Search Documents

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By S. B. Casey

[ ] IN 1880, an electric arc was struck over metal for the first time to experiment with controllable melting. The glare of this arc has reflected on the stacks of the steel industry and continued to light the path of steelmakers in their never ending quest -for faster, more economical, and better ways of producing steel. William Siemens is credited with first employing the electric arc to melt metal in a closed hearth and produce basic metallurgical reactions. By the turn of the century, an Italian, named Stassano, was experimenting with ore reduction by the electric arc. In 1899, Dr. Paul Heroult, in France, used the direct arc principle for producing ferro-chromium. His experiments quickly led him to develop a dosed-top arc furnace for the production of steel, and his first commercial shipment was recorded in December, 1900. American steelmakers, quick to sense the possibilities of this method of melting, invited Heroult to our shores, where, in 1905, he was responsible for installing the first arc furnace on the North American continent. This furnace, at Sault Ste. Marie, was built for ore reduction. But Charles Holcomb, founder of Holcomb Steel. Co. of Syracuse, N. Y. contacted Heroult in 1905 and contracted for the first American direct-arc electric furnace for steelmaking. On April 5, 1906, the first heat was tapped from this 3-ton unit. The furnace was basic lined and powered by a single-phase, 500 kw generator, -producing high amperage at low voltage. It is interesting to note that, although the first few heats were made with cold charges, subsequent heats were duplexed. R. H. Bully, first superintendent of Holcomb Steel, persuaded the directors to purchase the unit to effect a more economical and efficient means of making tool steel by duplexing prime melting in a combustion fired furnace, and transfer of hot metal to the arc furnace for temperature adjusting, refining, and adding carbon and alloying elements. Today, duplexing is foreseen by some as the steelmaking process of the future. The promise shown by America&apos;s first arc furnace for ingot production quickly led to the purchase of a similar unit by The Firth Sterling Steel Co., in 1909, and to the purchase of the first arc furnace for production of steel castings, by the Treadwell Engineering Co., in 1911. From its humble start in 1906, production of arc furnace steel has never ceased to increase its yearly percentage of total steel production in the U. S., although certain other methods have declined or almost disappeared. By its ability to be used intermittently, the arc furnace gained favor and enhanced its reputation during depression days. When the attack on Pearl Harbor plunged us headlong into the long days of World War II, the arc furnace stood ready, flexible enough to be overburdened hearth wise 30 pct and power wise 25 pct, pouring its endless flood of alloy for the guns, tanks, ships, and planes which ultimately brought victory. During the post war boom, the now, proven virtues of low initial cost, faster installation, better yield, improved availability, and lower operating cost, enabled industry-particularly the small, new, independent producers-to locate strategically and profitably to meet the demand of an America that had been starved for new homes, appliances, cars, and highways. In the Korean police action, the arc furnace again proved itself by providing the latest alloys metallurgists could develop to meet the demands that the jet age and the innovations of guided missiles required. In today&apos;s peacetime prosperity, the arc furnace is continuing to provide the economic flexibility required to meet an ever increasing demand for better steel in the face of mounting costs, scrap shortages, and pressure toward decentralized location of industry.

Jan 1, 1961

By Augustus Locke

In 1900, when. the public first heard of "secondary enrichment," the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners&apos; astonishment, they carried chal-cocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales&apos; advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this argument. Especially pertinent was the proof that (1) the deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accomplished more easily than that of pyrite, enargite, or chalcopyrite. The microscopic evidence has been accumulating for ten years and it demands

Jan 1, 1924

By B. E. Mix

THE present methods of unloading ore and coarse-crushing at the Magna plant of the Utah Copper Co. are the developments of the past five years. Hand dumping and breaking have given way to the rotary car dump and large gyratory; and the bucket elevators and stationary screens have been replaced by conveyors and shaking screens. The coarse-crushing plant may be broadly divided into two units: the primary crushing and the secondary crushing, or primary roll, unit. The former was erected in 1923; with the exception of the excavation, the construction was carried on by forces of the company. Excavation was started in the middle of March, the first concrete was poured July 16, erection of the steel building started Oct. 30, and the unit was com-pleted and operating Dec. 30. The unit has a capacity of over 24,000 tons of ore per day, and cost more than a million dollars. Remodeling of the primary-roll unit extended over a period of years preceding this, some of the work having been done as early as 1918.

