Search Documents

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

A mineral survey of the Rough Hills WSA (Wilderness Study Area) in northeastern Nevada was done by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The WSA is comprised of 6,685 acres of mountainous, desert lands within the Elko District of the Bureau of Land Management. The survey entailed investigations of prospects or mineral occurrences to provide information on possible resources within the WSA. No mineral resources were identified in the WSA. The only historical mining activity was for placer gold at the Prunty prospect at the confluence of Copper Creek and the Bruneau River. Total gravel at the prospect is about 6,500 cubic yards; however, the survey showed significant gold values (greater than $0.10 gold per cubic yard) only in the southwestern portion. There, however, the gravel averaged less than $1.00 gold per cubic yard, and only about 3,000 cubic yards are present, a grade and yardage insufficient to be of commercial interest. The occurrence, however, may have value for recreational mining by hobbyists.

Jan 1, 1986

By J. P. W. Bennie, A. de Jong, G. M. Denton

Mintek together with Middelburg Steel & Alloys, developed the DC arc furnace process for the production of ferroalloys with the expressed objective of smelting ore fines (<1mm) without the need for agglomeration. In the case of ferrochrome production, the DC arc furnace, being a semi-open bath operation, loses radiant energy directly from the bath to the furnace roof and sidewalls above the melt. This energy loss is reflected in a higher electrical energy usage per ton of alloy than for a submerged-arc operation smelting lumpy ores or sintered pellets. The difference increases still further when pre-heated sintered pellet feed is used in a submerged-arc operation. This shortcoming of the DC arc furnace can however be overcome by preheating the feed to the furnace in a fluidized bed or flash reactor fuelled by cold furnace off-gas. In addition to fluidization and preheating testwork, various preheating flowsheets with associated mass and energy balances have been developed and compared from a techno-economic viewpoint. The three major advantages identified were: a) fluidized beds can preheat ores and fluxes up to 950°C without sticking and defluidizing, b) the open bath DC arc furnace does not require expensive coke or char to maintain the burden porosity and, c) the capital cost associated with the milling, pelletising and sintering plant falls away since ore fines are used directly.

Jan 1, 2004

By Thomas M. Brady

The Spokane Research Laboratory/NIOSH and the University of British Columbia (UBC) geomechanics group are focusing on the development of safe and cost-effective underground design guidelines for weak rock masses having an RMR in the range of 15 to 45. Weak ground conditions, ground support, and mining methods used in several North American underground mines were observed. The RMR values were calculated to update both manned entry span design and non-entry stability graphs, plus a database on underhand mining methods was created to reflect existing North American mining conditions. The immediate rock mass was characterized and analyzed in terms of prevailing type of ground support, potential failure mechanisms, and rock behavior to define how existing design curves must be modified for the existing weak rock mass. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making sound economic decisions that will also ensure a safe working environment.

Jan 1, 2006

Over recent years the trend in Australia has been towards the definitions of sustainable development which emerged from the 1992 Rio Summit of retaining a commitment to ecological integrity, but also incorporating social and economic dimensions of sustainability. Sustainable development may be seen as maintaining and enhancing:natural capital: defined as all natural resources, both environmental and those of traditional economic value; manufactured capital: made by human kind; including produced goods, infrastructure and built environment; human capital: defined as the health, well-being, intellectual capabilities and spiritual welfare of individuals; and social capital: defined as social relations and institutions within and between societies, their norms and functionality (Ameef, 2002). This paper will endeavour to assess the challenges and opportunities facing the professionals and their Institute in the minerals industry in Australia because the MMSD Global and Regional Australia Reports do not, in the authorÆs opinion, adequately address the æhuman capitalÆ input into the current or future development of the minerals industry, in particular, the sustainability of the professionalsÆ skills, knowledge and experiences in a global context.

Jan 1, 2002

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture&apos;, 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By H. Hurkchand

Background: A cross-sectional study was conducted in November2001 to establish the prevalence rates of Human Immunodeficiency Virus (HIV) and sexually transmitted infections (STIs) (Chlamydia trachomatis and Neisseria gonorrhoea) in a coalmining town in Mpumalanga. Methods: 155 adults were recruited (79 males and 76 females), by holding community meetings, and by door-to-door recruitment. Saliva and urine specimens were collected for the analysis of HIV and STI prevalence, respectively. Results: The mean age for males was 31.35 years (min = 19 yrs and max = 50 yrs) and the mean age of the female participants was31.90 years (min = 17 yrs, max = 49 yrs). The prevalence of HIV was found to be 22.78% [95% CI (14.09?33.59)] in the males vs. 47.37%[95% CI (35.79?55.16)] in the females, [p = 0.001, OR = 3.05, 95%CI(1.49?6.26)]. The prevalence of C. trachomatis was 7.90% [95% CI(2.95?16.39)] in the males vs. 12.86% [95% CI (6.05?23.00)] in the females, p = 0.324. The prevalence of N. gonorrhoea was 3.79%[95% CI (0.79?1.08)] in the males vs. 9.86% [95% CI (4.06?19.26)]in the females, p = 0.137. HIV was significantly associated with C. trachomatis, [p = 0.032, OR = 3.18, 95% CI (1.04?9.72)], but was not significant when stratified by gender. HIV was not significantly associated with N. gonorrhoea (p = 0.072) but it was significantly associated when stratified by gender, p = 0.001 for females. There were no significant associations between HIV and age (p = 0.408), even upon stratification by gender. Conclusions: HIV prevalence in this community is high, and corresponds to national figures. However, the prevalence of STIs is surprisingly low as it would be expected to be high in a migrant population. Although communities are exposed to expanding peer-education activities that encourage behaviour change, the prevalence of HIV in this group. There is an urgent need for interventions designed to treat or prevent HIV infection in women generally and in women at high risk. Keywords: HIV prevalence, STI prevalence, antenatal, mining

