Search Documents

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By J. R. Long, R. S. Dean, F. S. Wartman, E. T. Hayes

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By W. N. Poundstone, G. R. Spindler

A comprehensive report on extensive experimentation in degasification of the Pittsburgh Coal seam is presented. Detailed accounts of the procedures and results are given for permeability tests, vertical bore hole tests, measurement of gas flow from sealed drainage areas, horizontal rib hole tests, and water infusion tests. The removal of methane gas from coal seams in advance of mining is not a new idea with mining men—much attention has been given to the possibility for many years. In other parts of the world, a principal concern has been in the recovery and utilization of the gas and a number of successful projects have been developed in Europe and elsewhere. In this country, the principal motivation has been related to the safety aspect with some possible side benefits concerning costs and efficiency in mining as secondary objectives. To date, experimental work in this country has been largely or entirely exploratory to determine bed characteristics with respect to the liberation of combustible gases to investigate or establish the possibility of degasification in advance of mining and as an aid in projecting mine ventilation systems to provide for safe, effective and economical handling of combustible gases liberated during mining. With these objectives in mind, the School of Mines and Engineering Experiment Station at West Virginia University, in cooperation with the Christopher Coal Co. of Osage, W. Va., initiated some experimental work in May 1952 and the project has been more or less continuous since that time. The work has been centered entirely in mines of the cooperating company in Monongalia County, W. Va., and Greene County, Pa. LOCATION AND GENERAL CONDITIONS OF THE AREA The principal mining in the area involved is in the Pittsburgh coal seam which lies at the bottom of the Monongahela series of the Pennsylvanian. The Pittsburgh coal in the area is generally uniform in its structure and physical characteristics. The bed thickness averages about 7 to 8 ft and the coal has a characteristic blocky structure as the result of pronounced face cleats and definite, but somewhat less pronounced, butt cleavage. It is a medium volatile coal, averaging about 37 pct, and is marketed principally as a steam fuel and for metallurgical purposes. The Pittsburgh coal outcrops along the Monongahela River and dips gradually, but not uniformly, slightly north of west (about N75°W). The westward extensions of the bed, from the areas contiguous to the Monongahela River which have been heavily mined, constitute the principal reserves and are all well below drainage with the depth of cover increasing with the distance from the river. In general, with deeper cover, it may be expected that methane liberation will be more of a problem in future mining as compared to areas mined previously; therein lies the interest in possible de-gasification in advance of mining. Fig. 1 shows the Pittsburgh coal area in the vicinity of Morgantown in Monongalia County, W. Va., and Greene County, Pa., in which the experimental work discussed is located. Fig. 2 shows the contours on the Pittsburgh coal in the test area. It will be noted that the first two bore holes for the experiments were at the edge of a bench or terrace with considerable change in the gradient in the immediate vicinity of the test holes and that the same general condition applies to later test areas. Mining is intensively mechanized in the area and in the mines involved in the experimental work with corresponding rapid advance of working faces a typical characteristic. In the areas now mined the total methane liberation ranges from moderate to relatively heavy, but the actual face liberation is extremely variable and may range from practically

Jan 1, 1961

By Kenneth Seaver

It is rather gratifying that in the field of the manufacture of refractories, in which, as a whole, foreign practice has surpassed us, the United States stands pre-eminent in the making of silica brick. In some instances European manufacturers have refused point-blank to credit the possibility of making to such specifications as are Common with us, until the actual completed shapes were shipped for inspection. But both the manufacturer and consumer in foreign lands are now frankly learning from us, and benefiting by our advanced practice in this field, as is evidenced by the orders placed here and the efforts put forth abroad to come up to the standard of American-made material. In no metallurgical operation has the employment of silica brick spread with such leaps and bounds as in the building of plants for the carbonization of coal, particularly in the byproduct coke oven. Today, in practically all types of oven, the structure above the floor level (except the facings) is of silica, while in the recuperative and in some regenerative types, its use is extended to that portion of the oven below the floor as well. By reason of the fact that there are a number of classes of refractories of higher silica content than the usual so-called fire-clay brick, there is sometimes a misunderstanding as to the class of material referred to as "silica" brick. We here refer only to a brick having a silica content of 94 per cent. or more and made usually from quartzite rock with a small percentage of lime as a binder. The term "silica" brick is sometimes rather loosely applied to brick from highly siliceous clays, or to a quartzite refractory of mingled fire-clay and quartz rock; but such products are not considered in this discussion. : Materials The rock from which practically all high-grade silica brick are made is a true quartzite or metamorphosed sandstone, variously known as

