Search Documents

By H. S. Munroe

THE native copper of Lake Superior occurs in the form of fine grains and scales, disseminated in small percentage through the copper-bearing rock ; and in large and small masses, from a few pounds to several hundred tons in weight. Formerly the bulk of the copper came from the mines of Ontonagon and Keweenaw counties, producing mass copper. At present these mines furnish less than one-tenth of the total product, and fully one-half of this is from a single mine. The masses are usually found irregularly distributed in nearly vertical fissure veins, and require much dead work in sinking, drifting, and stoping for their development. The risk and expense attending the working of these mines have made them, with few exceptions, anything but profitable. * Read at the Montreal meeting, September, 1880.

Jan 1, 1880

New Jersey Zinc Co. - The Plants Canon City Palmerton Depue

Jan 12, 1953

By D. J. Mack, R. E. Reiswig

Six examples of the peritectoid transformation were selected from the literature and studied by the method of isothermal transformation. The kinetics and mechanisms of five of the examples are presented as TTT diagrams and photomicrographs. The exist-enc- of a peritectoid in the sixth case is doubtful. ALTHOUGH the peritectoid transformation per se has been known for many years, no precise published data exist concerning the kinetics or mechanisms involved in transformations of this type, except for the brief treatment by Rhines, et al. 1,10 Bearing in mind the fact that investigations of recent years are uncovering more and more peritectoids and suspected peritectoids, a thorough study of the well-established peritectoids appeared to be in order. It was for this reason that a study of the kinetics and morphological mechanisms of six binary peritectoids was undertaken. The six peritectoids selected from the literature for study were those reported at 7.02 wt pct Al-Ag, 26.0 wt pct Sb-Cu, 30.5 wt pct Sb-Cu, 32.3 wt pct Sn-Cu, 8.35 wt pct Si-Cu, and 21.2 wt pct Al-Cu. These selections were based on availability and purity of components, ease of preparation and heat-treatment, and estimated reliability of the available equilibrium diagrams in the regions of interest. EXPERIMENTAL PROCEDURE The alloys used in this investigation were induction melted in electrode-grade graphite and chill-cast in cast-iron split molds. In all cases, the alloys were so brittle that they could easily be broken into samples weighing 1 or 2 g. Chemical analyses showed that the alloys used were close to the respective peritectoid compositions reported in the literature and that the impurity levels were low in all cases. Metallographic examination showed uniform distributions of phases in all samples, indicating uniformity of composition in the samples studied. Isothermal transformation studies were carried out in fused-salt media, using the familiar inter-rupted-quench method. Uniformity of temperature in the salt baths was maintained by continuous stirring with a stainless-steel agitator. On the basis of actual observations of the temperature fluctuations, the estimated temperature control was + 10C for the Ag-Al and Cu-Sb alloys and ±30C for the Cu-Sn, Cu-Si, and Cu-Al alloys. The accuracy of all temperature measurements was estimated to be ±1°C. It was found necessary to mount metallographic specimens of the Ag-Al alloy in cold-curing methyl methacrylate, since the temperatures encountered in mounting in bakelite or lucite caused an appreciable degree of transformation to the ß phase. For the other alloys, wood-flour-filled bakelite mounts were used to avoid extraneous X-ray diffraction lines during the later examination of the metallographic specimens on a Norelco Geiger-counter d if f r ac tomete r. In the X-ray diffraction procedure, agreement between the published diffraction patterns and those obtained in this study was good. This was particularly important for phase identification, since the literature contained little in the way of micrograph description in some cases. Etching of the silver-aluminum alloy for metallographic examination was done by swabbing with either of the following reagents: 1) 10 g CrO3, 1 g (NH4), SO2, 0.5 g NH4NO3, 100 ml H2O, or 2) 10 ml NH4OH, 1 ml 20 pct KOH, 4 ml 3 pct H2O2, 5 ml H2O. The other alloys were etched with the usual bichromate etchant: 2 g K2Cr2O7, 1.5 g NaC1, 8 ml conc. H2SO4, 100 ml H20 (swabbed vigorously). EXPERIMENTAL RESULTS A) The Ag-Al peritectoid at 7.02 wt pct Al— The phase equilibrium involved in this peritectoid is shown in Fig. I.2 The phase boundaries in the vicinity of the peritectoid were most comprehensively established by Hume-Rothery, et al,3 who placed the equilibrium temperature at 448 °C and the equilibrium compositions of the a ß' and y phases at 6.11, 7.02, and 7.24 wt pct Al, respective The alloy used in this study analyzed4 6.95 wt pct A making it slightly hypoperitectoid according to the accepted equilibrium diagram. The rate of the transformation a+ y — ß' varies rapidly with degree of undercooling below the equilibrium temperature, passing through a maximum in the vicinity of 350°C. Thus the TTT dia-

