Search Documents

By E. N. Mazza, H. S. Kalish

The effect of sintering types 302, 3028, and 430 stainless steel powder compacts in hydrogen and dissociated ammonia was investigated. It was found that sintering in dissociated ammonia resulted in as much as 0.5 wt pct increase in the nitrogen content of stainless steel even though the dissociation of the gas was complete. Sintering in hydrogen, on the other hand, reduced the nitrogen content of the stainless steel to less than 0.01 wt pct. In the case of the 302-type stainless steel, the low nitrogen content resulted in a material that was largely ferritic, whereas the high nitrogen content rendered the material fully austenitic. Sintering in dissociated ammonia resulted in lower density, generally lower tensile strength, less ductility, and higher hardness than sintering under equivalent conditions in hydrogen. The reduction of oxides on both stainless steel and iron particles was found to be effected by hydrogen partial pressure in the sintering atmosphere. Compacting pressure was found also to effect oxide reduction during sintering. DISSOCIATED ammonia often is used as a substitute'.' for hydrogen in sintering and in annealing, since economic advantages sometimes can be obtained by such a substitution. In addition, anhydrous ammonia contains very little impurity. Thus, dissociated ammonia gas is very dry whereas tank hydrogen often must be freed of oxygen and water vapor prior to use in many applications. The sintering of stainless steel powder compacts as well as bright annealing is well recognized as requiring a hydrogen atmosphere and for the foregoing reasons dissociated ammonia is frequently substituted. It has generally been overlooked, however, that the nitrogen in dissociated ammonia might have an important effect on the sintering process and on the properties of stainless steel compacts. Considered an inert gas in many applications, nitrogen, on the other hand, is very reactive with cer- tain metals. Dissociated ammonia could not be used for hydriding zirconium or titanium. Nitrogen reacts with columbium, tantalum, chromium, uranium, thorium, and many other active metals. Iron and iron-base alloys are, for the most part, inert in nitrogen but there are many borderline cases. It has been reported that stainless steel stabilized with columbium or titanium should not be sintered in dissociated ammonia.3 olybdenum has been reported as reacting with dissociated ammonia to a minor extent.' Although most of the reactions with iron-base alloys are attributed to the action of un-dissociated ammonia and the action of nascent nitrogen, Uhlig4 showed how readily pure molecular nitrogen reacts with and diffuses into 18-8 stainless steel at 1150°C. He also pointed out how readily nitrogen diffuses out of 18-8 stainless steel when heated in pure dry hydrogen, and these thorough investigations on the subject show that commercial stainless steels are nitrogen-bearing, since they are melted in air. The effects of nitrogen in stainless steel, particularly the 18-8 Cr-Ni type, previously have received considerable attention." In 1926, it was pointed out

Jan 1, 1956

By K. L. Fetters, F. M. Walters

ALL previous records were broken by the Iron and Steel Division, in the number of sessions, the number of papers, and the attendance. In addition to ten papers (all preprinted) on properties, structure, aid hardenability of, carbon and alloy steels, eight formal papers were presented on one or more phases of steelmaklng, and a symposium on the determination of hydrogen and nitrogen in steel. This last started at 2 p.m. and was going strong with more than a third of the audience still present at 6 p.m.

Jan 1, 1944

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By C. H. Herty

AN earlier paper on absorption of sulfur by the slag in the basic open-hearth furnace included a brief discussion of the absorption of sulfur during the melting period. The data available at that time showed that the amount of sulfur absorbed by the melting scrap was proportional to the sulfur content of the furnace gases, and the following statement was made: "The conclusion may be drawn from these results that if a gas entirely free from sulfur were used during the melting, any iron in direct contact with the gases would be completely, or nearly completely, desulfurized before it reached the bath proper." The experimental work discussed herein deals with absorption of sulfur by the melting scrap when fuels with both high and low-sulfur content were used. Before taking up the experimental work let us consider the process as a whole as to the "flow" of sulfur. The input of sulfur occurs in: 1, the hot metal charged; 2, the scrap; 3, the stone or lime charged; 4, the ores charged; and 5, the gas. Sulfur goes out of the furnace in the steel, the slag and the gas. The distribution of sulfur in the furnace depends on the sulfur concentration in each of these materials and on the equilibrium conditions between them.