Jan 1, 1916

By J. G. Morlet, A. R. Troiano, H. H. Johnson

Delayed failure in steel occurs by controlled initiation and growth of a crack. The incubation period for crack initiation was measured. Crack initiation and Propagation are controlled by interaction between hydrogen concentration and triaxial stress state. The incubation period results from stress-induced diffusion of hydrogen to the point of crack initiation. THIS paper describes the phenomenon of delayed failureland the kinetics of crack initiation and propagation in uniformly hydrogenated steel. The investigation was prompted by service failures of high-strength-steel components at applied stresses far below the conventional yield strength, after the part had successfully sustained equal or higher stresses for an extended time interval. This delayed failure phenomenon, often termed static fatigue, is associated1 with the presence of hydrogen. This is not surprising, since the voluminous literature on flaking and hydrogen embrit-tlement demonstrates that hydrogen may exert a potent embrittling influence. Flakes, or internal hairline cracks in alloy-steel forgings, are related to the presence of hydrogen retained from the steel-making process.2 On the other hand, embrit-tlement arises from hydrogen introduced during surface treatments such as acid pickling or electroplating. Laboratory delayed failures have been induced in notch specimens of 4340 steel by electrolytic charging of the specimen surface with hydrogen and subsequent static stressing.l,4,5 Static fatigue was observed over a wide range of applied stresses; however, failure did not occur below a critical applied stress, designated as the static fatigue limit. In this instance the extended time for failure resulted primarily from the macroscopic redistribution of hydrogen. A crack formed to the depth of the hydrogen enriched "case* upon loading; further crack growth naturally awaited diffusion of hydrogen into the material ahead of the crack. The crack-propagation rate was therefore controlled primarily by the macroscopic diffusion of hydrogen into the specimen interior during the test. Thus, in this instance static fatigue was associated with the movement of a gross concentration gradient. However, delayed failure in steel of uniform hydrogen concentration is of greater fundamental interest, as well as commercial significance. With a homogeneous hydrogen distribution a different mode of delayed failure might be expected. As the heterogeneous hydrogen distribution became more uniform,4,5 the initial crack-propagation rate decreased markedly and, in fact, what appeared to be an incubation period for crack initiation was observed. However, the macroscopic concentration gradient precluded an accurate evaluation of these observations. Although the existence of an incubation period, up to this time, has not been established definitely, it is not amiss to point out some implications of the concept. It is of interest in all hydrogen-induced embrittlement phenomena, such as flaking, delayed failure, and hydrogen embrittlement. Much discussion has centered around the possibility of an

Jan 1, 1959

By Robert Isaac Williams

The Questa mine is located in northern New Mexico on the western flank of the Sangre de Cristo Mountains about 75 miles north of Santa Fe and ranges in elevation from 6,800 to 10,000 ft. GEOLOGY The rocks of the area are Precambrian metamorphic rocks covered by Tertiary extrusive andesites and rhyolites and intruded by Tertiary granitic rocks. These Tertiary intrusives are localized in an east-west belt about 20 miles long and 2 miles wide, extending from Questa to Red River. The Questa orebody is associated with a north-trending aplite intrusive about 3/4 mile wide and 1 3/4 miles long. In the area of mineralization, the metasomatism of aplite has produced a mottled porphyritic rock. This hybrid rock has caused much of the controversy about the Questa mine intrusive. The orebody is essentially monomineralic and consists of numerous closely spaced molybdenite veins varying in thickness from ' 'paint" to 3 in. and occurring in both the andesites and the intrusive. In the intrusive the veins are often siliceous. Common alteration minerals associated with the molybdenite ore vary with the original composition of the rock. The alteration of the aplite has produced phenocrysts of orthoclase, albite, oligoclase and biotite; veins of quartz, orthoclase, and biotite; and graphic myrmekitic intergrowths of feldspars and quartz. In many places near the contact, the andesite is indistinguishable from the metasomatized aplite. The dominant alteration in andesite, however, is the development of fine-grained biotite with apatite, rutile, and sphene.

