Search Documents

By E. S. Bumps

A series of macrographs are presented for the purpose of graphically recording the strain phenomenon that accompanies the energy transition in the Charpy impact testing of a mild steel that is susceptible to strain aging. STRAIN patterns in mild steel Charpy impact specimens were obtained in order to determine whether, on the first appearance of plastic strain during deformation, the initial fracture cracks appear in the region of plastic strain or in the elasti-cally deformed regions between. Although this attempt to locate the initiation of cleavage was not successful, the observed strain patterns illustrating various stress conditions in partially deformed Charpy specimens are presented along with a discussion of the possible dependence of transition energy on the yield phenomenon. Earlier work on the development of strain patterns in mild steel have been reported by Fry1 and later by Jevon.2 Harris, Rinebolt, and Raring3 observed characteristic strain markings on the surface of Charpy V-notch impact specimens fractured above and below the transition temperature which they presented schematically. It is intended that the strain figures presented here will add to the literature a graphic correlation of strain with transition energy in impact specimens. Samples of % in. round hot rolled, 0.20 pct C steel were machined to standard 0.394 in. sq, V-notch Charpy impact specimens. Preliminary testing involved determination of transition temperature, Fig. 1, using a Sontagg impact tester. These data were subsequently used to select temperatures above, within, and below the transition range at which specimens were partially deformed. Partial deformation was obtained by either varying the energy or the testing temperature, see Table I. Macroscopic strain figures shown in Figs. 2 to 19 were produced by several metallographic repolish-ing and etching steps. The macroetchant used was as follows:4 120 g HCl, concentrated; 100 ml water; and 90 g cupric chloride. Strain figures were obtained on the outer surface and on sections through the central portion of the impact specimens in order to determine an approximation of the volumetric strain pattern. In the tensile strain figures reported by Jevon, it was found that strain etching would not work immediately following strain unless the material was heated to 200°C. The impact strain patterns presented here were obtained without this heating, but the specimens were not etched until ten months after straining. This confirms a discussion of Jevon's paper, in which it was pointed out that strain figures can also be developed after aging for long periods of time at room temperature. Hardness of the strained and unstrained portions, revealed by the etched pattern, was explored using R, impressions converted to R, hardness values. Discussion of Results In the impact test, as in the tensile test, some parts of the specimen yield and deform plastically, while other regions are deformed only elastically. The plastic deformation bears a relation to the imposed stress pattern. In the strain figures presented here, the plastically deformed regions are the dark etching ones. The strain figures are always symmetrical because the stress state in the Charpy-type specimen under impact loading is symmetrical. The difficulties encountered to produce initial cracks are intimated in Figs. 2 and 4. At a temperature of —75ºF, the stress was not sufficient to pro-

Jan 1, 1953

By J. J. Jakosky

A REVIEW of the progress in applied geophysics during the recent depression years reveals marked advances "over the methods employed several years ago. Of late, geophysical work has been curtailed to a con-siderable extent in the fields of oil and base-metal exploration, its especial domains a few years ago. Greater attention has been directed toward the use of geophysical technique in other engineering problems. Constantly maintained research programs have developed new instruments and per-fected better field, laboratory and interpretation techniques based on experience and skill acquired from years of application in the older geophysical field. During the past two years, geophysical methods have been employed in problems that required information on thickness of fill materials and subsurface bedrock contours. Considerable success has been attained, with subsequent drilling checking the predicted depths within one to five per cent. In general, these problems were similar as far as the fundamen-tal physical and geological conditions were concerned, but they have varied widely in specific detail and in engineering aspects. Character-istic of the different problems are: (1) yardage and bedrock profile in gold-placer mining; (2) water supply, involving underground drainage and storage conditions; (3) bedrock contours in dam-site and other structural investigations; (4) gravel and fill yardage, and other structural features along rights of way and in rock and gravel quarrying. Of particular interest, perhaps, to mining men are the problems of gold placer deposits and water supply. Geophysical work on gold placers is of especial interest because of the present expanded activity in all phases of gold mining. The development of a suitable water supply at, an economical cost is often of prime importance in insuring a successful mining venture. Particularly is this true in the arid Southwest. How-ever, the use of geophysical work in water supply is not confined to the needs of mining development.