Jan 1, 1960

By R. H. Frazier, J. M. Hodge, F. W. Boulger

This paper reports the results of studies of the impact properties of quenched and tempered alloy-steel plates as a function of sulfur content. It was found that the impact energy levels decreased continuously as the sulfur content increased and that there was a straight-line relationship between impact energy and sulfur content when plotted on logarithmic coordinates. Cross rolling raised the level of these Lines for transverse tests and lowered the level for logitudinal tests proportionately to the amount of cross rolling. ALTHOUGH it has been generally recognized that, for applications in which notch toughness is critical, the sulfur content of the steels used should be held to a low value, quantitative information on the effect of sulfur on notch toughness has not been available. For such applications, it is a common practice to specify minimum impact values, and in order that these may be met consistently it is important that the steel producer know quantitatively the effect of sulfur on notch toughness so that realistic sulfur content limits can be applied to the steels they produce. In many instances, particularly in flat-rolled products, impact properties are specified in the direction transverse to the principal rolling direction, so that the factors affecting the anisotropy or directionality of impact properties are also of concern to the steel producer. For some applications, furthermore, it is a common practice to increase the sulfur content of steels in order to improve their machinability, and, in such instances, the effect of this practice on notch toughness may often be of concern. This paper reports on an investigation, carried out at Battelle Memorial Institute, designed to furnish this quantitative information on the effect of sulfur on notch toughness and also to furnish further information on the factors affecting the anisotropy of impact properties in wrought heat-treated alloy steels. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental steels were of intended base analysis: 0.30 pct C, 0.80 pct Mn, 0.25 pct Si, 2.5 pct Ni, 0.80 pct Cr, and 0.45 pct Mo. Steels were made with sulfur contents varying from 0.005 to 0.179 pct. The steels were prepared from 600-lb induction-furnace melts. Steels containing 0.020 pct or more sulfur (at meltdown) were melted from a charge of ingot iron (except for one heat): lower-sulfur steels were made from electrolytic iron. The charge consisted of ingot or electrolytic iron, ferrosilicon to give 0.10 pct Si, and ferromanganese to give 0.05 pct Mn. At meltdown, electrolytic nickel, ferromolybdenum, iron phosphide, and pyrite were added followed in sequence by ferrochromium, sili-comanganese, ferrosilicon, and ferromanganese. The slag was then removed and graphite added to give the desired carbon content. Bath temperature was adjusted to 2850°F and, when no other additions were to follow, 2 lb per ton of aluminum was added, immediately before tapping. Compositions of the experimental steels appear in Table I. Analyses are from single determinations, except sulfur which was analyzed in duplicate. A test sample (3 in. in diam by 6 in. long) and a 575-1b ingot were poured from each heat. The test sample was poured in a sand mold; the cooling rates of the test sample and the large ingot were approximately the same. Chemical analysis chips and metal lographic specimens were taken from the test samples. The ingot was 8 in. sq at the base and 9 in. sq at the top. A 5 X 5 X 6-in. sand mold hot top was completely filled in teeming the ingot. After solidification, the mold was stripped from the ingot which cooled to room temperature. Ingots were reheated to 2250"F and rolled to 1.9-in. slabs on a commercial mill. The slabs were box-cooled to room temperature. Sections of the 1.9-in. slabs were heated to 2250°F and rolled on a Battelle laboratory mill according to one of three schedules: 1) rolled straightaway to 0.5-in. plate; 2) rolled straightaway to 1.3-in. thickness, then cross rolled to 0.5-in. plate (29 pct cross rolling); or 3) cross rolled from 1.9-in. to 0.5-in.-thick plate (46 pct cross rolling). The 0.5-in.-straight- or cross-rolled plates were normalized at 1700°F for 1 hr and then water quenched from 1600°F. Plates were then tempered 2 hr at 1240°, 1170°, 1080°, or 860°F to obtain Rockwell C hardness of 25, 30, 35, and 40, respectively. Tempering was followed by quenching to room temperature to avoid temper embrittlement. Slack-quenched plates were isothermally transformed for 26 min at 800°F, quenched, and tempered 2 hr at 1170°F. Pearlitic microstructures were obtained by holding 168 hr at 1200° F, followed by quenching. Charpy V-notch specimens were taken both transverse and longitudinal to the main rolling direction, notched perpendicular to the plate surface, and tested. Slabs and plates which were to be homogenized