Jan 1, 1969

By Taylor Lyman, E. P. Klier

The structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davcnport and Bain.' Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etchingl acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can he formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypo-eutectoid steels. Mechanism OF Bainite Formation Davenport and Bainl considered the mechanism of bainite formation to consist of two steps—an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide palticles, (not lamellae), at a rate depending upon temperature In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipi. tation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By E. P. Klier, Taylor Lyman

The structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davcnport and Bain.' Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etchingl acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can he formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypo-eutectoid steels. Mechanism OF Bainite Formation Davenport and Bainl considered the mechanism of bainite formation to consist of two steps—an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide palticles, (not lamellae), at a rate depending upon temperature In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipi. tation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

By T. L. Joseph

THE invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.1 After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it. His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be encountered from oxidation of the iron. Mushet was not only an inventor but he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, arid he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 5, 1927

Abbey. Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St., New York, N. Y. '21 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abeel, George H., Jr., Cons. Min. Engr 12S1, S. Canon Dr., Beverly Hills, Cal. '18 4 -Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin.. Univ. of Pittsburgh. Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 650 S. Grand Ave., Los Angeles, Cal. '82 Abele. Louis T., Min, & Met. Engr., Supt., Texas Hill Mine Coulterville, Cal. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada '31 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kan. '20 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., Member, Geological Staff of Burmah Oil Co., Ltd., Nyaunghla, Upper Burma, India. '28 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho '27 Acker, E. O'C., Met 128 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Research Lab., International Nickel Co., Inc Bayonne, N: J. '24 Ackerman, George F., Engr., Real del Monte y Pachuca Min. Co., Apt. 3, Pachuca, Hgo., Mexico '29 *Acres. T. H.. Geol. Dept., Valuation & Pet. Engrg., Richfield Oil Co., 555 S. Flower St., Los Angeles, Cal. '29 Adachi, Jinzoo Address Wanted '88

Jan 1, 1934

By M. L. Fuller

DURING the last several years many papers have appeared dealing with the structure of highly polished metal surfaces. The awakening of interest in this subject is due to the applicability of the electron diffrac-tion technique to the study of surfaces. The original theory of Beilby1 considered the surface of polished metals as of the nature of a super-cooled liquid or a vitreous, amorphous solid. The electron diffraction effects from polished metals have been interpreted by many to be a direct experimental proof of the correctness of the Beilby theory. This inter-pretation has been strongly opposed by others, so that at the present time the subject is in an uncertain and controversial state. In the present paper new, and hitherto unpublished, electron diffrac-tion effects from polished zinc are described. These observations indicate that the polished surface of zinc is crystalline.