Jan 1, 1926

By T. K. Redden

Protective coatings based on the formation of a surface coating of nickel aluminide (NiAl) were applied to the nickel-base superalloys IN 100, SEL 15, and U-700. Coated specimens were exposed to an oxidizing environment at temperatures between 1600 and 2200 F for times up to 1000 hr. The oxidation resistance and stability of the coating were evaluated by weight gain measurements, metallographic examination, and X-ray diffraction study of surface oxides and coating. The composition of the coating and diffusion zone was determined by electron microprobe traverse of samples before and after high-temperature exposure. Intermediate phases formed in the coating and diffusion zone were identified by X-ray diffraction in situ and after electrolytic extraction. The outer coating was found to consist of the inter-metallic compound, NiAl, while the diffusion zone contained MC, M23C6 or M6C carbides, and a phase in a matrix of NiAl + Nidl. Oxidation resulted in formation of an A1203 n'ch scale containing some Tz02. Depletion of aluminum during oxidation resulted in degradation of the outer coating to Ni3Al and the nickel alloy matrix. Diffusion of aluminum into the base metal was found to be slight and did not influence coating life significantly. The o formed in the diffusion zone during coating decomposed during elevated-temperature exposure to form stable carbide phases characteristic of the base metal. Diffusion zone phase changes were found to have no effect on the life of the aluminide coating in the oxidizing envzron?nent. THE oxidation resistance of many high-strength nickel-base superalloys is inadequate for extended exposure at temperatures above about 1600°F. In addition, some applications for these materials require that they be exposed to environments containing sulfur compounds and sodium salts which can cause surface attalk known as sulfidation or hot corrosion. In order to provide the necessary corrosion resistance to the high-strength alloys, protective coatings based on an aluminizing process have been developed. These processes, usually based on a pack cementation technique, result in the formation of a NiAl-rich outer coating layer either during the coating process or by a subsequent diffusion treatment. The performance of the aluminide coatings is affected by interactions between the coating layer and the base metal both during the coating process and during subsequent exposure at elevated temperatures. Knowledge of these interactions is required to guide the development of coatings capable of longer life and improved reliability. Goward et al.' recently reported the metallurgical factors which influence coating per- formance on MAR-M200. The present work is concerned with correlating the interactions and performance of coating compositions on several representative materials. EXPERIMENTAL PROCEDURES Materials. Three cast nickel-base superalloys which are used for turbine buckets in air-breathing engines were studied: IN 100, U-700, and SEL 15. Their chemical compositions are given in Table I. The alloys were vacuum-induction-melted and cast to slabs approximately 0.3 in. thick from which rectangular specimens 0.25 by 0.5 by 1 in. were machined. Coating Procedures. The machined specimens were coated by CODEP processes which were developed at the author's laboratory. These are based on pack cementation in various media to deposit either aluminum or aluminum in combination with titanium. The coating process which deposits only aluminum is designated CODEP-C, while the CODEP-D process deposits titanium in combination with aluminum. The CODEP-D process was applied only to IN 100. Both CODEP processes are applied at 1950" or 2000°F for 4 hr without need for a subsequent diffusion treatment. An outer coating about 1 mil in thickness is produced by these processes. Test Procedures. Coated specimens were exposed to static oxidation for periods ranging from 24 to 1000 hr at temperatures of 1600" to 2200°F. Terminal weight gain measurements and visual examination were used to evaluate oxidation resistance. including oxide spalling and coating failure. Both as-coated and exposed specimens of each alloy were studied by metallographic examination, electron microprobe analysis (EMA), and X-ray diffraction analysis either of the exposed surfaces or of phases extracted from the coating and diffusion zone. RESULTS As-Coated Condition. The microstructures of as-coated conditions were generally similar, irrespective of base materials or the particular coating process. They are typified by IN 100 coated by CODEP-D as shown in Fig. 1. The predominately single-phase outer layer, area A, Fig. 1, was identified by X-ray diffraction as the intermetallic compound NiA1. The NiAl zone extended inward to the original base metal interface. The diffusion zone, area B, Fig. 1, included carbide phases, a lamellar phase oriented perpendicular to the base metal surface, and a matrix phase consisting of a mixture of NiAl and Ni3Al. The phases in the diffusion zone were electrolytically extracted using a 10 pct HCl in methanol solution at approximately 1.3 amp per sq cm. The extracted phases were found to be M6C, MC, or M=C6 carbides and o as shown in Table I1 for each of the alloys. The d spacings from a typical diffraction pattern are

