Search Documents

By W. W. Eckles

This paper is presented as a suniniary report of the use of well gas composition correlations obtained from mass spectrometer recordings as a means of identification and determination of reservoir continuity. Conventional methods for detecting composition differences are en-pensive, elaborate, and difficult to obtain. This excludes the use of extensive composition data for most applications. During recent years the mass spec-trometer has come into general use as an analytical tool in petroleum refineries. The use of mass spectrometer composition patterns ir~ characterizing or "finger-printing" the produced gas from a reservoir, presents a novel method for correlatitlg gas samples from well to well. The mass spectrometer provides a trace similar to an electric log. having peaks which represent the abuntlnnce of certaitz hydrocarbons in the well gas sample. Without going further into the detailed analysis the idea has been advanced that these traces or patterns could be used as a means of identifying a particular natural gas. This theory has proven to be essentially correct. The mass spectrometer pattern method is simple and cheap as COi?7pared to other standard methods. It greatly facilitates the solution of reservoir and geological problems in which correlation of well gas Com-positions is a factor. Specific field applications have been made. This paper concerns the results obtained in 465 individual gas analyses from 35 fields and 77 res- ervoirs. In a number of cases it has been found that such data have been extremely valuable in the determination of reservoir continuity. In at least one case, the method was a valuable contribution in tracing a reservoir from sand to sand in a coinplex fnulted field involving n11rnerous gas reservoirs. Field applications are presented to illustrate the possibilities of the method at the present stage of developnient and to stimulate the ernployrnent of this new approach by geologists and petroleum engineers in the industry. INTRODUCTION Identification of producing horizons and the determination of reservoir continuity are often a problem in those areas where dome structures and highly faulted sands are encountered. To complicate the picture further, there may be numerous sands, one on top of the other which dip and diverge in different directions. Even though it may be possible to develop some solutions to the preceding problems on the basis of the geological and reservoir data on hand. it is readily recognized that substantiating data based on independent methods would he extremely valuable. It has been found through field studies that correiation of well gas composition can be used to advantage in the geological and engineering study of a complex reservoir identification problem. METHOD FOR COMPARISON AND CORRELATION OF WELL GAS SAMPLES Since a large number of well gas samples are required in a gas identification or reservoir con- tinuity problem, it is necessary that a method of analysis be employed which can detect differences in composition readily and inexpensively. Although detection would be possible by means of low temperature fractional distillation (POD) analpsis, the method requires a relatively large sample and is comparatively slow and expensive to run. The mass spectrometer affords an inexpensive and precise analysis of small well gas samples taken at the surface which are about 1/300 as large as a POD sample. These samples can be obtained by regular field personnei and shipped to the spectrometer for analysis. It is, therefore, a practical approach to the problem. A typical record from the mass spectrometer is illustrated in Fig. I. The peaks on the record represent the abundance of ions produced from the different hydrocarbon molecules making up the gas sam-ple. In well gas comparisons only five peaks are employed, since the other peaks are formed from the same gas molecules and furnish no additional information. The five peaks used represent the abundance of methane, propane, ethane, butane and heavier, and oxygen. They are referred to respectively as the 16, 29, 30, 43, and 32 peaks. The oxygen peak is used to correct for air content in

