Search Documents

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I.

Jan 3, 1925

Jan 1, 1967

By Richard E. Chism

Jan 1, 1902

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

By C. David Mann

Metal prices continued to improve in 1964, resulting in the opening of new mines and re- activation of old ones. Larger and deeper shafts are being bored. At the AEC's Nevada Test Site, a 72-in. diam shaft is being bored to 3200 ft. In New Mexico a 1650-ft shaft was bored with a 48-in. bit, then reamed to 124 in. to 935 ft, and 102 in. to 1650 ft. Deviation was only 26 in. In California a shaft sinking machine has been developed which combines drilling and mucking equipment into one mobile, integral unit.

Jan 2, 1965

By Ernst M. Cohn

The demonstrations of the "Silent Sentry" by Union Carbide Corp. in 1957 and of a special tractor-plow by Allis-Chalmers in 1959 ushered in the technology era of fuel cells. The idea for direct conversion of chemical to electrical energy, first published in 1801 by Davy in England and Ritter in Germany, has been kept alive by a few people through 150 years: Grove built the first hydrogen-oxygen fuel cell in 1839; Mond and Langer made electrolyte contributions around 1890 that are still used today; Baur worked on coal-based cells from 1900; Bacon started his work in the '30's, which resulted in the first multi-kilowatt unit in the '50's; Davtyan studied molten-salt electrolytes in the '40's, followed by Ketelaar in the '50's; and Justi developed highly active electrodes in the '50's, to name only some of the pioneers. Despite the tremendous increase in research and development of fuel cells, these direct energy converters are still in their infancy. They will find their functional application in space, where power density must be maximized and product water utilized. These early systems will provide valuable experience in system engineering and reliability.

Jan 9, 1964

By AIME AIME

FEW mining schools possess an art gallery and certainly none can equal the collection of paintings depicting the mineral industries now hanging in the comparatively new building of the School of Mineral Industries at The Pennsylvania State College. Dean Steidle, who conceived the idea, early this spring boasted of 55 paintings in the collection, by 24 different artists, the gallery being appraised at $18,000. Since then, eleven additional paintings have been added. Opportunity will he presented for an inspection at the meeting of the Industrial Minerals Division, to be held at the College, Sept. 24-26.

Jan 1, 1936

Map

Jan 1, 1941

By H. F. Dunlap, R. R. Hawthorne

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By R. R. Hawthorne, H. F. Dunlap

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

Engineering Experiment Station, Kansas State College, Manhattan, Kansas. For publications or a list of publications, address the above Of the 29 Bulletins issued by the Engineering Experiment Station, a few on cement and road-building materials may well be listed here: Bulletin 12, Road materials of Kansas; 15, Tests of Kansas road materials, 17, Some strength characteristics of portland cement; 25, Volume change of concrete, 26, A study of fourteen brands of standard portland cement and four early-strength concretes, 28, The durability of concrete, 29, The effect of aggregate and other variables on the elastic properties of concrete

Jan 1, 1933

US 4,190,434 - In the thermal production of magnesium metal, a mixture of calcined dolomite, an iron- silicon-aluminum alloy as a reductant, and residual slag from the production of ferrochromium is smelted to evolve magnesium vapor, which is then condensed. The use of bauxite is lessened or eliminated because of the relatively high alumina content of the residual slag. R. Bonfils, A. Mena, C. Payn, and L. Septier, assigned to Ste. Francaise d’Electrometallurgie (SOFREM). Feb. 26, 1980. 6 pp. (75-10R). Filed: 6-14-78 (915,387). Priority: France, 6-24-77 (77/20,227).

Jan 1, 1982

By Jean A. Andre

In 1969 "Société des Mines et Fonderies de Zinc de la Vieille-Montagne" produced 221,000 tons zinc ingots and 22,000 tons zinc dust, thus rating highest on the world's zinc producer list. The Company's plant at Balen, Belgium, with an output of 135,000 tons electrolytic zinc is the most important one of this group; it is an integrated metallurgical zinc and lead unit with recovery of most by-products. The present paper describes the zinc production facilities. The roasting section includes four fluid bed roasters (total concentrates charged: 740 tpd) and two sulfuric acid having a corresponding capacity. Calcine is leached in a fully automated plant by a two-step continuous process. Leaching residues, mixed with lead furnace slag, are treated in a shaft furnace. The recovered zinc fume is leached separately. In the near future, the leaching residues are to be treated by a wet process, developed in the Company's own laboratories. Purification of solutions is accomplished in two steps: antimony and zinc dust are added in the first one, only zinc dust in the second one for removal of cadmium. Electrolysis cells are partly of a conventional type. A new type of cell configuration was put onstream in October, 1969, planned output 60,000 tpy. Main features of the new cell rooms are the fully automatic pulling, stripping and replacing of the jumbo-size cathodes (immersed area 2.6 m2). Zinc cathodes are remelted in induction furnaces followed by in-line automatic casting and stacking machines.

