Search Documents

By W. A. Ver Wiebe

The year 1940 was singularly unmarked by sensational developments in Kansas. Routine operations were carried on in a systematic, orderly fashion and the efforts of oil producers were concentrated on extending known fields. In Kansas an arbitrary yardstick for wildcats has been set up. A well drilled mile or more from a known pool or well is now considered a wildcat. A "rank wildcat" is one that is drilled at least 2 miles from any known producer. During 1940, rank wildcats resulted in the completion of 116 test wells, among which 16 were successful in finding new oil pools and the remaining I00 were dry holes. The ratio of successful wells to dry holes, therefore, was approximately I:6. During the year, 1890 wells were completed in eastern and western Kansas. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or wells that were recompleted in a different geological horizon. About three fourths of these (1423) were completed as commercial oil wells (I220 in western and 203 in eastern Kansas). The commercial gas wells completed number 58 of which 10 are in eastern Kansas and 48 in western Kansas. Of the remzining completions 147 are dry holes in eastern and 262 are dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year account for a cumulative initial production of 46,000 bbl. in eastern and 2,128,000 bbl. in western Kansas. The state of Kansas attained a new peak in production, with the total of 66,245,000 bbl. for the year 1940, the number of contributing wells being 20,779. Thus the increase over 1939, when about 58 million barrels was produced, is considerable. The previous peak occurred in 1937, when 70,761,000 bbl. was marketed. In another still earlier peak, in 1917, slightly more than 45,000,000 bbl. was produced and sold. The production of gas probably reached a new peak also during 1940, with its total of 85 1/2 billion cubic feet. Between the peak of the year 1908, when over 80 billion cubic feet was produced, and that of 1940, the production dropped to a low point of 16 billion cubic feet in the year 1921. The number of test wells drilled was larger than in 1939; that is, 1890 compared with 1458. The first peak was reached in 1904, when 2782 wells were drilled. The number dropped off rapidly, to 368 three years later, but rose to the second and highest peak in 1918, when 4671 test wells were completed. In the period between 1904 and 1912 more gas wells were completed than oil wells. Between the high peak of completions in 1918 and somewhat lower peak of 1937, the low point was reached during 1931, with the completion of only 470 test wells. In the number of new pools discovered, Kansas again ranks high among the states. The exact number depends somewhat upon the interpretation of a "new" area— whether it should be called a new pool or a long extension of an old pool. Unfortunately, the matter of securing the right kind of production allowable also enters into this question. Often the decision regarding a new pool cannot be made until other wells

Jan 1, 1941

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By R. M. Brick

AN increased demand for information in regard to the effect of gaseous elements in steel has accompanied the recognition of the importance of grain size. Attempts to correlate grain-size characteristics with gas con-tent, particularly oxygen in solution or in the form of included metallic oxides, have not been universally successful. Certain definite effects of dissolved gases are recognized; specifically, the role of hydrogen in causing internal cracks or "flakes" and that of nitrogen in preventing excessive grain growth of ferritic chromium steels. When irregular behavior or properties are found in a well-known steel and no definite cause for the abnormality may be assigned on the basis of chemical and metallographic tests, dissolved gases are frequently blamed as the culprits. The solubilities of hydrogen1 and nitrogen2 in pure liquid iron are known but of the ternary systems, iron-alloying element-gas, only the Fe-Si-N3 and Fe-Cr-N systems have received attention and here the study was confined to liquid alloys. Krivobok4 published a curve show-ing the solubility of nitrogen in liquid Fe-Cr alloys but gave no informa-tion on the experimental procedure employed. The considerable experimental work reported on the Cr-N binary alloys has been reviewed by Hansen.5 It is generally agreed that the nitride CrN is a stable phase although the existence of nitrides within limited temperature ranges of stability, viz., Cr3N2 and Cr2N, has been disputed, Adcock6 and others7 have reported a eutectic between Cr and CrN at 1580°C., although the supporting evidence is not complete.

Jan 1, 1940

By Alan Morris

Season cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes arc fairly well understood and means for its prevention are inexpensive and effective, so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,' in discussing a paper by Hatfield and Thirkell, says: " He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultaneous corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack. Dr. McAdam3 has investigated the effect of corrosion on the fatigue limit of brasses, among other materials. He directed a stream of either fresh or salt water against the specimen while it was undergoing fatigue test. The corrosion-fatigue limits thus determined may be considerably lower than the endurance limit without coincident corrosion. The exact

Jan 1, 1930

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By E. A. Gulbransen, W. S. Wysong

