Search Documents

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By George Smith

ChillaQoe is situated in latitude 17" S., about 138 miles from the port of Cairns, with which it is now connected by rail. A township has been established on the banks of Chillagoe creek, a perennial stream of irregular volume crossing the field almost at rightrangles, nearly midway between the mining-camps of Calcifer and Mungana, which have been formed at the southeastern and western extremes of the field respectively. This situation was selected because of the water-supply and its proximity to the site most suitable for the erection of reductionworks. By its central position it commands the whole of the mines. The altitude above sea-level is about 1200 ft., whereas that of Calcifer and Mungana is 1400 ft.—a difference sufficient to account for a materially higher temperature at Chillagoe. The surrounding limestone bluffis add by radiation to the heat, and, at the same time, prevent the cool breezes from passing freely through the town; consequently, the temper* ture, which is high throughout the year, and especially so during the summer months, is here ge~ierally very oppressive also. The general trend of the field is southeast and northwest, and its length about 18 miles, with an average width of 5 miles; the approximate area is thus 90 sq. miles. The surrounding mineral-district is, however, much more extensive, and numerous other mines, sprcad over wide areas and producing a variety of minerals, exist in the same or parallel belts of mineralized country, of which Chillagoe proper covers but a very small portion. Immense bluffs of limestone, wollastonite and conglomerate, rising in places to nearly 300 ft., and so~netimes nearly a quarter-mile across, give the field a very picturesque and interesting appearance. The limestone has been classified as Devo-

Jan 1, 1904

By Donald Cummings

CERTAIN dusts are dangerous when inhaled, but most hazardous of all dusts are quartz or other forms of pure crystalline silica. The inhalation of dusts containing silica in combination with other elements gives rise to changes in the lung which differ from those produced by pure silica. As a generality, silicates are less dangerous than pure crystalline silica and vary greatly among themselves in harmfulness. Repeated analyses have shown that approximately 70 per cent of the total number of particles involved in any dust-producing operation are below 1 to 2 microns in diameter. (A micron is. approximately 1/25,000 in.) Similar studies of dusts recovered from silicotic lungs post mortem have demonstrated essentially the same size frequency distribu-tion, except that the upper limit of size retained in the air sacs is approxi-mately 10 microns. Experiments carried on by Gardner and the author have further demonstrated that greater changes were produced by a fixed weight of very fine quartz particles (2 to 3 microns and smaller) than by the same weight of slightly larger particles (8 to 10 microns). Any attempt to control a dust hazard should therefore be directed toward the removal from the working atmosphere of particles less than 10 microns in size, and particularly those below 3 microns. All industrial hygienists agree on this matter, but there remains considerable dispute as to the lower limit of particle size capable of causing injury. It has been gen-erally conceded, however, that particles of harmful dusts smaller than ¼ to ½ micron are not essentially concerned in the development of pulmonary fibrosis. This opinion is partly substantiated by the existence of large numbers of these small particles in practically all atmospheres that are, not associated with any known hazard. Such particles are so small that they have very little mass, fail to settle even in quiet air, and probably are not easily retained in the lung. Until further research proves that they are involved in the dangers provoked by the inhalation of certain dusts, engineers will generally agree that it is better to dis-regard them.

Jan 1, 1935

By J. M. Locke

BRÜCKNER's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. As examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,, Ohio, are shown in Plate III, in which Fig. 1 is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a trans¬verse section. Fig. 4 is a sketch of a mill, with Brückner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches.. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi¬circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15° to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30° to 35° to the longitudinal, axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

Jan 1, 1874

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers' Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present. The meeting was called to order by Vice-Chairman Albert Sauveur, who introduced the speaker of the evening, Utley Wedge, of Ardmore, Pa. Mr. Wedge read his paper on the chloridizing roasting of copper ores, which he illustrated with a stereopticon, and which will be published in full by the Institute. After Mr. Wedge had closed his paper, which was received with great interest by all the members, the following discussion took place: Professor Hofman said that iron was formerly thought to ho essential to the Henderson process, but that it is not absolutely essential. Mr.Wedge said that, as far as he. knew, the presence of some sulphates was an abso¬lute necessity, and that line ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel was needed with the muffle furnace. By direct firing he has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the gases from the upper hearth are not used. There is doubtless some temperature at which the loss. from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced. The copper apparently does not become volatile at. the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913