Jan 1, 1933

By Thomas Egleston

The process of lixiviating silver ores, which do or do not contain gold, by means of hyposnlphite of soda is likely to assume a very great importance in the West, the conditions being such that while it is applicable to very rich ores which do not contain lead enough to smelt, it is also equally applicable to many ores that are either too poor or too impure to be treated by any other process. Western ores are generally divided into four classes: those which contain copper enough to be smelted for copper, from which the gold and silver is extracted in the wet way, as is the practice of the Boston and Colorado works; those in which there is a large quantity of lead, which can be smelted for lead, and the gold and silver extracted from it; ores in which there is neither copper nor lead enough to allow of a process of smelting, but which can be treated in pans, these ores being " free milling " if they require no metallurgical treatment, or '(rebellious" if they have to be roasted with or without the addition of salt; and ores which do not contain enough either of lead or copper for smelting, which are poor both in silver and gold, contain large amounts of sulphur, arsenic, and antimony, and cannot be treated in many places in the West by any of these processes. Roasting with salt would convert the base metals as well as the silver into chlorides, and would give in the amalgamation a very base bullion, and the expense of the process would be SO great that the margin of profit would be very small, the reason being that for the ordinary process of pan-amalgamation, which is the only one suitable for ores containing small amounts of the base metals, and poor in silver and gold, the cost of a plant for milling is so large as not to justify the expense of treating such ores. The electrolytic processes which have been partially successful in Europe have not been tried 'here. While in the near future they will undoubtedly be used, it is hardly possible to consider them now.

Jan 1, 1884

By R. H. Richman

Coarse-grained Fe-Ni-C martensites formed at subzero temperatures were strained in compression at room temperature and the plastic deformation modes examined as a funclion of carbon content. At very low carbon levels, defovmation occurs hy wavy slip; commencing at about 0.05 pct C, mechanical twinning accounts for an increasing proportion of the plastic flow. Beyond approximately 0.4 pct C the deformation appears to be entirely by mechanical twinning. The habit planes of the operative twin modes were determined to be (113), (0131, and "(089)" in decreasing frequency of occurrence. Some of the implicaticms of Ihe o6served deformation modes upon the structure and properties of ferrous martensites are discussed. METALLURGISTS have long sought to explain the mechanical properties of ferrous martensites, particularly the extraordinary hardness and strength of the high-carbon varieties. Until recently the lack of precise knowledge of the structure of martensite crystals was the most serious barrier to understanding; however, the advent of thin-foil techniques for transmission electron microscopy has removed much of the mystery from martensite structure. Observations by Kelly and Nutting,"' and many others since, indicate that Fe-C based martensite crystals are internally twinned to a degree dependent upon the carbon content, and that a martensite plate containing 0.8 wt pct C or more consists of a stack of twin-related lamellae with each lamella on the order of l00A thick. Such a structure would be expected to influence greatly all aspects of metallurgical behavior, and many of the properties of Fe-C based martensites have been rationalized accordingly. Recent independent experiments led Winchell and cohen3 to conclude that the strength of ferrous martensite is derived primarily from solid solution hardening of the iron lattice by interstitial carbon atoms. Strength contributions from precipitation, dislocation-atmosphere interactions, clustering, short-range order, crystallite size, and so forth, were considered to be of secondary importance. In the view of Winchell and Cohen, the twinned structure of martensite serves mainly to limit the effective length of dislocation lines in the lattice, and thereby confers an added measure of hardening. Few properties of metallic crystals are as sensitive to metallurgical structure as are deformation mechanisms. It is somewhat surprising therefore, that, except for metallographic evidence of mechanical twins in strained martensite,4 no systematic examination of plastic deformation