Jan 1, 1969

By Henry M. Howe

THIS paper gives the composition of the iron and slag at different stages in the "air-furnace" process of preparing "hard metal," or white cast-iron, for conversion into malleable cast-iron by annealing. The details of the process are given in an appendix. One of us had been trying for years to work some chemist of some of our malleable-iron works up to a degree of enthusiasm which would lead him to make such au investigation. It would have had the advantage of the greater familiarity with the conditions which one habitually on the spot must have. Failing in this, he made use of an opportunity which presented itself of taking samples here represented, with such fairness as the conditions permitted, holding firmly that a rough approximation to the truth is better than the complete lack of data, or that a bird in the hand is worth two in the bush. We hope that this attempt may stimulate others effectively to duplicate this work, and thus correct or confirm it. Our results are shown in Table I. and graphically in Figs. 1 and 2. Discussion.-At the time when the first two samples were taken, the metal and slag were still too sluggish to permit fair sampling, and not until sample 6 were the conditions really favorable, because at the time of the fourth sample the metal was not fully melted, and even at the time of sample 5 it was still sluggish. Indeed, the slag was probably very heterogeneous throughout, because it took up silica and alumina rapidly from the bottom, and because it was so siliceous as to be sluggish at this relatively low temperature. This hetero-geneousness is exaggerated in the two samples of slag 8, apparently by the great viscosity due to its extraordinary acidity. Note that the manganous oxide of one sample is about two and

Mar 1, 1909

By T. A. Rickard

The history of this State is that of one generation. Thirtysix years only have elapsed since the birth of that beneficent industry whose footsteps were the first to traverse the wilderness of the prairies and penetrate the solitude of the mountains. So soon is history made. The men who halted on the rolling plain where Denver now stands and gazed westward at the snow-clad ranges in eager questioning of their possibilities of golden wealth, have lived to see a noble city built where once their camp-fires burned, and have participated in the discovery of a magnificent series of productive mines amid the mountains which seemed at that time the Ultima Thule of their pilgrimage. To those who investigate the workings of our complicated mining and metallurgical industries, the story of their evolution from humble beginnings will appear an instructive romance. The record that tells it presents features common to the growth of modern mining regions, but also bears aspects peculiar to