Jan 1, 1960

By John A. Ames

Webster's dictionary nearly equates portland cement with its current primary definition of cement. While such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to "varieties" of portland cement including "portland-pozzolan" cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far corners of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry between 1756 and 1972 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. As part of the 4th edition of Industrial Minerals and Rocks, this chapter on utilization focuses on inferred interests of the anticipated readers. The main period for which statistics are cited generally is that since the 3rd edition (1960) of this same volume. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or "burning") step, which brings about the necessary changes in the raw materials. This pyro processing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The U.S. Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relate to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. The year 1972 witnessed a test of the adaptability of cement industry statistics. This was the year of conversion from barrels and sacks of cement as the units of measure to tons and hundredweights. The barrels and sacks related to volumetric measures in that a sack was judged to be 1 cu ft (weighing a "standard" 94 lb). A barrel was 4 sacks. Volumes of concrete are stated in cubic yards, and the number of cubic feet of cement in a cubic yard of concrete was a sensible approach to the mensuration involved. However, cements do not weigh the same amount from plant to plant or from type to type, and the buyer was more interested in getting an assured weight for his money than in "buying air." Thus, a sack, in accepted practice, became 94 lb instead of 1 cu ft, and a "barrel" became 376 lb, regard- less of whether it would fit into 4 cu ft of space. With the de facto dealing in weight rather than in volumes, the awkward numbers made little

Jan 1, 1975

DISCUSSION, M. Cohen presiding A. H. Geisler and D. L. Martin (GeneTal Electric Research Laboratory, Schenectady, N. Y.)—We were rather interested to note the author's conclusion that the cubic to tetragonal transformation may be of the second order, for we have been able to show that the order-disorder transformation in an analogous alloy system is a first-order transformation with a discon-

Jan 1, 1952

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS, * LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By Henry E. Wood

In my opinion, the concentration of minerals by flotation is the most interesting problem in ore-dressing, and will command eventually far more consideration than it has at present. For many ores it furnishes a complete method of concentration absolutely independent of specific gravity, and thus simplifies the milling of many difficult combinations. Not having to recognize the influence of specific gravity, we are also able to dispense with some of the complications resulting from classifying-conditions. Where flotation cannot be used for a complete separation of the minerals from the gangue, it will be found, in nearly all cases, to save those portions which are generally lost by reason of their fine state of division. For this reason, it should be looked upon mainly as an aid to general concentration, although there are many ores so well adapted to flotation that more than 90 per cent. of the valuable metals can be recovered from them in one operation by this process. In presenting the results of my investigations in flotation, I have endeavored to theorize as little as possible. That side of the subject has been extensively discussed by others. My earliest work with flotation was done in 1895, when I used various oils, grease, soap, etc., with results that were remarkable. I did not realize then that with water alone equally good separations could be made. Up to 1906, my endeavors were confined to attempts to keep the concentrates on the tables well wetted and away from exposure to the air. In common with others, I observed that when there mas any obstruction in the wash-water on the table of sufficient size to divert the water to either side, the concentrates collected, and, on exposure to the air, would promptly float away. This convinced me that the sulphides were all good "swimmers," and that if,

