Search Documents

By AIME AIME

OUR own Institute of Metals and Iron and Steel divisions cooperated with the Iron and Steel Division of the American Society of Mechanical Engineers, the American Welding Society, and the American Society for Steel Treating in a busy week at Cleveland. The morning sessions were held at the Hotel Cleveland and the afternoon ones at the Auditorium, where the metallurgical exhibition under the auspices of the American Society for Steel Treating not only occupied the arena of the Auditorium but completely filled the huge adjacent Annex. In the intervals of sessions the members thronged the exhibits but in the evenings the local attendance was so great that if the crowds had been any larger it would have been difficult to see the exhibits. With so many firms, both producers of metals and of equipment accessory to their production and use, it would be impossible to mention them -all and unfair to single out a few, since no two individuals' judgment would coincide as to relative interest and importance. In any case an exhibit is a thing to be seen rather than described, and these were well worth seeing.

Jan 1, 1929

By G. D. TRANT

HOT metal is commonly transported from the blast furnace to the open hearth by one or the other of two general methods: (1) by hot-metal ladles, usually in conjunction with a stationary mixer, or; (2) by means of mixer-type ladle cars, taking the place of both the hot-metal ladles and the stationary mixer. In both cases, the use of transfer ladles for charging the metal into the open-hearth furnaces is necessary. The American Rolling Mill Co. at its Middletown division, adopted hot metal practice on. June 2, 1928. The pig iron is produced' in a .blast furnace about 11 miles from the open-hearth furnaces, and is trans- ported in Pugh-type mixer cars having a capacity of 150 gross tons each. Three cars are in service and handle the delivery of hot metal to the pig machine and the open-hearth furnaces. The capacity of the blast furnace is 550 tons and casts are made every four hours.

Jan 1, 1929

By E. B. BESSELIEVRE

THE great work of Gorgas in stamping out yellow fever in Panama during the construction of the Canal was one of the chief factors contributing to the ultimate accomplishment of the task, two previous attempts having failed largely through the demoralization of workers by epidemics of contagious diseases. Mining camps, rapidly constructed during the boom days of the rushes to new fields, have been frequent sufferers from typhoid when, as so often used to be the case, little or no attention was given to bacterial examination of the water supply or to the method used for disposing of the sewage.

Jan 1, 1930

By Gene D. Clayton, Robert R. Dimock

A time-consuming and expensive preshearing program to minimize the adverse effects of blasting on slope stability at Kennecott Copper Corp.'s Ruth Pit in east-central Nevada has been eliminated in favor of down-the-hole, nonelectric delayed blasting which can produce a smooth wall effect and improve blast fragmentation. The new blasting approach resulted from a Kennecott engineering investigation aimed at improving the stability of the extremely variable rock conditions found throughout the pit by reducing the vibrational energy imparted to the walls with conventional bench blasts.

Jan 4, 1977

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By Albert L. Toenges

COAL mining technique progressed slowly until the advent of mechanized mining. The cutting machine was a forward step, but had only a limited effect upon improving the percentage of coal recovery. Previously, the physical fitness of the loaders and the total output of the miners fixed mine production. The miner was an independent contractor and supervision over his working place was superficial. Rising costs and the inroads of substitute fuels demanded increased output per man to lower the unit production cost. Therefore, the amount of coal loaded mechanically in underground bituminous mines has risen from 0.3 per-cent in 1923 to 7.4 in 1929, to 20.2 in 1937, and to 48.9 percent in 1943. When loading devices were introduced it became necessary to adapt them to existing systems of mining, or to alter the mining system to fit the machine. An increased amount of supervision was required as output depended upon proper operation of the machine rather than on the physical fitness of the individual.

Jan 1, 1946

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By C. W. Robinson

Transportation is the minerals business. Once upon a time the geologist, the engineer and later the metallurgist reigned supreme, but the leading role in mineral development today is the economist-especially the transportation economist. Obviously this trend is more important for large volume, low value mine-to-market movements of such commodities as iron ore, phosphate, potash, coal and petroleum. But, transportation is of sufficient importance to all mining activities to be included in forward planning. Civilization has been influenced by transportation developments to an extent little understood or appreciated. Although industrialists are capable of intelligent historical analysis of this phenomenon, too frequently they have failed to project, or anticipate those changes in transportation techniques which will influence the pattern of industrial growth.