THE behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a metal or as an important component in alloys in high temperature oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a microbalance study1,2 of the following problems: (I) the oxidation behavior in the temperature range of 25 to 550°C (2) the reduction with pure hydrogen of thin oxide films formed on tungsten, and (3) the volatility of thin oxide films on tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the oxide to metal volume ratio is greater than one, the oxide is not considered protective, (2) the metal readily oxidizes at temperatures from 300° to 550°C (3) the oxides W02 and WO3 are reduced at temperatures as low as 500°C. by hydrogen, and (4) the oxide W02 is volatile at temperatures from 800 to 1100°C. LITERATURE The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°C. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides. Scheil4 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bedworth5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.7 They have reported that W03 is the stable oxide in contact with the metallic substrate up to approximately 600°C while W02 forms first at 700°C. Hägg and Magneli8 have recently reported a study of the lattice structures observed in the tungsten oxides using the X-ray diffraction method. In addition to an a-phase W03 and a d-phase W02, they reported the existence of two new phases. A ß' phase, homogeneous between

Jan 1, 1947

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By J. P. Pritchard, J. T. Pierce, O. G. Slay

This paper discusses the results of a technology-evaluation program to ascertain the feasibility of a piotornask-photoresist technology developed for fabrication of multiple-layer thin-film superconductive circuitry. The uehicle selected for this evaluation was a 120-bil associative data processor requiring a set of nine photomasks to define a similar number of patterned material layers of lead, tin, and polymer insulation. A total circuit area of 4 sq in. involved 2500 actitle and 12,000 passive crossings. Several short-free, electrically continuous specimens were satisfactorily completed under this program. Problems encountered in the preparation and use of the requi-ed set of Photomasks are discussed, as also are the problets of providing suitable external connections. A major retarding factor in the development of the superconducting thin-film cryotron technology for many years was the absence of batch fabrication means yielding necessary device density and count per substrate for practical applications. Early workers in the field desired only limited numbers of devices to permit careful study of discrete devices and representative circuitry integrating logic and memory capabilities. For these purposes mask stencils could be formed to selectively control the placement of materials, sequentially vapor-deposited in vacuum, to form the multilayer structure. In general a distinct pattern was required for each material layer; therefore, mechanical provisions were required to change not only the material source, but the patterning mask as well, before each deposition. All deposition steps were preferably performed in a single evacuation of the deposition chamber. Thus the means for storing, transporting, and registering masks and sources with respect to the substrate existed and were operated within the vacuum environment. In the authors' experience, the approach was and remains serviceable for preliminary device study, but was not extensible to an economical manufacturing method by virtue of the difficulties inherent in mask stencil preparation and use, and the capital investment implicit in the mechanization requirements. Since the commercial attraction of the cryotron technology stems principally from its potential for economical batch fabrication, the authors' program has placed major emphasis on fabrication methods. A highly useful method has evolved through adaptation

Jan 1, 1967

By L. Guttman, C. S. Barrett, J. S. Bowles

THE transformation from the face-centered cubic (Al) to the face-centered tetragonal (A6) structure in certain alloys of the indium-thallium system reported in the preceding paper1 exhibits many interesting crystallographic and metallo-graphic features, most of which presumably are similar to those of other cubic to tetragonal transformation such as, for example, the one which occurs in the chromium-manganese system,2 the one which, judging by microstructures and X-ray pat-terns,3 probably occurs in the copper-manganese system, the ones accompanying ordering in FePt,4 Copt,&apos; and AuCu,5 and the transformation near 115°C in barium titanate.6,7,8 If, as mentioned in ref. 1, the transformation is second order, the phases in equilibrium do not differ in composition, and it is both possible and likely that the mechanism is a diffusionless one. The present paper reports the results of a detailed study of the indium-thallium transformation and presents a theory for the atomic movements of the transformation which accounts for the observations. Experimental Crystallography of Transformation Markings The transformation from cubic to tetragonal in the indium-thallium alloys produces microstruc-tures of the type illustrated in fig. 1. These structures are observable either as relief effects produced on a smooth surface by the transformation, or after polishing and etching. These microstruc-tures are markedly similar to those found in copper-manganese alloys: iron-platinum alloys," and barium titanate,7,8 where it has been demonstrated that the lamellae are parallel to the (101) planes of the original cubic crystal. That the observed lamellae in indium-thallium alloys are also parallel to the (101) planes was proved by the following analyses performed on single grains in polycrystal-line samples containing 20.75 atomic pct T1. A study of the microstructures of a number of specimens revealed the fact that in many specimens the transformation markings continued unchanged in direction across the (111) interfaces of annealing twins. This at once demonstrates that the lamellae are parallel to a plane that is common to both parent and twin orientations, i.e., a plane in the zone <112>. This conclusion is compatible with the lamellae being parallel to (101) planes. To make a more complete determination of the habit plane of the lamellae, two grains were selected in which annealing twins ({Ill) twins) had been present in the high-temperature modification (cubic). The traces of the annealing twins, and of the transformation markings in both parent and twin crystals, were plotted together in stereographic projection, and a parent-twin pair of orientations was found that accounted for all lamellae as (101) planes. The projection of one of these twinned grains is reproduced in fig. 2. In view of these results the probability of there being another solution for the habit plane remote from (101) is very small, but to explore the possibility that the habit plane deviates slightly from (101), a more precise analysis was undertaken. In this, the orientation of a grain in the cubic modification was determined from a Laue back-reflection photograph taken with the sample at 90°C. The traces of the lamellae that formed in this grain on cooling were plotted in the stereographic projection