Jan 1, 1913

By Larry Kaufman, Morris Cohen

THE solid phase equilibria' and the martensitic transformation in the iron-nickel system have been the subject of considerable study. In addition, there have been numerous investigations on the calorimetric and thermodynamic properties of iron-nickel alloys. The purpose of the present work is to extend the existing information concerning the martensitic reaction in the iron-nickel system, and to develop a general thermodynamic treatment which will encompass the equilibrium and non-equilibrium phase

Jan 1, 1957

By L. B. McConville

The general term "tar sand" refers to sand that contains varying amounts of dense, viscous petroleum. Tar sand deposits have been found throughout the world, often in the same geographical area as conventional petroleum. The largest one by far is known as the Athabasca Tar Sands, in the province of Alberta, Canada. Actually a group of three deposits, these particular sands underlie an aggregate area of more than 12,000 sq miles. Current estimates place the contained raw petroleum at about 700 billion bbl; and via currently available technology, the amount of recoverable synthetic oil may be as much as 300 billion bbl-which is roughly equivalent to five times the combined US and Canadian total crude oil reserves. With the ever-widening gap between energy supply and demand, mining and petroleum companies are now evaluating all possible energy resources-both developed and underdeveloped-and, certainly, the Athabasca Tar Sand deposit is one of the more important ones to merit such attention. The first section in ME deals with the geology and historical developments; the other four sections, with mining methods, extraction technology, economics, and outlook.

Jan 1, 1975

By J. B. Goddard

Crystallization of ammonium paratungstate (APT) is frequently the last effective purification step in producing high-purity tungsten. However, crystallizer mother liquors are often several times higher in tungsten than predicted by the solubility of APT. The formation of heteropoly anions, particularly those containing phosphorus and silicon, is largely responsible. Solubility of tungsten in APT mother liquor can be linearly correlated with the concentration of these and other impurities. The problem can be overcome by direct treatment of the crystallizer feed solution with aluminum sulfate. By appropriate treatment, the aluminum hydroxide flocculates and is easily filtered, resulting in a purified low-aluminum crystallizer feed from which high APT yields can be attained.

Jan 1, 1985

By T. A. Rickard

The earlier paper (Trans., xx., 463) describing this Victorian mining district, to which the present is supplementary, was mainly confined to the consideration of the "saddle-reefs," as scientifically the most interesting and economically the most important of the

Jan 1, 1893

By J. L. Wyatt

The electrical resistance of titanium as a function of purity and temperature was measured from —325" to 2800°F. Two points of inflection in the data plots were found, and an increase in resistance with increase in temperature above the transformation was observed. IN 1948 Greiner and Ellis' reported on the thermal and electrical properties of titanium, including a study of the effect of temperature on the electrical resistance. The materials used in the research were obtained from the United States Bureau of Mines, where powder metallurgy techniques were being employed for consolidation purposes. These authors found a decreasing resistance with increasing temperature above 1625°F, and concluded that the latter temperature represented the point of transformation from hexagonal close-packed to body-centered cubic structure on heating. They reported a specific resistivity value of 55x10-6 ohm-cm, and showed that dp/dt was positive, decreasing with increasing temperature above ambient. In one of his early texts Hume-Rothery2 mentioned that certain metals, including titanium, exhibited minima in plots of resistance vs temperature. He indicated that this occurred at 212°F. Reporting many years ago on the effect of temperature on the electrical resistance of zirconium, de Boer and Fast³ showed that phase transformation in this sister metal occurred over a range of temperatures, the extent varying with its purity. Graphs of resistance vs temperature, showing transformation effects over a range of several hundred degrees, were presented for relatively impure metal. In the latter case the resistance decreased with increasing temperature throughout the region of partial phase transformation, thereafter increasing as predicted for normal metals by modern theories of the solid state. Since the quality of metal used in previous studies was substandard compared with iodide-type titanium, and in view of the fact that there seemed to be some rather unusual observations in the reported literature, it was decided to undertake a more extensive study of the thermal effects using high purity titanium, and to include temperature ranges beyond those which had been studied in order to ascertain whether or not the characteristics of zirconium would be duplicated. Experimental Materials Materials used in this investigation included commercial quality titanium (Ti-75A produced by the Titanium Metals Corp. of America) in the form of ¼ in. diam rods, and high purity iodide titanium (produced by the Foote Mineral Co.) in the form of crystal bar of irregular size. The latter was cold-swaged into rod form and machined to the desired size. Lead wires to all specimens consisted of 18 gage Ti-75A. Chemical analyses of the stock materials are given in Table I. Experimental Procedures Specimens 2½ to 3 in. in length were prepared with diameters nominally 0.15 to 0.20 in. Two holes,