Jan 8, 1925

By J. K. Buehler

With the rapid acceleration of the cost of shovel dippers and major standard shovel clipper rebuild components, maintenance management at Kennecott Copper Corp.&apos;s Bingham Canyon mine initiated a dipper maintenance and rebuild program. The program focused on extending the service life of the shovel dipper, reducing field labor in maintaining dippers, and lowering shovel dipper rebuild costs. While comprehensive evaluation of the program is still underway, preliminary benefits of the program indicate: •Reduced field ,gelding for shovel dipper field maintenance, •Fewer dipper rebuild units entering the shop, and •Reduced dipper rebuild costs per unit.

Jan 1, 1979

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE studies of the mechanism of precipitation and of the resulting property changes in aluminum-silver alloys1-3 have presented some new concepts of the aging reaction-concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.1,4 These platelets grow in lateral dimensions and in thickness with aging time until they are thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstätten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuous precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 EXPERIMENTAL PROCEDURE The alloys were made using 99.97 per cent Al or distilled magnesium, with

Jan 1, 1943

By T. A. Rickard

The interior of West Australia is an arid table-land, elevated 1400 feet above the sea. This plateau is flanked to the south by the Tertiary limestones which fringe the Great Australian Bight. It is bordered northward by the Carboniferous beds of the Fitzroy river and westward by the granite of the Darling hills, while to the cast this wide area, about 900 miles square, slopes downward imperceptibly into an undulating plain of sand, which stretches with dismal persistence across the boundary of South Australia. The waters of the ocean receded from this tract of land long ago; it is probably the oldest landsurface on the globe, and represents the basal wreck of a much larger continent. Fig. 1 is a map of this region. The Coolgardie and Kalgoorlie gold-fields are situated in the southwestern part of the region. The rock-formation consists of granite penetrated by diorites and andesites. The latter are occasionally associated with tuff&apos;s, which have been readily mistaken for sedimentaries. There are no fossil-bearing rocks, such as would afford a datum-line from which to measure the relative geological age of the prevailing formation. On the extreme edges of the mining territory there are, it is true, remnants of sand-rock which are considered identical with the " Desert Sandstone " of Queensland, determined by Daintree to be of Mesozoic age. But even this formation has evidently been laid down so long subsequent to the underlying rocks that it serves merely to emphasize their much greater antiquity. In their characteristics and in their relations to each other, the granite and the diorite of the Coolgardie region appear to me much to resemble the Laurentian granite and the Huronian

Jan 1, 1899

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By M. N. Shetty, A. C. D. Chaklader

RECENTLY, it has been demonstrated that a considerable densification and interparticle bonding can be achieved if a pressure is applied to a powder compact while the material of the compact is undergoing either a decomposition reaction&apos; or a polymorphic transformation.&apos; The term "reactive hot pressing" has been coined to identify this process in which a phase change is combined with pressure to achieve interparticle bonding. This process is based on a principle which postulates that there is an enhanced reactivity and mobility of the molecular species at the phase-transformation temperature and this effect is utilized for interparticle bonding in powder compacts. This note summarizes the results obtained in an attempt to utilize this technique to produce ceramic-metal composites. In this case, a decomposition reaction of a compound (which after decomposition yielded an oxide) was used to achieve interparticle bonding in ceramic-metal composites. The reactive hot pressing was carried out in a Phillips induction heating unit, using either a graphite or a high-temperature steel die which functioned as both the susceptor and the hot-pressing component. The die was heated to the desired temperature in a helium atmosphere. All cermets produced by this technique were based on alumina as the ceramic phase. Different metal phases such as iron, copper, and chromium were used to study the effect of varying the metal phase on the properties of the composite. a Mono-hydrate (Boehmite) was mixed with different proportions of metal powders (-325 mesh) in dry condition in a mortar and pestle. No special precautions were taken for proper mixing. The mixtures were then compacted into a cylindrical form having an approximate dimension of 1 cm in diameter and 1 cm in height. For this compaction an ordinary

Jan 1, 1965

Paper withdrawn from publication September 8,1977, after book was printed. Pages 258.272 are therefore omitted.

Jan 1, 1977

By C. W. Mac Gregor

THE observation of the flow layers, or Lüders&apos; lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-steel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are in reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45° to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ner, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45° to the principal stress direc-tions at the point. As examples of the latter may be mentioned the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subjected to internal pressure only, etc. Hence if the flow layers are observed from an experiment, the shear-stress trajectories -the curves indicating the directions of the maximum shearing stresses in the body-may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45° to the principal stress directions, the family of principal stress trajectories, or the curves indicating the directions of the principal stresses, may be thus obtained. Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowan;1 in duralumin and other aluminum alloys, by Dawidenkow, 2 Elm,3 Fell, and others; in copper and copper-alloy crystals, by Elam;5 in brass by Elam;5 in brass wires by deForest;6 in higher carbon steels, tungsten steel, and