Jan 1, 1958

By H. R. Peiffer

Hardening of soft metals can be accomplished by dispersing finely divided hard particles in them. The dispersing of finely divided alumina in silver in the presence of oxygen yields a high strength material which is unusual in that its mechanical properties above the melting point of the continuous Ag-O alloy matrix are similar to other solids. The tensile strength is studied for two of these alloys, one of which contains 15 pct by weight alumina and the other 20 pct by weight alumina. The average fracture strengths above 960°C of these alloys were found to be 0.4 x106 dynes per sq cm and 3.8x106 dynes per sq cm respectively. The strengths appenred to be independent of temperature above 960° C. The creep behavior of the 20 pct alumina material was studied above 960°C. The initial creep rate, 6 , of this material can be represented by where s is the applied stress and E the activation energy for the process. This energy is of the order of 1.7 to 2.1 ev. HARDENING of soft metals by the addition of finely divided, hard particles has resulted in the production of materials with excellent creep resistance and with inhibited recrystallization.' It has been demonstrated that such composites have useful strength up to temperatures very near the melting point of the soft metals, but one might expect that the strengthening by the dispersed particles ceases to be of importance above the melting point of the softer phase. This, however, is not so.2 In this paper the strengthening of a liquid Ag-O solution by the presence of dispersed alumina is discussed and experimental data concerning the mechanical properties of such a material at temperatures above 960°C presented. EXPERIMENTAL PROCEDURE Specimens were prepared using powder metallurgical techniques. Finely divided silver oxide was mixed in the appropriate proportions with "Linde B" alumina. For these experiments the specimens contained 15 or 20 wt pct alumina in pure silver.* These alloys were used in these experiments since they were the ones that could be handled readily enough to yield experimental data. Silver oxide was used in preference to silver because it is readily available in a very finely divided form and because the presence of excess oxygen in the silver is important to the properties2 of the material. The powders were mixed wet, using alcohol as the medium, in an ordinary food blender until a uniform mixture was obtained. They were then dried and heated to reduce the silver oxide to silver. Only a fraction of the finely divided silver remains unoxi-dized upon removal from the oven since the finest particles of silver oxidize immediately upon contact with air. The remaining fine silver served as a binder during pressing. The mixture was then pressed at 20 tons per sq in. into shoulder-grip (reduced section 1/4 in. by l/4 in. by 1 1/4 in.) and rectangular bar specimens (l/4 in. by 1/4 in. by 2 in.). The green specimens were heated very rapidly in a globar furnace to 1000°C, held at temperature untic they had reached theoretical density and then furnace cooled. The strength of the two compositions at temperatures above 960 °C was determined by pulling shoulder grip specimens inside a furnace mounted on a tensile machine. Specimens were gripped by means of wires wrapped around the shoulders of the specimen. Temperatures were measured by means of a chro-mel-alumel thermo-couple placed in the vicinity of the specimen. Control of temperature (within ±°15C) was accomplished by means of a Weston Recorder-Controller. Before loading, specimens were held at temperature for approximately 15 min in order to insure uniform specimen temperature. The low loads were measured by a special load cell designed by Baldwin Lima Hamilton. All testing was performed on a FGT testing machine of the same com-pany. Creep studies were performed in bending utilizing rectangular specimens of the 20 pct alumina alloy. Specimens supported at both ends by knife edges of inconel were placed in a globar furnace, heated quickly to temperature, and the deflection of the beam measured optically as a function of time. The weight and size of the specimen were predetermined and the maximum stress on the beam calculated from

Jan 1, 1962

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

By John E. O’Rourke, Kevin M. O’Connor, Pamela H. Rey

INTRODUCTION The resurgence of coal mining activity in the United States, brought on by the spiraling costs of fossil fw1 energy in the Seventies, has come at a time of intense public concern for the quality of the environment. Notwithstanding pressure on our economy to develop alternate sources of fue1 energy to the import of oil, the legislatures of several states have reacted to public concern over the environment by passing strict regulations aimed at con- trolling the subsidence effect s of underground mining. Agencies of the federal government charged with assistance to the mining industry, including the Department of Energy and the Bureau of Mines, have sponsored a number of instrumentation and field measurement projects aimed at the development of subsidence prediction models that can aid the mine operator's task of subsidence control. There are good empirical models developed in Europe for subsidence prediction, but they were made possible by a large body of mining-induced subsidence data collected there over a long period of time. No com- parable subsidence data base exists in the United States, and consequently empirical modeling of subsidence is not a realistic approach for our near term needs. Moreover, the geologic and topographic diversity of the several coal regions in the United States is expected to necessitate the development of several empirical models, each one expected to be relevant to its own region. Because of the time and costs that are likely to be involved in an empirical modeling approach, it is considered more expedient and cost effective to develop a general, mechanistic model for subsidence prediction purposes. In order to develop such a model, it is necessary to investigate and quantify the mechanics of the subsidence process from the mine level up to the ground surface. The series of projects discussed in this paper are designed to achieve this objective and include the following work: (1) the identification of geotechnical instrumentation that will pro- vide mine level overburden and surface subsidence data. (2) a field demonstration of selected instruments, and (3) documentation of case histories for complete subsidence mechanics, using the demonstrated and preferred instruments. An identification of feasible instrumentation and monitoring techniques was completed by Woodward-Clyde Consultants (WCC) in 1977 (O'Rourke and others). This paper discusses a demonstration of those instruments at a mine in Utah, and at two subsequent projects, currently underway at longwall mines in Colorado and West Virginia. 'he latter two projects when complete will provide documented case histories of subsidence mechanics. The process of optimizing subsidence instrumentation and monitoring techniques to the conditions encountered during installation and monitoring for these underground mines is shown to be an evolving one, and one which has had some notable successes to date. INITIAL DEMONSTRATION The initial design and demonstration of selected monitoring systems was carried out at the SUFCO No. 1 mine, near Salina, Utah. The instrumented panel was approximately 152 m wide. 640 m long. and was 290 m to 320 m deep. The mined height of coal. seam averaged 2.4 m. The mining method was room and pillar using continuous mining machines. This method allowed some monitoring of the supported condition during development, and eventually allowed monitoring of a caved system when both chain pillars and room pillars were extracted on retreat. The two instrument systems shown on Table 1 were selected from the earlier feasibility report for demonstration at SUFCO No. 1. Collectively, the two systems, one for a fully-supported mining method and the other for a fully-caved method, incorporate most of the instrumentation to be found within all five systems listed in the earlier feasibility report. The instrumentation includes surface, subsurface and mine monitoring installations. All of the SUFCO instruments selected to meet the specifications of the general instrument types listed on Table 1 were manually operated. That is, data from the installed system could only be obtained while a person was there to physically observe or operate the system readout. Automatic data recording equipment was available for some installations, but the objectives were to keep the systems as simple as possible for the demonstration project. A complete description of the surface, sub- surface and mine level instruments, and the demonstration project results are given in WCC (1982), and selected features are discussed in this paper.