Jan 1, 1938

By M. C. Young

The Ozark Lead Company operating facilities are located in Reynolds County at the south end of the "New Lead Belt" of southeast Missouri. Development of this wholly owned subsidiary of Kennecott Copper Corporation started in May 1964, with a six foot diameter by 1250 foot deep steel lined shaft. A 20-foot diameter, 1480 foot deep, concrete lined production shaft was collared in March 1968. Production from the facilities began that month and has reached a present average of approximately 6000 tons per day. This paper describes the fully automatic system used to hoist the lead-zinc ore from a depth of 1420 feet to the surface crushing and concentrating facilities, as well as the man and materials hoisting system which allows the lowering of large equipment into the mine. MINING Galena, sphalerite and some copper minerals are found in several mineralized zones of the relatively flat lying dolomite of the "Bonneterre formation". The mineable ore zones vary from 10 feet to 110 feet thick, from 200 feet to 1200 feet wide, and several thousands of feet on strike. Two-boom diesel-hydraulic jumbos equipped with rotary percussion drills are used for both development and production. The jumbos are used principally to open the room and pillar stopes, and a track mounted down hole drill is used to bench in areas where the ore thickness warrants. Explosives used are ANFO, dynamite, and water-jell which are detonated by electric blasting caps. Broken ore (and waste) is hauled by rubber tired transports to chuted transfer raises. Approximately every 500 feet, these raises connect the orebody to the 15 foot by 28 foot train haulage level below. Two twenty ton diesel-hydraulic locomotives haul 160 tons per trip to storage pockets which have a total storage of 1500 tons of material. From these pockets the material is fed over a 6 foot by 20 foot mechanical vibrating feeder which includes one 4 foot by 6 foot grizzly section to a 48 inch by 60 inch jaw crusher. The grizzly and crusher products are transferred horizontally 45 feet on a 48 inch conveyor belt, to one of two 750 ton storage pockets. The material can flow unimpeded into one pocket or be deflected into the second pocket by a movable rock filled hopper. LOADING POCKET The material in each storage pocket is controlled by six lengths of ship anchor chain. The upper end of the 20 foot chain is anchored behind a brow in the pocket, while the lower ends are joined by a header. The lower ends of the chains are raised by two electric powered marine barge winches using 3/4 inch cables. The crusher operator controls the raising and lowering of these chains from a console in the crusher station. The upper and lower travel of the chains is controlled by cams and limit switches on the winch drive. The winches are located within 5 feet of the shaft, and shaft water continually causes problems with the electric components. A malfunction in the upper travel switch will cause the winch to pull the chains into the cable sheave (breaking the cable or sheave), while the lower switch causes the winch to unwind too much rope. Serious consideration is being given to changing the electric motors to pneumatic, since pneumatic motors will eliminate the need of any electrics at the winches. The winches can be "bottomed out" against the sheave without damage to the cable or sheave when raising the chains, and can be allowed to "free wheel" to lower the chains. A surge pocket below the two storage pockets feeds material to two

Jan 1, 1975

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

By H. P. Greenwald

THE Committee on Rock-Dusting was formed after the fall meeting of the Coal Division in Chicago in 1938. Its primary task was to study the recommended American practice for rock- dusting coal mines to prevent coal-dust explosions as approved by the American Engineering Standards Committee. After approximately two years' work he committee concluded that although certain portions of the recommended practice could well be revised, information needed for a logical revision was not at hand, and it was inadvisable, therefore, to make revisions

Jan 1, 1943

By A. U. Seybolt

Experiments on both suljidation and hot corrosion have been carried out using ternary Ni-Cr-X alloys and commercial nickel-base superalloys. It has been shown that lhere are certain micro structural similarities between sulfidation using H,S/H2 mixtures and hot corvosion using Na,S04 in "crucible" experiments or hot corrosion tests using a flame tunnel apparatus. It is proposed that two key processes in the hot cowosion process are: 1) formation of chromium sulfides which deplete the alloy matrix, and 2) oxidation which can be accelerated because of chromium depletion. Other processes play an important role in the hot corrosion process, such as accelerated oxidation attack due to the presence of a N& S04 or N&SO,- NaC2 film which inhibits the formation of a protective external oxide scale. However, this latter phenomenon was not studied in this work. THE term hot corrosion has come to mean a combination of sulfur and oxygen attack on nickel-base or cobalt-base superalloys used as gas turbine blades or partitions. This attack can be initiated by any combustion process in air involving fuel containing sulfur if the sulfur level is sufficiently high. Levels of 5 pet SO2l for example, in the combusting gas have been observed to produce hot corrosion attack on nickel-base alloys. The important immediate corroding medium in aircraft gas turbines, however, has been established to be Na2S04, formed from reaction between NaCl from sea air and sulfur in the fuel.' The Na2S04 concentrates the sulfur sufficiently so that superalloy parts heated in the range 1400" to 1900°F can become sulfided by reducing the Na2S04 film which forms on the parts, and this reaction allows sulfur to gain access to the alloy. The sulfur thus released diffuses into the superalloy and forms primarily chromium sulfides of various compositions, but frequently Cr2S, has been identified. Figs. 1 and 2 show the morphology typical of hot corrosion of a cobalt-base superalloy X-45 (25 Cr, 10 Ni, 7.5 W, 0.25 C) and a nickel-base alloy, Udimet 500 (19 Cr, 19 Co, 4 Mo, 3 Ti, 2.9 Al, 0.07 C). Both alloy samples were subjected to the same hot corrosion conditions: 616 hr at 1600°F in a combusted 2.9 pct S distillate oil containing 125 ppm Na as NaC1. It will be noted at once that the nickel-base alloy is much more severely attacked. The depth of corrosion is much greater and the number and size of the sulfides present are much greater. Both alloys show a duplex oxide scale, which is more noticeable in the X-45 alloy. The external scale is probably a spinel in both cases, with CrQ3 lying next to the alloy. Many investigators1 -"ve been concerned with hot corrosion phenomena, but there has been a lack of unanimity of opinion as to the details of the hot corrosion mechanism. More than one definition of hot corrosion is possible. Some investigators con- sider as a measure of hot corrosion only the weight gain due to an accelerated oxidation. However another point of view is that the total depth of affected alloy may be used as a measure. While it is recognized that surface oxidation attack is greatly accelerated by the presence of salts like Na2S04 or Na2S04-NaC1 mixtures, sulfur penetration into the alloy also undoubtedly produces very important effects. The region of sul-fide penetration which is so prominent in Fig. 2 is one of the outstanding characteristics of hot corrosion. For highly stressed parts, such as first-stage buckets, this sulfur-penetrated region can be more significant in mechanical property loss than the reduction of cross section produced by the formation of the massive external scale. In addition, evidence will be presented that this sulfided region can be less resistant to subsequent oxidation attack. Since it appears that the sulfided region below the surface oxide scale plays an important role in the overall corrosion process,