Jan 1, 1971

By R. W. Heckel, R. L. DeGregorio

The DeHoff method of determining the size distribution of ellipsoid-shaped, second-phase particles has been applied to the spheroidization of cementite in a eutectoid steel. The surface area of Precipitates determined from the various size fractions in the distribution was correlated with surface-area measurements based on the number of intersected interfaces on a random lest line. The precipitate particles were found to be oblate ellipsoids with an axial ratio of about 0.90. The size distributions were found to be log-normal. A method is proposed whereby the shrinkage of small particles and growth of large ones can be determined from the experimental data. The experimental data are compared to previously proposed mathematical models describing diffusion-controlled kinetics and various types of interface-controlled kinetics. The experimental growth and shrinkage rates are considerably slower than those predicted by diffusion-controlled kinetics. The best fit is obtained for a model describing interface-controlled kinetics limited by the rate of formation of cementite at the growing interfaces where the interfacial reaction rate is proportional to the solute thermodynamic activity gradient across the surface. THE subject of spheroidization of second-phase particles has been considered previously by other investigators. Livingston1 has studied the precipitation of the cobalt-rich phase from copper alloys containing 0.7 to 3.2 wt pet Co. His results indicate that the average particle size increases as the cube root of the heat treatment time in accord with diffusion-controlled kinetics.'-' Komatsu and rant' in their studies of the growth of SiO2 in a dispersion-strengthened copper-silica alloy found that the initial growth of SiO2 proceeded by diffusion-controlled growth and later stages were limited by interface-controlled growth. The values of the activation energy obtained for the interface- controlled process led them to the conclusion that the process was limited by the dissociation of SiO2 at the shrinking interface. The transition from diffusion-controlled growth to interface-controlled growth was characterized by a particle size which varied with the heat-treatment temperature. It is also interesting to note that the particle-size distribution as found by Komatsu and Grant exhibits log-normal behavior when replotted on log-probability coordinates. Dromsky, Lenel, and Ansell9 have observed the growth of Al2O3 particles having a mean free path of about 1.5 to 13 µ. Their photomicrographs indicate that the Al2O3 particle sizes were larger than those observed by Komatsu and Grant. Dromsky, Lenel, and Ansell concluded that the Al2O3 coarsened by an interface-controlled growth mechanism limited by the solution of A12O3 at the shrinking interfaces. Bannyh, Modin, and Modin10 have studied the spheroidization of a eutectoid steel (0.83 wt pet C). Their spheroidization (tempering) treatments were carried out in the range from 210o to 700°C for times between 1.5 sec and 20 hr. Measurements of mean particle size as a function of time indicated a cube root of time dependence of size at 700°C, in agreement with previous analyses of diffusion-controlled kinetics.2°7 At lower temperatures, the time dependence was less than the one-third power. It is important to note that, although mathematical models of growth* considering particle-size distribution have been available, measurements of only mean particle size have been carried out. DeHoff11 has presented a quantitative metallography technique which is applicable to the determination of the size distribution of ellipsoids of constant shape. This method is applicable to both oblate and prolate ellipsoids of all ratios of minor to major axis and is based upon an extension of Saltykov's analysis12 of the distribution of spheres of varying size. DeHoff's analysis is based upon measurements of the minor axis of the particles on a random plane of polish in a unit area. This method provides a measure of the number of ellipsoids in various size ranges per unit area. As pointed out by DeHoff, such measurements may be used to obtain surface area and total precipitate volume data. Thus, the accuracy of the distribution analysis may be checked by comparison of the surface and volume