Jan 1, 1963

By M. Kaufman, D. Rosenthal

IT would be of great importance to our understanding of the phenomena of fracture in metals if a unique relationship could be established between stress and some easily measurable parameter of deformation up to the fracture. It is known that no such relationshir, has been found when the parameter was the mechanically measured strain,' the major part of which is plastic. The present investigation was initiated to determine, among other things, if the X-ray or lattice strain" might be a • For the definition of lattice strain see ref. 2. more suitable parameter. To this end, annealed stress free*' specimens of 61s aluminum alloy were ** Freedom of stress in this particular case means absence of those stresses which can be checked by the technique employed. tested at room temperature and liquid nitrogen temperature (—195OC), by first maintaining the same temperature from the beginning until the end of the test, and then with crossovers from one temperature to the other. Three major factors had to be taken into consideration in designing the specimens and testing equipment. The test setup must allow X-ray pictures to be taken while the specimen is under load (for as much as 2 hr at a given load). Provision must be made for maintaining the test specimen at the temperature of liquid nitrogen as well as at room temperature. In addition, the specimen must be able to rotate to allow the X,ray beam to take in as large a sample of grains as possible, to maintain centering, and to correct for effects of large grains. The final design of the specimen and equipment is shown in Figs. 1 and 2. The specimen and grips are hollow, enabling liquid nitrogen to be poured in through a funnel-container arrangement while the specimen is rotating. The diameter of the specimens at the 2 in. gage section is 5/16 in. with a 3/16 in. diameter hole through the center. A small pilot valve in the lower grip allows a very small stream of liquid nitrogen to escape, thus assuring circulation of the liquid at all times. A low temperature silicone grease-tissue paper packing is used to seal all joints. The specimen is held in the grips by a pin. Spherical socket joints at top and bottom are used to allow for proper alignment. The grips are connected to the thrust bearings by means of plastic couplings to decrease the heat flow. Rotation is accomplished by means of a motor which drives a plastic gear (integral with the lower coupling) through a semiuniversal joint to allow for deforma- tion of the specimen. The torque applied to the specimen is very small. The maximum stress caused by this torque at the highest loads reached was found to be less than 200 psi, The whole unit was mounted in a 10,000 Ib testing machine. An insulation cage was placed around the specimen to cut down air circulation, and consequent frosting of the specimen, and also to reduce radiation and convection heat losses. A narrow window, covered on both sides with a thin plastic materiai allows the X-ray beam to reach the specimen. Thermocouples placed just outside the pilot hole at the lower grip, in the bottom of the funnel container and near the top of the funnel container permitted checks of the

Jan 1, 1955

By M. Yokoi, K. Yoshida, T. Ishihara

The solubility of aluminum in cryolite melts has been determined by measuring the weight loss of aluminum submerged in melts contained in closed silicon nitride crucibles. The solubility in pure cryolite has also been checked with radioactive isotopes. The solubility decreases with increasing A1203 concentration, decreasing temperature, and decreasing cryolite ratio. The change of aluminum solubility in pure cryolite with the activity controlled by using Al-Ag and A2-Cu alloys supported the assumption that aluminum would dissolve in the form of monovalent ions according to the reaction 2AI + A1' —3 A1'. DURING the electrolytic production of aluminum, the electrodeposited metal redissolves in the bath in some form and is subsequently oxidized back to the former ionic state. This dissolution is believed to cause a decrease in current efficiency. Reported data on the solubility of aluminum in cryolite melts are scattered. The mechanism of the dissolution has not yet been determined, although certain tentative interpretations have been proposed. Many previous studies were performed under different test conditions. Studies were performed in open Systems and closed systems,'o and some were apparently not given sufficient time to Saturate." The solubility can be determined either analytically or gravimetrically. The analytical determination involves measurement of hydrogen gas evolved when frozen cryolite bath saturated with aluminum is treated with sodium hydroxide or hydrochloric acid. The gravimetric determination, adopted by many investigators,'-37'3>14 involves measurement of weight loss of the metal after equilibration with a known amount of salt. It appears that the former technique yields much smaller values of solubility than the latter technique. This large difference in results strongly suggests that the dissolved metal in the cryolite melt is no longer in the metallic state. In the present study, the solubility was determined by the gravimetric technique at various activities of aluminum using A1-Ag and Al-Cu alloys. An attempt was also made to determine the ionic (or atomic) state of the dissolved metal from the solubility data. 1) EXPERIMENTAL Apparatus. Preliminary tests demonstrated that silicon nitride was suitable as a container material since it is compatible to both the fluoride melts and molten aluminum. Crucibles were made from silicon powder nitrided with Nz gas at 1600°C. The good compatibility between crucible and melts is due to the near perfect nitrogenation of silicon. Only small amounts of silicon were found in the aluminum metal after the experiments. The crucible dimensions were 90 mm inside height, 38 mm ID, 105 mm outside height, and 50 mm OD. Close-fitting lids made of silicon nitride were also prepared. The crucible was placed in a close-fitting graphite crucible heated by a vertical Kanthal furnace, Fig. l. The lid and crucible are fastened tightly together by the condensation of vaporized bath in the narrow gap between them. The temperature was measured in the wall of the graphite crucible and controlled within * 5°C. The temperature difference between the measuring point and the interior of the melts was initially determined. Materials. The materials used were: Greenland cryolite (impurities CaF,, 0.5 pct; AlzO3, 0.2 pct; high-purity aluminum metal (purity 99.99 pct); A1203 and AlF, (provided by Nippon Light Metal Co., Ltd); reagent-grade NaF and CaF2; and 99.9+ pct Ag and Cu. Powdered reagents were carefully dried before use. A1-Ag and A1-Cu alloys were prepared before the experiments; their composition was checked by analysis