Jan 1, 1982

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined in part for the sgstem Gd-Fe. Seven intermetallic compounds have been found at compositions corresponding to the following Gd-Fe ratios; 2:3, 1.2, 1:3, 2:7, 1:4, 1:5, and 2:17. The GdFe, com-pound has a congruent melting point above 18000C, whereas all of the remaining compounds melt incongruently, A eutectic exists at 13 wt pct Fe at a temperature of 860°C. ALTHOUGH an increasing amount of information is becoming available on the metallurgy of pure rare earth metals, relatively few studies have been made on alloy systems of the rare earths with the transition metals; iron, nickel, and cobalt. Even less data are extant on gadolinium alloys although it could be expected that such alloys might possess interesting structural and magnetic properties. In this paper, we report investigation of the gadolinium-iron alloy system. Studies on systems containing nickel and cobalt will be presented in subsequent papers. Previous data on gadolinium-iron compounds have been reported by Endter and Klemm1 and Jep-son and Duwez.2 Both reports agree on the existence of the GdFe2 phase, which crystallizes with the C-15type structure (face-centered cubic). This is in accord with results of the present work. EXPERIMENTAL The gadolinium metal used was prepared by met-allothermic reduction of high purity gadolinium fluoride. A typical analysis of the metal thus produced indicated the principal impurities to be oxygen, 0.24 pct, and tantalum, 0.2 pct. The iron metal used for alloying was a reagent grade material. Alloys were prepared by arc melting mixtures of the respective metals. Appropriate quantities of the two component metals were carefully weighed, blended and compacted. The compacts were then melted in an arc furnace consisting of a water-cooled copper hearth plate and a water-cooled tungsten-tipped counter electrode contained in a brass vacuum chamber. The furnace was evacuated to an absolute pressure of less than 1 with the leak rate established as being less than 20 per min. The furnace was then back-filled to a pressure of 25 mm of Hg, with a 75 pct He-25 pct Ar mixture. Arc melting at 25 v and 300 amp was maintained for about 30 to 60 sec until the entire visible area of the sample became molten, by which time surface tension had drawn the molten metal pool into a large bead. After allowing the furnace to cool, the alloy button was inverted and the melting process repeated. A series of melts was made covering entire composition ranges from 100 pct Gd to 100 pct Fe. All samples were examined metallographically in the as-melted condition. As the phase diagram became rationalized, and differential thermal analysis had given indications of temperature arrests, annealing was carried out in vacuo or in argon. Generally, compositions containing more than about 60 pct Gd were heat treated at 750°C and alloys containing less than this quantity of gadolinium were annealed at 1000°C. Prolonged annealing times were of the order of 100 to 200 hr. Metallographic examination was repeated on the annealed materials. Although little material loss was noted during alloy preparation, chemical analyses were made on all specimens prepared. The following standard, analytical techniques were used. Samples were dissolved in hydrochloric acid; insoluble material was filtered off, ignited and fused with potassium pyro-sulfate. The cold melt was leached with dilute acid and the solution thus obtained added to the main sample solution. Gadolinium was always determined gravimetri-callv as oxide from oxalate ignition. Iron was removed from an aliquot sample by electrolysis on a mercury cathode at approximately six volts. Gadolinium in the iron-free electrolyte was then precipitated as oxalate which was subsequently ignited to oxide. Iron was determined volumetrically in an aliquot solution by reduction with stannous chloride fol-