Jan 1, 1969

By J. J. Beeson

Page I. PrimaRy MineRalization............................................ 356 1. Introduction..................................................... 356 a. Scope of Work............................................... 356 6. Acknowledgments............................................ 357 c. The Bingham Mining District.................................. 357 d. General Geology.............................................. 357 e. The Utah Copper Mine....................................... 376 f. Field and Laboratory work.................................... 376 2. The Quartz-Monzonite.............................................. 377 3. The Pegmatite Veins.....:.•..............................:........ 378 4. The High-Temperiture Veins.........................-.............:379 5. The Early Hydrotherma! Period.:......................'............ 380 6. The Late Hydrothermal Period................................:.... 385 II. Seconuabx EnricuMENT............................................. 386 . 1. Author's Note;..... ;............................................ 386 2. Factors Governing Enrichment.....................................: 387 3. The Enrichment.................................................... 387 4. The Covellite Enrichment.; .:; ; : .:. :..:.............:................ 388 a. The Capping above the Covellite Ores:....:....................... 388 b. Conclusions Drawn. from a Study of the Capping and the Covellite ; Ores....,.............................................:.....,.' 392 c. Covellite Enrichment at Depth......:......................... : : 392 5. The Chalcocite Enrichment...................................... ; 394 a. The Carbonates in the Capping above .the Chalcocite Ores...:..: .. 394 ' b. The Formation of Chalcocite..:.:. :......:..'...........,......' 394 . 6. Secondary Chalcopyrite and Bornite.............................i ..., . 395 111.- Conclusions as to the Formation.oF the ImpoRtant Sulphides in the Disseminated ORes........................................,.......... 400 I. Primary MiNeRalization 1. Intrdtiction a. Scop. e .of Work.. first part bf, this paper deals with the country rock, its pegihatitic, pneumatolytic', and hydrothermal altektions; also, the effect of magnetite on the deposition of the primary chalcopyrite and pyrite.

