Search Documents

By Daniel Horta Fernandes, Walter Gomes de Albuquerque, Adriano Cesar Carvalhido, Victor Dias Martins

O trabalho apresenta a experiência recente da troca de 38 staves contribuindo no prolongamento da campanha operacional do Alto-Forno 3. Durante 13 dias ocorreu a substituição dos Staves originais de FoFo instalados em 1999 por novos Staves de cobre fundido. Além da recuperação do sistema de refrigeração, a mudança no material dos Staves contribui para maior troca térmica favorecendo a formação carga inativa (cascão) que protege os Staves e o corpo do Alto-Forno. Esta substituição foi fundamental para recuperar a estabilidade da temperatura da carcaça e prolongar a vida útil do equipamento até o final de sua campanha. Diversos aspectos do projeto serão apresentados: engenharia, metodologia, planejamento, segurança, qualidade técnica, cronograma e outros.

Oct 1, 2019

By João Luiz do Vale

In standard wear tests, such as pin on disk (ASTM-G99) or block on ring (ASTM-G77), the apparatus simulates conditions that are often different from a machine element real application. Therefore, for an accurate investigation of a tribological application, it is essential to test the real condition in which there are similarities as: geometry, contact details, force application mode, materials, among others. It emphasizes that for studies involving polymeric materials it becomes extremely relevant. Thus, the Laboratory of Surfaces and Contact (LASC) at UTFPR developed an apparatus for sliding bearing on shaft test. In that equipment, loads are applied by a dead-weight system and the frictional force is measured on a load cell. The apparatus operating ranges for load added to the dead weight system and rotation shaft are from 0.2 to 5.0 kgf and from 260 to 3500 rpm, respectively. This paper presents a detailed evaluation of such apparatus, which includes free-body diagrams analysis and a deduction to obtain an equation for the kinetic friction coefficient. Also, the standard measurement uncertainties of a caliper, an electronic scale, and a cell load were determined. It was verified that the kinetic friction coefficient equation is dependent on the apparatus geometry, the applied load, and the frictional force value. Additionally, through the statistical significance analysis it was concluded that some terms in the equation were not significant. Finally, through the application of the error propagation theory in the kinetic friction coefficient equation, the standard measurement uncertainty of the apparatus which showed a value nearby 0.002 along the operating range of the apparatus was obtained.

Jul 31, 2018

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Amanda Sardinha Pereira

O uso dos aços 2,25Cr-1Mo-0,25V em reatores de hidrotratamento cresceu significativamente devido ao seu excelente comportamento em fluência, elevada tenacidade e resistência à corrosão. Contudo, as propriedades mecânicas deste material podem ser afetadas pelo tipo de microestrutura. O objetivo desse trabalho foi estudar a influência da microestrutura do aço 2,25Cr-1Mo-0,25V, obtida por meio de diferentes tratamentos térmicos, na difusividade e solubilidade de hidrogênio. Foram realizados ataques químicos seletivos para revelar a austenita retida e ensaios de permeação eletroquímica do hidrogênio. A análise dos dados da permeação mostrou que a amostra revenida a 550°C (Dap = 4,6 x 10-12 m2/s) possui menor coeficiente de difusão comparada às amostras revenida a 375°C (Dap = 6,9 x 10-11 m2/s) e revenida a 730°C (Dap= 3,4 x 10-11m2/s).

Aug 8, 2018

By Luiz Alberto dos Santos

. In this work, samples of the alloy with composition of 50.9 % at. Ni were machined and were subjected to hot tensile test, after the machining all the samples were solubilized so that all were in the same condition during the hot tensile test. The hot tensile tests were performed between the temperatures 350-650°C and the yield stress were between 800 and 597.1 MPa and area reduction between 17 and 75% with respect to the initial area. The test at 350°C shows a fragile fracture characteristic while the hot tensile test above this temperature showed a predominantly ductile fracture. The fragile fracture is evidenced by the river marks that are characteristic of this type of fracture, because in this condition does not promote much plastic deformation. The higher temperatures present ductile fracture, because present the dimples that also characterize this type of fracture. This work shows the temperature relationship in the mechanical properties, more specifically the hot tensile test, in the NiTi alloy.

Oct 30, 2017

By Valdeci Paula Alvarenga

Os aços alto carbono possuem maior resistência e dureza, e menor dutilidade em relação aos aços baixo e médio carbono. O aço carbono SAE 1070 é um aço plano classificado como alto carbono e possui uma microestrutura predominantemente perlítica. Algumas possíveis aplicações desse aço são: fitas de serra, lâminas para raspagem, lâminas de corte para indústrias agrícolas, entre outros. O processamento desses de aços em toda a cadeia produtiva sempre é desafiadora. O objetivo principal foi caracterizar e melhorar a microestrutura perlítica do aço SAE 1070 laminado a quente produzido na Aperam visando reduzir ou eliminar o custo adicional dos clientes de relaminação durante o processamento em suas linhas de produção. Foi possível através de análises e simulação termodinâmica refinar o grão austenítico e melhorar as propriedades mecânicas do aço SAE 1070 produzido na Aperam e como consequência a melhoria da laminabilidade a frio desse aço.