Jan 1, 1962

By W. S. Cavender

The Round Mountain mining district, Nye County, Ne- vada, was discovered in 1906 on claims owned by Lewis D. Gordon. Initial mining operations uncovered gold veins of spectacular richness, and within a few days of discovery, Gordon sold his controlling interest for some $87,000. From this sale emerged the Round Mountain Mining Co., predecessor of Nevada Porphyry Gold Mines, Inc., the latter destined to become the major property owner in the area. Vein mining in the district continued sporadically into the early 1930s, yielding 9.3 Mg (330,000 oz) of gold plus substantial silver credits from approximately 626 kt (690,000 st) of ore. In addition to the lode deposits, the early miners recognized the placer potential in the alluvial fan material accumulated around the west and north sides of Round Mountain itself. Intermittent placer operations were carried out for a number of years, and in the 1940s and 1950s, Round Mountain Gold Dredging Co. worked the placers under a lease from Nevada Porphyry Gold Mines. The last placer operation terminated in 1959 when it, like some of its predecessors, proved uneconomic. Total placer production for the district is estimated at 3657 km (4 million yd) of gravel containing 59 Mg (210,000 oz) of gold and possibly 2.0 to 2.3 Mg (70,000 to 80,000 oz) of silver. Round Mountain is a small hill situated on the east flank of the Toquima Range in central Nevada. The hill is com- posed of relatively flat-lying Tertiary rhyolitic ash flow tuffs, which overlie Paleozoic metasediments and Cretaceous granites. Throughout the surrounding Round Mountain mining district, most of the known gold ores occur in the tuffs, although the metasediments and granites are also mineralized. Mineralization is structurally controlled, principally by a series of northwest-trending shears and shattered zones. Vein, stockwork, and disseminated ores occur, usually containing simple quartz-pyrite-gold mineral assemblages. The gold itself is electrum, having a silver content of 30% to 40%. In September, 1967, Elwood Dietrich, a prospector and mine promoter, obtained a purchase option on the 4452 ha (1 1,000 acres) of mineral rights held at Round Mountain by Nevada Porphyry Gold Mines. The original option had a buy-out price of $1 million and was established through Dietrich's friendship with officers of Nevada Porphyry. In April, 1968, Dietrich conveyed his option to Ordrich Gold Reserves Co., a partnership created by a group of west coast investors, mostly employees of the airline industry. There- after, Ordrich invested considerable funds in trying to test and develop the property, but soon recognized the need to seek financial and technical support from the mining industry. In December, 1968, Dietrich contacted Wayne Cavender, then Regional Geologist, Southwest, for Copper Range Exploration Company (CRX) in Tucson, Arizona, and made a data presentation. Shortly thereafter, Cavender was appointed Manager of Exploration and Chief Geologist for Copper Range Co. (parent company of CRX), New York City, and he asked C. Phillips Purdy, CRX Regional Geologist, Northwest, to make an initial property examination. Purdy's one-week field study took place in March, 1969, and resulted in a recommendation that CRX pursue its investigation of the property. The presence of low-grade gold mineralization in both the alluvial gravels and in the bedrock was verifiable, but the placer was deemed to have the greater immediate economic mining potential. At that time, gold was in the $1.41/g ($40 per oz) price range. Working from Purdy's information, Cavender decided to attempt acquisition of the property, and the first in a long series of negotiations was initiated with Ordrich. Basically, CRX felt that the placer had a promising potential for several reasons, including (I) past operators had recovered free gold but not the gold contained in the pebble fraction of the gravels; (2) past operations appeared to have been ineffectively designed or managed and not costefficient; and (3) the price of gold appeared to be poised for an upward move. Negotiations with Ordrich were prolonged and difficult, with CRX competing against several ma* mining companies, but finally an agreement was reached, effective June I, 1970. Gold was then back to $35. It is believed that, in