Jan 1, 1916

By E. J. Rapperport, M. F. Smith

A presentation of the W-Ru constitution diagram is given. Techniques utilized in the determination of phase boundary values include electron micro-probe analysis of two-phased alloys and diffusion couples, as well as normal metallographic and X-ray methods. The primary features of the diagram are: 1) a terminal solid solution of ruthenium in tungsten with a maximum solubility of 23 at. pct Ru at 2300°C; 2) a terminal solid solution of tungsten in ruthenium with a maximum solubility of 48 at. pct W at 2205°C; 3) a o phase of maximum breadth about 6 at. pct based on the composition W3Ru2 which forms peritectically from the melt at 2300°C, and which decomposes eutectoidally at 1667 °C to form a twigs ten and 0 ruthenium; 4) a eutectic at 45 at. pct Ru and 2205°C with the products being o plus ß ruthenium. THE W-Ru diagram has previously been studied only in a cursory fashion. Raub and alter' obtained a 1400°C isotherm in which they observed no intermediate phases, and on which they established the limits of solubility as 36.5 at. pct W in ruthenium and about 1.5 at. pct Ru in tungsten. In addition, Obrowski2 found a o phase forming peritectically from the melt and existing only above 1650°C. Below this temperature the phase was presumed to decompose eutectoidally. The present work finds the diagram as given in Fig. 1. I) EXPERIMENTAL PROCEDURE The materials used for alloy preparation in determining the W-Ru constitution diagram were 99.9 pct pure ruthenium powder supplied by Baker Chemical Co., and 99.9 pct pure tungsten powder from General Electric Co. Typical analyses of these elements are given in Table I. Initial alloys at 10 at. pct intervals were prepared from the metal powders by the following method. Powders sufficient for 25 g of the alloys were weighed out with an accuracy of 0.1 mg and blended mechanically. After blending, the powders were compacted, in a steel die, at approximately 30,000 psi. The compacts were sintered in an electric vacuum furnace in order to remove adsorbed gases and to achieve partial densification prior to arc-melting. Vacua of 10-4 mm Hg or less were maintained in sintering as the furnace temperature was raised to approximately 2000°C. Sintering times ranged from 10 to 20 hr. The sintered compacts were arc-melted under a protective atmosphere of purified helium. Melting was conducted on a water-cooled copper hearth, utilizing a nonconsumable tungsten electrode. In the melting process, each alloy was turned over and re-melted on opposite sides from four to six times to ensure complete melting and to eliminate gross in-homogeneities. The arc-melter used had a vacuum capability of 5 X 10-6 mm Hg, and a leak rate of about 20 -liters per hr. Chemical analysis techniques for refractory metal-platinum group metal combinations are not well-established; therefore, composition control and determination depended principally upon weight-loss observations and calculations. This consisted in weighing each alloy after sintering and after arc-melting, and calculating the maximum and minimum composition values, assuming the total weight losses to be first all tungsten, and then all ruthenium. Since composition uncertainty was directly related to weight loss, care was taken to minimize losses in handling, compacting, and melting. Prior to homogenization and equilibration the as-arc-melted alloys were analyzed in several

Jan 1, 1964

By C. L. Kinney

The rapid increase in the amount of steel produced by the basic open-hearth process is an index of its ability to produce high-grade steel from raw materials of the most, varied physical character and chemical analysis. This inherent adaptability of the process has resulted in a lack of care in the selection of raw materials, so that in far too many cases charges are used of a chemical and physical character not justified by local economic conditions. A practice, or series of practices, should be used that will result in the greatest economy for the plant as a whole; therefore, the operations of blast furnace and open hearth must be considered together. In this paper, an effort has been made to show those variations in both open-hearth practice and cost that follow changes in the analysis of the pig iron arid it may be said that the theoretical costs shown are worthy of careful study and consideration. Carbon, manganese, silicon, phosphorus, and sulfur constitute the principal metalloids in basic pig iron and play the leading role in the production of steel by the basic open-hearth process. The percentages of each of these metalloids, with the exception of carbon, is a variable that has its genesis in the economic relation of the blast-furnace plant to its ore and fuel supplies. As the amount of carbon in the iron is a saturation function of the temperature at which it is produced, the variation in the amount carried is, for any given locality and grade of iron, practically negligible and is so considered in the eight heats discussed in this paper. The melting and refining reactions in an open-hearth furnace, either acid or basic, are essentially oxidizing and vary greatly with the type and age of the furnace, as well as the character of the fuel employed. The outstanding characteristic of the basic process, and the one that explains its predominance over the acid, is its ability to form out of the lime charged and the phosphorus oxidized from the charge a stable

Jan 1, 1924