and ægrey boxÆ semi-empirical first principles metallurgical modelling and simulation techniques in a supervisory metallurgical control capacity.

Jan 1, 2000

By David Conover

Technological advancements in electronic sensors and mine-wide monitoring systems have improved remote monitoring and analysis of underground mining information. The effective use of . these systems for ground control applications, however, remains a challenge facing the mining industry. The U.S. Department of Interior, Bureau of Mines is conducting research, utilizing real-time acquisition of rock mechanics data, to provide mine operators the means to rapidly identify and manage potentially hazardous ground conditions. The Bureau has installed a remote monitoring network in a Colorado coal mine to record Pressures from instruments installed in the roof and pi1lars of gateroads and from transducers on shield-legs along the face. The field data are being monitored at the Denver Research Center, 150 mi from the mine. A computer at the Center analyzes the field data and generates graphic displays, which permit detailed examination of mine-wide ground conditions in real-time. For the first time, Bureau researchers are able to perform real-time monitoring and analysis of rock mechanics data while mining is in progress. The data collection and display capabilities of the system were effectively used to identify and evaluate face stability problems at the mine.

Jan 1, 1990

By S Winter, G Klenowski

During longwall mining in the Bowen Basin, open tension cracks formed by overburden subsidence occur to a height of about 175 m above the mining horizon. Within this zone, water in aquifers or inundated workings will flow into the mine.At the Oaky Creek mines Aquila seam, open cut pits containing pit water overlie German Creek seam longwall panels at a height of about 105 m. The highly saline water is classified as contaminated and cannot be discharged off-site. Because alternative water storage facilities were not available, innovative water management solutions were needed to allow longwall mining to proceed without underground flooding.Computer modelling and underground inflow measurements have been completed to accurately determine inflow rates into longwall mines from overlying water sources at increasing overburden heights. Research work has also included determining cost-effective blanket treatment of final voids and reshaping spoil piles to minimise downward seepage.Ponded water overlying the Aquila low, Grasstree south and A6 pits required remedial works prior to longwall undermining to prevent flooding. In the Aquila low pit it was necessary to partition the pit and remove water overlying longwall 32. Two in-pit bridges were constructed by dozing and track compacting low wall spoil. The final void above the longwall panel was kept dry during undermining. Maximum recorded underground inflow rate was 30.0 L/s.The Grasstree south pit final void, part of the ramp and much of the spoil piles were inundated prior to undermining of 308 panel. A bridge and blanket were required to prevent ponding above the longwall. Maximum recorded inflow during undermining was 23.2 L/s.The pit A6 south final void, which contained dumped, saturated rejects and inundated highwall mining entries was undermined by longwall 36 at the Oaky No 1 underground mine. Because mapping of highwall entries was not available, the maximum calculated inflow rate of 73.0 L/s was based on all design entries being fully inundated. The actual inflow rate during longwall mining ranged up to 20.0 L/s.Water management improvements that have been implemented include greater use of contaminated pit water to wash coal, use of evaporation fans, and installation of a 6 ML/day reverse osmosis plant for water purification.CITATION:Klenowski, G and Winter, S, 2017. Inflows into longwall mines from inundated overlying workings, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Rodrigo Afonso Hatwig

Os aços inoxidáveis duplex (DSS) e superduplex (SDSS) são ligas que se caracterizam por apresentar uma microestrutura composta por frações volumétricas similares das fases ferrita e austenita. Dependendo da composição química e do tratamento termomecânico aplicado, a microestrutura dos aços inoxidáveis DSS e SDSS poderá apresentar, além das fases ferrita e austenita, fases intermetálicas deletérias. Neste trabalho, um estudo termodinâmico-computacional foi realizado com o objetivo de acompanhar a evolução das fases de aços superduplex no intervalo de temperaturas entre 300°C e 1.200ºC. Para tanto, fez-se uso do software de simulação termodinâmica FactSage v. 6.4. Os resultados descrevem de forma eficaz as fases principais e secundárias em função da temperatura e composição química.

Aug 8, 2018

By J. A. Herbst

A state of the art computer simulation package, named UTAH-MODSIM is being developed. This package can run on a mainframe (eg. UNIVAC) as well as on a microcomputer (eg. IBM/PC with at least 512 kBytes of core memory). Friendliness was the major concern in developing this software. The user simply generates a complete flowsheet by presenting the flowsheet on a graphics terminal. This flowsheet defines the circuit to be simulated. With the minimum required data, the user can obtain a complete mass and water balances within a few minutes. Moreover, this package will provide scale-up and capital cost information of specified equipment relevant to design. In order to illustrate the utility of this software, three design examples are given. They are: a) A typical multistage crushing plant. b) A reverse closed grinding circuit comparing one stage with two stage classification. c) A standard closed grinding circuit suitable to liberate a specified fraction of chalcopyrite from a copper ore.