Jan 1, 1985

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,' the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson's investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.'s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By H. Kahata, I. Iwasaki, Y. Takahasi

A combined process of segregation roasting-flota-tion or magnetic separation was developed to recover nickel from lateritic iron ores and oxidized nickel ores. An ore was mixed with a halide, such as sodium or calcium chloride, and a solid reductant, and roasted, whereby the nickel content was segregated out as discrete metallic particles. Either by magnetic separation, or by flotation using a sulfhydryl collector together with a heavy metal salt as an activator, the metallic nickel could be concentrated, Effects of such variables as the types and amounts of the halide and solid reductant addition and of the roasting conditions were extensively investigated. The concentration results on several types of ores from Japan, the Philippines, and New Caledonia are presented. Laterite is a residual product of rock decay in tropical and subtropical regions, and consists mainly of hydrated oxides of iron and alumina. Those derived from serpentine sometimes become enriched in nickel, cobalt, and chromium contents. Oxidized nickel ores are of the similar origin, but their nickel as well as silica contents are higher due to gamierite-type silicates. Apparently, nickel enrichment is more pronounced in the transition region between the surface layer of iron laterite and the underlying serpentine. Iron laterites often contain over 50% iron, and their reserve is reported to exceed 22 billion tons, corresponding approximately to 20% of the world iron ore reserve.1 It is readily apparent, therefore, why the iron laterites have attracted much attention of the steel industry as a potential source of iron ores. Numerous attempts to remove nickel and chromium as byproducts, have been reported in literature.' Worldwide discoveries of high-grade iron ore deposits in recent years have inevitably lessened the interests in iron laterites. However, in view of the tremendous potential for their gross value and supplies of nickel, cobalt, chromium, and alumina along with iron, the problem remains as a challenge. Much of the chromium in laterites is present in the form of relatively coarse particles of chromite, and various classification methods have successfully been applied for its removal.2,3 The nickel, however, is intimately associated with limonite, and ordinary concentration techniques are totally ineffective. Much attention has, therefore, been given to hydro-metallurgical or pyrometallurgical means. Yet, all the known processes appear to have limitations either economically or for the use of products as iron raw materials due to a high residual content of nickel. Some attempts have been made to pre-roast laterites or oxidized nickel ores, particularly with sulfidizing agents, and to remove nickel either by magnetic separation,' or by flotation.4 It is apparent that any such concentration process would require grain growth of nickel during roasting for effective separation. Oxidized copper ores are reported to be concentrated by the segregation roasting-flotation process,5 in which the ores are roasted with a chloridizing agent and a carbonaceous reductant in order to promote the growth of metallic copper through repeated cycles of copper chloride volatilization and its reduction on the solid reductant surfaces. Examination of a vapor pressure-temperature diagram of various metal chlorides indicates that a separation of nickel from iron may be effected by a similar process. In fact, the segregation roasting of laterites was reported to increase the extraction of nickel by the ammonia leach process, as compared to the ordinary reduction roasting.6 In the present article some of the preliminary experimental results of the segregation roasting, followed by either flotation or magnetic separation, on laterites and oxidized nickel ores are reported. The effects of various parameters in the roasting as well as in the concentration steps are discussed. MATERIALS AND METHODS An oxidized nickel ore from Thio, New Caledonia, and three laterites from Homonhon, the Philippines, Wakasa and Miyagawa, Japan, were selected for the