Jan 1, 1965

By E. J. Ripling

A NY mechanism proposed to explain hydrogen embrittlement in titanium and its alloys must, of course, be consistent with the experimental data that characterize this embrittlement. Unfortunately, however, the mechanical behavior of hydrogen-bearing titanium, at least a-ß titanium, has not been unequivocally defined. Lenning, Craighead, and Jaffee have clearly shown that hydrogen cmbrittles a-titanium by elevating its transition temperature, probably as the result of the formation of titanium hydrides. Therefore, in these alloys, hydrogen acts like at least one other interstitial contaminant, namely, nitrogen.&apos; On the other hand, ß-titanium has been shown by these same investigators to tolerate very large amounts of hydrogen without suffering severe mechanical damage.2 Mixing these two phases, however, to form the most important class of commercial alloys, the a-ß alloys, again results in severe hydrogen embrittlement, although the mechanism by which the embrittlement is produced is not of the same type as that which causes brittleness in a alloys. Ductility damage due to hydrogen increases as the strain rate is reduced in a-ß alloys, while embrittlement in a alloys increases as the strain rate is increased, since the latter is a transition temperature behavior. Steel, like the a-ß alloys, becomes more hydrogen sensitive at slow strain rates, suggesting that the mechanism producing the embrittlement in these two metals is similar. Brown and Baldwin&apos; described the hydrogen-produced ductility depression in steel as a function of testing temperature and strain rate by defining the slope of the two surfaces that produced the depression in a three dimensional chart, Fig. 1. One of these surfaces was given by the equations (de/de)4 > 0 (de/dT) < 0 [1] while the other was defined by the pair of equations Surfaces of the type given by Eq. 1 are suggested in two ways. One is an embrittlement mechanism wherein the diffusion rate of hydrogen is competitive with the rate at which the material is being deformed, as suggested by the planar pressure theory of Zapffe and his co-workers.&apos; The other is the diffusion controlled extension of Orowan&apos;s theory on delayed fracture in glass by Petch and Stables.&apos;&apos; Surfaces of the type given by Eq. 2 are also compatible with a mechanism of pressure build up in voids, according to de Kazinczy,&apos; since the solubility of hydrogen in the metal increases with testing temperature so that as the temperature is raised, the pressure in the voids is reduced. Kotfila and Erbin recently presented some data on the dependence of ductility on testing temperature and strain rate for the a-ß 3 pet Mn complex alloy at four different hydrogen levels.H Although data were presented for only three testing temperatures at three different strain rates, their results indicated that surfaces of the types defined in Eqs. 1 and 2 are produced in the alloy when the hydrogen level is sufficiently high—200 and 300 ppm—Fig. 2. Jaffee and his co-workers presented data on a number of different a-ß alloys which indicated the existence of surfaces of the type described by Eq. 2, but the ductility recovery at low temperatures as given by Eq. 1 was not found." In an attempt to aid in crystallizing this description of the ductility dependence of hydrogen-bearing a-ß alloys, tests were conducted by the author on a-ß titanium 140A with three different hydrogen contents. The tensile properties of two as-received rods and one vacuum annealed rod* were obtained over a range of testing temperatures and strain rates as shown in Figs. 3 and 4. Hydrogen analyses were made by the Battelle Memorial Institute on four pieces of the rod whose properties are shown as solid circles in Fig. 4. The hydrogen content of these pieces, taken at widely spaced intervals within the rod, were 280, 270, 289, and 270 ppm, indicating that the hydrogen content within a single as-received rod was quite uniform. One of the broken test pieces whose properties are shown in Fig. 3 as solid circles was also analyzed, and found to have a hydrogen content of 310 ppm. The analyses obtained on two of the vacuum annealed specimens were 92 and 170 ppm.

Jan 1, 1957

By Butler, P. B.

TRIPOLI is a rather unusual form of silica, which thus far has been found in commercially valuable quantities only in the neighborhood of Seneca, Mo., although there are numerous deposits of somewhat similar materials in several southern states. The latter have not, however, attained any position of real importance, due undoubtedly to definite structural limitations which have rendered them less suitable for the particular uses that have given tripoli its principal outlets. Raymond B. Ladoo, mineral technologist, says&apos;: "Since that time (1880-90) the term tripoli has with increasing definiteness been reserved for the Seneca material, and other siliceous materials of similar origin and physical properties."

Jan 1, 1928

By R. H. Ogburn

THE GROUND now being worked by the Fairbanks Exploration Co., near Fairbanks, Alaska, has been known to be gold bearing since 1901. In the early days it was worked by drift mining and other small-scale methods. In 1922, Hammond started prospecting the gold-bearing ground and obtaining options on the properties desired. Two years later the present Fairbanks Exploration Co. started taking up the options, and preparing to exploit the ground. For the prospect drilling Keystone drills were used, with holes at the points of equilateral triangles 600 ft. apart. Holes were also put down more closely spaced to determine the limits of dredging ground. In the first drilling casing was used to the bottom of the holes, but in later work the casing was put down only to the bottom of the thawed ground, and the rest of the hole put down without casing. The gold content was determined by panning, each 2 ft. of depth being determined separately. Where no casing was used the size of the hole was determined by using water to measure its volume. The greatest concentration of gold occurs at or near bedrock. All the gold-bearing streams head in one big dome. Gold, however, is not found clear to the head of the creeks, the pay being first found some distance downstream from the head.

Jan 1, 1933

By MERLE HOWARD GUISE

WHEN I was a boy I walked into Fairbanks in 1905. I was but a soft chechako, and arrived with blisters covering my feet, as a result of "mushing" the 400-mile trail on foot. Because of them, the display windows of the trading posts were first to catch my eye-dog and horse collars, harness and sled parts! And because of my enthusiasm for things adventurous, I looked long upon the prospectors&apos; gold pans, shovels, rifles, camp equipment, and what not. Today those windows are filled with motor car accessories, tires and repair parts; yes, even thermos bottles and vacuum cleaners! There were many chance meetings with little parties of prospectors in my youth, and it always set my blood to tingling. Sometimes it was a 70-year-old sun-baked son of the Arizona desert, wrangling his stubborn, faithful jenny away from some outfitting store, at others a shovel-ended poling b0at in northern Canada, \vith the partners and the dogs towing upstream along the bank, or an old sourdough, with tug-rope around neck and hand on the spruce sapling gee-pole, mushing along behind his two or three old, plodding malamutes, dragging a little Yukon sled piled high with rusty sheet-iron stove, pick and shovel, cross-cut saw and axe, rifle, bales of dog salmon, and other paraphernalia. These meetings envisioned the panning of old creek beds and draws in the search for as yet undiscovered pay-channels; they meant the toughest kind of work sinking a hole to bedrock in some far-away valley of promise; they suggested wood fires to thaw the frozen muck and gravel and crude windlass and hand-made tub to hoist the water and the mud; but loudest of all they spoke of Adventure.