Jan 1, 1969

By Waldemar Lindgren

At the time of the discovery of America the old world had a scant supply of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the mines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia arid some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon made the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 1, 1917

By Robert T. Pring

In addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company' estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor, Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the Process. Methods of Dust Control "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are: in order .of their desirability, as follows: 1. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom prac tical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1943

By F. N. Rhines

I. An Outline of the Theory of the Sintering of Pure Metal Powders SINTERING may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, q, 28, 34, 38, 50, 52, 54 a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." II. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A. The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature.28 Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light contact,"' as do those of many other substances, including nickel." b. Upon compression the strength of the bond is increased progressively.28 There is a limit of pressure

Jan 1, 1946

By C. Burton Clark, J. Spotts McDowell

Refractories are defined as "materials having the ability to retain their physical shapes and chemical identities when subjected to high temperatures," or as "nonmetallic materials suitable for the construction or lining of furnaces operated at high temperatures." While resistance to "high" temperatures is thus the primary requirement for refractory materials, it is by no means the sole requirement. They must be able to withstand thermal shock resulting from rapid heating or cooling; other stresses induced by temperature change; pressures from the weights of furnace parts or contents; mechanical wear (abrasion) resulting from movement of furnace contents; and chemical attack by heated solids, liquids, or gases. Refractories of many kinds are needed for the many and widely diversified industrial applications. Those in greatest demand are classified on the basis of composition or properties into a few main groups, known as alumina-silica, silica, basic and insulating refractories. In each of these groups there are several classes. In addition to those included in the main groups, there are various special refractories, including silicon carbide, carbon, zircon, zirconia, alumina, and several others. Alumina-silica refractories comprise two main divisions: fire clay and high-alumina. The alumina content of fire-clay refractories covers the range from about 45 pct to 18 pct, and the silica content from 50 pct to 80 pct. The alumina content of fired high-alumina refractories ranges from about 99 pct to 45 pct, and the silica content from about 0.5 pct to 50 pct. Silica refractories of the different classes contain 94 pct to 97 pct silica. Basic refractories include periclase (magnesite), chrome spinel, forsterite, and dolomite. Refractory materials, including insulating firebrick, are supplied mainly as preformed shapes. Other products include bonding mortars and high temperature cements, ramming mixtures, plastic firebrick, hydraulic setting castables, dead-burned grain magnesite, and dead-burned dolomite. Refractory brick are classified on the basis of their physical form as Standard Sizes and Special Shapes. The Standard Sizes are brick of certain definite sizes and relatively simple design which are used in sufficient amounts to permit quantity production. The brick most widely used are the standard 9 in. X 4 ½ in. X 2 ½in. and 9 in. X 4½in. X 3 in. straights and corresponding series of sizes. All brick of nonstandard dimensions are regarded as "special shapes." They include a wide variety of brick regularly used for specific services, such as baffle tile for boilers, checker brick for regenerators, and others; together with shapes of special design manufactured on particular orders from designs submitted by the user. Not included in the broad classifications of Standard Sizes and Special Shapes are several specific-service refractory products, usually made by companies which specialize in their manufacture, or in some cases by the consumers themselves. These products include