Jan 1, 2005

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. But wait a minute: Isn&apos;t head loss a negative number, a debit? And isn&apos;t fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves - pressure losses as negative values and energy additions as positive values-and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Feb 24, 1997

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

By Cari Deyell, Brigette Martini

The AntaKori Cu-Au-Ag Project in the Hualgayoc mining district, northern Peru is a complex system dominated by calcic Cu-Au-Ag skarn hosted in Cretaceous sedimentary units. The skarn system is partially overprinted by two younger epithermal systems: high sulphidation (HS) epithermal gold-copper-silver mineralization related to the adjacent Tantahuatay system, and intermediate sulphidation carbonate-base metal Au-Ag-Pb-Zn-Cu mineralization related to late stage rhyolite stocks and flow domes (Wilson, 2012).

May 1, 2008

By R. G. Knickerbocker, David Schlain, F. K. Shelton, J. H. Jacobs

"Many manganese ores contain from 0.1 to several percent cobalt. If such ores arc used for the production of ferromanganese, the cobalt is lost; on the other hand, if they are used for the production of electrolytic manganese, the cobalt can be recovered during the purification of the electrolyte.The production of cobalt in the United States is insignificant compared to the amount consumed, most of which is imported from the Belgian Congo. Cobalt-bearing manganese ores may therefore constitute an important reserve of cobalt in times of emergency. Moreover, the combined value of manganese and cobalt in some ores may be sufficient to warrant the recovery of both metals by the electrolytic manganese process, whereas the recovery of either manganese or cobalt alone might not be economically feasible.In view of the potential importance of manganese ores as a source of cobalt, a survey has boon made of the cobalt content of manganese ores. Most of the data have been obtained from analyses made in the Bureau of Mines, but valuable data have also been obtained from publications of the Geological Survey, various State publications, and other sources. Unfortunately, most published analyses of manganese ores do not include cobalt determinations; when such analyses were fairly detailed, but did not include cobalt, it was presumed that cobalt was not present in significant quantity.Information on the cobalt content of domestic manganese ores is given in table 1. Ores containing 0.1 percent or more cobalt are listed in table 2, and the districts in which such ores occur are shown in figure 1. Most of the known cobalt-bearing manganese ores occur in the southeastern part of the United States. A group of deposits in central Arizona and a few scattered deposits in other States also' contain cobalt."

Apr 1, 1946

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By Camila Magalhães Gonçalves

O aço inoxidável ferrítico tipo 430 estabilizado com Nb, com e sem recozimento após laminação a quente, foi laminado a frio e submetido a recozimentos isotérmicos em temperaturas de 650ºC, 700ºC, 750ºC e 800°C por 900 s para análise da evolução da textura de recristalização e do tamanho do grão via técnica de EBSD. Ocorreu o refino do grão após recristalização, resultando em um tamanho final de 12,2 mm. Observou-se um aumento da intensidade das componentes (111)[12 1] e (111)[01 1] da fibra g e diminuição na intensidade da fibra a de deformação. A componente cubo girado, característica do aço laminado a quente, desaparece com a recristalização. As propriedades mecânicas desse aço, principalmente o comportamento em estampagem profunda, são diretamente afetadas por sua textura de recristalização.

Jan 16, 2018

By S. H. Yi, J. R. Kim, Y. S. Lee

The viscosities of CaO-SiO2-Al2O3-MgO-FeO slags were measured under conditions ofCaO/SiO2=1.15–1.6, 10–13 percent Al2O3, 5–10 percent MgO and 5–20 percent FeO. Slag viscosity decreased with increasing FeO content at a fixed basicity (CaO/SiO2) of slag. Slag viscosity at low FeO (<7.5 percent FeO) exhibited a minimum value by increasing MgO content in slag. Viscosity decreased with increasing slag basicity up to 1.3 while it increased as slag basicity increased from 1.3 to 1.5. Thus, it was proposed that the driving force for the decreases of slag viscosity would be an increase in depolymerization of silicate network at C/S=1.3, while the viscous behaviour at C/S>1.3 would be increased with increasing the chemical potential of primary solid phase e.g. dicalcium silicate. A thermodynamic approach for the activity of primary solid phase in molten slags resulted in a reasonable relationship between viscosity and slag components. Therefore, it was confirmed that slag viscosity in basic slags system (C/S>1.3) could be determined by the chemical potential of dicalcium silicate. Keywords: viscosity, basicity, bosh slag, blast furnace, slag structure, FT-IR

Jan 1, 2004

This paper sets out to discuss how alluvials - particularly mineral sands, tin and gold have adjusted to meet the problems of lower grade and more difficult physical political and economic conditions. The mineral sands industry seems to have adapted satisfactorily but less so with tin and gold.

Jan 1, 1996

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent upon the application, mineral properties and available instruments. Different instruments produce images that display different features; in order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application.

Jan 1, 2001

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jan 1, 1965