Jan 1, 1897

By H. Sigurdson, C. H. Moore

Extensive studies have been carried out on electric furnace and blast furnace slags obtained in the winning of iron from its ores. These slags normally consist of elements of the gangue minerals present in the ores, as well as the added flux materials. In consequence, melts of CaO, MgO, Al2O3 and SiO2 can be considered as representing typical slag compositions. When a slag of this composition cools, it usually crystallizes according to predictions possible from an equilibrium diagram of these constituents, providing the melt is not undercooled to form glass. The melt is either viscous or fluid, depending upon the ratio of binary cations to silica, and crystallizes easily or forms a glass for the same reasons. If the melt is not overheated so that carbides of the metal components of the slag are formed and if the composition of the slag is so adjusted that it has a high fluidity, liquid equilibrium is attained and the slag can be held in a liquid state for extended periods of time. Upon tapping, the slag crystallizes into minerals, the type and proportion of which are determined by the melt composition. Since equilibrium is attained, the holding period is not critical. In melts containing a large increment of titanium, however, the normal slag procedures are not applicable. Titanium, as one of the atomic transition elements, is, at elevated temperatures, capable of being reduced to form metalloid compounds much more readily than the refractory oxides present in normal slags. In consequence, an oxide melt containing titanium never reaches equilibrium in a reducing environment, but continues to shift its composition until cooled. If melts of this nature are cooled and samples submitted to metal-lographic and X ray analysis the course of reaction and crystallization in this type of slag can be determined. Preparation of Slag The slags investigated fell into the system CaO-MgO-TiO2-Al2O3-SiO2 and were produced from ilmenite ores reduced by carbon in an electric furnace. Since the equilibrium series1 and the laboratory smelting of ilmenite2 are described in two of the accompanying papers, detailed description of the smelting procedure is not required here. However, certain essentials must be mentioned. Two types of melts were used to produce slags studied in this investigation. The first series of smelts made to determine proper flux addition were produced in a 4 lb Ajax induction furnace. The charge, consisting of ore with the proper flux addition, was heated in a graphite crucible until fluid, held fluid for a sufficient time period to obtain 1-5 pct FeO content, and poured. Because of the small size of the charge only the final sample of these melts could be examined. In the melts made in the 50 lb arc furnace, however, grab samples taken at 10 min. intervals between time of initial melting and final pouring were available for examination. These samples allowed a much clearer picture of the course of reaction and crystallization. amounts of ferrous oxide and reduced titanium compounds is opaque to transmitted light. Therefore, all petro-graphic studies had to be made on polished slag sections. A representative sample of slag was cut or broken, mounted in a thermosetting plastic, ground flat using 400 grit silicon carbide, the coarse scratches removed with 600 grit silicon carbide and polished on billiard cloth using levigated alumina. Rouge was avoided because of the entrainment of the red particles in pores in the slag, causing a possible confusion with some of the mineral phases. In order to prevent sample projection above the plastic surface red bakelite was used to hold the sample, and backed up with clear lucite. In this manner sample labels could be permanently retained in the mounting. The polished samples were examined on a Bausch and Lomb metallograph at magnifications of 250 X, 500 X, 1000 X and 1800 X. The instrument was equipped for examination of specimens under bright field illumination and with crossed nicols. A magenta tint plate to aid in color tone differentiation was also used. Petrology of Slags In order to determine the composition and mineral relatinos of a previously unreported system petrologically, it is essential that the starting composition, reaction temperature and final composition be known. The chemical composition of the ilmenite ore used in these smelts is given in Table 1, and the complete analysis of a typical high titanium, low iron slag is given in Table 2. In the winning of TiO2 from ilmenite by a smelting process it is necessary to produce a slag which will melt at an economically feasible temperature, remain molten as the iron is removed by reduction, be fluid enough to be readily removed from the furnace, contain a high percentage of TiO2 and a low percentage of reduced titanium com-

Jan 1, 1950

By Philip D. Wilson

IT has been my privilege to read the article prepared by R. S. Dean entitled "Production of Alumina from Low-Grade Domestic Materials" which appears on another page of this issue. Dr. Dean should be congratulated on the preparation of such an erudite and scholarly dissertation on bauxite and on the work which the Bureau of Mines has been doing in connection with the development of processes to use low-grade domestic materials.

Jan 1, 1943

By COREY C. BRAYTON

OUR first air travel began at Barranquilla on a trip to the platinum dredging-operations at Andagoya. The fare is based on a minimum weight of passenger, and I will have to admit that the minimum is too low. To make this trip by boat would have necessitated going back to the Canal, thence down to Buena Ventura, and up the San Juan river, which would have taken, counting delays, two or three weeks. The time by Scadta airplane was six hours. We stopped at Cartagena for a day to look over that historic city. The route from there lay along the north coast to the mouth of the Atrato river, then up this river, over the jungle, and over a divide some 300'ft. in elevation and down the San Juan river a few miles to Andagoya at the junction of the Condoto. The General

Jan 1, 1930

By J. E. Tobey

NATIONAL DEFENSE should not create a dilemma in coal utilization such as obtained during the World War. Even under the heavy pressure of a total preparedness program there should be a smooth flow of the right coals from mines to plants. The more than 100,000 industrial plants of the nation must he served with coal of such characteristics and qualities for their individual requirements that no loss of production due to coal failure shall occur. This problem challenges the ingenuity and cooperativeness of producers. transportation executives, consumers and engineers.