By R. F. Favreau, G. E. Larocque

The objective of the study is development of an analytic process based on rock and explosive properties which allows the prediction of the stress distributions and fracture zone around explosive charges. A computer program has been written for this purpose, using a finite difference approximation to the momentum equation, to describe the motion of the surrounding rock by step-wise integration. Its application provides ground motion data such as stress components, displacement and particle velocity as a function of position and time with respect to a spherical charge. The effect of tensile and shear failure on these ground motion parameters can be included. The analytic procedure contained within this program has been used to predict peak stress as a function of distance in rock for rock-explosive combinations for which field data exists to determine peak stress levels directly. Two methods have been used for the spherical charge which in the analysis replaces the actual cylindrical charges: instantaneous application of peak pressure to a charge having a radius equivalent in contained volume to a charge having a length to diameter ratio of 1, and gradual pressure build up to peak pressure with a charge radius equivalent in contained volume to the total charge used in the field test. The agreement with field data would appear best with the latter treatment. The peak stresses obtained are in closer agreement with field measured peak-stress and a better approximation to field stress wave duration exists in the case of gradual pressure build up. One of the assumptions made in the analysis is that, in the case of cylindrical charges, the explosion pressure rather than the detonation pressure of an explosive establishes the peak stresses in the

Jan 1, 1971

By Joseph C. Mead, James R. Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources Of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There are also two blast furnaces at Gadsden and one ferroalloy electric furnace at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron.

Jan 1, 1937

By C. Schlumberger, M. Schlumberger

The object of this paper is to clarify the idea, so important when exploring by potential methods, of the depth of investigation attainable by electrical measurements. After defining, with some precision, .the term "depth of investigation'' in geophysics, the authors show how it is possible to regulate this depth in potential methods and to obtain an 'electrical drilling" from surface observations. They consider also the difficulties encountered in deep measurements and indicate how it is possible to reach greater depths than those having an industrial interest. Depth of Investigation The term, depth of investigation, in its general sense, is easily understood. For instance, a driller who can pull cores from a depth of 2000 m. is capable of working, with accuracy, to that depth. By means of a properly placed drill, he may locate an orebody at a depth of 1999 m., however small this orebody may be. On the contrary, the term as used in geophysics requires precise elaboration. As a matter of fact, no geophysical method, irrespective of the physical property studied (density, magnetic permeability, conductivity), can discover a very small body at a great depth because, in practice, the physical parameter upon which such a geophysical method is based is never regular enough, throughout the ground, to distinguish the feeble anomaly caused by the small, deep-lying body from the numerous anomalies due to irregularities of the encasing terrains. Aside from this question of the ratio between the size of the body being hunted for and its depth of burial, a second factor plays its role in the possible depth of investigation; that is the difference, for the parameter under consideration, between the body and its surrounding material. The greater this difference, and the more homogeneous the encasing terrains, the greater is the possible depth of investigation. This being generally established for all geophysical methods, it is possible to distinguish two main classes of these methods, from this same point of view

Jan 1, 1932

By Charles Pack

DIE castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into threee groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. CASTING MACHINES The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly. apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings.

Jan 2, 1919

By A. J. Lanea

INDUSTRIAL MEDICINE bids fair to become one of the most important and highly developed branches of medical science. Mining companies, even in remote districts, have developed large and efficient medical organizations that comprise the best types of physicians and surgeons. Not infrequently, however, company medical departments have been influenced too much by local conditions-including the compensation laws, which differ widely in the various states. The possibilities of industrial medicine are just beginning to be generally understood, and the variations in the organization and aims of medical departments of mining companies are no more pronounced than in industry as a whole. The industrial physician should be as much a part of the organization as any other official and he should know intimately the various types and phases of work in the plant and should look at his work from the viewpoint of the needs and requirements of his particular industry and company. He should not-be on the outside looking in, but on the inside, working hand in hand with the superintendent, manager, foremen, employment director, safety director, and anybody else with whom in his work he might associate. In any industry it is essential that the doctor be-familiar with working conditions. The mine doctor who never goes underground must remain ignorant of the factors causing many of the disorders he treats as well as miss the best opportunity of gaining the respect and cooperation of the men he. serves. If the mine doctor remains unfamiliar with underground working conditions he bars himself from valuable preventive medical work. It is estimated that the time lost by industrial workers, as a whole, because of illness is about four times as great as that lost because of accidents. While the effort to determine the responsibility of working conditions for illness is often futile, there is a wide field, both for study and practice, in the lessening of sickness among industrial workers. The first step in this direction must be a knowledge of the factors involved.