Jan 1, 1960

By Wheeler P. Davey, Robert T. Phelps

A study of solid solutions has long been a source of interest because of the conditions controlling their formation. X-ray investigations so far have been conducted with the idea that there were two types of solid solutions. In the first type, an atom of the solute was supposed to replace an atom of the solvent in the crystal lattice. In the second type, an atom of the solute was supposed to lie in one of the interstices between the atoms of the solvent. These pictures both require that the sizes of the atoms must play an important part in the process of solution. It is the purpose of the present investigation to study the mechanism of solid solution, using pure silver as the solvent, and pure aluminum as the solute. X-ray measurements show that these elements have the same "shape" of atomic domains1 (they both crystallize as face-centered cubes) and that their atomic diameters differ by less than one per cent.' The results of the present investigation point toward a chemical rather than a physical picture of the nature of solid solution, and make the older pictures merely special cases of a more general picture. The new theory has the advantage, too, that it offers a rational explanation of certain phenomena which hitherto have been only interesting detached facts. The aluminum-silver system which was chosen for this study has been studied by various methods by several workers. By means of thermal analysis Gautier2 and Petrenko3 have determined the phase diagram. Hansen studied the aluminum-rich alloys by means of thermal and microscopic analyses. He showed that at high temperatures silver dissolved in aluminum to the extent of 47 per cent by weight at 560" C. But this solubility decreased to 1 per cent at 200" C. Westgren and Bradley5 made an extensive X-ray study of these alloys. They used the change in the lattice parameter of silver as a criterion of the solution State College, Pa.

Jan 1, 1932

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type3 Prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution. The alternatives to retreat mining with multiple entries are: Modified retreat mining- where the tail-entry is being formed during the mining of-the panel ("2"-system). Some form of advance mining-where the head-entry or both head and tail entries are being formed as part of the longwall extraction process. These methods are well-known and well-established. Variants of them are being practiced in Canada, Central and South America, but not in the US. It is primarily the laws governing ventilation-conceived for room and pillar mining which prevent the rapid development of these techniques. Another aspect of longwall mining is that it requires a systematic and consistent approach in organization, roof control, ventilation and transport. It is for this reason that compliance with health and safety regulation is fairly well ensured if the longwall system has been well laid out and is subsequently well-run. Nevertheless, a management mentality raised in the great flexibility of the room and pillar system cannot always come to terms with the degree of forward planning and rigid discipline required to successful longwall mining. Research, development and other investments in the partial aspects of longwall mining are always of interest, but no massive trend to longwall can be expected realistically unless these major stumbling blocks in the basic law and basic approach are effectively removed.

Jan 1, 1980

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.' Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,' it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