Jan 1, 1941

By William J. Coulter

WITHIN the United States the problem of meeting maximum production by our metal mines has been solved by: (1) Conservation of man power by mechanization. (2) Increasing man-power efficiency as expressed in tons per man-shift by the adoption of new and more efficient methods. (3) Production from submarginal properties made possible by some form of government subsidy. (4) Selective mining of high-grade areas. (5) Drawing on broken ore reserves and reducing advanced development work to a minimum. (6) Making maximum use of available equipment. (7) Repairing equipment that normally would be replaced. (8) Working a seven-day week on a three-shift basis to get maximum use of equipment and man power. (9) Adoption of incentive plans to increase maximum efficiency and unit production. (10) Important advancement in metallurgy, resulting in larger recoveries. (11) Improvements in safety, health, and general working and living condi-

Jan 1, 1945

By Albert F. J. Bordeaux

INTRODUCTION. THE following general survey of the character and present condition of the silver-mines of Mexico, though not offered as a detailed treatise, has been prepared with care, is believed to he generally up-to-date, and is offered as a summary which may be found useful by mining engineers. Mexico has ranked for several centuries first among the silver-producing countries. It is now second as copper-producer, and seventh as gold-producer, with a fast-increasing output every year. The total amount of capital invested in its mining- and smelting-works is more than $250,000,000, while the yearly metallic production is $160,000,000. There are more than 20,000 recorded mining properties. The silver-mines of Mexico represent deposits of three principal classes: (1) veins and stock-works in eruptive rocks; (2) fissure-veins crossing the crystalline schists, granite, diorite, etc. ; and (3) veins and replacement-deposits in limestone. The true fissure-veins in some districts contain (in value) more gold than silver. In other deposits, the silver is decreasing in depth, leaving galena and zinc-blende as the principal ores.

Jan 9, 1908

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

By S. G. Lasky

EVENTS during and since the war indicate that the nations of the world are trying to initiate an era of international co-operation. Definitions and objectives include social, economic, and human considerations no less than political considerations. The mineral resources of the world and the absolute and relative position of each nation enter into this situation. The possible use of armed might, the application of sanctions, the international flow of commerce, the ways in which this flow may encourage or hamper international well-being, and the influence of international and domestic well-being upon one another are all matters that must take mineral resources into account. If the United States is to act wisely and forthrightly in such matters we must be thoroughly informed as to our position with respect to mineral resources. What is the mineral position of the United States? A variety of widely conflicting opinions are held in authoritative and intelligent quarters: (1) For practical purposes our mineral resources are already exhausted.

Jan 1, 1946

By M. A. Hunter

IN the present state of public affairs, the reviewer turns from his traditional role of recording the progress made in research during the year and views the whole situation in which he finds himself in direct relation to the immediate needs of the nation. The slow progress of research year by year fades into comparative insignificance. The sum total of that research in all the years which have past becomes of importance only in direct relation to the extent to which we have translated or can immediately translate it into in¬dustrial production. For in a wartime economy immediacy is of paramount importance. The outcome of the war is being determined by our ability to pro¬duce and fabricate the metals and alloys which we require for its prosecution. Aside from iron and steel which lie outside the limits of this review, the most important of the nonferrous metals now needed in wartime production are aluminum, magnesium, nickel, chromium, and manganese. Some remarks on their production and fabrication follow.

Jan 1, 1942

By G. J. Ballmer

Trucks Are Valuable Auxiliary Haulage Units in Rail Pits For: ( I ) Making railroad grades (2) Establishing benches (3) Making new dropcuts

Jan 10, 1951

Jan 1, 1931

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

By Ta M. Li

Expanded mine-mill capacity and greater operating flexibility are part of the dramatic changes taking place in the Tennessee mining operations of Asarco, Inc. Climaxed by the recent start-up of the $6.3 million Young mill in September 1975, Asarco has pushed Tennessee back into number one position as the leading zinc mining state. Furthermore, start-up of the Young mill is expected to insure a much-needed and continuing domestic zinc supply, at a time when US mines can only supply one-half of 1975 domestic consumption.

Jan 5, 1976