Jan 1, 1951

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite

By R. A. Swalin, A. H. Geisler

THIS study represents an investigation of the effect of annealing temperature on the texture of drawn molybdenum, iron, and an iron alloy containing 14 pct Al. The effect of temperature on annealing textures has not been widely investigated in the past. One of the obstacles in making such a study using usual X-ray diffraction techniques results from the

Jan 1, 1957

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

By Carl Samans

THE attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewski1 were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials hag been supple-mented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantita-tive data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures.

Jan 1, 1934

By H. N. Wolcott

AMONG the many cases of replacement of one mineral by another, that of quartz or silicates by pyrite, or even other sulphides, is not uncommon, but the reverse of this process does not appear to have been recorded, even if it has been observed. It, therefore, seemed to the writer that the case described below was worthy of record. FIG. I.-GROUND MASS OF CHALCOPYRITE (C) CONTAINING ROUNDED GRAINS OF PYRITE (P) SHOWING DIFFERENT DEGREES OF REPLACEMENT BY QUARTZ (Q), AND ALSO QUARTZ VEINLETS CUTTING THROUGH THE PYRITE. (PHOTOGRAPHED BY REFLECTED LIGHT.) The specimens described in this paper were obtained by R. B. Morton of Idaho Springs, Colo., from the Old Town Mine, in Russell Gulch, and are in the collection of Cornell University, where the writer studied them. In the rough, the specimens appeared to consist largely of chalcopy- rite, with some grains of tetrahedrite. The polished surface of some of

Jan 6, 1917

By Arthur L. Bishop

INTRODUCTION Purpose The in-situ leach method for uranium extraction is a relatively new and innovative method of uranium mining. In 1975, the first commercial in-situ facility began operation in south Texas. Since that time numerous other operations have been initiated as either pilot or commercial ventures. Considerable literature has been published that deals primarily with generalities of the process or environmental concerns. Several federal agencies have published documents which do not reflect the true operating or environmental nature of the in-situ leach method of uranium extraction. From an environmental standpoint, this is also evident in the promulgation of rules and regulations. Hence, the purpose of this paper is to present experience with an environmental concern--non- production zone excursions--such that the industry and the regulatory agencies will gain greater insight devoid of preconceived ideas and misconceptions. General Process Description In south Texas, in-situ leach mining is utilized to extract uranium from permeable sandstone ore deposits 61 to 213 meters (200 to 700 feet) below the surface. Uranium is present as an insoluble uranium oxide. In the in-situ or solution mining technique, anoxidizing lixiviant is injected into the formation through injection wells. The solution reacts with the insol uble carbonate complex. This soluble uranium complex is produced at recovery wells, each containing a submersible pump. During production there is a constant sweeping of lixiviant through the formation from the injection wells to the recovery wells. Injection and recovery wells can be arranged in any of a number of geometric patterns dependent upon ore body configuration, aquifer permeability, and operator preference. Submersible pumps in the recovery wells pump the uranium rich pregnant solution to the initial processing facility. Monitor wells surrcsund the pattern area and are screened in appropriate stratigraphic horizons (production and non-production zones) to detect any lixiviant migration that may occur (Fig. 1).

Jan 1, 1980

By R. J. Marcotte, C. T. Eddy, R. J. Smith

THE objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. CAST STEELS The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition-all of which is summarized in Table I. [ ] PROCEDURE The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By Reno H. Sales

EVERY mine manager, mine geologist, and every prospector in the field who appraises the future of mining properties does so on the basis of a theory of ore deposition whether he recognizes this fact or not. Wherever the ultimate value of a mine or prospect is dependent upon undeveloped ore, any estimate by an engineer or geologist necessarily involves a theory of origin of the deposit. In view of these facts the importance of a thorough understanding of the genesis of ore deposits cannot be overestimated. It well may be that the greatness of our country will depend upon finding reserves of natural resources as yet undiscovered. The genesis of ore deposits offers a fascinating field for study and investigation. This is attested by the large number of geologists who have written at length on the subject. For progress made toward a better understanding of ore genesis we owe much to Kemp, Lindgren, Ransome, Vogt, Emmons, Spurr, Graton, and a host of others. Within my own experience, I have attempted to apply in practice the various concepts and theories that have been advanced by these men.