AISI constructional alloy steels are a series of steels in which a numbering system signifies the chemical composition limits. SAE (Society of Automotive Engineers) and AISI (American Iron and Steel Institute) use basically the same numbering system. The steels contain, in part, alloy additions of chromium, molybdenum, nickel, and vanadium. They are used widely in the automotive industry but have not been adopted for high temperature service. The purpose of this investigation was to study changes in microstructure observed in typical AISI constructional alloy steels in the welded and un-welded conditions after exposure for 34,000 hr at 900" and 1050" and, in several instances, 1200°F. The tensile and creep rupture properties after exposure for 10,000 hr were also evaluated. The investigation is a continuation of the work previously discussed. Little was known concerning the existence of graphite in medium or low carbon steels before 1943. It is important to note that continued exposure at elevated temperature is required in order to develop graphite in steels. Interest in the presence of graphite in steel, and also in changes in the properties of steels after long service at elevated temperatures, developed after 1943 when a failure of a welded joint of high temperature piping was associated with the graphitization of a relatively low carbon content steel with 0.50 pct Mo,8,0 Numerous investigations have beeen made in recent years studying the relationship of this type of failure to changes in properties. Attempts have been made to evaluate the performance of a number of steels, particularly in the heat-affected zone of welds. It was the unfortunate failure of a weld-heated zone in high temperature piping in the steam-power industry which focused attention upon possible failures, and upon the need for improved steels for high temperature piping service. Investigation by the National Tube Div., U. S. Steel Corp., Lorain Works, has included a wide variety of steels in an attempt to learn the effects of numerous factors and elements upon the long time performance of steels, although many of the compositions studied will never be used at elevated temperatures.1,4-7 Included were the well established AISI steel series, which offered opportunity to test moderately high carbon content steels as well as observe the effect of nickel, chromium, molybdenum, etc., upon the properties of these well known steels. The properties of the AISI steels were also studied for comparison with the previously reported properties of the Cr-Mo steels, now used by the steam-power industry.5,7 Materials and Testing Procedure The AISI alloy steels in Table I were exposed for 10,000 and 34,000 hr at 900°, 1050°, and 1200°F.

Jan 1, 1958

By B. F. Fackenthal

One of the practical questions presented to the blast-furnace manager, with regard to which little help can be obtained from existing technical literature, is the manner of filling and blowing-in. This operation is often performed according, more or less, to traditions which have come down from earlier practice, and which, if not positively detrimental when followed with the large modern furnace, may at least be greatly improved, just as the running of the furnace itself, while in blast, has been improved. It is not necessary, as many of the old furnace-men believed, to make a lot of white or silver-gray iron at the start, or to spend many weeks, or months even, in bringing the furnace to its normal burden. It has seemed to me that the publication of carefully-recorded data of practice on this point may be interesting to the members of the Institute engaged in the management of blast-furnaces. The enlarged blast-furnace at the Durham Iron Works, Riegelsville, Pa., owned by Messrs. Cooper & Hewitt, of New York City, was first put in blast February 21, 1876, since which time it has made seven blasts, and is now running on the eighth. A description of the furnace-plant, together with a record of the fifth blast, was given in my paper read at the Chattanooga meeting, May, 1885 (Transactions, xiv., 130). After some of the early blasts the furnace-lines underwent considerable change, and I have thought best to accompany this paper with drawings showing the lines and the tuyere-arrangement (see Plates I. and II.), and to give also the following summary of the conditions and results of each blast. During the first and second blasts no coke was used, and the furnace ran very irregularly, showing a constant tendency to scaffold, which was attributed, in great part, to the small hearth and other defective lines. The large proportion of air required at this furnace is accounted for by the fact that the engines are defective, and do not deliver into the furnace the amount of air indicated by the pistondisplacement.

Jan 1, 1890

By L. D. Jaffe, J. H. Hollomon

THE effect of tempering temperature and time upon the properties of quenched steel is clearly a subject of great practical importance, as well as of considerable theoretical interest. It would be very desirable to be able to predict the properties of a quenched steel when given any selected tempering cycle, with a minimum of experimental work upon that heat or even type of steel. Two problems are involved: one consists of relating the structure obtained to the physical properties, and will not be discussed here; the other, with which this paper deals, involves the relations of time, temperature and composition with the structure obtained on tempering. Indentation hardness is perhaps the most convenient quantitative measure of the tempered structure, or of what might be called the "degree of tempering." Undoubtedly, it is not an exact measure, and in some cases (as when temper-brittleness occurs) pieces of the same quenched and tempered steel may have widely differing properties at the same hardness. However, hardness has the advantage of being simple to determine and is certainly the most widely used indication of the degree of tempering. Moreover, for fully quenched steels that are not temper-brittle and do not contain retained austenite when quenched, it appears that, in general, if the hardness of the steel is the same, the tensile and impact properties will also be identical, whether a high or a low tempering temperature is used. The tempering charts available in the metallurgical literature usually give the hardness as a function of tempering temperature for only one tempering time. However, in practice, tempering times frequently vary, and a method of converting tempering curves for one time to tempering curves for some other time would be very valuable. It is also advantageous, in determining the tempering treatment necessary for a given part, not to have to temper samples at several temperatures for the time used for the commercial tempering operation. A more satisfactory procedure would be to employ times of the order of 10 to 30 min., rather than 5 or 10 hr., and if possible to use only one temperature. Furthermore, it is frequently desirable, for reasons such as temper-brittleness,* to obtain a given hardness with short times at relatively high temperatures, and it would be convenient to be able to compute without tests the time required to produce this hardness. Remarkably few quantitative studies of the hardness of quenched steel tempered over wide ranges of temperature and time

