Search Documents

By M. Cohen, R. T. Howard

The purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature transforrnations have been summarized recently by Troiano and Greninger.' Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation (Mg) during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transformation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metal-lographic3 and dilatometric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Stewardi have shown that the Greninger-Troiano metallographic technique8 may be used not only for M, determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below M, in fourteen commercial steels. In the present paper, the Greninger-Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M., thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. Experimental Details Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M. temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1949

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature 1135°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators1,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By M. Cohen, R. T. Howard

The purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature transforrnations have been summarized recently by Troiano and Greninger.' Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation (Mg) during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transformation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metal-lographic3 and dilatometric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Stewardi have shown that the Greninger-Troiano metallographic technique8 may be used not only for M, determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below M, in fourteen commercial steels. In the present paper, the Greninger-Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M., thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. Experimental Details Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M. temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1949

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world's total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates are required for certain end uses, and these are produced from smaller colemanite-ulexite-probertite bodies. Sodium-free borate compounds also are produced from boric acid, which can be manufactured from either sodium or nonsodium borate minerals. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of over a million tons of B2O3. Leadership in supplying borates shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates, In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, CA is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, CA, the world's leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "10-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7 • 10H2O. In addition to ship¬ping all major refined borate products from [ ]

Jan 1, 1983

By R. M. Brick, Arthur Phillips

The Institute of Metals Division Lecture in 1936, given by R. F. Mehl, on diffusion in solid metals1, was introduced with the statement that "the phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this the process of diffusion is of first importance practically." In view of the scope of that lecture, it does not seem necessary to review the importance, history or present status of diffusion problems. One aspect of the subject of diffusion that has received little attention became of some immediate importance in the course of a study on segregation. When a solid solution alloy freezes, the familiar mechanism of solidification requires that the first nuclei formed be low in solute concentration, with a resultant normal segregation or coring effect during freezing. Theoretically, musion of solute atoms during solidification should result in a homogeneous solid solution. Actually, of course, it is impossible in most binary alloys to obtain a cooling rate that will permit diffusion to eliminate coring in the freezing dendrites. For a given alloy, the extent of diffusion attained up to the point of final solidification will determine the degree of enrichment in solute atoms of the final liquid phase. The flow of this liquid into dendritic contraction channels and the solute concentration of the liquid seem to be the determining factors as to whether the final gross segregation is normal, inverse or absent. The purpose of the present study of diffusion was to determine to some extent the separate diffusion rates of copper and magnesium into pure aluminum with a view to clarifying previous results on segregation in these alloys; i.e., the fact that under similar freezing conditions aluminum-copper alloys segregate inversely and aluminum-magnesium alloys segregate normally. Of concomitant interest were the questions of the homogenization times required for segregated ingots or partially melted, i.e., "burnt," structures, and the solution heat-treatment times required for cast, hardenable aluminum-copper and aluminum-magnesium alloys, for worked and annealed structures, and so forth.

Jan 1, 1937

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

By Roy A. Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced', at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces'. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905

By A. B. Calhoun

These mines, which belong to the Burma Corporation, Ltd., formerly a London company now incorporated in Rangoon, Burma, are situated in the semi-independent state of Tawng-Peng, one of the small divisions comprising the northern Shan states and erroneously known as part of Upper Burma. Bawdwin is approximately 23' 6' N. latitude and 97" 20' E. longitude, 450 miles north of Rangoon, 169 miles northcast of Mandalay and 50 miles south and west of the Province of Yunnan, China (see Fig. 1). Although the mines were worked by the Chinese during the Ming Dynasty, 1412 A. D., the most extensive operations took place between 1796 and 1851, when the mines contributed largely to the silver market of China. During the reign of Tung Chik, 1868 A. D., they were abandoned partly because of the Mohammedan rebellion in Yunnan, which made life and property insecure, but largely because of the difficulty of operating the mines on account of water and poor ventilation. Since that time practically nothing was done, although the Burmese kings are said to have made several sporadic attempts to work the mines, until 1891 when Europeans were attracted by the great slag dumps (assaying about 40 per cent. lead) which the Chinese had left after extracting the silver. After a railroad and smelter had been built and 200,000 to 300,000 tons of slag smelted for lead, exploration work was started and old workings cleaned out in order to locate the remnants of the orebody that it was supposed the Chinese had left. After two years of most discouraging work, the remains of a large orebody was discovered by the Dead Chinaman Tunnel or what is the 171-ft., or No. 2 level adit. From then on the development was rapid and today the Chinaman is considered one of

Jan 1, 1923

By William B. Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chair man of the Institute's Committee on Petroleum and Gas; as a pre1iminary.discussion of the fuel oils which are used in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, I suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220" F., nor burn under 320" F. In the Southwest, it has not been long since we had fuel oils that flashed as low as 110" F., and the average flash point over a considerable period was 151" F. Now we are using oil that flashes at about 30" lower than the former burning point, which was 258" F. In other words, the flash point has risen, on the average, 100"; and the burning point about 75".