Jan 2, 1921

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St.., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers' Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present.. The meeting Was called to order by Vice-Chairman Albert Sauveur, Who introduced the speaker of the evening, Utley Wedge, of Ardmore. Pa. Mr. Wedge read a, paper on the chloridizing roasting of copper ores, Which lie illustrated With a stereopticon, and Which will be published in full by the Institute. After Mr. Wedge had closed his paper, Which was received with great interest by all the members. the following discussion took place: Professor Hofman said that iron was formerly thought to bo essential to the Henderson process, but that it is not absolutely essential. Mr. Wedge said that., as far as he knew, the presence of some sulphates Was an absolute necessity, and that lime ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel Was needed with the muffle furnace. By direct firing lie has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the uses from the upper hearth are not used. There is doubtless some tem-perature at Which the loss from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced.. The copper apparently does not become volatile at the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that Were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913

By Dennis A. Clark, Brent Larsson

Tunnelling today is a lot more than drilling and blasting. The developments in drilling and blasting technique have made it pos¬sible to save costs both by increasing the advance per round and optimizing the demands on the final contour. Increasing the hole depth by using longer feeds and bigger dril¬ling rigs make the drilling time shorter compared to the set up time. It is important that the deeper holes are followed up by using a suitable cut. The most common cut in Sweden today is a parallel hole cut with one or more large holes; with a diameter corresponding to the hole depth and wanted advance per round. It is often specified that smooth blasting is to be carried out with a specific drill hole spacing. It is extremely rare, however, for specifications to be issued concerning the alignment of the raw of holes closest to the contour holes. It is very easy to ruin the effect of smooth blasting altogether by firing the rest of the round carelessly with an excessively high charge distribution. The drilling and blasting of the contour holes and the line of holes closest to the contour holes is therefore an extremely important part of any underground work. Accuracy and care in connection with the drilling of contour holes is also extremely important since it is possible to reduce the amount of overbreak, the result being more rapid mucking out, smoother and more durable surfaces and also less consumption of concrete for lining purposes.

Jan 1, 1983

By R. F. Hollis, C. K. McArthur

PRIOR to the application of anion exchange, all recovery of uranium from acid leach liquors precipitated an impure product requiring further upgrading before it could be refined. The ion exchange process, on the other hand, provides excellent selectivity for extracting soluble uranium from leach liquors, so that high grade concentrates can be produced directly. The discovery that uranium is readily adsorbed by anion exchange resins, together with the experience of resin and equipment manufacturers in water treatment, led to rapid development of ion exchange in a multiple column operation. Many processing plants using fixed bed ion exchange are in operation or under construction in Africa, Australia, and Canada. There are a limited number in the U. S. Although the fixed bed process has been highly successful, the feed to the ion exchange columns must be a clear solution, which is obtained by filtration or by countercurrent decantation of leached pulps. With some ores, poor filtration or settling characteristics make production of a clear solution difficult. Most processing plants in the U. S. receive their ores from a number of small mines, and there is considerable variation in the settling and filtering behavior of the ores. An ion exchange process was therefore desirable in which the uranium could be recovered directly for the leached pulp by adding ion exchange resin, which could be then separated from the pulp by a screening operation. The process would thus resemble the cyanide-charcoal process in which gold is adsorbed from cyanide pulp by means of activated charcoal. Preliminary tests in which leached pulps were directly contacted with resin beads led to the development of the RIP process.

Jan 4, 1957

By O. G. Lellep

IN every country economic circumstances prescribe the method used to produce a commodity at lowest cost. In Pennsylvania a man's wages for working 4 hr buys a ton of coal wholesale; in Germany a laborer must work 40 hr, or ten times as long. In western Europe, therefore, conservation of fuel is of primary importance, and recent practices of burning lime and cement differ from those employed in the United States. This paper presents data collected during a trip through western Europe in 1953. Considered uneconomical, shaft kilns for burning cement disappeared in the United States two generations ago. But because required capital investment is low and operation greatly improved, shaft kilns are still used to some extent in Europe, where fuel costs are high, and are even included in designs for plants under construction. During the last 50 years shaft kilns have been maintained at the same physical size, while their output has been increased at least four times.