Jan 1, 1945

By Fred C. Bond

The process of comminution by grinding is properly classified as an art, rather than as a science. Like most other operations concerned in ore dressing, or in the treatment of nonmetallic minerals, the mathematical relationships of rock breaking are still obscure, and much disputed. If some basic formula exists, comparable for instance to E = RI in electricity, it has not yet been placed in common use. The absence of such a comprehensive mathematical background undoubtedly is the cause of many inefficient designs and installations, as well as of much poorly oriented experimental work. On the other hand, the mathematical immaturity of the process constitutes an opportunity for a real contribution on the part of those who enjoy mental pioneering. Some of the statements made in any such exploratory work may be little more than opinions, and it is to be expected that some will later be proved untrue; but such an evolutionary development is necessary if we are ever to arrive at the fundamental laws, the discovery of which can change the empirical art into a mathematically exact science. The most significant principle of comminution that we possess is probably Rittinger's law, which states that the work done in crushing or grinding is proportional to the area of the new surface produced. There is an alternative theory, known as Kick's law, which formerly was preferred to Rittinger's but which now is rather discredited. According to Kick, the work done in comminution is proportional to the volume, or weight, of the pieces broken, or to the cube of their diameters, while according to Rittinger it is proportional to the square of the diameters. Careful determinations of size distribution below the limit of sieve sizes1 indicate strongly that under ordinary grinding conditions the amount of new surface area produced is directly proportional to the net power input. Changes in the size ratio between the balls and the particles cause important differences in the proportion of the product that passes a given mesh size, but do not affect the total amount of new surface area; they merely change the distribution of the surface among mesh sizes. The principle of constant surface area is the logical result of Rittinger's law, and it may well have an important bearing on the comminution theories of the future. Formula for Ball Wear Grinding tests have been made in the Allis-Chalmers laboratory for more than 9 years, using a standard charge of mixed balls of different sizes; and a continuous record has been kept of the rates of wear of each size. These results have been combined and plotted in various ways in order to discover the relationship that exists

Jan 1, 1943

By A. William Johnson

It was pointed out in an earlier paper1 that our understanding of the atomic mechanism by which diffusion occurs in metallic alloys is scarcely in an advanced state. This unsatisfactory condition is the result not of any lack of interest, but of the difficulty of designing experiments that .will yield suitable data. The diffusion coefficient of an alloy, measured in the usual way, is simply a number specifying the rate of homogenization of a nonhomo-geneous metal; this number, of itself, can furnish neither the rate at which the individual atoms move nor information as to the mechanism by which they move. It does not necessarily follow, however, that such information cannot be obtained, even if the path to be followed is still not clear. Much success has been attained in the study of diffusion in ionic crystals. A number of experiments, for which there are few counterparts in connection with metals, yield information often indicating a detailed mechanism by which diffusion probably occurs. From such work, quite acceptable theories of lattice imperfections have been developed by Wagner, Schottky, Frenkel, Jost and others.2 It is postulated that real crystals of stoichiometric composition contain, in equilibrium, certain imperfections of which the most importarlt types are: (I) vacant cation sites, with an equal number of interstitial ions; (2) vacant anion sites, with an equal number of interstitial ions; (3) equal numbers of anions and cations in interstitial positions; (4) equal numbers of vacant anion and cation sites. The classification of a particular crystal according to this scheme then follows from studies of the variation of electrical conductivity with pressure of the electronegative component surrounding the crystal, with ion size, and with temperature; other physical phenomena, such as the Hall effect, have aided in establishing the classification. The relative mobility of the anion and cation may be determined by chemical analysis of the salt at the electrodes following electrolysis. With such information, and knowing that one ion never occupies the lattice site normally belonging to an ion of opposite sign, it is usually possible to ascertain the diffusion mechanism. It is clear that the same experiments are not applicable to metal crystals, and substitute experiments that yield as much information have not yet been devised. Much can be learned, however, about the mobilities of the two* kinds of atoms in alloys by the use of radioactive metals as indicators. Only one such experiment has been performed in the past. In 1933, Seith and Keil,3 in an effort to explain the great difference between the rate of diffusion of gold in lead and of lead in lead, measured the rate of diffusion of radioactive lead in 3 gold-lead