Jan 1, 1954

By Harold Roast

THE object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4. Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests. 8. Brinell tests, at temperatures from 80° to 400° F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: LEAD, ANTIMONY, TIN, COPPER, ARSENIC, NUMBER PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.94 59.87 2.65 none 3 77.65 20.75 none 0.13 1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sulfuric acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thiocyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference.

Jan 2, 1922

By S. S. Clarke

LATE in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls Were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1947

By Arne Westgren

ONLY in exceptional cases can the ordinary methods of chemistry be used for determining the constitution of compound metallic substances. Recourse has therefore been taken to special methods, the main expedients of which are, as we know, thermal analysis and metal microscopy. To these may be added-though more accessory-the determination of electric conductivity, specific volume, hardness or other properties. The information obtained by these methods has been compiled in equilibrium diagrams. Naturally, the technically most important alloys, such as steel, bronze and some others, have been subjected to very close study, and many investigators have devoted themselves to the solving of their problems of constitution. The equilibrium diagrams of these systems are therefore known today with a comparatively high degree of accuracy, even though it must be admitted that many details regarding their transformation reactions still remain to be completely explained. The equilibrium diagrams of the other alloys as a rule have not been determined so accurately. Most of them are based only on approximate determinations of the homogeneity ranges of the various phases. Thus extensive, detailed studies remain before these diagrams may be considered as established. Unfortunately, it must also be admitted that many of the alloy diagrams given in the present handbooks are as a whole very dubious. As a matter of fact, many of them may really only be viewed as the results of rather superficial, orientating investigations. In fact, there also seems to be a general opinion prevailing in our day that much work still remains to be done before the equilibrium conditions of the alloys may be considered as fully explained. At present, in almost all institutes for research on metals, as well as in many university laboratories, investigations to this effect are being carried out. As a rule, the classical methods of metallography, the thermal analysis and metal microscopy are applied.

Jan 1, 1931

By William J. Gillich, Gerald L. Moss

PREVIOUS studies of the shock loading of randomly oriented polycrystalline aggregates have firmly established that, after rather short load duration, hydrostatic compression closely approximates the shocked state.' However, McQueen deduced from pressure measurements with good time resolution that, during shock loading, metals begin to undergo a stress relaxation at the yield stress. He suggested that the relaxation is due to plastic deformation accompanying the change from a one-dimensional compression to a three-dimensional, hydrostatic, compression.' Stress relaxation may occur faster as stress is increased above the yield stress, but the existence of unidirectionally compressed states for finite times suggests that the concept of a unidirectionally distorted lattice should furnish considerable insight into the mechanical behavior of materials subjected to shock loading. Here, a crystallographic analysis is presented for the hypothetical situation where atom motion may be considered as unidirectional which, as indicated above, is a useful extension of the macroscopic concept of shock loading to the microscopic domain. Only motion caused by the com-pressive forces is treated; i.e., lattice vibrations upon which this motion is superimposed, as discussed by Fitzgerald, are ignored.3 The purpose of the analysis to be presented is to develop a description for single crystals of the lattice rotations that occur for idealized uniaxial strain deformation. The usefulness of such an analysis in realistic deformation is to give a method of specification of those properties of an initially distorted lattice which would affect the subsequent deformation. Non-axial complications that arise experimentally, such as off-axis rarefaction waves, must be treated in proper context. Consider the material element shown in Fig. 1 and let the compression be uniform at all regions of the element. Then, any interior point of the element is displaced in proportion to its distance from the base of the element. Accordingly, if the top of a unit element is displaced by an amount, (-K), with respect to the base, a point P(X, Y) will be displaced by (-KY). Crystal planes are, therefore, rotated by the compression. Analysis of this rotation may be accomplished from the geometry shown in Fig. 1 where the line OP is the edge of the plane {hkl} and N is its normal. The orientation of the crystal plane with respect to the shock direction is specified by the angle, before deformation. After deformation the edge of plane {hkl}