Jan 1, 1939

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

By Russell W. Dayton

The metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger,"&apos; i in 1909, was the first to apply polarized light to the microscopic study of opaque substances; Endell and Hanemann(2) were the next, in 1913. In 1919 and 1920, Wright(3,4) prepared two papers on the subject. In the first he developed the detailed mathematical theory from the viewpoint of the electromagnetic theory of light, and in the second described the various methods in use, giving improvements of his own. Schwarz(5)

Jan 1, 1935

By Russell W. Dayton

The metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger,"&apos; i in 1909, was the first to apply polarized light to the microscopic study of opaque substances; Endell and Hanemann(2) were the next, in 1913. In 1919 and 1920, Wright(3,4) prepared two papers on the subject. In the first he developed the detailed mathematical theory from the viewpoint of the electromagnetic theory of light, and in the second described the various methods in use, giving improvements of his own. Schwarz(5)

Jan 1, 1935

By W. L. Saunders

It is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance ; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel mas the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 niiles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world&apos;s record has been beaten by a single day&apos;s record in one heading of 36 ft. and by an average daily record in one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of Prance to the frontier of Hungary, betveen Italy and the plains of sonthern Germany. The contour

Jan 1, 1912

By V. N. Krivobok

THE study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency towards brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had little use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: ?. . . manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 per cent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper.

Jan 1, 1927

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934

By F. V. Shallcross

Physical properties of thin films of CdS and CdSe formed by vacuum deposition onto glass sibstrates have been studied as a function of deposition and processing conditions. The crystallinity and surface features of CdS films were examined using electron microscopy and electron and X-ray diffraction techniques. The films were poly crystalline; the preferred orientation and crystallite size increased with film thickness, substrate temperature, and deposition time. The CdS films consisted primarily of hexagonal-phase material, in contrast to similarly prepared CdSe films which have previously been observed to contain mixtures of cubic and hexagonal phases. As-deposited CdS films showed no major dependence of Hall mobility on crystallite size or degree of preferred orientation. Hall mobility and carrier concentration in CdS and CdSe .films were measured at various temperatures; both parameters increased with temperature and yielded activation energies which depended on fabrication conditions. Surface-desorption phenomena and overcoating of the semiconductor with SiO affected the observed electrical properties significantly. THIN films of cadmium sulfide1,2 and cadmium sele-nide3,4 have been employed by various workers as semiconductors in the insulated-gate thin-film field-effect transistor, known as the TFT. These devices are most commonly made by vacuum deposition of all materials onto an amorphous substrate such as glass. A knowledge of the microstructure and electrical properties of semiconductor layers used in the thin-film transistor is essential in order to form a realistic model for the device and to improve its performance, reproducibility, and reliability. This paper will describe studies of the physical properties of vacuum-deposited CdS and CdSe films prepared under various conditions. Structural characteristics examined in- cluded phases present, crystallite size, nature of preferred orientation of crystallites, surface roughness, and structural homogeneity throughout the film thickness. Electrical properties measured were Hall mobility and conductivity and their dependence on temperature and ambient. Thin-film properties are affected by many fabrication parameters including purity and physical form of evaporant, deposition rate, film thickness, design and temperature of the evaporation crucible, geometry of the deposition chamber, nature of the residual atmosphere, composition and temperature of the substrate, and details of postdeposition processing. PREPARATION OF FILMS In this work the semiconductor films were deposited in a conventional oil-diffusion-pumped system with pressures in the 10-8 torr range. The CdS evaporant was obtained from the Eagle-Picher Co. as a high-purity coarse-grained crystalline powder; the CdSe was a high-purity sintered powder supplied by the Harshaw Chemical Co. The evaporation crucible was a resistance-heated molybdenum-wire basket coated with aluminum oxide and filled with a quartz wool plug at the top. The source to substrate distance was usually 10 cm. This region was enclosed by a Pyrex inner cylinder. The substrate was heated with an overlying Pyrex plate coated with tin oxide. The substrate temperature was controlled using a thermocouple attached to the lower side of the heater. This thermocouple was calibrated against another thermocouple attached to a dummy substrate and by observation of melting points of various metal films deposited in the system. The substrates were polished borosilicate glass plates and conventional glass microscope slides. Substrate preparation included cleaning with an ultrasonically agitated detergent bath followed by isopropanol-vapor de-greasing. Film thickness was measured interferomet-rically during and after deposition. STRUCTURE OF CdS FILMS Structural studies were performed on CdS films using electron diffraction, electron microscopy, and

Jan 1, 1967