Oct 30, 2017

By Wolfgang Kern

More and more coke oven plants worldwide face the task to improve their emission reduction at their coke oven batteries. In the 90’s PROven® was invented and developed by DMT to regulate the inner pressure of a single coke oven chamber. Generally, most of the coke oven chambers can only close and open their connection to the collecting main but without the possibility to regulate the pressure during the carbonization time. Through the installation of PROven® the load on the coke oven door sealing system and the charging lids will be decreased and so does the emissions of crude COG as well. The current PROven® system, installed in the collecting main, does not only regulate the chamber pressure, it replaces the valve between the goose neck and the collecting main, too. This variable pressure control allows decreasing the leakages at the emissions sources to a minimum and allows operating the collecting main under optimum pressure. Subsequently, this will lead to enhanced emission reduction. PROven® proved its value with more than 2,100 units installed by licensee worldwide. Nevertheless, DMT is always focused on its client’s needs and therefore enhance PROven® to provide the Best Available Technique (BAT). Among the main features of the now available system is the plain arrangement with a higher reliability and the possibility to install the system outside of the collecting main without modifying it. Hence, upgrading coke oven plants during operation is possible without any noticeable impact on the plant operation.

Aug 1, 2018

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019

By Caio Trindade Almeida, Tharcysio Oliveira Rocha Paiva

Tharcysio de Oliveira Rocha de Paiva2

Oct 3, 2019

By Thamyres Moura Lima

O presente trabalho, traz a analise eletroquímica, curvas de polarização,das ligas Ti-35Nb-xTa (x = 0; 2,5; 5,0; 7,5)Ta (% em peso) anodizadas, a um potencial de 20V e 1hora e sem anodizar , para verificar o aumento da resistência a corrosão dessas ligas. O meio ao qual os ensaios foram realizados foi o sfb ( fluido corpóreo simulado).Obtendo como resultado que as ligas anodizadas apresentam maior resistênciaa corrosão nesse meio. A liga sem adição de tântalo obteve menor densidade de corrente, assim tendo uma maior resistência a corrosão após anodizada o que não ocorre sem a anodização.

Oct 30, 2017

By Márcio Lobato Genelhu

Este trabalho tem o objetivo de apresentar o modelo de recuperação refratária a quente dos regeneradores dos altos-fornos, através da técnica de solda cerâmica, visando o aumento da vida útil e evitando a parada prematura para a manutenção destes equipamentos. A aplicação da solda cerâmica prolongou a vida útil dos regeneradores.

Aug 8, 2018

By Amilton Ferreira de Oliveira

Este trabalho se propõe a mostrar os resultados obtidos pela SunCoke Energy Brasil após as mudanças do perfil da mistura de carvões, na qual foram acrescidas criteriosamente as participações dos carvões denominados “soft” e carvões “steam coal”, seguido da redução também criteriosa dos carvões médio voláteis. A consolidação dos dados de qualidade do coque e do custo das misturas comprova que as modificações no perfil das misturas foram bem sucedidas, pois a qualidade do coque se manteve conforme a expectativa dos clientes (Altos-Fornos) e o custo das misturas apresentou uma significativa redução. Todos os testes e experimentos adotados foram embasados na utilização na metodologia denominada “Método e aparelho para avaliar as propriedades de coqueificação do carvão”, também conhecida como Box Test, e ainda no profundo estudo das características dos carvões utilizados e os impactos destes na qualidade do coque.

Aug 16, 2017

By Lucas Rosate Leite dos Santos, Erica Marcelino Freitas de Souza Silva, Glaucio Soares da Fonseca

Aços Inoxidáveis Austeníticos (AIA) são largamente utilizados não somente por sua boa resistência à corrosão, mas porque eles são amplamente conformáveis, fabricáveis, duráveis e soldáveis por praticamente todo os processos. À temperatura ambiente, as ligas homogêneas forjadas são, em geral, completamente austeníticas. Entretanto, para muitas aplicações essas ligas necessitam ser submetidas a processos metalúrgicos como a soldagem, que por sua vez pode causar modificações microestruturais. Desta forma, uma liga que antes era completamente austenítica pode apresentar frações de ferrita- δ retida. O presente trabalho investiga a influência do aporte térmico na evolução da microestrutura de solda do AIA 316L submetido à solda similar em dois diferentes aportes térmicos pelo processo TIG Autógeno. A análise microestrutural das amostras soldadas, foi realizada via Microscopia Ótica. Os resultados possibilitaram concluir que o aporte térmico de fato influenciou na microestrutura final do 316L, pois após a soldagem, para ambos aportes aplicados, a microestrutura foi composta de austenita e ferrita-δ e não apenas predominância da austenita como inicialmente apresentava o Metal Base.