Jan 1, 1969

By J. F. Emig

The Burns Harbor Plant was designed to produce and process large ingots into plate, hot rolled sheet, cold rolled sheet and tin plate. Rimmed ingots, in particular, are poured 96" to 106" high and weigh up to 85,000 lbs. During the latter part of 1970, a quality problem was encountered involving white line "sliver" defects on the surface of cold rolled, low carbon, rimmed steel sheet. Sheets containing these defects are not desirable for exposed automotive items because of the possibility of opening during forming or becoming more apparent after forming. Metallographic work located and identified two basic types of inclusions within the white line defects: (1) complex oxides consisting largely of iron and manganese oxides and (2) scale-type iron oxide. The presence of these oxides strongly suggested that the-white line defects were resulting from an unsound, unclean rim zone.

Jan 1, 1972

VARYING in thickness and in number from place to place, coal seams in the Canadian Rockies also range in pitch from nearly horizontal to vertical, sometimes with overturns. Over the entire coal-bearing area there are considerable differences of rank in coals of the same geological age, and there are marked differences in ash content and washability characteristics. Correlation of seams at mining operations within a few miles of each other has often proved impossible. These factors influence mining methods, and, of course, production results. The oldest coal formations of western Canada are of Lower Cretaceous age, as the carboniferous sediments are marine and contain no coal. Coal is also present in formations of Upper Cretaceous and Tertiary ages. The rank of coal varies from semianthracite in some operations in the Kootenay and Luscar formations of the Lower Cretaceous in the Rockies to lignite in the Tertiary fields of the Saskatchewan prairies. Fig. 1 shows the general extent of the formations.

Jan 8, 1954

By Leroy U. Gardner

EVERY reader of this paper is well aware of the fact that the prolonged inhalation of large amounts of free silica dust results in fibrosis of the lungs, and that other inorganic dusts, except those of asbestos and the mineral poisons, are thought to be relatively harmless. But probably few have had opportunity to visualize the effects of silica, asbestos and other minerals upon living tissues. The ideal demonstration would be based upon sections of lungs from human beings that had inhaled com- parable concentrations of different dusts for a unit period of time. Such material is generally difficult to obtain and in some instances is of questionable value because the subject has been exposed to more than one kind of dust. A demonstration could be prepared from the lungs of animals. However, so many months or even years are required to complete the exposure to each kind of dust that enough material has not been accumulated. For a general survey of the action of different types of dust, I am therefore compelled to use the tissues of animals that have been injected with suspensions of dust particles. The injection method offers certain advantages. The quantity, the particle size and the state of dispersion can be controlled with sufficient accuracy so that the tissue responses to different minerals can be accurately compared. The method insures contact between the tissues and the mineral particles; protective mechanisms, which may prevent the inhalation of certain types of foreign body, never come into play. If the pathway of injection be one that minimizes nonspecific injury, the tissue responses may simulate those produced by inhalation but they develop somewhat more rapidly. It should always be remembered that injection methods merely demonstrate the capacity of various kinds of minerals to provoke reaction in the tissues; whether the same substances are inhaled from atmospheric suspension and accumulate in the lungs in dangerous quantities can be demonstrated only by inhalation. The reactions that I shall discuss first took place not in the lungs but in the liver. For the purpose in hand this is quite immaterial for we are merely seeking to discover whether these minerals are capable of produc-

Jan 1, 1938