Jan 1, 1929

By S. S. Arentz

An organized safety program has reduced accidents at Pioche because effort is first devoted to arousing and maintaining interest in safety, followed by training in accident prevention, assigning responsibility for the detection and removal of safety hazards, and finally, by keeping score through an adequate system of records. A health program is intergrated with the safety program.

Jan 1, 1950

By William S. Springer

A NEW preparation plant has been put in - operation to treat coal from the recently opened Concord mine, located about 15 miles west of Birmingham, Ala., by the Tennessee Coal, Iron & Railroad Co., a U. S. Steel subsidiary. The mine produces metallurgical grade coking coal from the American seam for use as coke in the company&apos;s blast furnaces at the Fairfield and Enseley works. The capacity of the operation is 1000 tons of run-of-mine per hr, approximately half of which is delivered to the by-product coke plant at Fairfield after beneficiation to metallurgical grade. The remaining portion of the mine run is rock and refuse removed during preparation. No boiler coal or other fuels are produced by this mine. Preparation of the coal is done both under- ground and on the surface. The underground primary crushing station removes some tramp iron, and screens and crushes the oversize, most of which is rock, to protect the main slope conveyor. The surface plant consists of a crushing and screening plant, large blending bins, a two- process washing plant, a water clarification and

Jan 1, 1950

By Zay Jeffries

A SURVEY of rare metals and minerals for the past year places uranium as one of two partners, the other being the neutron, in what historians will probably say is the greatest discovery in physics at least during the year and probably for a consider- ably longer period. The uranium atom has been made to divide into parts somewhat after the style of reproduction of the amoeba. When an amoeba divides into two parts, however, it produces two amoebae substantially alike and each substantially like the parent: furthermore, there is no considerable change of energy when this happens. When the uranium atom divides it yields other atoms such as barium and krypton with the complete destruction of the original uranium atom but with the liberation of a tremendous amount of energy. This will be discussed more at length later.

Jan 1, 1940

By C. Chamberlain

The Telfer Project, Australia&apos;s newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

By C. R. Breck

THERE has been a running discussion over the past several years with respect to the life and adequacy of our natural gas reserves. Some of the experts agree on one phase of the subject at least-that eventually it will be necessary to augment deliveries of natural gas in the northern markets by the development of a more or less comparable synthetic gas made from coal. The purpose of this paper is to point out: 1. It may be later than a good many people think-the demand for addi¬tional domestic and commercial pipeline gas in at least one section of the North will probably be felt rather keenly before an adequate synthetic pipe¬line-gas project, developed on economic lines, could be completed, even if initiated in the near future. 2. The evidence is considerable that such a project would be technically sound and economically self-supporting, although the margin of profit at first might be so small and the magnitude of an economic enterprise so great -that financing would be impossible without Government aid in some form or other. The part of the country referred to is the heavily populated section in the northeast of the United States. To simplify an examination of the situa¬tion, let us take the potential marketing areas within range to the north and east of the three pipelines: 1. Tennessee Gas Transmission Co. as it enters Erie County, New York state. 2. Texas Eastern Transmission Corporation just before the tap that sup¬plies the general Philadelphia area. 3. Transcontinental Gas Pipe Line Corporation as it enters the state of New Jersey. The sources of gas for these three pipelines are in Texas and Louisiana. The ultimate maximum combined capacity of the three lines at the points stated is approximately 1,200,000,000 cu ft per 24 hr at the maximum load factor probable of attainment in normal operation. The areas supplied by the three lines north and east of the points stated, or assumed as eventual markets, are: 1. Central New York state, from Buffalo to Albany (both inclusive).

Jan 1, 1953

By Mitchell, Edmund I.

VARIOUS suggestions as to proper fees for engineering services have been put forth by individual practitioners and by the American Institute of Consulting Engineers, the Connecticut Society of Civil Engineers, the Iowa Engineering Society and the Mahoning Valley (Ohio) Engineers, for the guidance of both the engineer and his client. The American Institute of Architects also has a schedule of minimum charges (revised 1908). So far as can be determined, however, the four national societies representing civil, mining, mechanical and electrical engineering have never given consideration to this question. An examination of technical periodicals published during the past decade shows that these schedules make provision for three methods of charging; i.e., (A) a percentage of the cost of the completed project; (B) a per diem rate; and (C) a fixed sum. Suggested minimum charges are as follows:

Jan 1, 1921