Jan 7, 1954

By R. W. Raymond

That the death of Martin Coryell, which occurred at Lambertville, New Jersey, on Monday morning, November 29th, touched the sympathies of a wide circle of professional associates and personal friends, was amply testified by the gathering at the funeral services on Friday. Like his distinguished friend and neighbor, the late Ashbel Welch, Mr. Coryell was one of those pioneers in American engineering to whom we owe the great railway and canal systems which lie at the base of our national prosperity, and who have consequently enjoyed the respect and esteem of their successors of the present generation. Martin Coryell was born July 20th, 1815, at New ope, Rucks County, Pa., and was educated principally in the schools of his native town arid of Lambertville, New Jersey, to which place he returned for permanent residence fifty years later. With the exception of a brief period in youth, during which, to restore his failing health, he learned and practiced for a few months the carpenter's trade, and another brief period, later in life, when he read law for a time in the office of B. H. Brewster, of Philadelphia, afterwards Attorney-General of the United States, Mr. Coryell may be said to have spent his life as an active civil and mining engineer. Even these two episodes can scarcely be said to have been deviations from that profession, since they served to give him more thorough preparation for constructive and administrative work. The Delaware Division Canal, the Raritan Canal, and the Brunswick Canal, are among those upon which Mr. Coryell was employed. For the Raritan Canal Company, under the superintendence of Ashbel Welch, he located the greater part of the Belvidere Railroad (now the Belvidere division of the Pennsylvania Railroad), and directed its construction from Trenton to Lambertville. He was also active as a mining engineer, being one of the early pioneers of mining in the Lake Superior copper region, and had much to do with the development of the Hazleton coalfield and the railroad which has since expanded into the Lehigh Valley system. In 1862, he removed to Wilkes-Barre, where, in 1864, he became manager of the Warrior Run Mining Company. One of the editors

Jan 1, 1887

By A. S. Michaels, R. S. Timmins

A study of the effect upon oil recovery from an un-consolidated porous medium of chromatographic transport of selected reverse-wetting additives during water displacement is described. Flow tests were performed on hydrocarbon oil-saturated sand columns (containing connate water) into which small volumes of short-chain aliphatic amine solutions were introduced during water flooding. Concurrently, meusurements of oil-silica contact angles, oil-water interfacial tensions and oil-water distribution coefficients were measured us a function of additive concentration. Certain treatments were found to cause a slight reduction in oil recovery, while others produced a significant increase (up to 50 per cent of the normtzl irreducible rninimum oil saturation). Recovery eficiency was correlated most satisfactorily with the maximum degree of reverse wetting produced during additive transport; conditions which resulted in only mild oil wettability of the sand reduced recovery, while those favoring strong oil wetting increased recovery. A mechanism of reverse-wetting additive action during chromatographic transport is developed which ascribes the results to transient changes in oil-solid contact angle during flow, with consequent release of oil trapped by capillary forces. Implications of these observations with regard to improved waterflood efficiencies are discussed. INTRODUCTION The need for finding improved methods of oil production is amply illustrated by the large volume of oil considered economically unrecoverable by existing production practice. Water flooding has long been an excellent method of secondary recovery. However, even in those areas of a formation which are well swept by a water flood, 20 per cent or more of the oil remains trapped within the formation and is not recovered. This trapping of oil within the pores of the rock structure results primarily from interfacial forces. If these interfacial forces were altered, it is possible that the trapped oil could be released and recovered. The addition of surface-active agents to a water flood to alter the interfacial properties of the oil-water-solid system has received considerable attention as a method of increasing oil recovery. Studies of surfactant treatment have yielded varied and, in some cases, apparently conflicting results. Increased oil recovery using surface-active agents has been reported by a number of investigators. Others have found that use of surfactants in a water flood either has no effect upon oil recovery or decreases it. Since surface-active agents tend to alter the formation wettability and oil-water interfacial tension simultaneously, several investigators have tried to determine the role these two factors play in oil recovery. Data have been presented which indicate that the most desirable condition for the solid surface is strongly water-wet. Other results indicate that, although breakthrough recovery may be less, the greatest ultimate recovery is obtained when neutral wettability prevails.", " The desirability of low interfacial tension seems to depend upon the wettability of the formation. Reports of higher recoveries, when the interfacial tension is high in a water-wet system and low in an oil-wet system, are at odds with reports of increased recovery in water-wet systems when surfactants which decrease the interfacial tension are added to the water flood. A review of previous work studying the effects of using surface-active agents in a water flood shows that these agents produce widely different effects and that opinions as to the role of the various interfacial properties are diverse. The consensus, however, is that the interfacial properties are quite important in the displacement of oil from a porous medium by water. Even in those investigations where appreciable increases in oil recovery resulted from treatment with a surface-active agent, economic considerations generally made practical application of the treatment unattractive because surfactants tend to be adsorbed within the formation. This adsorption would necessitate using large quantities of surfactant if all of the flood water were treated to contain a given surfactant concentration, even if this concentration were quite low. Preston and Calhoun suggested that the principles of chromatography could be applied to the use of surface-active agents as a means of increasing oil recovery. A small volume of surface-active material is injec-