Jan 1, 1986

By Donald M. Liddell

ALTHOUGH the midday lunches of business associations have been re-echoing the phrases that re- search would lead us out of the depression and that the last place to economize is on research, nevertheless most executives apparently concluded that it was their neighbor who ought not to economize in research, and that in their own plants what had been discovered in 1929-30 was sufficient to lead them out of the wilderness. At any rate, I have discovered much less that seems worth noting, and compared with 1931, the report volume of the committee members is off about 40 per cent, and compared with 1929, about 80 per cent. Evidently there is some hookup with the +tee1 industry as to output, and the Report Reading Committee should investigate this and the relative use of commas and periods.

Jan 1, 1933

By Rogelio Frigerio

Ante el impulso de desarrollo económico de Argentina, surgieron técnicas para atacar su apogeo nacionalista. En ese sentido, el presente texto señala las tácticas de esta lucha oblicua contra el desarrollo nacional, que varían de acuerdo a las circunstancias y diversos campos (petróleo,carbón siderúrgia, química, transporte, automotores).

Nov 1, 1961

By K. C. Garner

The visit reported was made with support from the 1997 J.C. Boyle travelling scholarship. The management and control of hazardous gases released into the underground environment are an integral part of coal mining. The power-generations stations at Appin and Tower collieries, with a combined electrical output of 94 MW, have been operating for some time and have demonstrated a technology that is able to exploit the available gas fully. Contributory factors have been the development and introduction of directional drilling techniques, pre- and post-drainage of coal, relatively high seam permeability, a high gas content of the worked seam, high production rates and a willingness to embrace new ideas and technology

Jun 21, 1905

By N. Niyogi

La nacionalización de las minas de coque en 1971 y la toma de posesión de otras minas de la India originaron cambios en la industria minera del carbón. Por tal motivo, se estudiaron programas de racionalización para dirigir la industria minera hacia las tareas del futuro. En ese sentido, el presente texto señala los problemas de diseño e implementación del depósito de carbón de Jharia. Asimismo, se muestran las tendencias del desarrollo en el futuro utilizando el proyecto de la mina de carbón en Jharia.

May 1, 1982

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By M. Craig Miller

As the trend continues in the U. S. toward inceased capital investment in longwall mining equipment and wider panels. the risk also increases for gotential financial and production loses due to undetected geologic anomalies. This paper describes how RIM Sm (Radio Imaging Method) is utilized in conjunction with more traditional exploration and interpretive methods to delineate fluvial channels. displacement faults and poor roof conditions in a Southeastern Ohio coal mine

Jan 1, 1990

By King R. L

Low-enthalpy geothermal groundwater resources occur at relatively shallow depths in the Upper Cretaceous/1'ertiary sedimentary sequence in the on-shore Gippsland Basin. The main stratigraphic unit containing hot groundwater is the Latrobe Group. Groundwater temperatures in the range 30 to 70¦C have been recorded from depths between 500 and 1000 m. The hottest groundwater is in the Latrobe Valley and Lake Wellington depressions. Geothermal gradients in these areas range from less than 2¦C/100 m to over 10¦C/100 m (compared to a world average of about 3¦C/100 m). A number of theories have been advanced to explain the geothermal anomalies including exothermic reaction such as oxidation of coal, mixing with deeper, hotter groundwater and high geothermal fluxes along fault zones. Variations in geothermal gradients can also result from type and thickness (and hence thermal conductivities) of the sedimentary pile, depth to consolidated basement rocks, and influence of groundwater flow patterns including proximity to recharge zones. The hot groundwater in the Gippsland Basin has substantial potential as a source of energy for direct heat applications such as process heating, space and water heating for buildings, and agricultural and aquaculture. Geothermal energy has a number of environmental advantages over traditional sources of energy. It is clean, safe, causes minimal land disturbances and in most cases is naturally renewable.

Jan 1, 1992

By A. W. Khair

This paper deals with the analysis of pillar failure in a room and pillar mining operation of a deep underground coal mine. The incident here involved the failure of more than 100 pillars. The mechanism of pillar failure (bump/squeeze) has been studied in detail. The analysis consists of inmine eyewitness observations, laboratory experiments and analytical study of the pillar failure area using finite element technique. Results indicated that the mechanical properties of coal, roof and floor, geologic condition, and the method of operation have affected the mode of pillar failure. Hard roof and floor prevented roof caving and floor heaving in the gob area creating an inhomgeneous stress field on the pillar. This condition developed a yield zone and a core zone in the pillar. Progressive increase of vertical stress further increased the yield zone of the pillar and reduced the core pillar leading to a total squeeze of the pillar. However, the analysis indicated that the pillars were liable to bump provided any sudden shift of load occurred on the core pillar due to some dynamic shock imparted by a local failure of the immediate roof (slickenslided area) or during splitting.

Jan 1, 1986