Jan 1, 1967

By R. Simon

The sources of energy dissipation for concentrated loadings on rock are considered in an attempt to account for the experimentally measured magnitude of the work required to break out a unit volume of rock from the free surface of an essentially semi-infinite medium. It is concluded that most of this work probably represents the elastic strain energy developed by the loading in a much larger volume of rock beneath the loaded region than the volume of the rock fragment broken out to the side of the loaded region. This strain energy is largely dissipated in the form of stress waves generated by the high rate of unloading produced by the propagating cracks. The energies associated with the formation of the new surfaces of the cracks and with the stress waves generated directly by the loading process are computed to be negligibly small. Possibilities for improving the utilization of energy to drill rod. subject to the geometrical limitations imposed by down-hole operation, are discussed. It is pointed out that any such possible improvements would probably have to be differential ones, since each rock configuration of more favorabIe loading geometry that can be created down the hole is accompanied by a complementary configuration of less favorable loading geometry. INTRODUCTION Dislodging each cubic inch of rock from the bottom of the hole by the action of a bit requires the expenditure of an amount of energy that varies from approximately 5,000 in.-lb to approximately 100,000 in.-lb, depending on the hardness of the rock, or, more technically, upon its fragmentation strength.1 In this paper we will discuss (I) why the energy expended in drilling is so large, (2) what happens to this energy upon completion of the drilling process, and (3) what are the possibilities for reducing the magnitude of the energy required to drill rock. DETERMINATION OF ROCK DRILLING ENERGY The volume of rock removed per unit time from the bottom of a hole of diameter D is evidently (7/4)D2R, where R is the rate of penetration of the bit. If P is the rate at which work is done by the bit on the rock at the bottom of the hole, the energy required to break out a unit volume of rock is given by: Ev =(4/p) P/D2R............(i) For rotary drilling, of either the rolling-cone or drag-bit varicty, P = 2pLN, where L is the torque resistance to rotation at the bottom of the hole and N is the rate of rotation of the bit. L is essentially the same as the torque measured at the rotary table only when drilling in shallow holes. The energies expended in rotating the drill string against the frictional resistance of the walls of the hole and and against the viscous drag of the drilling fluid are extraneous to the subject under consideration, although these may be much greater in magnitude than E, when drilling in a deep hole. For percussion drilling, P = fE where f is the percussion frequency and E is the work done on the rock per impact. The latter quantity can be both computed and measured for a percussion drilling machine. 2 (Under satisfactory drilling conditions, defined in terms of ranges of numerical values of certain dimensionless parameters, E is only 30 to 50 per cent less than the impact energy of the striker.2) Alternatively, E, may be measured directly by dropping chisels shaped like bit edges, backed by rigid weights, onto the surfaces of laboratory rock samples of effectively semi-infinite extent. Under these circumstances, essentially all of the impact energy is converted to work done on the rock, and the relationships among volume of rock broken out, chisel shape, impact energy and indexing distances can be obtained.3 The values of the energy required to break out a unit volume of rock under favorable circumstances are substantially in agreement for rotary drilling, percussion drilling and drop testing at atmospheric pressure. The energy per unit volume is a quantity of the order of magnitude of roughly twice the com-pressive strength of the rock as measured by a uniaxial loading test. The phrase "order of magnitude" in this paper means from about 1/3 as much to 3 times as much; i.e., the energy per unit volume may range from roughly the same up to several times

By R. B. BRINSJIADE

THE following is an attempt to form a formula by which a mine call be quickly evaluated, after all pertinent physical data have been collected from observations on the ground by a competent mining engineer. ASSUMPTIONS. Let G = price to be paid for the mining property. M = cost of developing the mining property to yield y tons of ore daily. P = cost of suitable plant to treat y tons of ore daily. p = value of said plant when the mine has.been exhausted. C = total fixed capital investment. W = working capital investment

Jan 1, 1908

By Cyril Stanley Smith

Jan 1, 1949

By Cyril Stanley Smith

Jan 1, 1949

By C. M. Fellman

AVAILABLE data for the first nine months of the Year indicate that accident occurrence in metal mining was well on its way to an all-time low for 1939. However, the relatively rapid pickup in mining production in the fall will be likely to boost both accident occurrence and also accident rates. Results of the National Safety Competition for 1938, the fourteenth of its kind conducted by the U. S. Bureau of Mines, were published in August, 1939. W. W. Adams, statistician of the bureau, states that "with 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost- time accidents occurred during the con- test year." The National Safety Competition provides a means whereby mines and quarries may engage in active competition to stimulate their safety programs. Companies in the contest can compare their records with those of similar plants operating elsewhere and thereby determine to what extent their safety programs are successful. The Joseph A. Holmes Safety Association gave over 150 awards for safety performance in the mineral industries in 1939 and a remarkable phase of these awards was the considerable number given to individual miners who had worked fifty or more years without sustaining a lost-time accident.