Jan 1, 1915

By A. B. Calhoun

These mines, which belong to the Burma Corporation, Ltd., formerly a London company now incorporated in Rangoon, Burma, are situated in the semi-independent state of Tawng-Peng, one of the small divisions comprising the northern Shan states and erroneously known as part of Upper Burma. Bawdwin is approximately 23' 6' N. latitude and 97" 20' E. longitude, 450 miles north of Rangoon, 169 miles northcast of Mandalay and 50 miles south and west of the Province of Yunnan, China (see Fig. 1). Although the mines were worked by the Chinese during the Ming Dynasty, 1412 A. D., the most extensive operations took place between 1796 and 1851, when the mines contributed largely to the silver market of China. During the reign of Tung Chik, 1868 A. D., they were abandoned partly because of the Mohammedan rebellion in Yunnan, which made life and property insecure, but largely because of the difficulty of operating the mines on account of water and poor ventilation. Since that time practically nothing was done, although the Burmese kings are said to have made several sporadic attempts to work the mines, until 1891 when Europeans were attracted by the great slag dumps (assaying about 40 per cent. lead) which the Chinese had left after extracting the silver. After a railroad and smelter had been built and 200,000 to 300,000 tons of slag smelted for lead, exploration work was started and old workings cleaned out in order to locate the remnants of the orebody that it was supposed the Chinese had left. After two years of most discouraging work, the remains of a large orebody was discovered by the Dead Chinaman Tunnel or what is the 171-ft., or No. 2 level adit. From then on the development was rapid and today the Chinaman is considered one of

Jan 1, 1923

By R. H. Landshof, Reynold Q. Shotts, James A. Redding

GENERAL INTRODUCTION by R. Q. Shotts The sizing of coal particles is one of the most important beneficiation operations performed from the time coal is broken at the face until it is delivered to the customer. Indeed, in many cases it may be virtually the only such operation performed in that interval, although it is most often accompanied by some comminution. Sizing, as the term implies, is a separation of the broken coal particles into arbitrary groups, each group containing particles within restricted mass, volume or size limits. Size itself is not a rigidly defined property, but is actually determined more by the operating principles of the sizing device than by unique properties of the particles themselves. Particle size cannot be uniquely defined independently of particle shape. Taggart l says, "In fact, it is not possible to state the size of a single irregular body by means of a single dimension; such possibility exists only for regular polyhedra and their limit, the sphere." In view of the scarcity of regular polyhedra among coal particles, even though most appear to approximate a cube, we actually define size in terms of a surface opening through which the particle barely will or will not pass, or of two openings, the smaller of which retains all particles of the group under study and the larger of which passes all of them. Alternatively, size is expressed in terms of rate of settling of particles in a fluid under closely controlled conditions. Historical Sketch2-Taken from Coal Preparation, 2nd Ed. "Sizing is the process of separating mixed particles into groups of particles all of the same size or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. "In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes in the mine working places to recover coarse coal. The mining procedure left the fines in the mine.

Jan 1, 1968

By R. W. Ph. D. Raymond, Anton Filers, O. H. Hahn

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty furnaces exist in Utah, about as many in Nevada, five in Montana, and four in Cerro Gordo, Inyo County, California, it is obvious that a business so extended deserves attention. Wide apart as these different works are located, they have nevertheless to deal in nearly every case with the same or very similar circumstances and conditions, so that, with very few exceptions, virtually the same system of smelting is followed in all these establishments. This is the so-called method of reduction and precipitation in blast-furnaces. As the principal reasons for the employment of a blast-furnace process are to be considered : the low percentage of lead in the ores, the high price of the only available fuel, charcoal, and the exorbitant rates demanded for labor. The reasons why the reduction and precipitation process is preferred to a roasting, reduction, and precipitation process are the high prices of labor and materials, and the preponderance of oxidized ores over sulphurets, though in some cases the latter are quite abundant. The weight of these reasons will be better understood when the character of the ores to be treated and the object of the smelting are more minutely stated. The ores are in nearly all cases a preponderating mass of oxidized lead ores, such as cerussite, anglesite, and leadhillite, in which nests and nodules of undecomposed galena occur. Associated with these are : in Eureka, Nevada, arseniate of iron and arsenical pyrites, hydrated oxide of iron, quartz, and calcareous clay ; in Little Cottonwood Canyon and American Fork, Utah, iron oxide, and in some cases a combination of antimony, the nature of which I have not ascertained; also dolomite and quartz in widely varying proportions; in Bingham Canyon, Utah, only quartz and comparatively little oxide of iron, or iron sulphurets; in Cerro Gordo, California, oxide of iron, iron pyrites, antimonial compounds, copper ores, and, as gangue, carbonate of lime and quartz. In Argenta, Montana, occur, besides the above-named lead ores, pyromorphite, and molybdate of lead. The preponderating gangue of the Argenta ores is quartz, and there is here a larger proportion of galena than elsewhere in the West. In most of the localities named, the lead ores themselves contain sufficient silver to render its separation from the ore the main object of the smelting; but in some of the districts, and especially in Montana, the lead ores serve only to furnish the extracting agent for the silver of true quartzose silver ores, which at the same time contain a sufficient percentage of lead to make amalgamation impracticable. They are therefore beneficiated by smelting, although the lead itself has no market value.

Jan 1, 1873

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

ALASKA Established November 19, 1947 Meets fourth Monday monthly except June through August Term of office ends October Peter O Sandvik, Chairman Denny G Breaid, Vice-Chairman Douglas W Huber, Secretary-Treasurer School of Mines University of Alaska P O Box 337 College, Alaska

Jan 1, 1958