Jan 5, 1954

By John Devine

DURING the past few years the Bureau of Mines has been studying hydrogen-sulfide corrosion in the petroleum and natural-gas industries. Early work was confined to investigating the various practical, or operat-ing, factors that control the corrosion reaction when ordinary mild steel is being attacked. In that work it was shown that, if the optimum operating conditions1 are obtainable, . gas containing hydrogen sulfide can be handled at ordinary temperatures without serious corrosion resulting. However, frequently "sour" gas must be handled under other than optimum operating conditions, and combating corrosion then becomes a problem to be considered more during the construction of a system than during its subsequent operation. That is, where economi-cally practicable in such cases the designer will seek to substitute for mild steel other steels or ferrous metals more resistant to corrosion by hydro-gen sulfide. The comparative resistance of various commercial steels and alloy steels to corrosion by hydrogen sulfide at elevated temperatures has been reported systematically by previous investigators,2 but similar information for corrosion at ordinary temperatures is available only from scattered sources, representing different methods of testing. As the value of comparative corrosion tests depends largely upon the use of a

Jan 1, 1934

NEW MEMBERS The following list comprises the, names of those persons who became members during the period June 10 to July 10, 1914: Members ALDRICH, HAROLD W., Supt. of Leaching Plant, Washoe Red. Wks., Anaconda Copper Co., Anaconda, Mont. AYER, FRANK ASHTON, Mine Foreman.. ..Detroit Copper Co., Morenci, Ariz. BELL, ARTHUR F. L., Chief Engr., Associated Oil Co.., 817 Sharon Bldg., San Francisco, Cal. BERGMAN, JULIUS GUSTAF, Mech. Engr., Chief Draftsman, Arizona Copper Co. Morenci, Ariz. BURT, CURTIS F., Min. Engr., Pittsburg-Dolores Mining Co., Rockland, via Yerington, Nev. CALLAWAY SCOTT DAVID, Chem La Harpe Smelter Co., La Harpe, Kan. CAMPBELL, W. C., Min. Engr 4 Princess St., Roodeport, Transvaal, So. Af. CARROLL, GEORGE A., Genl. Mgr Kildare Min. Co., Manson, B. C., Canada. CARUTHERS, JOHN LYTLE, Min. Engr., Asst. Engr., St. Louis, Rocky Mountain & Pacific Co.. Raton. N. M.

Jan 8, 1914

By I. Cadoff, J. P. Nielsen

The Ti-C phase diagram exhibits a peritectic point at 1750°C and 0.8 pct C, and a peritectoid point at 920°C and 0.48 pct C. The maximum solubility of carbon in a titanium is 0.48 pct. The 6 region containing the Tic compound (20 pct C) extends to 11 pct C at the peritectic temperature. THE interest in the Ti-C alloy system stems from the fact that carbon occurs as an impurity in titanium alloys when graphite electrodes or graphite crucibles are used in their melting. Since titanium-base alloys are still in the development stage, some virtue may be found in carbon addition to titanium. The Tic compound is currently emerging as an important powder metallurgy base constituent similar to the WC compound. Ehrlich&apos; identified the phases and structures present in the Ti-C system. The peritectoid region of the phase diagram was investigated by Jaffee et al." A preliminary diagram based on theoretical considerations was proposed at the outset of this research." The Tic compound has been investigated extensively and has been reported on in a large number of papers. Experimental Procedure Arc-melted alloys of 24 compositions in the range 0 to 20 wt pct C were investigated using metallography, X-ray diffraction, and, for the liquidus and solidus regions, incipient and complete melting. All alloys were prepared from iodide titanium (New Jersey Zinc Co., 99.95 pct Ti minimum) and spectroscopic grade carbon (National Carbon Co.). To prevent carbon spattering during arc melting the carbon was encapsulated in titanium. For alloys containing less than 1 pct C the powder was inserted into a capsule formed by drilling a hole in the as-received rod. For higher compositions, capsules were formed from titanium sheet. Arc Melting: The charges were melted in the copper-hearth cold electrode furnace shown in Fig. 1. This furnace is similar in principle to the all-metal unit adapted for titanium melting at Battelle Memorial Institute.&apos; The transparent pyrex walls giving unlimited visibility during operation and the multiple-

Jan 1, 1954