Oct 7, 2019

By Delciane Porfiro, Tiago de Mattos Serodre, Antônio Eduardo Clark Peres, Valdirene Gonzaga de Resende

The evaluation of the effect of the addition of carbon nanotubes (NTCs) directly to a etheramine on the flotation recovery of the quartz at pH 10.5 was carried out by means of microflotation tests in Hallimond tube. The quartz flotation was evaluated using 0.1% (w/v) etheramine solution with different percentages of carboxylic functionalized NTCs. The increase in the percentage of functionalized NTCs increased the flotation recovery to a maximum and from this it was observed a reduction of the recovery of the mineral. Pure etheramine and etheramine with the NTCs were characterized by FTIR spectroscopy and thermal analysis. FTIR spectra of both pure etheramine and etheramine with NTCs clearly showed peaks with the same wavelengths and diagnostics of the cation etheramine and acetate anion. Thermogravimetry indicated that the etheramine + NTCs-COOH mixture lost approximately the same weight percentage over a larger temperature range. In addition, the interaction of the nanotubes with the etheramine caused them to decompose at a lower temperature.

Oct 3, 2019

By Fabrício Tibúrcio Silva Araújo

O AutoLog é uma solução em tecnologia de automação e informação para controle absoluto do carregamento e descarregamento de caminhões em um grande cliente no ramo de fertilizantes. Seu objetivo é garantir uma operação autônoma que otimize os lucros e reduza os custos em logística. Este trabalho visa demonstrar o problema que originou a solução, a metodologia utilizada no seu desenvolvimento e o seu objetivo final.

Oct 30, 2017

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

In Potiguar West, in the regions of Vale do Açú, Mossoró, and Chapada do Apodi there are limestone outcrops of about 20 thousand square kilometers (with a thickness ranging from 50 to 400 meters). Limestone is an essential raw material for the manufacture of agricultural products and especially for construction. The rock serves for various productions, among them is used for the production of cement, lime, fertilizers, even ornamental rocks. Thus highlighting the mineral potential in the state of Rio Grande do Norte, as well as its use in the production of various products.

Oct 3, 2019

By Miguel Araújo Vasconcelos Filho, Ulisses Tetti

In order to determine the influence of the number of increments of the sinter sample on the variability of the chemical composition obtained in Sinter Plant production, a variographic study was carried out. It was performed with two series of samples. The first series was composed of 40 samples with a 6-second interval, with the objective of obtaining the so-called minimum practical error, resulting from the extraction processes of the sample of the conveyor belt and preparation and analysis in the laboratory and the second series composed of 60 samples with a range of 4 minutes, which points to the sample selection error. The results obtained showed that the minimization of the sample selection error occurs for increments spaced in 15 minutes, being in agreement with ISO 3082, but with significantly better results than those currently practiced for intervals between 1hour increments. It was then decided on the suitability of the sampler to allow hourly increments to be collected and on a second opportunity to install a sampling tower with primary and secondary samplers to collect increments every 15 minutes including sample size reduction.

Oct 1, 2019

By Jéssica Vicente Luiz, Rayander Martins Pimenta, Everton Pedroza dos Santos

The Hybrid Pelletized Sinter (HPS) is a agglomeration process that involves the combination of conventional sintering and pelletizing techniques and can be used with the purpose of obtaining improvements in the agglomeration stage of iron ore, and one of the great advantages of the process is the use of a wide particle size range of the ore. In this way, the superfines of low-cost ores, which are improper in sintering, can be used in the HPS process for the formation of the quasi-particle. The use of HPS with the sintering plants of the industries presented throughout the study, enabled an increase in productivity, decreased fuel utilization and reduced slag formation in blast furnaces. Thus, the present study aims to present a review of the literature on the Hybrid Pelletized Sinter (HPS) process and its main characteristics, as well as the results obtained by the companies that adopted the process.

Oct 1, 2019

By Willian dos Reis Lima, Breno Totti Maia, Guilherme Silva Machado, Adeilson Roberto Ribeiro, Carlos Alberto de Souza, Douglas Augusto Pena, Fabrício da Silveira Garajau, Marcelo de Souza Lima Guerra

Oct 1, 2019

By Gleison Vinicius Ricardo, Luiz Cláudio von Sperling Cotta, Artur Frederico Fonseca da Cruz, Evandro José de Castro Lopes

Binders are important raw materials in the iron ore pelletizing process. The bentonite, most usual, has been used in plants of this process since the forties due to its good performance in the agglomeration of ultrafine ore, although the silicon content in bentonite impairs the total iron content of the pellet, reducing its market value. This article studies the bentonite consumption reduction and improvement of the chemical quality of pellets by the addition of an organic binder in the productive process of Vale Vargem Grande pelletizing plant. By evaluation of variables as, drop test of green pellet, green pellet, dry pellet and fired pellet compressive strength tests, tumble index, percentage fraction of lower than 5 mm and total iron content in fired pellets, it was possible to approve the technical availability of the organic binder auxiliary in Vargem Grande pelletizing process. Nonetheless the positive influence of total iron content increase due to the reduction of bentonite consumption, it could also verify no impact on the physical quality of the pellets under the same production rhythm, approving once again the use of organic binders in pelletizing process.

Oct 1, 2019