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky' made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans's solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

By Guy W. Jordan, David P. Hale

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By R. G. Knickerbocker

THE copper smelter and refinery of The Messina (Transvaal) Development Co. Ltd., at Messina, South Africa, was erected in 1920 and 1921, but initial operations were deferred until late in 1922 on account of the collapse of the copper market in the interim. Because the anticipated production was to be only 20 tons of copper per day from a high-grade matte containing 60 per cent copper, and because the ore did not contain gold or silver in quantities sufficient to pay for separation from the copper bullion, it was decided to design the plant along lines quite different from the modern smelteries treating large quantities of sulfide ores carrying appreciable amounts of gold and silver. The plant was built, therefore, for the production of copper by the Nicholls-James process. By this method two-thirds of the copper matte produced was roasted in a Merton calciner and charged into a bath of the remaining one-third portion of unroasted matte in a reaction furnace. The original design was not only novel in providing for the Nicholls-James process, but also in comparison with new plants built elsewhere, because of factors inherent in the locality. Sources of supply for machinery were very remote; it takes three months after the placing of an order to accomplish delivery of machinery into Messina from the United States. Native labor was available at 30 to 40¢ per 8-hr. shift. These factors permitted plant design which provided no overhead cranes, no matte ladles, no slag pots or other usual mechanical means of transportation between departments. The design resulted in a compact simple plant with furnaces arranged close together and. terraced so as to provide for gravity transfer of molten material from one furnace to another and for manual disposal of products. Fig. 1 shows the relative location of furnaces. The three furnaces are parallel on successively decreasing elevations. A superimposed feed floor was provided above the furnaces. All three furnaces were provided with coal-dust burners served from a Bonnot system of coal-dust transportation, and the waste gases were discharged into waste-heat boilers.

Jan 1, 1932

By George Wolff

To THE average person, the purport of the items and figures on the balance sheet of a mining company are hazy and the real financial condition of the company is cloaked in obscurity. It is also likely that the satisfaction of the stockholder in his investment, as well as the determination of the prospective investor, rests more on the reputation of the company, his confidence in the management, the stated earnings per share and the dividends paid, than on a comprehension of the information contained in the balance sheet. The balance sheet of any company at best can only closely approximate the true financial condition as of a given date. Any item of asset, except cash, can probably be altered if another's viewpoint is applied. It is difficult and expensive to drill and explore an orebody to determine the entire tonnage of ore therein. Those inherent difficulties render it practically impossible to prepare an absolutely correct balance sheet of a mining company. It is possible, however, to present the facts of a mining company more intelligently and comprehensively than is usually done. With this in mind, a balance sheet of an imaginary mining company is submitted, with supporting schedules. The same fundamental principles hold true whether we consider a large or a small company. Less complexity is involved in dealing with the affairs of a smaller company. Therefore, for this purpose, the assumed company operates but two mines and a smelting plant. It has been deemed advisable to introduce the features of the operation of a mine acquired prior to March 1, 1913 and one after that date. The presentation therefore is concerned in one mine with the appraisement as of March 1, 1913 and in the other with the appraisement by reason of discovery. A consequential factor pertains to dividends paid from depletion reserves and therefore free of surtax to the stockholders. While supporting schedules, when necessary, give details of certain items on the balance sheet, it seems desirable to give further explanations with respect to some of them. This seems to be important because some mining companies do not treat the items as indicated on the statements submitted.

Jan 1, 1928