Jan 1, 1942

By M. B. Bever, A. B. Michael

THE structure of cast A1-Si alloys is altered profoundly by modifying agents. Sodium, in particular, reduces the size of the silicon particles in the eutectic and tends to change their shapes from plates to nearly rounded grains. This refinement is accompanied by a shift of the eutectic to higher silicon concentrations and lower temperatures. Similar effects can be attained by rapid solidification. Hypotheses advanced to explain modification have involved the formation of a ternary eutectic,1 the removal of oxides by fluxing,' and even a presumed allotropic transformation of silicon. Other hypotheses assume that the modifying agent causes an envelopment of the silicon particles by the aluminum-rich solid solution, but attribute this envelopment to different mechanisms. According to various explanations, the growth of the silicon particles is obstructed by an immiscible sodium-rich liquid," an adsorbed layer of sodium,' or a ternary compound;5 his obstruction has been conceived as purely mechanical or as a colloidal action.' It has also been proposed that sodium reduces the surface tension on the Al-Si interface, thus permitting the aluminum-rich solid to grow faster and to envelop the silicon particles.? Still other hypotheses stress undercooling and the attendant change in the rate of nucleation of silicon, but fail to ascribe any definite function to the sodium addition." '" Procedure High-purity alloys of aluminum and 3 or 7 pct Si were treated with modifying agents containing radioactive sodium tracers. The experiments were intended to investigate the partition of sodium between the primary aluminum-rich solution and the eutectic, and, if possible, to determine whether sodium is concentrated in or around the silicon particles in the eutectic. Radioactive sodium fluoride, alone or mixed with stable sodium chloride, was allowed to react with the alloy for 5 min immediately before solidification in the crucible. Modification could not be attained with additions of less than the equivalent of approximately 0.1 pct Na. Some alloys were not completely modified, but comparison of the structures of treated and untreated specimens indicated a very considerable reduction in particle size of the silicon in all of the former. A treated alloy is shown in Fig. 1. Radioactive sodium fluoride was prepared by bombardment with deuterons having an energy of 14 mev. This bombardment (totaling, for example, 6 microampere-hours in one run) produced radioactive Na24 (half-life 14.8 hr) by the reaction 11Na23 (d,p) 11Na24. The radioisotopes of fluorine also produced have short half-lives and were not detected. A half-life determination by counting confirmed that the measured activity was due to Na24. The distribution of the sodium in the solidified alloys was determined by an autoradiographic technique by which a suitable stripping film is attached to a very thin metallographic specimen. After exposure and development, this emulsion remains superimposed on the specimen and may be examined microscopically or photographed by reflected light. The emulsion of the autoradiograph can be correlated directly with the underlying surface by simple adjustment in focus. The details of this technique have been described elsewhere." Results Fig. 2 is a micrograph of the autoradiographic emulsion ("autoradiograph") lying directly above the area of eutectic in Fig. 1. Fig. 3 shows a similar autoradiograph of a region consisting of primary solid solution. The small black dots (tracks) in these autoradiographs are developed grains in the emul-

Jan 1, 1954