Jan 1, 1970

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By Bradley Stoughton

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.-J. S.] INTRODUCTION. THIS paper gives the results : first, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows: 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such as, for example, the wear of railroad-rails, of steel and chilled-iron .rolls, car-wheels, etc. 2. These improvements seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example : A series of tests on cast iron

Nov 1, 1912

By G. W. Phelps

The field of industrial minerals is concerned with both sieve size and distribution of sub-sieve particles. A great deal of work has been reported on the techniques designed to provide information of this work. The term sub-sieve is here considered to include particular material that will pass a 325-mesh testing sieve. Plant men require rapid, precise and simple testing techniques that are, if possible, inexpensive with respect to equipment and manpower. A number of particle-size procedures have been developed, based on the Stokes equation for streamline movement of a particle of diam D, moving at velocity V through a liquid of viscosity n. 1 Particles are considered to be rigid, smooth spheres, completely dispersed at low concentration and moving at low velocity through the suspending medium with no slippage between particle and liquid. In particle size determinations the particle moves either from natural gravitational forces or those provided by centrifugal means. The diagram of Fig. 1 shows a spherical particle of density S and diam D moving downward at velocity L/T (or V) through a liquid of density So and viscosity n. The forces of gravity G (natural) or Gc (centrifugal) cause the particle to move through the liquid, thereby creating a viscous drag F or Fc. Within the streamline flow

Jan 1, 1967

By W. C. Maurer

A study of the mechanics of shear failure of rock under pressure has been made. The transition from brittle to ductile failure occurs when the friction along the fracture surfaces exceeds the shear strength of the rock. A machine has been developed for measuring both the shear strength of rock and the friction along rock fracture surfaces. In this shear machine, the fractures are forced along definite planes; as a result, the rock is stronger than in compression tests where the fractures choose the weakest paths through the specimens. Friction is composed of several forces: (1) the forces to slide irregulurities on surfaces over each other; (2) forces to shear some of these irregularities; (3) molecular attractions across the fractures; and (4) forces required to break bonds resulting from melting and welding at the tips of irregularities on the surfaces. Friction along rock fracture surfaces is not proportional to contact pressure as usually assumed; instead, it increases as the contact pressure raised to the 0.4 to 0.8 power. INTRODUCTION It is difficult to produce tensile stresses under the high compressive stresses present in the earth; therefore, in deep drilling and geological faulting, shear failure predominates. This shear failure mechanism is complicated because rock is a heterogeneous material containing pore spaces, microfractures, elastic discontinuities and other imperfections. A study of shear failure of rock under pressure has been made to obtain a better understanding of this complex mechanism. A machine has been developed and used to measure the shear strength of rock and friction along sheared surfaces. This machine has certain advantages over the compression test — shear properties can be measured under low normal stresses and shear stress and normal stress can be varied independently. The first part of this paper is a description of shear failure of rock under pressure. The role of shear strength and friction along fracture surfaces in the shear failure mechanism will be discussed. The second part consists of a description of the shear machine and a discussion of the shear strength and friction data obtained using this machine. It will be shown that shear strength depends upon the size of the stressed zone, and that friction does not increase linearly with contact pressure as usually assumed. Attempts are made to relate some of the new concepts to tectonic failure and to dril ling. SHEAR FAILURE IN ROCK TRIAXIAL TESTS The shear failure mechanism is illustrated by the triaxial test shown in Fig. 1. In this test, a cylindrical rock specimen is subjected to a confining pressure, PC, and an axial pressure, pa. These external pressures produce normal a and shear T stresses on inclined planes within the specimen equal to1 where 0 is the angle between the specimen axis and a normal to the inclined plane. Fig. 2 shows how triaxial specimens deform as the axial pressure is increased. The pressure is

Jan 1, 1966

By Roger C. Malan

The Monument Valley and White Canyon districts are in northeastern Arizona and southeastern Utah. Exploration and mining for uranium has been conducted in these districts since the late 1940's. In July 1965, ore reserves plus ore production at 174 properties were approximately 3.3 million tons of ore containing about 19 million pounds U3O8, of which about 10 per cent remained in reserves. The two largest mines, Monument No. 2 and Happy Jack, together account for about 45 per cent of the sum of production and reserves. Approximately half the deposits in these districts contain less than 1000 tons of ore. Nearly 5000 feet of Permian, Triassic, and Jurassic sedimentary rocks, mainly continental in origin, are exposed in these districts. All the important uranium deposits are in the Shinarump, the basal member of the Chinle Formation of Triassic age. The Shinarump lies on a widespread unconformity. It is composed of fluvial sediments, generally less than 100 feet thick, that were deposited by streams flowing from a source to the south. Most of the deposits are in an arcuate belt, convex to the west. This belt, 3 to 12 miles wide, extends from Monument Valley northward nearly 130 miles. It is along the western flank of the ancient Monument Valley-Monticello upland, an area that was slightly uplifted at the beginning and again at the end of deposition of the Shinarump. Erosion and subsequent reworking of the Shinarump sediments in the vicinity of this upland are postulated to have made possible the transportation, in solution, of the uranium contained in these sediments. The soluble uranium probably was carried by migrating ground water into sites favorable for precipitation in Shinarump beds bordering the upland. Thus, the original very small amounts of dispersed uranium in the early Shinarump sediments were accreted in the favorable belt where the accumulations of carbonaceous plant remains and their decay products provided a persistent reducing environment.

Jan 1, 1968

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 28 Montreal, Canada Sept, ?79 8 29 New York, N.Y. Feb, ?80 9

Jan 1, 1923

By B. C. Blake

IN general, billet-type or long slender ingots are used when it is desired to produce directly from the ingot in one conversion a product of medium or small cross-sectional area. They are designed to eliminate the blooming and billet-mill stages of the usual procedure. As used at Connors, they constitute a means of keeping a continuous rolling mill busy in the production of high-quality small rods, small angles, hoop stock, baling ties and concrete reinforcing rods without the need for a blooming or billet mill. They represent sound steel with the best surface that is commercially practical to use in the rolling of small continuous mill products.

Jan 1, 1947