Jan 1, 1940

By K. Sassa, I. Ito

The dynamic principal stresses induced within rock by an explosion under con fined conditions are analyzed for the case of blasting with one free face by applying the values of measured radial displacement, particle velocity and so on to equations derived from the theory of elasticity. The dynamic stresses on the free face are also calculated from the strain measured by wire strain gauges affixed on the free face. Some results obtained are briefly: 1) The maximum stress on the free face appeared at the intersection between the free face and the burden, and its magnitude was about twice as large as the magnitude of the tangential tensile stress imparted by the incident stress wave within the range related to the breakage by blasting. 2) The maximum value of the compressive stress near the free face was decreased due to the existence of the free face, while that of the tensile stress was increased. 3) At any point near the free face, the directions of the principal stresses in the r? plane using spherical coordinates with the origin at the center of the spherical charge, changed with time except in the direction of the burden. However, at another point near the explosion point where the principal stresses were mainly those stresses caused by the initial longitudinal wave, the directions of the principal stresses coincided with those of the coordinate used. 4) The maximum value of the tensile stress in the F direction was larger than those in the re plane at and near the free face. 5) The tensile stress caused by the Hopkinson effect appeared only near the burden. 6) It is presumed from the results of stress analysis that radial cracks will be produced in the rock mass near an explosion point, but with the approach of the free face, the directions of cracks curve towards a direction parallel to the free face. INTRODUCTION In order to investigate the mechanism of rock breakage by blasting, it is considered to be very im- portant to know how the stresses are generated and distributed within the rock by explosion of a confined charge. As part of a research program concerning the mechanism of rock breakage by blasting, the authors have already published papers on the detonation pressure produced at the inner surface of the charge hole1 and on the behavior of the dynamic stresses within rock caused by an explosion in the case where no free face existed.' In this study the dynamic stresses on and near the free face have been investigated for the case of blasting with one free face. The mechanism of rock breakage in blasting is discussed in the light of these studies.

Jan 1, 1967

By J. E. Tobey

BECAUSE of the wide-spread publicity given to Nylon yarn as being made from ?coal, air, and water,? the general public has become conscious of the nonfuel uses of bituminous coal. Some of these uses are as filler for fertilizer, carbon for the absorption of orders, for water supply, and for the bedding of cattle. Spectacular as are these accomplishments the fact is that only a small amount of coal is used for nonfuel purposes. It is on the utilization of coal as fuel that the industry depends. Practically all the coal mines for years to come will be used for making coke for the generation of heat. Recently much attention has been paid to the significance of ash in coal. Another study worthy the interest of metallurgists in the iron and steel industries if that of Dr, Lowry of the Carnegie Institute of Technology relative to the percentage of sulphur in coal and coke.

Jan 1, 1941

By H. C. Babbitt

The Effect of Arsenic.—A question involving the temperature of precipitation of ammonium phospho-molybdate, which was brought to my attention some time ago, led to the following experiment :*

Jan 1, 1893

By Nagel, Theodore

USE of oxygen in metallurgical operations was investigated by a committee of unusually able engineers more than ten years ago. A record of their work appeared under the title "The Use of Oxygen or Oxygenated Air in Metallurgical and Allied Processes," Serial 2502, Report of Investigations, U. S. Bureau of Mines. Shortly thereafter the A.I.M.E. published "Use of Oxygenated Air in Metallurgical Operations," based on a symposium at the New York meeting, February 1, 924. Quoting from the Bureau of Mines report In view of the many recent developments in oxygen manufacture, and considering the increasing cost and decreasing quality of our raw materials, the Bureau of Mines has taken the matter of the application of oxygen or oxygenated air to the metallurgical centers for consideration and has appointed an advisory committee to study the problem.

Jan 1, 1935

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By AIME AIME

A REGULAR meeting of the Executive Board 'of American Engineering Council was held in the Onondaga Hotel, Syracuse, N.. Y., Feb. 14, 1921, with the president, Herbert Hoover, presiding. Reports of committees were presented and acted upon as follows: ENGINEER ON INTERSTATE COMMERCE COMMISSION The second meeting of the Committee was. called because it was represented to the Committee' on Pro¬cedure that the American Society of Civil Engineers, the American Association of Engineers, and the Ameri¬can Institute of Consulting Engineers were anxious to have President-elect Harding appoint an engineer to fill one of the vacancies on the Interstate Commerce Commission. The representative of The American Society of Civil Engineers agreed to endorse the recom¬mendations- of American Engineering Council, and the Committee on Procedure prepared and sent a letter to the President-elect, a - copy of this letter being sent to each member of the Board. No names were suggested. . The appointment of an engineer on the Interstate Commerce Commission was approved and the Board, after approving the action of the Committee 'on Procedure in writing the President-elect, voted that, if requested, the Committee on Procedure submit a list of not less than six names for the appointment of an engineer on the Interstate. Commerce Commission.

Jan 1, 1921